CCNA Routing Protocols

CCNA Guide to Cisco Networking Fundamentals Chapter 7 Routing Protocols

Objectives Differentiate between nonroutable, routed, and routing protocols Define Interior Gateway Protocols, Exterior Gateway Protocols, distance-vector routing protocols, and link-state routing protocols Explain the concepts of count-to-infinity, split horizon, split horizon with poison reverse, and hold-down timers CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Objectives (continued) Describe, configure, and monitor the interior routing protocol RIP Explain static routing and administrative distance Configure static routing and default routes CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Nonroutable Protocols In the early days of networking, networks were small collections of computers linked together For the purposes of sharing information and expensive peripherals Early networks were sometimes configured as peer-to-peer networks Computers communicate with and provide services to their “peers” All communication occurs on the same network segment CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Nonroutable Protocols (continued) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Nonroutable Protocols (continued) Several nonroutable protocols exist in today’s networking world NetBEUI (NetBIOS Enhanced User Interface) The most common nonroutable protocol Ships with all Microsoft Windows operating systems NetBEUI cannot scale into large internetworks Cannot hold Network layer information in its network header CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Routed Protocols Routed protocols Have packet headers that can contain Network layer addresses Developed to support networks consisting of multiple networks or subnetworks Protocols that can carry Network layer information Transmission Control Protocol/Internet Protocol (TCP/IP) Internetwork Packet Exchange/Sequenced Packet Exchange (IPX/SPX) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Routed Protocols (continued) For routed protocols to work on a network Every device must be configured with a unique IP or IPX address ( logical address ) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Routing Protocols Routing protocols Protocols used by routers to make path determination choices and to share those choices with other routers Hop count The number of routers a packet must pass through to reach a particular network Metric A value used to define the suitability of a particular route Routers use metrics to determine which routes are better than other routes CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Routing Protocols (continued) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Routing Protocols (continued) Autonomous system (AS) Uses Interior Gateway Protocols as routing protocols A group of routers under the control of a single administration Interior Gateway Protocols (IGPs) are Routing protocols used within an AS Exterior Gateway Protocols (EGPs) Routing protocols used to route information between multiple autonomous systems CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Routing Protocols (continued) Examples of IGPs Routing Information Protocol (RIP) Interior Gateway Routing Protocol (IGRP) Enhanced Interior Gateway Routing Protocol (EIGRP) Open Shortest Path First (OSPF) Example of EGP Border Gateway Protocol (BGP) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Two Types of IGPs Distance-vector routing protocols Broadcast their entire routing table to each neighbor router at predetermined intervals The actual interval depends on the distance-vector routing protocol in use Varies between 30 and 90 seconds Sometimes referred to as routing by rumor Suffer from slow time to convergence A state where all routers on the internetwork share a common view of the internetwork routes CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Two Types of IGPs (continued) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Two Types of IGPs (continued) Distance-vector routing protocols (continued) Routing loops Often referred to as count-to-infinity problems Loops, without preventive measures, will cause packets to bounce around the internetwork infinitely Defining a maximum One of the easiest ways to limit count-to-infinity problems Split horizon and split horizon with poison reverse Two other common ways to prevent routing loops when using distance-vector routing protocols CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Two Types of IGPs (continued) Distance-vector routing protocols (continued) Hold-down timer Another common technique used to stop routing loops Allow a router to place a route in a state where it will not accept any changes to that route Link-state routing protocols Use link-state advertisements (LSAs) to inform neighbor routers on the internetwork LSAs contain only the local links for the advertised router CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Two Types of IGPs (continued) Link-state routing protocols (continued) Shortest Path First (SPF) algorithm Uses the link information to compute the routes Router CPU resources are used instead of bandwidth Link-state packets (LSPs) Packets used to send out LSAs Allow every router in the internetwork to share a common view of the topology of the internetwork A link-state routing protocol floods , or multicasts, LSPs to the network Later updates will be triggered updates CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Two Types of IGPs (continued) Link-state routing protocols (continued) Routers using link-state protocols must be configured with more memory and processing power Than those using distance-vector routing protocols Link-state routing protocols such as OSPF are much more complicated to configure on the routers CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Routing Information Protocol Routing Information Protocol (RIP) The easiest Interior Gateway Protocol to configure is RIPv1 A distance-vector routing protocol that broadcasts entire routing tables to neighbors every 30 seconds RIP uses hop count as its sole metric RIP has a maximum hop count of 15 As a result, RIP does not work in large internetworks RIP is capable of load balancing RIP is susceptible to all the problems normally associated with distance-vector routing protocols CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Enabling RIP Routing CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Enabling RIP Routing (continued) To start configuring RIP, you must: Enter privileged mode first Enter global configuration mode on your router Enable RIP with the router rip command CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Enabling RIP Routing (continued) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Configuring RIP Routing for Each Major Network network command Turns on RIP routing for a network An individual network command must be issued for each separate network directly connected to the router show ip route command Displays a router’s routing table Administrative distance A value used to determine the reliability of the information regarding a particular route Administrative distances range from 0–255 CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Configuring RIP Routing for Each Major Network (continued) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Show ip protocol and debug ip rip Commands Commands used to monitor RIP A route is considered invalid if six consecutive update intervals pass without an update from that route Flush interval The time at which a route will be totally removed from the routing table if no updates are received debug ip rip command Displays real-time rip updates being sent and received and places very high processing demands on your router, which could affect network performance CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Show ip protocol and debug ip rip Commands (continued) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Interior Gateway Routing Protocol IGRP is a proprietary distance-vector routing protocol Created by Cisco to solve some of the problems associated with RIP A larger hop-count metric allows IGRP to be used on larger networks IGRP supports a hop count of 255, although 100 is the default if hop count is configured to be used as a metric The metric maximum-hops command allows you to set the maximum hop count for IGRP CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Interior Gateway Routing Protocol (continued) The default metrics for IGRP are bandwidth and delay only Metrics that can be configured for IGRP Hops: number of routers between source and destination networks Load: the load on a link in the path Bandwidth: the speed of the link (default) Reliability: measures reliability with a scale of 0 to 255 Delay: the delay on the medium (default) MTU: the size of the datagram CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Static Routing Some networks are so small that using a routing protocol creates: Unnecessary traffic An inefficient use of router processor resources Stub routers Routers with only one route out Stub routers are usually the last router in a chain Stub networks Networks with one route to the Internet Static routes are configured by a network administrator using the ip route command CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Adding Static Routes CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Adding Static Routes (continued) Syntax for the ip route command: ip route [ destination network address] [destination network mask] [ ip address next hop interface] [administrative distance] Examples: ip route 172.32.3.0 255.255.255.0 172.32.2.2 ip route 172.32.4.0 255.255.255.0 172.32.2.2 CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Adding Static Routes (continued) Changing administrative distance The ip route command allows you to configure an administrative distance Unless you add an administrative distance value to the end of your ip route command The administrative distance will be 1 Configuring a default route All packets that are not defined specifically in your routing table will go to the specified interface for the default route CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Adding Static Routes (continued) Configuring a default route (continued) A default route is a type of static route that the administrator configures You can use the ip default-network command or the ip route 0.0.0.0 0.0.0.0 command to configure a default route Default routes are sometimes called quad zero routes A default route is used only if no other route to a network exists in the routing table CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Adding Static Routes (continued) CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Summary Some protocols are designed to be used in small networks without the need for Network layer addressing The most common nonroutable protocol is NetBEUI Other protocols were designed with the ability to move between multiple networks via Network layer addressing The most common routed protocol suite is TCP/IP CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Summary (continued) Protocols must be available that can find the best path throughout an internetwork and relay that information to routers Routing protocols are classed in two major groups: Interior Gateway Protocols and Exterior Gateway Protocols Interior routing protocols are further divided into distance-vector and link-state routing protocols These two types of Interior Gateway Protocols use very different methods to determine the best path in an internetwork CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

Summary (continued) Distance-vector protocols periodically broadcast entire routing tables to neighbor routers Link-state protocols multicast link updates to routers in their area upon startup and when network topology changes Two common distance-vector IGPs discussed in this chapter are the Routing Information Protocol and the Interior Gateway Routing Protocol Static routes are used to conserve bandwidth and lower memory and CPU load on a router while still allowing for correct routing table creation CCNA Guide to Cisco Networking Fundamentals, Fourth Edition

CCNA Routing Protocols

Recommended

More Related Content

What's hot (20)

Viewers also liked (17)

Similar to CCNA Routing Protocols (20)

More from Dsunte Wilson (17)

Recently uploaded (20)

CCNA Routing Protocols