Advanced View of Atmega Microcontroller Projects List - Projects Tutorials Code Library for Atmels Atmega32 AVR.pdf

8/22/23, 1:14 PM Advanced View of Atmega Microcontroller Projects List - Projects Tutorials Code Library for Atmels Atmega32 AVR
https://atmega32-avr.com/advanced-view-atmega-microcontroller-projects-list/ 1/178
Advanced View of Atmega Microcontroller Projects List
List of Projects using Atmega Microcontroller with advance view:
1. The Atmel-ICE Debugger 1. Introduction 1.1 Introduction to the Atmel-ICE Atmel-ICE is a highly capable development tool
designed for debugging and programming Atmel SAM and Atmel AVR microcontrollers based on ARM Cortex-M
architecture. It provides On-Chip Debug capability and supports various interfaces and families of microcontrollers, including:
Programming…... Listed under: Other Projects
2. Hard Drive Based AVR Programmer The project we are presenting differs from the one initially proposed. Our original plan
was to construct a WWVB time-code receiver capable of extracting highly precise time information from a 60 kHz signal
provided by the National Institute of Standards and Technology (NIST). However, due…... Listed under: Microcontroller
Programmer Projects
3. Setup External programmer in Atmel Studio This tutorial provides step-by-step instructions on how to integrate an external
programmer into Atmel Studio 7.0. By setting up the external programmer, you will be able to flash the AVR board directly
from Atmel Studio without the need to switch to the "Universal_GUI.exe" application. This…... Listed under: Microcontroller Programmer Projects
4. Program Artou ATmega32 Development Board Program an AVR development board without installing any software.
ExpressIDE and AVRdudess. Story ATmega32 Board Artou makes a development board with the ATmega32 processor. Like an
Arduino Uno but this processor adds a PORTA that is not on the ATmega328p. We will toggle the four bright LEDs next to…...
Listed under: AVR ATmega Projects
5. Simple Standalone ATMega328p Microcontroller Story A digital clock is a type of clock that displays the time using numerals
or digits, rather than using a dial and hands. These clocks typically use an electronic display, such as an LED or LCD screen, to
show the time. Digital clocks…... Listed under: Clock Projects
6. Arduboy on ATMega4809 Porting Arduboy to the ATMega4809 and making it run on a Arduino Nano Every. Story After
learning about the Arduboy on ATMega4809 challenge, we decided to join in the fun and port Arduboy to a new
microcontroller. In the spirit of staying with true 8…... Listed under: Other Projects
7. Another ATMEGA4808 Development Board Another ATMEGA4808 Development Board turned out looking very well but
highlighted some issues with supply and sourcing of components. Story ATMEGA4808 – An Improvement on my previous
design? Or Not… When I first started playing around with the ATMEGA4808, I was impressed as well as…... Listed under: Other
Projects
8. ATMEGA4808: Better than ATMEGA328? In this final part of the series, I look at the ATMEGA4808. This may just be the
replacement for the ATMEGA328 that I have been looking for. Story The ATMEGA4808 provides a very attractive solution to
replace the trusted ATMEGA328 or standard Arduino UNO /NANO.…... Listed under: AVR ATmega Projects
9. ATmega Alien Themed Slot Machine Story This project is my implementation of an alien themed slot machine using two
ATmega328P-PU micro-controllers. I was inspired by Cory Potter's Alien Invasion Slot Machine, and I wanted to expand on
that idea. The slot machine is for entertainment and educational purposes only. I tried my…... Listed under: Game -
Entertainment Projects
10. AVR-GCC Background I've written dozens of programs using the Arduino IDE and using other tools like the ARM mBed
toolchain. My priority for this week was to familiarize myself with avr-gcc and the Atmel libraries. Week 4 Board Programming
I had already programmed my Week 4…... Listed under: Other Projects

11. ATmega328P Standalone Board In this step-by-step tutorial we will learn how to build a standalone Arduino UNO compatible
ATmega328p board. ATmega328P Bare minimum configuration Before building our standalone ATmega328P chip Arduino
compatible board, let’s take a look at the awesome Arduino UNO board and see the main components…... Listed under:
Other Projects
12. SPATIAL AUDIOMAP Project Introduction Our project is a spatial audio map of Collegetown that allows the user to use a
joystick to virtually travel around the Collegetown crossing area and hear surrounding, directional sound. Our project takes
inspiration from Street View, an interactive technology featured in Google…... Listed under: Sound - Audio Projects
13. Snorecorder with SD Logging Introduction Sound Byte The Snorecorder detects snoring sounds from a sleeping person and
records the time and intensity of each snore. The data is written to an SD card, which can be easily viewed on a personal
computer. Synopsis The Snorecorder determines and records snore…... Listed under: Sound - Audio Projects
14. ProxMidi A capacitive MIDI sequencing platform Introduction ProxiMIDI is a MIDI code generator, that takes its inputs from a
user using Atmel’s Capacitive touch and Proximity technology. It can generate sound signals for 4 notes of 3 instruments and
vary the tempo, volume and sound depending upon the proximity inputs. The…... Listed under: Other Projects
15. Some Assembly Required What We Did We created an autonomous robot that explores the world in linear trajectories while
avoiding obstacle using IR range-finding. The robot is a Venom RC car altered to be controlled by an Arduino Uno
programmed in AVR Assembly (a very low-level programming language…... Listed under: Other Projects
16. How to Install and Setup EAGLE Introduction Printed circuit boards (PCBs) are the backbone of every electronic gizmo out
there. They're not flashy like those microprocessors, or abundant like resistors, but they're essential to making all
components in a circuit connect together just right. We LOVE designing PCBs here at SparkFun.…... Listed under: AVR ATmega
Projects
17. Floating Away with AmForth 1 Starting Forth Forth[3] is a flexible, stack-based programming language that is ideal for
embedded use. It has an amazing power to weight ratio; it can do a lot with limited resources. Forth zealots take this as one
of many signs that Forth is the One-True-Language.…... Listed under: Other Projects
18. Programming for AVR This project was done in order to experiment with the Automotakit breadboard board which is based
on the ATMEGA256A3U chip. The use of a DAC, ADC , low pass filter, PWM, basic I/O, current control, clock setup, and
interrupts on an Atmega chip are some of the…... Listed under: Other Projects
19. Work Progress I have been working on input and output devices communication for weeks. For those weeks, I spent so many
times on the ESP32 debugging and got nothing solved, which makes me be so despair about the foreseeable failure of my
final project. This wildcard week,…... Listed under: Other Projects
20. Embedded Programming 1. Programming Board Blinking Code using Arduino environment CODE: I started with code code
from Jaclyn Berry's page : const int buttonPin = 7; const int ledPin = 2; int buttonState = 0; void setup() { pinMode(ledPin,
OUTPUT); pinMode(buttonPin, INPUT); } void loop() { buttonState…... Listed under: Other Projects
21. Using the GNU AVR toolchain on Windows 10 Introduction This page attempts to describe a procedure for installing a
complete GCC-based toolchain on a modern Windows system. I've developed these instructions on my Windows 10 machine,
but they should work for versions of Windows as far back as Windows 7. On older versions, you might…... Listed under: Other
Projects
22. Programming the AVR microcontroller with GCC, libc 1.0.4 Introduction Many people where interested in microcontroller
programming after the article which I wrote in 2002. However this first step to get the development environment up and
running is the hardest. If something does not work then you have absolutely no clue where the fault…... Listed under: AVR
ATmega Projects

23. How to use I2C / TWI (Two Wire Interface) in AVR ATmega32- (Part 36/46) Code explanation for MASTER Controller: Step 1:
Initialization of master. Initialization of MASTER means to set the TWI clock frequency (SCL). It is done by setting bit rate in
TWBR and pre scaler bits in TWSR. …... Listed under: Other Projects
24. Stand Alone Arduino ATmega328p Step 1: Components and Where to Start I've started from the Arduino official site:
https://www.arduino.cc/en/Main/Standalone where I've taken this picture, and where there is the list of all the components
that you have to buy. Just the components that are showed in this picture. (…... Listed under: Other Projects
25. ARDUINO CLONE With ATMEGA328-PU Non P Step 1: The Beginning Last week I decided to make a classic Arduino clone
with an ATMEGA328P-PU. I seemed to be so easy and quick but a very bad surprise for me: I odered the cheaper
ATMEGA328-PU (non P!!) that is to say: non pico…... Listed under: Other Projects
26. Worry-Free Automatic Timed Plant Feeder Introduction The following diagram shows the system schematic. It contains the
several major blocks: ATmega 323 is the CPU of the system. 5 VDC power supplier: an adaptor first transforms 110 VAC 60 Hz
into 9 VDC; then a regulator keeps VCC stable at 5…... Listed under: Other Projects
27. Networking Board Design For part of my final project I want to make my own USB audio recording device. So I’ll try to
develop all the necessary electronics this week. I have the analog circuitry I need from inputs week. But I don’t have a board
ready…... Listed under: Other Projects
28. 10 Best AVR Development Boards For Engineers And Hobbyists 2019 Atmel’s AVR series of controllers is one of the most
popular with student and hobbyists. Any beginner in electronics or even professionals for that matter would appreciate an
excellent development board. Development boards rid the user of the tedious tasks of prototyping and debugging
necessary…... Listed under: AVR ATmega Projects
29. Programming the Microchip ATmega328P in C Introduction This document describes how to program the Microchip
ATmega328P microcontroller in C using the Avr-GCC toolchain. Students can download the software and install it on their
computers by visiting a few websites. Atmel used to manufacture the ATmega328P microcontroller until it was acquired by…...
Listed under: Arduino Programmer Projects
30. Automatic Egg Incubator Many factors contribute to the high demand for egg incubator around the world. A person who is
interested in birds would like to raise ornamental birds, but he couldn't find or obtain a broody bird as such; nonvegetarians
eat birds, but they are often forced…... Listed under: AVR ATmega Projects, Motor Projects
31. Atmel AVR Programmer USB Circuit Atmega8 Via the USB port of your computer that you can program Atmel series
microcontrollers ISP port with stylish design a programming circuit. Prepared with eagle pcb circuit usb programming. are
schematic drawings. To use the circuit to inspectors ATmega8 avr-doper-mega8-12mhz_a.hex need to download the file.
Simplified Version…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
32. What is AVR Microcontroller : PinOut, Working & Its Applications The advanced version of a microprocessor is a
microcontroller that includes a CPU, Interrupts controller, RAM, ROM, I/O unit, etc. A microcontroller is mainly used for the
operation of high-speed signal processing in an embedded system. So it performs like a major component while designing
an embedded system.…... Listed under: Microcontroller Programmer Projects
33. Setting up Atmel Studio for USBasp and AVR Programming It can be a lot confusing someone for who just started
programming in AVR environment. Atmel studio is the best IDP [Integrated Development Platform] for AVR programming
and embedded system development. It takes awful lot of time just to get installed. But once you’re done…... Listed under:
Microcontroller Programmer Projects
34. Getting Started with Atmel Studio Introduction Atmel, AVR microcontrollers (MCUs) are very easy to use. All AVR
microcontrollers require Integrated Development Environment(IDE) such as Atmel Studio. Using this IDE, we can create,
compile, and debug programs on all AVR microcontrollers. Atmel Studio is available free of charge. To download and…...
Listed under: LED Projects
35. The LED Chasing Effect Project using Atmel AVR Microcontroller One of the interesting projects for most of the embedded
beginners enthusiasts or hobbyists is to build the LED chasing effect. In this project we are going to use both the Arduino IDE
and Atmel AVR Studio to program the AVR ATMega168 microcontroller, therefore you…... Listed under: LED Projects

36. GETTING STARTED WITH AVR MICROCONTROLLER GETTING STARTED WITH AVR MICROCONTROLLER.This article will make
you familiar how to getting started with AVR Microcontroller. You will learn each and every thing about AVR microcontroller.
What are the basic features of AVR microcontroller, Architecture of AVR microcontroller? Here you will also learn about…...
Listed under: Microcontroller Programmer Projects
37. AVR Tutorial for Beginners This tutorial series designed specifically for beginners. If you are a beginner looking to play with
cool electronic stuff, then you are going to find this very useful. This AVR tutorial for beginners series is going to cover all the
information about microcontrollers. I will…... Listed under: Other Projects
38. Attiny13A Motor Controller Board So here's something super interesting and useful, a motor controller board powered by an
Attiny13A to control a Brushed DC Motor. This Motor Driver uses PWM to control the gate of an N Channel IRFZ44N mosfet
by the Tap of a single button. I've…... Listed under: Motor Projects
39. XOD-powered Rechargeable Solar Lamp There are inexpensive solar garden/walkway lamps available at most home goods
and hardware stores. But as the old saying goes, you usually get what you pay for. The usual charging and illumination
circuits they use are simple and cheap, but the light output you get…... Listed under: Solar energy projects
40. Project Green Stations: Prototype Zero Introduction For our final project, we have designed and built a 'proof of concept'
prototype for Project Green Stations, an externally funded student group with the following mission statement: Project Green
Stations is all about changing the way people see the environment. Imagine the go-green…... Listed under: Solar energy
projects
41. Phased Array Speaker System Introduction For our ECE 4760 final project, we designed and built an array of 12
independently-controllable speakers to implement an acoustic phased-array system. The system samples a standard audio
input signal at approximately 44.1 kHz, and then outputs this signal to each of 12 speakers,…... Listed under: Sound - Audio
Projects
42. Infrared Universal Remote Control Introduction One of the more challenging aspects of owning a home entertainment
system is dealing with all the remote controls. My device is designed to tackle this problem. Specifically, the universal remote
control I implemented is able to learn the signals used by other remote…... Listed under: Other Projects
43. A Moving Alarm Clock Introduction We implemented a prototype for a moving alarm clock which runs away from the user
when they try to silence the alarm. It has all the features of a “regular” alarm clock: settable time and alarm, snooze, and
alarm on/off. The alarm clock displays…... Listed under: Clock Projects
44. Automated Drink Mixer Abstract The automated drink mixer takes orders from a push-button menu, and moves a regular 16-
ounce glass under a series of inverted bottles while dispensing specified amounts of mixers to make perfect non-alcoholic
beverages. Introduction If you’ve ever been to a crowded bar or restaurant…... Listed under: Motor Projects
45. ECE 4760 Final Project Report Introduction Most homes across the world lack a security system of any sort. The goal of our
project was to design a simple security system using the Atmel AVR ATmega1284p microcontroller that most people could
build without too much hassle for an affordable price. This…... Listed under: Other Projects
46. EYEMouse ELECTRO-OCULAR CURSOR CONTROL Introduction Several different approaches have been explored in developing a system to track eye
movements. These approaches span from measuring reflections of infrared light to using advanced imaging techniques to monitor specific features
within the eye. While a variety of reports exist on measuring infrared…... Listed under: Other Projects

47. Sign Language Glove Introduction We designed and built a glove to be worn on the right hand that uses a Machine Learning
(ML) algorithm to translate sign language into spoken English. Every person's hand is a unique size and shape, and we aimed
to create a device that…... Listed under: Other Projects
48. Segway Robot with Accelerometers Introduction The objective of this project was to create a two-wheeled balance bot able
to traverse a flat environment and adjust itself to shifts in position and weight, using a Proportional-Integral-Derivative (PID)
feedback control loop to keep the robot upright. The balance bot is essentially…... Listed under: Robotics - Automation Projects
49. AccelCar Our project aims to take the fun of a Wii Remote and translate it to real life. The AccelCar is a remote-controlled car
that is controlled by the way that a user tilts the remote, similar to the way Mario Kart Wii is played. The…... Listed under: Car
Projects
50. Smart Medicine Box Our ECE 4760 final project is to build a microcontroller based smart medicine box. Our medicine box is
targeted on users who regularly take drugs or vitamin supplements， or nurses who take care of the older or patients. Our
medicine box is programmable that allows…... Listed under: Medical - Health based Projects
51. Maple Bot Introduction For our final project in ECE 4760: Digital Systems Design Using Microcontrollers, we designed and
implemented a radio-controlled, map-learning, line-following robot. The robot traverses a map of lines with a configuration
that is initially unknown to a user. The robot discovers different types of…... Listed under: Radio Projects
52. LED Sketchpad In this project we built a sketchpad based on LED matrix display with microcontroller and resistive touch
screen control. We used a single point resistive touch screen to detect the user’s gesture and microcontroller’s analog/digital
converter (ADC) ports collects the data and convert it to…... Listed under: LED Projects
53. Virtual Object Grabber Introduction What is seeing without feeling? The field of Virtual Reality has recently been gaining much attention, with the
Oculus Rift and Google Cardboard paving the path of visualizing a world that is not physically there. But what if the virtual reality experience could
be…... Listed under: Other Projects

54. BOXING TRAINING INTRODUCTION In the modern American classic, Rocky IV, Ivan Drago (portrayed by Dolph Lundgren) is
shown utilizing a then-futuristic electronic punch meter (in addition to anabolic steroids) in his quest to triumph over Rocky
in one of the Cold War’s only face to face confrontations.…... Listed under: Other Projects
55. Ultrasonic Pursuit Automobile We’ve implemented an autonomous pursuit vehicle capable of chasing a designated target
using ultrasonic transmissions. The system is demonstrated by chasing a second, human-controlled, RC car. The pursuit unit
is equipped with a 24kHz transmitter and two 40kHz receivers, while the target unit has a…... Listed under: Phone Projects
56. GPS Navigator and Explorer The idea of the the project is to create a useful device for being able to get directions with any
specified path by use of waypoints rather than a path chosen by a GPS as well as being able to follow a path that is…... Listed
under: GPS Based Projects
57. ECE 4760 Space Invasion Introduction: What is Space Invasion: Space Invasion is a game in which a spaceship has to pass
through the walls, without crashing. There are monsters trying to kill the spaceship. So the spaceship has to destroy them
before getting destroyed. The game has no end,…... Listed under: Game - Entertainment Projects
58. Virtual Virtuoso a tool for conductors Introduction There are very few ways to improve one’s skills in conducting a live band.
Practicing by conducting a real band requires coordination of many people and conducting along to pre-recorded songs
does not provide feedback on the accuracy of the conductor’s selected tempo. The…... Listed under: Other Projects
59. Real-Time Pitch Shifter. Introduction "A device that pitch-shifts voice in real time" For our final project, we attempted to
implemented a real-time vocal pitch shifter. The system was designed to work as follows: a user speaks into a microphone,
their vocals are processed using a pitch shifting algorithm,…... Listed under: Sound - Audio Projects
60. Smart Sitter: A Do-it-Yourself Wireless Home Automation System Introduction Smart home technology has been surging in
popularity over the past decade. According to a recent poll, 46% of consumers believe that it is important that their current
or next home has smart technology. Many smart home technologies are expensive to implement and require…... Listed under:
Home Automation Projects
61. Virtual Bowling For our 4760 final project, we built a virtual bowling game interface on a black and white Television in which
the ball can be controlled by the glove which has the flex sensors and the accelerometer attached to it. There are 5 flex
sensors on…... Listed under: Other Projects
62. Bike Dash For our ECE 4760 final project, we designed and built a bicycle dashboard which displays the cyclist’s pedaling
power, speed, cadence, and distance to enhance training. The major motivation of this project was to replicate a commercial
product at a dramatically reduced price point. A…... Listed under: Other Projects

63. ukule-LED ukule-LED is a ukulele with LEDs embedded in its fretboard. These LEDs can light up in configurations
corresponding to different chords, which can aid the ukulele player in learning how to play certain chords, or can act as a
chord reference for a more advanced…... Listed under: LED Projects
64. Frequency Visualizer Introduction This project visually displays the frequency content of an audio signal using an 8X3 grid of
LEDs. A microphone and amplifier collect analog audio input which is sampled digitized using the MCU's analog-digital
converter. The samples are buffered and and a 32 point discrete…... Listed under: LED Projects
65. ECE 4760 Final Project: CPR Training Dummy on AVR Introduction For our ECE 4760 final project, we implemented an
interactive CPR training dummy which can coach the trainees through the CPR process with a LCD to display instructions. The
prototype CPR training dummy built is a budget-friendly one that contains a re-programmable Atmel ATmega1284…... Listed
under: LCD Projects
66. Bioelectrical Body Fat Analyzer Introduction For our final project, we have decided to use the microcontroller provided to
make a device which would measure body fat percentage of one's body. The basic principle behind this project is known as
bioelectrical impedance analysis. This technique uses a small alternating current…... Listed under: Other Projects
67. Speech Lock we designed and implemented a speaker recognition device that acts as a lock triggered by the sound of your
voice saying a specific passcode. The implementation uses hardware filtering from a microphone and many signal processing
concepts in software. All software and matching is implemented…... Listed under: Security - Safety Projects
68. Gesture based MIDI glove Introduction Musical Instrument Digital Interface, or MIDI, is a standard that describes a protocol,
digital interface and specific physical connections that allow electronic music devices and computers to communicate with
each other. For our final project, we created a MIDI glove that is capable of…... Listed under: Other Projects
69. ECE 4760: T-Bot Introduction "A resistive touch screen robot that follows a user-defined path input by drawing on the touch
screen."" We designed and implemented a robot that follows the path drawn on a touchscreen. The touchscreen is mounted
on top of the robot, and once the path…... Listed under: Robotics - Automation Projects
70. SingLock SingLock is a pitch-based security system based on ATMEL MEGA1284P microcontroller featuring two password
protection stages: one based on a 4-digit numeric personal identification number inputted via the keypad and another based
on two pitches inputted via the microphone. Most security systems we find today…... Listed under: Security - Safety Projects
71. The Skittles Mini-Factory Introduction The Skittles Mini-Factory is self-contained repackaging unit that separates Skittles by
color. Once separated, the Skittles are resealed in individual plastic bags. The Skittles are dispensed one at a time (either
automatically or manually) onto a light sensing module. Red, green, blue, and…... Listed under: Other Projects
72. ECE 4760 Final Project: Rapid Circuit Prototyping Introduction Our final project was to create a rapid prototyping machine for electrical circuits by
repurposing an old pen plotter that we fitted with an electrically conductive pen. Our plotter utilized an atmega 1284P to control the x and y-axis
motors, and to raise and…... Listed under: Circuits
73. REAL-TIME SCROLLING SPECTROGRAM INTRODUCTION This project implements a real-time scrolling spectrogram-style
visualization of an audio signal. We successfully displayed the frequency spectrum content in real time using a 4-bit grayscale
scrolling display on any NTSC television. The frequency spectrum of an audio line-in input or mic input is…... Listed under:
Other Projects
74. PALPi Lite Edition So this is the PALPi V4 which is a DIY Retro Game Console powered by a Raspberry Pi Zero W. The IDEA
here was to make a portable handheld gaming console that can run RETRO Games like Contra, Pokemon, Super Mario ETC.
[embed]https://youtu.be/8DVSS5S-lkQ[/embed] For Display,…... Listed under: Game - Entertainment Projects

75. Glowing RGB LED Magic Cube (WS2812) I fully designed from scratch every single piece of this project to create a
cool glowing Magic LED Cube, mainly made for light animation and basically could be explored for decoration of Electronics
Labs. [embed]https://youtu.be/A0OtHySzadk[/embed] Designed around the awesome RP2040 Microcontroller and Built with
a full of electronics…... Listed under: LED Projects
76. AVR Studio Simulator Introduction and Exercises LEARNING OBJECTIVES • get a brief introduction to most of the major
debugging features AVR Studio• read through a refresher on C programming and an introduction to I/O on AVR
microcontrollers• gain an appreciation of what the AVR Studio simulator is and what it's good…... Listed under: Sound - Audio
Projects
77. Using the AVRISP Programmer Introduction The AVRISP looks just like the JTAGICE, except it's a bit smaller and it has a 6-pin
connector on the end of the cable instead of the 10-pin connector on the JTAGICE. The AVRISP programmer does not have
the advanced debugging features of the…... Listed under: Microcontroller Programmer Projects
78. Prototype Board for Atmel Mega644 Introduction This page describes a prototype board for the Atmel Mega644 or Mega32
(PDIP) MCU. It includes a power supply, crystal clock, and generous bypass capacitors. A six-pin header allows flash memory
programming from an STK500 or AVRISPmkII. All port pins are brought out to…... Listed under: Development Board - Kits
Projects
79. Getting Started with TinyOS and nesC This lesson introduces the basic concepts of TinyOS and the nesC language in which
the system is written. It includes a quick overview of the nesC language concepts and syntax to help you get started with
programming in this environment. Introduction The TinyOS system, libraries,…... Listed under: Microcontroller Programmer
Projects
80. ECEN1400 Final Project- Sensor Spy Ball This is the final project for ECEN1400: Introduction to Digital and Analog with
Professor Alex Fosidck at University of Colorado at Boulder (Spring 2017). The goal of this project was to make a ball full of
sensors which could detect changes in its environment and…... Listed under: Sensor - Transducer - Detector Projects
81. LINE FOLLOWING AND OBSTACLE AVOIDING CAR 1.1 Introduction Line following car is a system that traces black lines on
white surfaces. There arevarious sensing methods available to sense these lines. The choice of these schemesdepends upon
sensing accuracy and required flexibility. In my project, I have used 6 TxLEDs and 6…... Listed under: Car Projects
82. Summer 2017 Altium Designer 17 Research This past summer I had the opportunity to work for computer science PhD
candidate Ryo Suzuki under the guidance of Tom Yeh of the computer science department. My task was developing printed
circuit boards for experiments for human computer interaction (HCI). The goal was to create…... Listed under: Other Projects
83. BUILDING KILOBOTS AND REVISING KILOBOT DESIGN FOR IMPROVING THE OPTICAL RESPONSE I would first like to
acknowledge my adviser, Dr. Yanjun Yan, for her patience, kindness, and mostof all her assistance in completing this thesis. I
would like to thank Dr. Martin Tanaka, Dr. PeterTay, and Dr. Paul Yanik for serving on my thesis committee. ABSTRACT…...
Listed under: Other Projects
84. A Simplified Secure Programming Platform for Internet of Things Devices INTRODUCTION The Internet of Things (IoT)
devices have become very popular in various critical and non-critical usage fields. Many people have started to use IoT
devices realizing their benefits in their lives and scientific research [MSPC12, CGOF13].Because of the popularity of IoT
devices, developers gravitate…... Listed under: Internet - Ethernet - LAN Projects
85. SMILab develops new low-cost strain sensor Researchers from the Smart Management of Infrastructure Laboratory (SMILab),
located in the Center for Advanced Research Computing, have developed a new strain sensor as a part of the Low-Cost
Efficient Wireless Intelligent Sensors (LEWIS) project. The new sensor, called the LEWIS-S, is easy to use, wireless, and…...
Listed under: Development Board - Kits Projects
86. Microcontroller Survivability in Space Conditions Introduction The Utah State University (USU) Materials Physics Group (MPG)
is interested in the performanceof Commercial Off the Shelf (COTS) microcontrollers in space conditions. Microcontrollers are
commonlyused on CubeSats, small relatively inexpensive satellites that are flown in Low Earth Orbit (LEO) ataltitudes of ~160
km-2000…... Listed under: Other Projects
87. Wireless Sensor Network for Energy and Environmental Monitoring: Helping Old Buildings Go Green I. Introduction Today,
the rising cost of energy and social trend of “going green” has put increasing pressure on commercial property owners to
improve the efficiency of their investments. There is good reason for this, too. In the State of California, office buildings
represent the…... Listed under: Internet - Ethernet - LAN Projects

88. Pololu USB AVR Programmer User’s Guide Overview The Pololu USB AVR programmer [http://www.pololu.com/product/1300]
is a programmer for Atmel’s AVRmicrocontrollers and controller boards based on these MCUs, such as Pololu Orangutan
robot controllers[http://www.pololu.com/category/8/robot-controllers] and the 3pi robot
[http://www.pololu.com/product/975]. The programmer emulates an STK500 on a virtual serial port, making it compatible
with…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
89. CC2420 Radio Introduction The Chipcon (now owned by Texas Instruments) CC2420 is a commercial radio chip that complies
with the ZigBee wireless standard. We have CC2420DBK development kits available for your project. Each development kit
comes with 2 development boards (2 radios). Each development board has a Chipcon CC2420…... Listed under: Radio Projects
90. NeoPixel Reactive Table https://youtu.be/46i9tALT3e8 https://youtu.be/HdIC7mgrhPU https://youtu.be/AC4vsxmy08Y
https://youtu.be/51IoAr7NIaY Welcome to my version of the LED reactive table! I was inspired by previous work using
discrete LEDs, such as this one, but I figured it would be easier and more fun to use NeoPixels -- programmable RGB LEDs
that can be set to…... Listed under: LED Projects
91. Multiple ATtiny85 or 13A Programmer Program 6 ATtiny85/13A at the same time with this custom programmer board.
Description Watch the video for a better tutorial. https://youtu.be/3tJi0zzWZtM Attiny MCUs are very popular as it is quite
easy to program them and using them instead of the atmega328 chip can reduce the…... Listed under: Microcontroller
Programmer Projects
92. I2C Blynk Car With Attiny85 and M5StickC This project shows you how to build your own I2C DC motor drive using a
DigiSpark Attiny85 plus Arduino motor shield. To test its operation, I made a small RC car which used an M5StickC &
connected to Blynk App. to communicate with this drive via the…... Listed under: Car Projects
93. AVR Atmega8 Microcontroller Architecture & Its Applications The abbreviation of AVR Microcontroller is “Advanced Virtual
RISC” and MCU is the short term of the Microcontroller. A Microcontroller is a tiny computer on a single chip and it is also
termed as a control device. Similar to a computer, the Microcontroller is made with a…... Listed under: Other Projects
94. Types and Applications of ATMEL Microcontroller Programming in Embedded Systems Atmel Microcontroller Programming
Atmel Microcontroller Programming – A microcontroller is actually a small and typically inexpensive computer. And you can
use it one to perform necessary calculations and conclusions in the uncomplicated hardware framework. Such as, the LED
panels generally present in subways can easily implement…... Listed under: Microcontroller Programmer Projects
95. ATmega versus STM32 – Which Microcontroller is Best for Your Application This article compares the ATmega and STM32
microcontrollers so that you can choose the best one for your own tech product, by considering overall cost and system cost,
as well as the upward migration path. Comparing ATmega and STM32 microcontrollers is a bit like comparing…... Listed
under: Other Projects
96. Getting Started with C Programming for the ATMEL AVR Microcontrollers Introduction This tutorial provides information on
the tool and the basic steps for programming the Atmel AVR microcontrollers using C. It is aimed at people who are new to
this family of microcontrollers. The Atmel STK500 development board and the ATmega16 chip are used in…... Listed under:
97. Atmel Studio 7 Latest Version for Windows & MacOS Atmel Studio was developed to help them build and debug
microcontroller applications. It comes as a platform for integrated creation that uses the shell of Microsoft Visual Studio. This
software manages programs written in C/C++ and even in the language of assembly effectively. I know that as a former…...
98. ATMEL USB PROGRAMMER CIRCUIT ZIF SOCKET USBASP ATMEGA8 Atmel USB programmer shared by more ö “Atmel AVR
USB programmer” circuit designed by the advanced ZIF socket version. Source: usbasp – USB programmer for Atmel AVR
controllers http://www.fischl.de/usbasp/ As long as the 8-pin pinout fit, 20-pin, 28-pin, 40-pin... Electronics Projects, Atmel
USB Programmer Circuit ZIF Socket…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
99. Types of AVR Microcontroller – Atmega32 & ATmega8 ATmega32 – 8 Bit AVR Microcontroller The AVR microcontrollers are based on the advanced
RISC architecture. ATmega32 is a low power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. AVR can execute 1 million
instructions per second if cycle frequency is 1MHz. Key…... Listed under: Other Projects

100. ATMEL AVR Tutorial 2 : How to access Input / Output Ports ? Overview You cannot imagine to use microcontroller without
using any of its i/o pins. Finally its all about : taking input , processing it and generating output ! Thus i/o registers and their
correct settings is indispensable part while learning to program any uC. We will…... Listed under: Other Projects
101. Programming AVR Microcontrollers with Atmel Studio 7 Inexpensive microcontrollers have seen a resurgence thanks to the
internet of things (IoT) and wearable devices. These end-uses depend on parts that have low costs rather than record-
breaking speed. Because of this, devices like the Atmel AVR series have enjoyed decades of popularity. Any software…... Listed
under: Microcontroller Programmer Projects
102. Classic Atmel ATtiny85-20PU Stop Light The Classic ATtin85-20PU is a very simple project that is also very fun to make. It
really is perfect for a parent/child combo because it's quick! Builds in minutes. But it does teach several electronic hobbyist
skills.There is a story behind my decision to become…... Listed under: LED Projects
103. ATTiny85 Game Timer – Get Rid of That Old Hourglass! What did I make? = This is a little project that uses ATTiny85 to make
a simple "game timer", intended to be used with board games that demand timed turns, like "Rummikub" or "Scrabble".
Never wait for all that sand getting down for the next…... Listed under: Clock Projects
104. LED Cube 3x3x3 With ATMEGA8 An interesting project and already much discussed in the forums and also in videos.Although
it appears complex,it is a simple idea and fun very purpose. Mounting material: - 27 LEDs matte- Microprocessor ATmega8-
Electrolytic capacitor 47UF 16V- Veroboard- Small wood board at the minimum 10x10cm-…... Listed under: LED Projects
105. Obsatcle Avoidance Vehicle Using ATmega328P Microcontroller (Arduino) Obstacle Avoidance Vehicle capable of detecting
objects, scanning the area and navigating through the less obstructed path. Step 1: Materials Needed Hardware Arduino
UNO based on ATmega328 microcontrollerDYP-ME007 ultrasonic sensorServomotorL298N Dual H-Bridge Motor driverPower
Supply - i used LiPo 2s 4000 mAH2x DC motors with…... Listed under: Other Projects
106. HackerBox 0044: PCB 123 Greetings to HackerBox Hackers around the world! HackerBox 0044 brings us PCB Design, AVR
Device Programming, Serial RGB LED Applications, Pro ESP32 WiFi OLED Development, and much more. This Instructable
contains information for getting started with HackerBox 0044, which can be purchased here while supplies last. If…... Listed
107. Updated Guide on How to Program an Attiny13a or 13 With the Arduino IDE The ATtiny13 series chips are extremely cheap
and useful chips for small projects that don't need a full Arduino, but due to very outdated tutorials and a lack of
information, it took me the better part of a day to figure out how to program…... Listed under: Microcontroller Programmer
Projects
108. ATtiny Programming With Arduino After this Instructable you should be able to program an A Ttiny85/45 with an arduino. It
may sound complex but it really isn't. After doing some research I could not find to much info on how this could be done. I
however did find https://www.instructables.com/id/Program-an-ATtiny-with-Arduino/. This Instructable…... Listed under:
109. ATtiny85 Interrupt Barebones Example This example code and simple wiring demonstrated how to setup an AVR ATtiny85 processor to react to
external interrupts. Whenever the voltage changes on the chosen input pin (pin 6 / PB1), it executes the interrupt service routine (ISR), checks the
current voltage, and sets…... Listed under: LED Projects

110. Ghetto Development Environment A while back, I posted up a quick and dirty "el cheapo" method of getting started
programming the Atmel AVR series chips: Ghetto Programmer (version 1.0) Since then, I've vamped, re-vamped, and
otherwise improved my setup. Thought it'd be nice to document it. The goal was…... Listed under: Development Board - Kits
Projects
111. How to Make a Cheap Attiny Arduino Board Well most of time i get troubled when i need Arduino in some projects where i
need few I/O pinsWell thanks to Arduino-Tiny platform Arduino program can be burned into the Avr-tiny Series like Attiny
85/45 Arduino-Tiny is an open source set of ATtiny "cores"…... Listed under: Development Board - Kits Projects
112. Programming the ATtiny This is a tutorial for programming the ATtiny chip. This tutorial will be more in depth than most. I
will give you every step and tell you the things nobody told me when I first started programming ATtiny. Things You'll Need -
Arduino Uno( Can…... Listed under: Microcontroller Programmer Projects
113. ATtiny Programmer Using Arduino ISP For relatively small (less number of pins than ATmega328) projects, ATtiny series,
ATtiny45 or Attiny85 are good choice in terms of its physical size (8-DIP or 8-SOIC) and low power consumption. There are
many ways to program it. One of the popular device is USBtinyISP and DASA. Both…... Listed under: Microcontroller
Programmer Projects
114. ATtiny85 Mini RGB Mood Light! I have seen RGB mood lights using Arduino, PIC, and larger AVR chips, but never one with
the ATtiny85. That's why I decided to make one. This mood light is super simple to make and all the parts can be purchased
online for about $5.00…... Listed under: LED Projects
115. Wave JT – Larson Scanner With Joule Thief I love LED chasers. A bunch of LEDs neatly turning on and off on a precise timing -
lights running one way, then the other way… It's relaxing, soothing, and hypnotic. There are so many LED
chaser/scanner/sequencer circuits out there, some are made with discreet…... Listed under: LED Projects
116. 3 Easy ATTiny Holiday Gifts Every year the holiday season rolls around and I get stuck on what to give for my friends and
family. People always say that it's better to make the gift yourself than buy it at a store so this year I did just that. The…...
Listed under: Radio Projects
117. ATtiny85 Mini RGB Mood Light! I have seen RGB mood lights using Arduino, PIC, and larger AVR chips, but never one with
the ATtiny85. That's why I decided to make one. This mood light is super simple to make and all the parts can be purchased
online for about $5.00…... Listed under: Other Projects
118. DIY Atmel Microcontroller Development Board In this Instructables I am going to show you how to make a very useful
development board for your favourite Atmel microcontroller that will help you save up to the third of the space on your
breadboard and let you move your microcontroller around without…... Listed under: Other Projects
119. Car Datta Logger Using OBD II Protocol (atmega 2560+ SD Card + Lcd 16×2) Ok first of all this was a final project for my
microprocessor course in my University, and its intended to clarify and guide to someone has a similar project or just want to
do it and learn , since when i was doing this project…... Listed under: LCD Projects
120. AVR Projects Collection | 16 ATmega MCU Projects AVR is a family of microcontrollers developed by Atmel beginning in 1996. These are modified
Harvard architecture 8-bit RISC single-chip microcontrollers. ATmega series are one of the types of AVR microcontrollers with features like 4–256 KB

program memory, 28–100-pin package, extended instruction set, and extensive peripheral set. These special features help students, hobbyists and
engineers make innovative…... Listed under: Other Projects
121. ATMEGA328P Microcontroller ATmega328P is one of the high performances AVR technology microcontroller with a large
number of pins and features. It is designed by 8-bit CMOS technology and RSIC CPU which enhance its performance and its
power efficiency get improved by auto sleeps and internal temperature sensor. This ATmega328P IC…... Listed under: Other
Projects
122. Rotary Encoder Interfacing with ATmega8 Microcontroller In this tutorial we are going to interface a rotary encoder with
ATmega8 microcontroller. ATmega8 is atmel's microcontroller series designed for embedded applications. Rotary encoder is
used to know the position of movement and angular movement of a motor or axis. It’s a three terminal device usually,…...
123. UART Communication Between Two ATmega8 Microcontrollers In this tutorial we are going to establish a serial
communication between two ATMEGA8 microcontrollers. The communication established here is UART (Universal
Asynchronous Receiver Transmitter) type. By this serial communication data can be shared between two microcontrollers,
which is required in various embedded systems. Components Required Hardware: ATMEGA8 (2 pieces), power supply…...
124. Interfacing 16×2 LCD with Atmega16 AVR Microcontroller in 4-Bit Mode Display is the necessary part of any machine
whether it is any home appliance or industrial machines. Display not only shows the control options to operate the machine
but also shows the status and output of the task performed by that machine. There are many…... Listed under: LCD Projects
125. Interfacing Servo Motor with AVR Microcontroller Atmega16 Servo Motors are widely used where precise control is required
such as robots, Automated Machineries, robotic arm etc. However, the scope of the servo motor is not limited to this much
and can be used in many applications. To know more about the basics, theory and…... Listed under: Motor Projects
126. How to Program AVR Microcontroller Atmega16 Using USBASP programmer and Atmel Studio 7.0 There are several ways to
program AVR microcontrollers. We are programming it with USBASP v2.0 serial programmer. For demonstration we will use
ATmega16 Microcontroller and Atmel Studio. We will test the programmer with a blink sketch. Below are the steps to burn
the code into…... Listed under: Microcontroller Programmer Projects
127. Interfacing Stepper Motor with AVR Microcontroller Atmega16 Stepper Motors are DC brushless motors which can rotate
from 00 to 3600 in steps. Stepper motor uses electronic signals to rotate the motor in steps and each signal rotates the shaft
in fixed increment (one step). The rotation angel is controlled by applying certain sequence of…... Listed under: Motor
Projects
128. How to use ADC in AVR Microcontroller ATmega16 One common feature that is used in almost every embedded application
is the ADC module (Analog to Digital Converter). These Analog to digital Converters can read voltage from analog sensors
like Temperature sensor, Tilt sensor, Current sensor, Flex sensor etc. In this tutorial we will learn What is…... Listed under:
Other Projects
129. Line Follower Robot using AVR Microcontroller ATmega16 Here we will be building yet another project with AVR Atmega16
Microcontroller. If you are new to AVR microcontrollers then you can refer to previous AVR projects and tutorials. Building a
robot is always a thrill for all electronics hobbyists. And this thrill can be maximized if…... Listed under: Robotics - Automation
Projects
130. Digital Wall Clock on PCB using AVR Microcontroller Atmega16 and DS3231 RTC Every digital clock has a crystal inside it to
keep track of time. This crystal is not only present in the clock but also present in all computing real-time systems. This crystal
generates clock pulses, which is needed for timing calculations. Although there are some other ways to…... Listed under:
Clock Projects
131. Interfacing ESP8266 NodeMCU with Atmega16 Microcontroller to Send an Email Atmega16 is a low cost 8 bit microcontroller
and comes with more number of GPIO’s than its previous version of microcontrollers. It has all the commonly used
communication protocols like UART, USART, SPI and I2C. It has wide applications in robotics, automobile and automation
industries…... Listed under: Other Projects
132. Understanding Pulse width Modulation (PWM) in Atmega16/32 AVR Microcontrollers Pulse Width Modulation (PWM) is a
powerful technique where width of the pulse is changed by keeping the frequency constant. The technique is used in many
control systems today. The application of PWM is not limited and it is used in wide range of applications such…... Listed
under: Motor Projects
133. How to Use Hall Sensor with AVR Microcontroller ATmega16 Hall sensors works on the principle of Hall Effect proposed by
Edwin Hall in 1869. The statement proposed says, “The Hall effect is the production of a voltage difference (the Hall voltage)

across an electrical conductor, transverse to an electric current in the conductor and to an…... Listed under: Sensor - Transducer - Detector Projects
134. Interfacing DC Motor with AVR Microcontroller Atmega16 DC motors are the most widely used motors. These motors can be
found almost everywhere from small projects to advanced robotics. We previously interfaced DC Motor with many other
microcontrollers like Arduino, Raspberry pi and used it in many robotic projects. Today we learn to control DC motor with
AVR…... Listed under: Motor Projects
135. Fingerprint Based Biometric Attendance System using Atmega32 Microcontroller According to researchers from Pen state
University, humans are more likely to trust machines over people, which is likely evident from us revealing our ATM pin to a
machine so easily. Today, in the world where AI, Machine learning, Chat bots, Smart Speakers, Robots etc are actively
progressing, this…... Listed under: Other Projects
136. GPS module (uBlox Neo 6M) Interfacing with AVR Microcontroller Atmega16/32 GPS modules are widely used in electronics
applications to track the location based on longitude and latitude coordinates. Vehicle tracking system, GPS Clock, Accident
Detection Alert System, traffic navigation, surveillance system etc. are few of the examples where GPS functionality is
essential. GPS provides Altitude, Latitude, Longitude, UTC time and many…... Listed under: GPS Based Projects
137. Understanding Fuse Bits in ATmega328P to Enhance Arduino Programming Efficiency In this tutorial, we are going to talk
about fuses. Back when I was in college and learning about all the cool things in electronics, I heard the term fuse in AVR for
the first time, my initial thought on the topic was, oh! there is…... Listed under: Microcontroller Programmer Projects
138. Cardboard Dragon Robot Who doesn't love dragons? I know I do. I wanted to challenge myself with this project and build it
all out of cardboard practicing some techniques I recently learned, and control it using a small thumbstick controller.
Supplies: For this build, you will need: -3…... Listed under: Robotics - Automation Projects
139. Battery Powered Simple Waste Auditing Data Logger I wanted a way to keep track of how much waste I was generating
just to be more environmentally conscious. So I created this project as an automated way to help keep track of waste
accumulation through fullness measurements while also taking pictures of the…... Listed under: Battery Projects
140. Mandelbrot Set on Pi Pico / ILI9341 Mandelbrot Set is IMHO the most famous fractal. Read here for additional info:
https://en.wikipedia.org/wiki/Mandelbrot_set This project was inspired by https://hackaday.io/project/177884-mandelbrot-
on-p... I reused most of the original code, but decided to implement it with 2.8" ILI9341 SPI tft using Pico micropython driver
from https://github.com/jeffmer/micropython-ili9341. This is my first project with…... Listed under: Other Projects
141. Connecting to Microcontroller With Pyserial Library – Python Hi, In this instructable, we'll see how to use the Pyserial library
in Python in order to make a serial connection via a COM Port (in our example COM3) and receive the temperature and
humidity values from an MSP430 Microcontroller which is programmed to obtain…... Listed under: Other Projects
142. Open Source Ventilator Alternative Access to medical devices is unequal across the globe, and the COVID-19 pandemic has
underscored this fact. During the pandemic the global shortage of ventilators has been especially notable. Access to
mechanical ventilation in Low and Middle Income Countries is inadequate. South Sudan, for example,…... Listed under:
Medical - Health based Projects
143. Automatic Water Barrel Filler A relative asked me if I could create something that automates refilling a water barrel used for
watering a small garden greenhouse. They didn't want to plug in a pump every few hours only to have turn it off again ten
minutes later when it…... Listed under: Home Automation Projects
144. Decoder / Electronic Quiz Game 2.0 Some time ago I presented the Electronic Quiz I made when I was a kid. It can be used to
solve quiz sheets. The big drawback is, that each number is hard-wired to one letter so there are 26 fix combinations. Those
are fast to memorise, even more…... Listed under: Game - Entertainment Projects

145. Wheelchair Pride Project The Wheelchair Pride Project is designed to allow wheelchair users to feel confident and
empowered in their chairs by creating an avenue for self-expression within the chair itself. Oftentimes wheelchairs are cold
and industrial looking because they are designed for functionality, but when a wheelchair…... Listed under: Home Automation
Projects
146. Network Rivalry: a Low-Latency Game for the BBC Micro:bit In this tutorial, I will explain how to implement a basic multiplayer
game on the BBC micro:bit with the following features: A simple interfaceLow-latency between button presses and screen
updatesA flexible number of participantsEasy control over the game using a master remote ("root") device The…... Listed
under: Game - Entertainment Projects
147. How to Run Servo Motors Using Moto:bit With Micro:bit One way to extend the functionality of the micro:bit is to use a
board called moto:bit by SparkFun Electronics (approximately $15-20). It looks complicated and has many features, but it isn’t
hard to run servo motors from it. Moto:bit allows you to run more powerful motors than…... Listed under: Motor Projects
148. Paper Pocket Pets Paper Pocket Pets (PPP) is a kit designed to create interactive modular and wearable toys. It encourages
children's movement and sociality thanks to the reactions of the pet and allows children to build their own representative pet
and also to change it over time if…... Listed under: Other Projects
149. Parallel Apps on an ESP32 Using Toit Platform for IoT With the Toit platform, developers can treat an ESP32 as a regular
computer, installing apps just as easy as on a computer or a phone. Using the high-level language Toit, it is easy to
implement functionality and applications while the Toit platform ensures that the…... Listed under: Other Projects
150. Micro:bit Controlled Tic Tac Toe Game With the addition of micro:bit to Tinkercad's Circuits editor, it is now possible to create
circuits with other Tinkercad Circuits components and to simulate the operation of the system by controlling these circuits via
micro: bit. In light of this new feature, we have prepared…... Listed under: Game - Entertainment Projects
151. 10 Channel Wi-Fi Switch for Smart Home This device can help you automate your home, backyard, or whatever you want.
Step 1: Gather the Components To build this device, you'll need: ESP8266 x1;4-stage ripple (binary) counter (I can suggest
SN74LS93N) x1;14-stage ripple counter (CD4020BE is the best choice) x1;Latches (SN74LS75) x6. Since…... Listed under:
Internet - Ethernet - LAN Projects
152. Firefly Pickle Jar With Microbit and Neopixels A motion sensitive firefly-filled pickle-jar that gets brighter when you move it,
and then settles down to just twinkle a bit when its still. This project was inspired by a workshop led by Lila Finch and the
great folks doing tinkering / creative learning at…... Listed under: Other Projects
153. VFD Display for the TI83+ Calculator This project builds upon the PIC/TI83+ interface developed by ThomasHenry (see Nuts
& Volts August 2013 – A Mathematics Engine for Microcontrollers). Acknowledgment, appreciation, and kudos to him for
writing the TI-library for Great Cow Basic that made this project possible. When I recently re-discovered…... Listed under:
Calculator Projects
154. Spin Bike Controller SmartSpin2K is an open hardware and software DIY module that converts BLE signals from a cycling APP
(like Zwift, FulGaz, RGT, Sufferfest, etc.) and uses the information they broadcast to increase and decrease resistance on a spin
bike by rotating the resistance knob with a stepper…... Listed under: How To - DIY - Projects
155. BBC Micro:bit + WiFi + Phone Notifications https://youtu.be/8QtW7gWWhOE In this project we demonstrate BBC micro:bit how to connect it to WiFi
and send a notification to a phone without writing a single line of code. The micro:bit comes with a microphone, among the other features. We are

going to use it to detect loud sound e.g.…... Listed under: Internet - Ethernet - LAN Projects
156. Arbitrary Wave Generator With the Raspberry Pi Pico Just two weeks ago, the pico, a new microcontroller, the pico, was
released by the Raspberry Pi Foundation, well known for the incredibly successful series of Raspberry Pi single-board
computers. The new microcontroller uses a brand new chip, designed in-house, the RP2040. It has two 32-bit…... Listed under:
Other Projects
157. Smart Home With Multiple NodeMCU ESP8266 Network With Blynk In this IoT project, I have shown how to make IoT-based
Smart Home Automation using Multiple NodeMCU ESP8266 network to control all the home appliances from
the pushbuttons & Blynk App. If the internet is not available, then you can control the home appliances from manual
switches. During the article,…... Listed under: Other Projects
158. Dual Cores & Interrupts on Pi Pico https://youtu.be/OvF_Doo27LM The new Raspberry Pi Pico offers Dual Cores and
Interrupts if you use MicroPython. I thought I would give it a go and try explain some of the pitfalls to avoid. This project
keeps the action running on the two cores very simple, so…... Listed under: Circuits
159. [Gamer Assist] Haptic Feedback System for Games Using Esp8266 So, in this video we’ll be seeing how to build this haptic
feedback device and the ambient light system which reacts to the player's health value inside a PC game! For that we’ll be
using the ESP-NOW protocol, about which we learnt in the previous…... Listed under: Game - Entertainment Projects
160. Illuminated Cubes This project is a follow up of the Illuminated Presents project that I posted earlier. My wife really liked the
Illuminated Presents but kept them as Cubes and did not put a bow around it to turn them into presents. Because of this
success I created a…... Listed under: Battery Projects
161. Always Know Where Home Is At Introduction: I built this project as a birthday present for my oldest daughter. She had
recently moved far from home and I wanted her to know her family was still there for her. I chose a Lord of the Rings theme
and aesthetic because she…... Listed under: Home Automation Projects
162. PID Controlled Thermostat Using ESP32 (Applied to a Rancilio Silvia Coffee Machine) WarningThe Rancilio Silvia machine runs
on high voltage. Any modification to it might be fatal to you or your machine, you act at your own risk and responsible for
your modification. Any modification to the machine might void the manufacturer warranty. Make sure to disconnect…...
Listed under: Motor Projects
163. Totally Useless Coffee Dispenser… So I have yet again over-engineered a task, this time, a freeze-dried coffee dispenser. Why
you ask, well the obvious first, it’s super fun and second, it’s the best way to learn new skills. I’m a real noob when it comes to
the inner workings…... Listed under: Motor Projects
164. Frequency Counter With Variable Gate Time Frequency counter (reciprocal) Gate time selectable from 0.1 second up to 60
seconds Frequency range from 0.1 Hz up to 10 MHz (tested) Input 3.3V and 5V safe Uses a STM32F103C8 (Blue Pill) and 16x4
LCD code is available on gitlab: https://gitlab.com/WilkoL/frequency-counter-with-v... Supplies: STM32F103C8 (Blue…... Listed
165. Serial Monitor With ILI9341 and BluePill Serial (ascii) monitor with 9 lines of 28 char.Baudrate from 2400 up to 256000 baud.
Digital 3.3V or 5V input. Powered by a single Lithium-Ion battery. (3.7V nominal). Supplies: ILI9341 display (here a parallel
version is used) BluePill (or other board with a STM32F103C8) 74HC14…... Listed under: Battery Projects

166. Makey Makey Winter/Holiday Jukebox As a second year STEM teacher, I've been using the Makey Makey kits with my 4th,
5th, and 6th graders to explore circuitry, electricity, and to just have some fun! Students have had their choice of projects,
ranging from interactive displays to musical instruments using…... Listed under: Other Projects
167. MODAS: Magnetic Open Door Alert System Hey fellow DIY'ers. Have you ever found your house door open after returning
from a long trip? Me neither. But it is always good to have a safety system in our houses. I'm not talking about the old school
projects like a laser trip wire,…... Listed under: Security - Safety Projects
168. Set @Holiday = Valentines_Day This Instructable can be modified for any major holiday, however my students wanted to
focus on something they could do for Valentine's Day. In this design, students' hands are the conductive material that
complete the circuit when they "high-five" the two halves of the heart.…... Listed under: Circuits
169. WaveShare Motor/Servo Driver With Micro:bit This Instructable will show you how to use a WaveShare motor/servo board
with a micro:bit to power multiple servo motors. This board will make it possible to run more powerful servo motors than the
micro servo motor that you can run directly from the micro:bit.…... Listed under: Motor Projects
170. Bluetooth On “Air” Lapel Pin I was working on an unrelated project that utilizes Bluetooth, I had to test the communication so
I built one of the Arduino test circuits. The light contains all of the electronics, microcontroller and battery which can be
recharged VIA USB. It uses really strong…... Listed under: Other Projects
171. Hello Train! ATtiny 1614 For my Fab Academy class I have to create a board with a microcontroller, a button and a LED. I will
use Eagle to create it. Step 1: ATtiny 1614 I will use the ATtiny 1614, so I will use the reference of the echo…... Listed under:
LED Projects
172. MicroPython Program:Update Coronavirus Disease(COVID-19) Data in Real Time In the past few weeks, the number of
confirmed cases of coronavirus disease (COVID 19) worldwide has exceeded 100,000, and the world health organization
(WHO) has declared the new coronavirus pneumonia outbreak to be a global pandemic. I was very worried about this
outbreak, and…... Listed under: Arduino Programmer Projects
173. GPS Monitoring With OLED Display Project Hello everyone, in this quick article I will share with you my project :ATGM332D
GPS module with SAMD21J18 Microcontroller and SSD1306 OLED 128*64 display, I built a special PCB for it on Eagle
Autodesk, and program it using Atmel studio 7.0 and ASF4 so in…... Listed under: GPS Based Projects
174. MicroPython PCF8591 DACtest I bought this book to improve my Micropython-skills: MicroPython for ESP8266 Development
Workshop by Agus Kurniawan. This book is a very good start, the I2C project uses a PCF8591 module. But no DAC
programming example so I had to figure that out by myself :-)…... Listed under: Other Projects
175. AI With Grove Zero and Codecraft (Scratch 3.0) In this article we're going to build three projects utilizing AI functions of
Codecraft, a graphical programming environment based on Scratch 3.0. Codecraft is developed and maintained by TinkerGen
education and is free to use. AI and it's subset, machine learning, has become an integral…... Listed under: Other Projects
176. Dino Jump Run Cactus Because of the coronavirus epidemic, a friend of mine had to be quarantined for 14 days. He
complained to me that the quarantine time was too long and it was boring. He likes to play dino jumping cactus. This is a
game that can be…... Listed under: Internet - Ethernet - LAN Projects

177. Lora Gateway Based on MicroPython ESP32 Lora has been very popular in recent years. The wireless communication module
using this technology is usually cheap (using free spectrum), small in size, energy-efficient and has a long communication
distance, and is mainly used for mutual communication between IoT terminals or data exchange with…... Listed under:
178. Make Your Own Oscilloscope(Mini DSO) With STC MCU Easily This is a simple oscilloscope made with STC MCU. You can use
this Mini DSO to observe waveform. Time Interval: 100us-500ms Voltage Range: 0-30V Draw Mode: Vector or Dots. Step 1:
Watch the Video! https://youtu.be/c6gBv6Jcz7w In this video, I will show you how to assembly…... Listed under: Battery
Projects
179. Dual Colour Bar Graph With CircuitPython I saw this LED bar-graph on the Pimoroni site and thought it might be an
inexpensive and fun project while undertaking covid-19 lockdown. It contains 24 LEDS, a red and a green, in each of its 12
segments, so in theory you should be able…... Listed under: Other Projects
180. Micro:bit Zip Tile Introduction Before I continue my serie of MU vision sensor instructables for the Micro:bit, I need to make
this instructable for the Kitronik Zip Tile, since I am going to use it. The Kitronik Zip Tile, I will just call it Zip from now on,
is…... Listed under: Sensor - Transducer - Detector Projects
181. Microbit Capacitance Meter What is a capacitor? A device that stores electrical charge which in its basic form consists of two
conducting plates separated by a dielectric. In addition to the basic parallel plate several other forms of construction exist an
example being that the plates in the…... Listed under: Metering - Instrument Projects
182. BBQ Temperature & Meat Sensor on ESP8266 With Display In this Instructable I will show you how to make your own version
of a BBQ tool that measures the current temperature in your barbecue and turns on a fan to light it up if needed. Additional
to this there is also a meat core…... Listed under: Temperature Measurement Projects
183. Upgrade DIY Mini DSO to a Real Oscilloscope With Awesome Features Last time I shared how to make a Mini DSO with MCU.
To know how to built it step by step, please refer to my previous instructable: https://www.instructables.com/id/Make-Your-
Own-Osc... Since many people are interested in this project, I spent some time upgrading it overall. After upgrading,…...
Listed under: How To - DIY - Projects
184. ESP32-CAM Video Surveillance Smart Camera Description This project is a development of our ESP32-CAM Video
Surveillance Robot project. Eventually we got a video surveillance pan & tilt camera that can be controlled with an iPhone
through Internet Step 1: Parts List: ESP32-CAM x1 FT232RL FTDI Mini USB x1 - for…... Listed under: Security - Safety Projects
185. Coronavirus EXTER-MI-NATION With Micro:bit and Daleks https://youtu.be/06Um8RRdghc This is a second project in series
on coronavirus protection from TinkerGen. You can find the first article here. We firmly believe that with humanity's collective
efforts, current epidemic will soon come to an end. But even after COVID-19 has passed we should remain vigilant…... Listed
186. Interactive Minecraft Do Not Enter Sword/Sign (ESP32-CAM) There are really several reasons why this project came into
existence: 1. As an author of cooperative multitasking library TaskScheduler I was always curious how to combine the benefits
of cooperative multitasking with the benefits of pre-emptive one. There are benefits to both and both have shortcomings.…...
187. Launch-Ready SSTV CubeSat Satellites are man-made instruments that collect information and data from space. Humans
have pioneered space technology over the years and space technology is more accessible than ever. Earlier Satellites used to
be very complicated and expensive but Now space technology is more accessible and affordable…... Listed under: Other
Projects
188. Micro:bit MU Vision Sensor and Zip Tile Combined So in this project we are going to combine the MU vision sensor with a Kitronik Zip Tile. We will
use the MU vision sensor to recognise colours and get the Zip Tile to show it to us. We are going to use some of…... Listed under: Sensor - Transducer

- Detector Projects
189. Mini Oscilloscope This is an Instructable about a mini oscilloscope I made, it isn't anywhere near as capable as a real (digital)
oscilloscope (such as my Rigol) but I think it is nice to have. Even more important, I enjoy making things, even when they
have no…... Listed under: Other Projects
190. Make It So! Star Trek TNG Mini Engineering Computer Overview I grew up watching Star Trek: The Next Generation. I've
always wanted to build a Star Trek themed device, so I finally got around to remixing one of my old projects to make a Star
Trek Display Terminal. The terminal provides the following information:…... Listed under: Other Projects
191. Dual Trace Oscilloscope When I build my previous mini oscilloscope I wanted to see how well I could make my smallest ARM
microcontroller a STM32F030 (F030) perform, and it did a nice job. In one of the comments it was suggested that a "Blue Pill"
with a STM32F103…... Listed under: Sensor - Transducer - Detector Projects
192. DIY Smart Doorbell: Code, Setup and HA Integration In this project, I will show you how you can transform your normal
doorbell into a smart one without changing any of the current functionalities or cut any wires. I will be using an ESP8266
board called Wemos D1 mini. New to ESP8266? Watch my Introduction…... Listed under: Sound - Audio Projects
193. Laser Game https://youtu.be/nRc_CEQqXQw "Star Trek", "The Terminator", "Star Wars" or "The Avengers" - in each of these
films technology was on a cosmic (literally) level. The heroes used laser weapons, which always fascinated me. I decided to
build a laser gun, but I would not use it to kill people or aliens,…... Listed under: Game - Entertainment Projects
194. WiFi Enabled Matrix Lamp Who does not want to have stunning lamp which can display animations and sync with other
lamps in the house? Right, nobody. That's why I made a custom RGB lamp. The lamp consists of 256 individually addressable
LED's and all of the LED's can be…... Listed under: LED Projects
195. Chain Reactions With Strawbees and Makey Makey Gamify your chain reaction by using a Strawbees grabber connected to
Makey Makey to start a timer in Scratch when you grab a conductive egg. Drop the egg on the Strawbees roller coaster track.
When the egg rolls into the egg drop, it stops the…... Listed under: Other Projects
196. GPS Cap Data Logger Here is a great weekend project, if you are into trekking or taking long bike rides, and need a GPS data
logger to keep track of all your treks/rides you taken... Once you have completed the build and downloaded the data from
the GPS module…... Listed under: GPS Based Projects
197. Origami 3D Beating Heart It is a 3D paper heart which starts Blinking (Glowing) when someone holds it. To surprise someone,
this gift is a perfect idea as it looks like a simple origami heart but it starts blinking just like a beating heart when someone
touches or holds…... Listed under: Other Projects
198. How to Make IoT Based Home Automation With NodeMCU Sensors Control Relay In this IoT based project, I have made
Home Automation with Blynk and NodeMCU control relay module with real-time feedback. In the Manual Mode, this relay
module can be controlled from Mobile or smartphone and, Manual switch. In Auto Mode, this smart relay also can…... Listed
under: Sensor - Transducer - Detector Projects
199. Tap Tap Rainbow – a 2 Player Quick Reaction Game 2 weeks ago my daughter had a genius idea to make a quick reaction
game with rainbow colors (she's a rainbow expert ). I instantly loved the idea and we started thinkering how we could
make it into a real game. The idea was.…... Listed under: Game - Entertainment Projects
200. Make a Dancing Robot Without 3d Printer and Arduino/#smartcreativity https://youtu.be/mrpztOozA2U Hello friends, in this
tutorial I will show you to how to make a dancing robot at home without 3D printer and without Arduino. This robot is able
to dance, auto balancing, music producing and walking. And the design of Robot is also looking…... Listed under: Robotics -
Automation Projects

201. Cat Repellent To start with, I do not hate cats but I love birds. In my garden we have some open cages where birds can enter
and leave as they please. They can find food and water there. Unfortunately sometimes a cat from the neighborhood enters
my…... Listed under: AVR ATmega Projects
202. Mushroom Climate Box Hi there! i have built a climate box to grow mushrooms. It can regulate both temperature and
humidity. The heating or cooling works with a peltier element. The air humidity is increased with an ultrasonic nebuliser. I
have built everything modular, so that you can…... Listed under: Other Projects
203. Pulse Generator When you need pulses of any sort, long, short and with variable frequency you can use one or two 555
timers. That works, is easy to set up and is cheap. But it also limited to a certain range in frequency and pulse length. If…...
204. UltraSonic Liquid Level Controller IntroductionAs you probably know, Iran has dry weather, and there is a lack of water in my
country. Sometimes, especially in the summer, it can be seen that the government cuts the water. So most of the apartments
have a water tank. There is a…... Listed under: Sensor - Transducer - Detector Projects
205. Using the Kitronik Inventor’s Kit With the Adafruit CLUE The Kitronik Inventor's Kit for the BBC micro:bit is a great
introduction to microcontrollers with electronics using a breadboard. This version of the kit is designed for use with the
inexpensive BBC micro:bit. The detailed tutorial book which comes with the kit includes MakeCode examples using Blocks
and JavaScript equivalent…... Listed under: Other Projects
206. BBC Micro:bit and Scratch – Interactive Steering Wheel & Driving Game One of my class assignments this week is to use the
BBC Micro:bit to interface with a Scratch program we've written. I thought that this was the perfect opportunity to use
my ThreadBoard to create an embedded system! My inspiration for the scratch program comes from vintage…... Listed under:
Game - Entertainment Projects
207. WiFi LED Switch IoT The main aim of this project is to come up with a functional WiFi switch that will help us operate via the
"Blynk" app from the Mobile app store. This Instructable is successfully tested with very basic knowledge of Electronics and I
would appreciate suggestions…... Listed under: LCD Projects
208. Click Brick Switch for Makey Makey This 3D printed switch will allow the user to turn a Makey Makey into a "finger slide" for a
"click" in gaming or could be right/left arrows to scroll through presentations. The addition of right and left terminal mounts
for the ground wire makes it…... Listed under: Other Projects
209. BOXOI – an Open Source Miniature 3D Zoetrope DIY Kit Project Background: In 2015, I started a kickstarter project of a
miniature 3D zoetrope DIY kit. The next year, I started the version 2 of said project by further simplifying the kit and reducing
its manufacturing cost. Sadly, both crowdfunding failed, but this is how the…... Listed under: How To - DIY - Projects
210. MQTT Swimming Pool Temperature Monitor This project is a companion to my other Home Automation projects Smart Data-
Logging Geyser Controller and Multi-purpose-Room-Lighting and Appliance Controller . It is a pool side mounted monitor
that measures the pool water temperature, ambient air temperature and barometric pressure. It then displays the pool water
temperature on…... Listed under: Temperature Measurement Projects
211. Clock Generator With Si5351 and Blue Pill Clock generator I recently build a pulse generator and it does its job well. It
produces pulses of variable length and at several frequencies. But the number of frequencies it can produce is limited and for
many jobs the length of a pulse is less…... Listed under: Clock Projects
212. Binary DVM Binary displays are very popular for clocks so it looked like there a gap waiting to be filled in the measurement
area with an instrument that displayed its results in a Binary format. As result I decided that a DVM would be a suitable
project…... Listed under: Metering - Instrument Projects
213. A Bluetooth ESP32 TFT + Touch Macro Keypad) Controlling your computer by using hotkeys and macros is a great way of
speeding up your workflow. Unfortunately a device dedicated to doing that (for example Elgato's Stream Deck) will cost you
about $120. That is why I designed FreeTouchDeck. FreeTouchDeck will cost you about…... Listed under: Other Projects

214. Hands-Free Cardboard Gumball Machine We made a Touch-Free Gumball Machine Using a micro:bit, a Crazy Circuits Bit
Board, a distance sensor, a servo, and cardboard. Making it and using it was a "BLAST"! ???? ???? When you place your hand
in the base of the rocket, a distance sensor…... Listed under: CNC - Printing Machines Projects
215. MIDI Handpan With 19 Tonefields on Upper and Down Side… Introduction This is a tutorial of my custom made MIDI
handpan with 19 volume sensitive tonefields, Plug'n Play USB capability, and a lot of easy to use parameters for adjusting the
pads for your individual needs. It's not a design award winning model but…... Listed under: Other Projects
216. SIMPLE QUADCOPTER ( HUBSAN X4 ) In this Instructable I will let you know the basic building block of a Quadcopter and
how to make it in a very simple way.Only thing you need is some skill on Soldering and few basic tools.I think it will give
opportunity to the new…... Listed under: Other Projects
217. Wakeup Light As I write this instructable it is mid winter on the Northern hemisphere and that means short days and long
nights. I am used to getting up at 06:00 and in the Summer the sun will be shining by then. In the Winter though, it…... Listed
under: Development Board - Kits Projects
218. DIY ESP8266 ESP-12 Socket – Snap Fit, Breadboard Friendly, No Soldering I've been looking for an ESP8266 (ESP-12)
socket for a long time, and the way I see it, It had to have all of these properties: 100% Breadboard Friendly No soldering
required Snap Fit and snugly hold the ESP8266 DIY from everyday household items Easy to print…... Listed under: How To -
DIY - Projects
219. Energy Saving Switch With Presence Sensor Do you face such situations when you leave your reading lights, table fans or
soldering irons without switching them off and later realize that they were on for too many hours which subsequently jumps
off your electricity bills? Well, if you have such a problem…... Listed under: Sensor - Transducer - Detector Projects
220. Door Open Alarm With Linkit One This is a device that indicates by buzzing whenever the door crosses the specified distance
giving a red light indication.This has been developed by linkit one board received in the giveaway! Its total cost is ~63$
including ~60$ linkit one board.Here's video of it in…... Listed under: Clock Projects
221. Home Automation – RC Lighting Is there an appliance in your house that you wished could be turned on easier? That hard to
reach light that you need every day or a fan? With the LinkIt ONE we can do just that! Specifically we can control an AC
appliance with…... Listed under: Home Automation Projects
222. Simon Says With LinkIT ONE Let's go through a classic beginner projec that combines circuits, code, and fun: Simon Says.
Building your own Simon Says game can be a great way to quickly dive deep into the awesome world of tinkering. You get
experience with building some simple circuits (buttons…... Listed under: Game - Entertainment Projects
223. Portable Solar Auto Tracking System Medomyself is a participant in the Amazon Services LLC Associates Program, an affiliate
advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com
by: Dave Weaver This build is made with aluminum t-slot extrusion. I chose…... Listed under: Solar energy projects

224. Linkit One Motion Sensor Prank Do you want to take revenge from your friend or your elder brother because he fooled you
on a occasion. Are you searching for something by which you can scare anyone and have fun. If that is the case then you are
at the right…... Listed under: Sensor - Transducer - Detector Projects
225. Linkit One Audio Messenger Have you ever met to this problem that urgently you have to go somewhere and you are try to
call your wife or children to tell them about the problem but unable to call them due to some network error. I am sure on
some…... Listed under: Sound - Audio Projects
226. RC Controlled Rgb Led Strip Create your own rc controlled led-strip for individual room illumination! Most rgb-led-strips are
controlled by an infrared remote control. To turn it off or on or change the color, you have to stay in front of the receiver.
This is boring and not really smart.…... Listed under: LED Projects
227. Linkit One BT – Mobile As PC Joystick Playing Games in PC is always fun. Play with joy stick with out key board is some more
fun. No joy stick still no problem u play with your Android smart phone. First i think it is a very simple program. But want to
jump…... Listed under: Phone Projects
228. Linkit ONE: Flame Sensor This instructable will guide you to use a flame sensor with the Mediatek Linkit ONE. A flame sensor
is a device that can detect the presence of fire nearby. A buzzer connected to linkit one beeps when fire is detected by the
sensor. So let's…... Listed under: Sensor - Transducer - Detector Projects
229. Linkit ONE Touch LED This instructable will guide you to glow an LED using a touch sensor which means that the LED will
glow when you touch on the probe of the sensor. The project uses the Mediatek linkit one connected to a touch sensor and
an LED. As…... Listed under: LED Projects
230. Wireless Weather Indicator I decided to use the Linkit One's GSM capabilities to create a weather indicator. This would allow
me to make something both practical and visually pleasing, a wireless weather indicator. Step 1: Materials/Tools Tools
Soldering Iron Computer Linkit One GSM anntenna Battery for Linkit One…... Listed under: GPS Based Projects
231. Interactive Television Show Game Interactive TV is a tamil channel, Where we lot of programs and also interactive games by
call the number and use the mobile button to play the game on the television. Want to do some thing like that for local cable
TV for my friend. So…... Listed under: Game - Entertainment Projects
232. Theft Protector Using Tilt Sensor These days theft has become a serious crime. People are now much more conscious towards
there precious items are purses and jewellery but due to the busy routine of this life we are not able to take care of our
things. That constant detraction of…... Listed under: Sensor - Transducer - Detector Projects
233. Presence Notifier With Push Button These days in families, both men and women have started working. Both men and
women want to succeed in life and for this they have to work hard and spent more time in the offices. Due to this it becomes
difficult for both of them…... Listed under: Other Projects
234. Linkit One Temperature Sensor In this instructable I'm going to how you how to measure the temperature using a Linkit One
and a Lm35 temperature sensor. This project can be a part of a wireless weather monitor, if you have not seen my previous
instructables please check it out,…... Listed under: Temperature Measurement Projects
235. Linkit One Kitchen Timer In this instructable I'm going to show you how to design a kitchen timer using the Linkit One, the
timer has a maximum duration of 30 minutes. And once the timer is done counting down it fires a buzzer to notify you. The
time interval…... Listed under: Clock Projects

236. DC Motor Multiplexer This DC Motor Multiplexer allows you to control up to four DC motors in forward and reverse using
one MOSFET and only 5 digital pins. For this intractable you will require: - DC motors (I used salvaged DC fans)- MOSFET (I
used a 110v 30amp…... Listed under: Motor Projects
237. DC Motor Controller This simple DC motor controller allows for one direction motor control and has been built entirely of
reclaimed electrical parts. Using MOSFET's for motor control instead of control chips, allows for an external power supply and
electric isolation of the motor and control board. Which…... Listed under: Motor Projects
238. LinkIt ONE Powered Wall-E In this instructables, we give a simple example of how to add voice output and distance sensing
on everyone's beloved robot with MediaTek LinkIt ONE. https://youtu.be/_0nQopA9cSE Step 1: Materials 1. Linkit One with
Battery 2. Mono Audio Amp Breakout with speaker 3. VL6180X Time-of-Flight Distance…... Listed under: Other Projects
239. SIMPLE QUADCOPTER ( HUBSAN X4 ) In this Instructable I will let you know the basic building block of a Quadcopter and
how to make it in a very simple way.Only thing you need is some skill on Soldering and few basic tools.I think it will give
opportunity to the new…... Listed under: Drones
240. Reading Sensors With a Microprocessor. In my previous Instructable I showed how simple commands could be used to turn
on a microprocessor output and light an LED. https://www.instructables.com/id/Lets-Program-a-PIC... I should stress I am not
connected with Picaxe and these projects are ones I used in School to teach programming to…... Listed under: Sensor -
Transducer - Detector Projects
241. ChipKIT Parking Obstacle Sensor I've always thought it would be nice to have a car with a parking sensor. I don't want to
spend that kind of money until I pay off my student loans. However I do have the materials to make one myself thanks to a
class…... Listed under: Sensor - Transducer - Detector Projects
242. Microcontroller Based Smart Battery Charger The circuit what you are about to see is a smart battery charger based on
ATMEGA8A with auto cut off.Different parameters are shown via a LCD during different charge states.Also the circuit will
make sound via a buzzer upon charge completion. I built the charger…... Listed under: Battery Projects
243. IoT Device for Serial to Ethernet by Using TCP I know WIZ550S2E solution for monitoring. Recently WIZwiki-W7500ECO
platform was announced by WIZnet. So I implemented a firmware of WIZwiki-W7500ECO by WIZ550S2E SW modification
because I can handle a source code easily. You can know the status of equipment even if it is so far.…... Listed under:
Development Board - Kits Projects
244. 3D Printed Ethernet Telescope I've seen PiKon. it's great. i want make it. not original but add function!! so I made Ethernet
Telescope. it's Project name is WIZKon Telescope !! : ) Step 1: Prepare Material Need these... 3D cad file : i published below
site -> Linkmbed : i use WIZwiki-W7500 or WIZwiki-W7500ECO -> LinkSerial…... Listed under: Internet - Ethernet - LAN
Projects
245. Adding REST-based Web Services to IoT Device for IO Monitoring This project is to make a simple RESTful Web service library
for IoT Devices. The library is written with C language code and on WIZwiki-W7500ECO platform board from WIZnet. With it,
users can implement a RESTful Web service on IoT devices easily. Monitoring IoT devices…... Listed under: Development
Board - Kits Projects
246. How to Make a SensorGlove With Android Connection The aim is to create an input system for mobile devices, which is
controlled by the movements of the fingers, in this case with the help of a glove. Para ver este tutorial en español, por favor
haga click aqui: https://www.instructables.com/id/Como-Hacer-Un-Guan... Step 1: Creating the Glove…... Listed under: Sensor
- Transducer - Detector Projects
247. Blinking Shark Puppet How to make a shark puppet with blinking LED lights for its eyes! The two LED lights are going to turn
on when the shark's mouth is closed the first time, https://youtu.be/acaj1QTpn9g after the first time the lights come on, the
LEDs are going to…... Listed under: LED Projects
248. Adafruit Lightstrips First, you need to know that a lightstrip is a bunch of LEDs daisychained together. The three contacts are +5v, GND and DI (data in,
AKA DIN). If you are using the same lightstrip, you can solder just 3 wires... Now on to building Step…... Listed under: LED Projects

249. RFID Based Home Security System Using 8051 In these days we're here with our subsequent assignment that is RFID and
keypad primarily based security machine. This assignment is implemented by means of the use of 8051. often we are able to
see RFID tags or card in metro teach when we're going…... Listed under: Security - Safety Projects
250. Assistive Technology for People With Communication Disabilities Using Makey Makey Objective: Build a cheap and easy tool
to help people with disabilites to better communicate their basic needs. Materials: - Makey Makey - Used box - my box is 6.5
x 3.5", but you can use a box bigger than that if you want. - 8 Connector…... Listed under: Other Projects
251. Wifi-controlled Telescope+DSLR With Motorized Focuser Motivation: I love astronomy and astrophotography very much. I
am sure that like me, all amateur astronomers would want a inexpensive personal observatory for taking pictures of the
fabulous universe. Astrophotography, especially deep-sky photography, requires high precision in tracking (to counter the
earth's rotation) and…... Listed under: Phone Projects
252. Adding an RTC and OLED to ESP8266-01 The ESP8266-01 only has a limited number of I/O pins (only 4). Fortunately these
pins can be used for I2C communication, allowing us to add a hoist of other chips.I wanted to add an RTC to the ESP8266-01
and for testing purposes I did not…... Listed under: LED Projects
253. Easiest ESP8266 Learning IR Remote Control Via WIFI The ESP8266 is a wonderful microcontroller. They can be purchased
cheaply and have built in wifi. In this guide I will not go over how to flash the ESP8266 module with the basic firmware as this
is covered on the http://ESP8266basic.com web site in detail. All the…... Listed under: Other Projects
254. Twin Lamps Kinoma Element can power 3.3V sensors, but some projects call for the use of higher-current devices. The Tessel
Relay module makes it easy to toggle externally-powered devices on and off. In this project, we control a network of two
lamps using Kinoma Element, capacitive touch sensors, and relays.…... Listed under: Other Projects
255. WeMos D1 Mini Pro Flash NodeMCU Firmware This instructables show how to flash NodeMCU firmware to WeMos D1 mini
Pro. Step 1: Introduction WeMos D1 mini Pro is a new ESP8266 dev board. It is thin, light weight, built-in USB to serial chip
and 16 MB flash! Recently, it is the only…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
256. Blink LED Test on Intel Quark D2000 Development Board What is Intel® Quark™ microcontroller D2000? The Intel® Quark™
microcontroller D2000, is a low power, battery-operated, 32-bit microcontroller with a more robust instruction set than other
entry-level microcontrollers. The first x86-based Intel® Quark™ microcontroller, Intel® Quark™ microcontroller D2000 also
increases input/output options over other entry-level…... Listed under: LED Projects
257. Small Motion Sensing Tin Robot Yay - my first instructible My 6 year old nephew wanted to have a robot to guard his
room, so I decided to build one for / with him. It was supposed to have green eyes that turn red when an intruder is
detected.…... Listed under: Robotics - Automation Projects
258. Bluetooth Temperature Sensor for SmartPhone This guide is going to show you how to create a Bluetooth Temperature sensor to connect to your
cellphone. For my “Dry-Active” project I worked with Nordic nRF51822 chipset. This process is not a single day exercise but it’s pretty straightforward
and “solid” experience. Looking…... Listed under: Temperature Measurement Projects

259. Control a Lamp With ESP8266 and a Relay My 6 year old son likes to sleep with the lights on. Eventhough I fitted his bed side
lamp with a 4 Watt led bulb , I still thought I needed a way to control the lamp without getting up in the middle of the…...
Listed under: Phone Projects
260. It’s 5 O’Clock Somewhere Hello Everyone!, Welcome to our group instructables page. Here, we'll break down all the steps
you'll need to build the "It's 5 O'Clock Somewhere" portable clock. What is it? It's a portable clock, connected to your local
wifi, or paired with your phone, to show…... Listed under: Clock Projects
261. /o!ce Oper@ted Robot In this project, it is aimed to make a contribution to this dream. Controlling the machines and
environment with speech makes human life easier and more comfortable. This project is a simple implementation of this
approach. A robot is controlled by voice commands. Voice command…... Listed under: Robotics - Automation Projects
262. Complete Guide to Design an Advanced Line Follower Robot Line follower is an autonomous robot which can detect a
specific colored line painted on a surface of different contrast, such as white on black. In this project I used infrared
transmitters and receivers to track the black strip on white surface. Due to the…... Listed under: Robotics - Automation
Projects
263. 6*8 LED Display Using a Decoder and Atmega8 Many of you have been wondered by seeing the LCD Display at various
places and would have given a little thought about how the things work behind such a real time display. Let's clear such
confusions and create a 6*8 LED display approximately similar to…... Listed under: LED Projects
264. STONE TFT LCD +ESP32 Line Count and Alarm Brief With the continuous development of single chip microcomputer, the
counting equipment tends to be automatic. It needs automatic technical device with real-time, high efficiency and accuracy
to meet the counting requirements of modern production line. Through the design of esp32 MCU as the core…... Listed
under: LCD Projects
265. Radio Signals on Micro:bit Once you're getting familiar with your micro:bit, there's a whole world of possibilities opening up,
but there are some errors you might run into. Here's how to make two (or more) micro:bit communicate, even if the code is
written on different computers. Step 1: You'll…... Listed under: Radio Projects
266. Network-Connected Lamps (IoT for Beginners) A project for someone who lights up my life... As a Christmas present (albeit
an extremely late one now) for a long-distance friend, I wanted to build lamps that could "talk" to one another, as in "reflect
each other's color animations when simulated." This involved a lot…... Listed under: Internet - Ethernet - LAN Projects
267. Temp. and RH Data Logger With Wifi UI I know! You're thinking: "Oh god... another ESP temperature and humidity silly
project..." but wait! Here are the characteristics that might interest you: this data logger can run for 55 days before
the memory is full (considering a 15 minutes sampling rate and a 64K SPIFFS) It can run for…... Listed under: Other Projects
268. SmartLights – ESP8266 and Led Strip SmartLights is a simple way to automate your home lighting. Unlike Phillips Hue and
other commercial devices, SmartLights is economical and easily customisable . The project requires some technical skill, but
they are fairly simple and can be easily followed. https://youtu.be/pU-5jGmHxok Some of the Features…... Listed under: LED
Projects
269. DIY Persistence of Vision Game Display Are you bored of your regular displays? Have you got a innovative idea for a game?
Have you got a soldering station or somebody to help you with one? Well you are in luck, because with this instructable you
will know the basics of the…... Listed under: Game - Entertainment Projects

270. Fast, Portable and Affordable Oscilloscope and Inductance Meter When turned off, it looks like an ordinary toy car that would
entertain a kid for hours, but actually it is an oscilloscope kit in disguise! The idea and also part of the code for this project
came from another scope called STM-32-O-Scope (aka pigScope), which uses…... Listed under: Metering - Instrument
Projects
271. Waren’s L.E.D Music Visualizer Another basic Arduino project is waiting for you to build! This exciting project will allow you to
create an awesome L.E.D Music Visualizer using few components such as a Microphone module, resistors, L.E.Ds, and
Arduino. This project is perfect for those who really loves music. Everybody loves music (including me)…... Listed under: LED
Projects
272. Solar Draw Burning patterns into stuff with the focused suns rays.... about the level of eighth grade earth science before this
subject was eliminated by our current Secretary of Education. But what if instead of just killing small arthropods with a death
ray and then seeing spots…... Listed under: Solar energy projects
273. Electronic Paper Rock Scissors Game Paper, Rock, Scissors is an old, simple game. Basically each player takes turns to make a
shape with their hands and depending on the combination one player wins each round. A more detailed description of the
game can be found here The game is usually played…... Listed under: Game - Entertainment Projects
274. Building Homie Devices for IoT or Home Automation This instructable is part of my DIY Home Automation series, check out
main article "Planning a DIY Home Automation System". If you don't know yet what Homie is, have a look at homie-
esp8266 + homie from Marvin Roger. There are many many sensors. I'm covering the very basic ones in…... Listed under:
275. Affordable Cellular IoT When deciding what type of connectivity your next project will use cellular tends to be considered an
expensive alternative to WiFi or Bluetooth. This tutorial is meant to break that way of thinking and show how easy and
inexpensive cellular could be with the right…... Listed under: Calculator Projects
276. Object Avoidance Microbit Robot Using the Kitronik Motor Controller Having already experimented with creating a robot
using a cheap motor driver board, I decided to look at the one provided by Kitronik, I liked the look of it as it came with easy
to use screw terminals to attach wires and had 4 inputs…... Listed under: Motor Projects
277. Electronic Dimmer With Memory At home I have a salt lamp. This lamp needs a regular small 15 Watt light bulb that lights up
and warms up the lamp. When the lamp is switched on you normally should not dim the lamp because of the lamp heat that
the…... Listed under: Memory - Storage Projects
278. Bike Analog Speedometer More patents for bicycle improvements have been issued than for any other machine. It is no
wonder that the simplest of mechanical devices invites constant tinkering. If you do a search for speedometers for bikes you
can come up with the old style mechanical contrivance…... Listed under: Metering - Instrument Projects
279. Picaxe Greenhouse Light Sensor Controller Last year 2016 I altered my garden and planted some new stock. Half way through
the growing season I noticed that the right hand Carnation had grown far more vigorously than its twin only 20” away. The
only differences to the plants was that a…... Listed under: Sensor - Transducer - Detector Projects
280. ATTiny44 Guitar Effector A DIY ATTiny44 based guitar preamp+effector. All the audio processing is done digitally on-board.
So it is definitely not a HiFi system, but something you can definitely have fun programming. You can program the audio
properties in Arduino IDE and create mobile apps that talk…... Listed under: Sound - Audio Projects
281. MQTT and Wifi Powered Mailbox Flag Note: updated with new firmware, a schematic and a tips for a programmer. A couple of years I embarked on
my own home automation project. It started off by building a server controlled 433 MHz transmitter build with an Arduino to switch lots of cheap…...

Listed under: Internet - Ethernet - LAN Projects
282. Instructables Hit Counter (ESP8266-01) Some time ago, I tried to make an "Instructables Hit Counter" using the Instructables
API, and an Arduino Uno with a wired network shield. However, with the limited RAM of the Arduino Uno, I was unable to get
the system to work. A while ago, I noticed…... Listed under: Internet - Ethernet - LAN Projects
283. Wireless Gesture Controlled Robot Using Micro-controller ATmega328 In this wireless gesture controlled robot project I am
going to control a robot using hand gestures. This is an easy, user-friendly way to interact with robotic systems and robots.
An accelerometer is used to detect the tilting position of your hand, and a microcontroller gets different…... Listed under:
Robotics - Automation Projects
284. VivoGame VivoGame (something like "liveGame" in english) is a funny 2 players game whose goal is hit a target with a
automated dart. One player wear a "glasses" that doesn't let him see the target. 3 leds that replace each lens, allow the other
one, who…... Listed under: Game - Entertainment Projects
285. Weather Monitoring System Using TIVA Hi There Everyone, This is Tahir Ul Haq and introduces you to another member in the
family. This time the project is named as Weather Monitoring System. This is another TIVA based project presented by
students of UET LHR. Weather monitoring plays an important role…... Listed under: Other Projects
286. DIY Cheapest Bluetooth Controlled Home Automation https://youtu.be/7I8b6yBJvXE Step 1: COMPONENTS REQUIRED
Bluetooth module (HC-05)AT89S52/C51/S51/C52 microcontrollerRelay Driver ULN2003ARelayResistances and capacitors as
circuit diagram depicts(below)power module(if the input is more than 5V or else not necessary)IC 7805(5V voltage
regulator)1000uF capacitor10uF capacitorled and resistance(as per convenience so that led doesn't get damaged)
IMPORTANT NOTE:…... Listed under: Home Automation Projects
287. Simple 3 Button On-off With 12f629 (mikroC) a simple 3 buttons on-off with pic12f629. it's written with MikroC Step 1: The
Code... start the code with ''int''---------------------------------------------------------- int x0,x1,y0,y1,z0,z1; ////// with this the
GPIO outputs could stay on or off void main() { GPIO = 0x00; ////// all outputs are 0 CMCON…... Listed under: Other Projects
288. OLED Display (SPI) With Particle Photon Particle Photon is a tiny micro controller, just about the size of an arduino nano. But
the photon is designed for easy IoT prototyping, it supports OTA updates to its firmware. So all we have to do is get it
connected to the internet and we…... Listed under: LED Projects
289. Programming P89V51RD2 (8051 Microcontroller) on Breadboard In this instructable, I am going to give step wise procedure
of programming a P89V51RD2 microcontroller on breadboard. If you are directly seeing this tutorial, then please see my
previous tutorial on basic breadboard power stage here : https://www.instructables.com/id/Breadboard-5V-Pow... In this
tutorial we are going to…... Listed under: Microcontroller Programmer Projects
290. ESP32 Solar Weather Station For my first IoT project I wanted to build a Weather Station and send the data to
data.sparkfun.com. Small correction, when I decided to open my account in Sparkfun, they were not accepting more
connections, so I choose another IoT data collector thingspeak.com. Continuing... The system…... Listed under: Solar energy
projects
291. Entertainment Center Cooling System As nice as an entertainment center with all the AV equipment neatly stacked behind a
glass door looks, the ventilation leaves a lot to be desired, which meant temperatures inside the enclosure were often well in
excess of 100F. I could just leave the door…... Listed under: Game - Entertainment Projects
292. MQTT Based Fire Detection System In recent days, automatic fire detection and control is becoming very essential to reduce the fire in a building or
an industry. It provides real-time surveillance, monitoring and automatic alarm. A key aspect of such systems is to identify a developing fire
emergency in a…... Listed under: Clock Projects

293. Voice Controlled Robot Using 8051 Microcontroller A voice controlled robot takes specified command in the form of voice.
Whatever the command is given through voice module or Bluetooth module, it is decoded by the existing controller and
hence the given command is executed. Here in this project, I have used Bluetooth…... Listed under: Robotics - Automation
Projects
294. Measure Your WiFi Signal Strength Using Particle Photon WiFi has become an integral part of our life and daily billions of
people use WiFi as a method to access the internet. But the range of WiFi is limited, unlike a cellular connection. A normal
WiFi router usually has a range of about a 100m…... Listed under: Internet - Ethernet - LAN Projects
295. Interactive Sound Poster for Kids Things to Prepare: - Foam Board - Aluminum Foil or Copper Tape - Makey Makey -
Computer ( Or Raspberry Pi & Speaker) - Poster Design Step 1: Design a Poster With a Tappable Button. I created a poster for
Halloween event for kids. It…... Listed under: Sound - Audio Projects
296. Controlling Relay Module From Anywhere in the World With Amazing UI Using Losant Learn how to control relay module
from anywhere in the world with Amazing UI using Losant, this is part 6 of IoT World Series Step 1: Needed Components
Needed components ESP8266 PlatformIO IDE with default project setup Relay Module [Shipping free for a dollar] Jumper
cables…... Listed under: Other Projects
297. Walkera Devo 10 Radio Transmitter Deviation Mod – Control Everything! Universal transmitter to control everything! One transmitter to rule them all.
https://youtu.be/tRdhxRH6yUs The Devo 10 is a programmable radio transmitter from Walkera. When Deviation is installed with a couple of RF
modules, it can almost replace every transmitter for your RTF micro multi-rotors/quadcopters/helicopters and planes.…... Listed under: Metering -
Instrument Projects
298. Wireless Energy Meter With Load Control INTRODUCTION Hi guys am a 3rd Year University Student of Lovely Professional
University, India currently pursuing Electronics and Communication Engineering. Youtube Channel
:::: https://www.youtube.com/channel/UC6ck0xanIUl14Oor... Facebook Profile :::: https://www.facebook.com/arnab.das.bwn
GitHub :::: https://www.facebook.com/arnab.das.bwn Wordpress :::: https://www.facebook.com/arnab.das.bwn This Project is
Based on Atmel's Atmega16 Microcontroller as the main brain for computation. NRF24L01+ Wireless communication
module…... Listed under: Metering - Instrument Projects
299. MonkeyDogTracker Okay, I admit I don’t have a monkey. But would you be looking at this if I didn't mention monkey? And
this would work for a monkey. Does your monkey or dog wander off? Would you like to see where he/she is? Well, they
make…... Listed under: GPS Based Projects
300. Interactive LED Beer Pong Table Create your own Interactive LED Beer Pong Table! This instructable will guide you through all
of the steps to in order to create a one-of-a-kind beer pong table complete with cup detecting RGB pods, automatic ball
washers, a 32x12 ping pong ball LED grid, side…... Listed under: LED Projects
301. ESP8266 / NRF24L01 Breadboard Adapter Have you ever been anxious to receive your new break-out boards, only to find out that the pin layout is
not breadboard friendly? If only those pins were aligned differently. Well, let me show you how I have made an easy breadboard adapter that will…...

302. GPS Data Logger While this is not the first Arduino based GPS Data Logger out there, it may be the most versatile. This
device has a lot of features & even more possible uses. It started with significant inspiration from Mikal Hart's "Reverse
Geocache"TM and the use of…... Listed under: GPS Based Projects
303. Control Daikin AC From Anywhere With Beautiful UI and Losant In this instructable we will learn how to control Daikin air-
conditioner from any point in the world using Losant IoT Enterprise Platform and their amazing UI dashboard The ESP8266 is
a low-cost Wi-Fi chip with full TCP/IP stack and MCU (microcontroller unit) Step 1: How It Works…... Listed under: Home
Automation Projects
304. ESP32: DIY Motor Driver With ESP32 Controller This is the simplest motor driver that could possibly be built using only one
NPN transistor, which is controlled and driven by the ESP32 micro controller board. Step 1: Materials and Tools ESP32
MicrocontrollerDC motorNPN Transistor -- BC337100Ω resistorDiode -- N4148 General PurposeBreadboard
wiresBreadboard'2x jumper…... Listed under: Motor Projects
305. Solar Power System Monitoring In this indestructible I will demonstrate how to make your Own Solar power Monitoring
station .With materials ,Code and electronics parts. we will start with the PCB designed on a fritzing program to sending off
for the PCB ,Soldering it and Installing it into a…... Listed under: Solar energy projects
306. Make a Pocket-Size Theremin With ESP32 Theremin are those unique instruments use to make those alien show theme songs
or sound effect. You may have also heard it in Star Trek, Big Bang Theory, or even a haunted house. They produced a unique
sound from the electromagnetic effects between wires. Here…... Listed under: Sound - Audio Projects
307. Micro:Bit Puppet “Text Messaging”! Nearly all of our wireless communication is done using radio waves*, including phone
calls, text messages, and WiFi. With its built-in radio transmitters and receivers, the Micro:Bit microcontroller makes it super
easy to build all sorts of projects with radio communication. This particular project is…... Listed under: Microcontroller
Programmer Projects
308. Solar Tide Clock Tides. In Anchorage Alaska we live on a point located between two enormous tidal bays--so big in fact that
Captain Cook on his initial survey of the area thought (hopeful thinking) that this entrance would prove to be a "northwest
passage". It is shallow and…... Listed under: Clock Projects, Solar energy projects
309. Simple Altera FPGA Demo This tutorial will show you how to turn on an LED using both the built-in LED on a development
board as well as using a GPIO pin. I happen to be using a DE0 CV Dev board from Terasic. We will be using the Quartus…...
310. Bike Power Pedal IoT Work is of two kinds: first, altering the position of matter at or near the earth's surface relatively to other
such matter; second, telling other people to do so. The first kind is unpleasant and ill paid; the second is pleasant and highly
paid. Bertrand…... Listed under: Other Projects

311. Jar of Fireflies This project uses green surface-mount LED's along with an AVR ATTiny45 microcontroller to simulate the
behavior of fireflies in a jar. https://youtu.be/UeL0LC2IgpQ (note: the firefly behavior in this video has been greatly sped up in
order to be easier to represent in a short film.…... Listed under: Home Automation Projects
312. How to Flash MicroPython Firmware on a ESP8266 Based Sonoff Smart Switch What’s Sonoff? Sonoff is a device line for
Smart Home developed by ITEAD. One of the most flexible and inexpensive devices from that line are Sonoff
Basic and Sonoff Dual. These are Wi-Fi enabled switches based on a great chip, ESP8266. While the Sonoff infrastructure may
work quite well for…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
313. Digital Clock Using Microcontroller (AT89S52 Without RTC Circuit) Lets describe a clock... "Clock is a device that counts and
shows time(relative)"!!! Guess I said it right so lets make a CLOCK with ALARM feature. NOTE: it will take 2-3 minutes in
reading please read the whole project or else I will not be responsible for any part damage.…... Listed under: Clock Projects
314. How to Control ESP8266 Based Sonoff Basic Smart Switch With a Smartphone Sonoff is a device line for Smart Home
developed by ITEAD. One of the most flexible and inexpensive devices from that line are Sonoff Basic. It is a Wi-Fi enabled
switch based on a great chip, ESP8266. This article describes how to set up the Cloud4RPi service on a Sonoff Basic smart…...
315. Interfacing 8051 Microcntroller With 16*2 Lcd in Proteus Simulation This is a very basic project of 8051. In this project we are
going to tell you about how we can interface 16*2 lcd to 8051 microcontroller. So here we are using full 8 bit mode. In the
next tutorial we will tell about 4…... Listed under: LCD Projects
316. Interfacing 8051 Microcontroller With Lcd in 4-bit Mode In this tutorial we are going to tell you about how we can interface
lcd with 8051 in 4-bit mode. Step 1: Software Used: As we are showing proteus simulation so FOR CODING AND
SIMULATION YOU REQUIRED: 1 Keil uvision: Their are lots of product from…... Listed under: LCD Projects
317. How to Count From 0 to 99 Using 8051 Microcontroller With 7 Segment Display Hello everyone, In this tutorial we are going
to tell you about how to count from 0 to 99 using two 7 segment display. Step 1: Software Used: As we are showing proteus
simulation so FOR CODING AND SIMULATION YOU REQUIRED: 1 Keil uvision: Their are…... Listed under: Interfacing(USB -
RS232 - I2c -ISP) Projects
318. Keypad Interface With 8051 and Displaying Keypad Numbers in 7 Segment In this tutorial I'm going to tell you about how we
can interface keypad with 8051 and displaying keypad numbers in 7 segment display Step 1: Software Used As we are
showing proteus simulation so FOR CODING AND SIMULATION YOU REQUIRED: 1 Keil uvision: Their are…... Listed under:
Security - Safety Projects
319. Memory-Card Made of CMOS EPROM’s The instructable created by me will help you to build a huge memory capactiy which
will come in handy for many projects and measurements. The memory card is suitable for multi-usage and can be way more
realaiable in comparison to flash cards and other type…... Listed under: Memory - Storage Projects
320. DIY Temperature Logger With STM32F103, MicroSD Card and DS18B20 I'm currently building a temperature logger for some
guys doing a research in biology. Tried to make it as small as possible, with temperature sensor that can be crammed in small
space. Since the first revision slash prototype of the device was incredibly simple to…... Listed under: Temperature
Measurement Projects
321. Fun Micro:bit Robot – EASY and Inexpensive! BBC micro:bits are great! They are easy to program, they're packed with
features like Bluetooth and an accelerometer and they're inexpensive. Wouldn't it be great to be able to build a robot car that
costs next to NOTHING? This project is inspired by the desire…... Listed under: Robotics - Automation Projects
322. Music Synthesizer Based on DE0-Nano-SoC Music Synthesizer This music synthesizer is quite simple : you just have to blow, sing, or even play music in
front of the microphone, and the sound will be modulated and sent through the speaker. Its specctrum will also appear on the LCD display.The
Music…... Listed under: Sound - Audio Projects

323. EBot8 Object Following Robot Have you ever wondered to make a robot that follows wherever you go? But just couldn't?
Well... Now you can! We present you the object following robot! Go for this tutorial,like and vote and maybe you can do it
too!! Step 1: Gather the Materials…... Listed under: Robotics - Automation Projects
324. Space Battleship Yamato 2199 With Trinket Microcontrollers Because of the remake of the animation and movie of Space
Battleship Yamato, in addition to the attractive design of Bandai model. It make me interest to build this space battleship
model again. Bandai not mention its scale, maybe ~1:2500 by estimation. https://youtu.be/b5TzmONvX3o
https://youtu.be/SdxBiHjwRUM Step…... Listed under: Microcontroller Programmer Projects
325. Solar Coaster The iconic scene from Jurassic Park came in the car where the glass of water resonated with the approaching
footsteps of the T-Rex (spoiler). The original scene was done according to web blogs by someone carefully boinging a
musical string attached to the support for…... Listed under: Solar energy projects
326. Mail Alarm After completing my GSM Home Alarm V1.0 and some time of using, I decided to make some modifications. In
the hardware the main changes are the replacement of the ultrasonic sensor and the introduction of a keypad. On the
software, I change the SMS notification by e-mail.…... Listed under: Clock Projects
327. How to Make an Interactive Sound Wave Print In this tutorial we are going to show you how to make an interactive sound
wave print within a picture frame, so you can see and hear your favourite song at the same time! When you touch the print
through the glass of the frame,…... Listed under: Sound - Audio Projects
328. The ULTIMATE Gumball Machine What is ultimate? Infinite RGB? How about a cool LCD touchscreen? Maybe even some
completely unnecessary wifi capabilities? How about all of them- in a gumball machine. DFRobot reached out to me to create
a project that uses their 2.8" TFT screen, so I made the…... Listed under: Game - Entertainment Projects, Uncategorized
329. The KIM Uno – a 5€ Microprocessor Dev Kit Emulator The KIM Uno is a portable, software defined dev kit for (retro)
microprocessors. But let me introduce the idea of it by going back in time: Back in late 2018 it came to my mind, that I
wanted to build a small portable microprocessor dev kit, just…... Listed under: Microcontroller Programmer Projects
330. Micro:bit Compass This instructables show how to use micro:bit to make a simple digital compass. Step 1: Get a Micro:bit If
you not yet have a micro:bit, you may get a micro:bit here: https://microbit.org/resellers/ Step 2: Optional: Battery Holder If
you want to make the digital compass portable,…... Listed under: Microcontroller Programmer Projects
331. PyPortal Splatoon 2 Schedule Display Fun display of current and upcoming Splatoon 2 stages in Turf War and Ranked games,
Ranked game type, and Salmon Run schedule using an Adafruit PyPortal. Cycle through the schedule by pressing on the
touch screen. Backgrounds are randomly cycled for eye candy. The optional…... Listed under: Game - Entertainment Projects
332. ESP32 Robot Using Servos I have been experimenting using different ESP32 development boards, recently I ordered of the
TTGO T-Beam variety which come with a Battery socket to add your own 18650 Lipo, this really takes some of the power
regulation complexity out of building a small robot, as…... Listed under: Robotics - Automation Projects
333. Makey Makey Game Show Buzzer This instructable is designed to help you build a simple game buzzer system for classroom
review games. In this Instructable, you will create simple cardboard switches that will work with a Makey Makey and will be
coded using Scratch. Supplies: 4 Pieces of Cardboard (3 x…... Listed under: Game - Entertainment Projects

334. Sinewave and Cosinewave Signal Generator For an upcoming project I need a signal generator that produces a sine wave and
a cosine wave*. The easiest way would be to buy a signal generator. I also could buy one of those amazing integrated circuits
that Analog Devices makes and build a…... Listed under: Internet - Ethernet - LAN Projects
335. Alexa-controlled Adam Savage Pumpkin All the lights in my house are smart so I've got pretty used to yelling at them to
switch on and off, but it ends up making me look dumb when I yell at a light that isn't. And I look especially dumb when
yelling…... Listed under: LED Projects
336. Weight Sensor Coaster This Instructable will allow you to build a drink coaster with a weight sensor in it. The sensor will
determine the amount of liquid in the glass placed on the coaster and send this information through WiFi to a webpage.
Additionally, the coaster have LED…... Listed under: Sensor - Transducer - Detector Projects
337. Basic Mobile Phone Using STM32F407 Discovery Kit and GSM A6 Module Have you ever wanted to create a cool embedded
project?. If yes, how about building one of the most popular and everyone's favorite gadget i.e Mobile Phone!!!. In this
Instructable, I will guide you on how to build a basic mobile phone using the STM32F407 Discovery…... Listed under: Phone
Projects
338. MicroPython Program: Is the Toilet Occupied? Our office is a large group office with limited bathroom space."I" often find
that I have no room to go to the bathroom, so I have to wait so long that I feel embarrassed. The experiment used
MakePython ESP8266 to set up a detection server…... Listed under: Microcontroller Programmer Projects
339. WiFi RFID Reader The main idea was to read in 13.56 MHz RFID (tags / tokes / stickers / wristbands / cards) by a magic box
and post the RFID UID to a local database by WiFi network. This instructable builds the base of the whole system -…... Listed
under: Internet - Ethernet - LAN Projects
340. INFRA RED REMOTE CONTROLLED ROBOCAR USING AVR (ATMEGA32) MCU The present PROJECT describes a design and
implementation of an infrared (IR) remote controlled RoboCar which can be used for various automated unmanned control
applications. I have designed remote controlled RoboCar(left-right/front-back motion). The entire system is based on
microcontroller (Atmega32) that makes the control system…... Listed under: LED Projects
341. Using a Quadrature Encoder With an ATtiny 2313 and an OLED Display In this instructable you'll learn how to use a rotary
encoder (see http://en.wikipedia.org/wiki/Rotary_encoder ) with a microcontroller and how to display the numeric value as a
bar and a numeric value on an OLED display. See the video below for the project in action. The…... Listed under: LED Projects
342. 2cm Height 7 Segments 6 Digits AVR Clock With 4 Digits Thermometer This project is explaining how to create yourself a 6
digits 7 segments clock with AVR microcontroller Step 1: Prepare the Parts for This Project We need to prepare a parts for this
project, 6x 7 Segments Common Anode 6x PNP transistors for driver, I…... Listed under: Clock Projects
343. Temperature Control System Using Labview (Atmega32) This work describes a framework of ON/OFF, proportional and linear
temperature control systems. The design and implementation of this process is done using LABVIEW, virtual workbench
software. The project involves includes data acquisition, data processing and the display of data. At the initial stage Data…...
Listed under: Temperature Measurement Projects
344. Firmware Upgrade for USBASP Clone – Fixing Error Setting USBASP ISP Clock USBASP is one of the most popular
programmer for AVR Microcontroller by Thomas Fischl. It is one of the oldest programmer for AVR. And very common being
used with AVRdude software. There are many GUI based on AVRDude, such as: embedXcode AVR8 Burn-O-Mat AVRDUDESS
BitBurner avrdude-gui khazama…... Listed under: Clock Projects
345. Low Speed AVR Oscilloscope V2.00 (Is Updated on 19 Mar 2011) >> The firmware was updated on 19 Mar 2011 << A few months ago a friend of
mine -car mechanical at profession- told me that he had problem with some car sensors. He couldn't check, with a simple multimeter, if a sensor was
working properly.…... Listed under: LCD Projects

346. Learn About Microcontrollers This Instructable was designed to answer the question: how do I get started in
microcontrollers? Now, in clear, simple English, you can learn what a microcontroller is, and how to use one. You will learn
how to make everything that you need to get started.…... Listed under: Microcontroller Programmer Projects
347. Homemade Battery Monitor Using AVR I want to share my experiment with voltage divider, ADC and AVRHomemade battery
monitor using AVRIt's pretty simple the sensor are only two resistors and zener diode with capasitor, I don't buy them, I've
found it in my box.We can use it for monitoring our…... Listed under: Battery Projects
348. Measuring Tempurature Using Sensor(LM35) and Atmega32 A digital thermometer is a good project in microcontrollers
because it provides an opportunity to learn using sensors to measure the real world signals that are analog in nature. I am
trying to describes a similar project based on a Atmega32 microcontroller and an…... Listed under: Temperature Measurement
Projects
349. Temperature Sensor(LM35 ) Interfacing With ATmega32 and LCD Display| Automatics Fan Control Step 1: In this project, You
will learn How to interface a Temperature Sensor(LM35 ) with AVR ATmega32 Microcontroller and LCD display. Before This
Project you have to need Learn about following articles how to add lcd library in avr studio| avr microcontroller tutorial
introduction…... Listed under: Temperature Measurement Projects
350. Debugging AVR Code in Linux With Simavr I recently started programming AVR chips, namely the ATTiny85. They can be
programmed using C, compilers are readily available in Ubuntu, and you can do a LOT with them - just search for avr on this
site! Anyway, I was having some trouble with my…... Listed under: LED Projects
351. Interfacing PS2 Controller With AVR -Bit Bang Hey friends in this instructable I will show you how to interface sony PS2
controller with AVR microcontroller .This will be your handy code which you can be used in future to control robots .You can
get analogue value from joystick which can be used…... Listed under: Motor Projects
352. Swiss AVR Knife The Swiss AVR Knife bundles a number of AVR programming projects together in a single convenient Altoids
Gum Tin. Because of the flexibility afforded by microcontroller programming, it also provides a starting point for any number
of projects based on LEDs and sound output. The…... Listed under: Microcontroller Programmer Projects
353. How to Use the Dragon Rider 500 With Your AVR Dragon This instructable is a crash course in how to use some of the
features of the Dragon Rider 500 from Ecros Technologies. Please be aware that there is a very detailed User's Guide available
on the Ecros website. The Dragon Rider is a interface board…... Listed under: LCD Projects
354. AVR Microcontroller. Pulse Width Modulation. Сontroller of DC Motor and LED Light Intensity. Pulse Width Modulation
(PWM) is a very common technique in telecommunication and power control. it is commonly used to control the power fed
to an electrical device, whether it is a motor, an LED, speakers, etc. It is basically a modulationtechnique, in which the
width…... Listed under: Motor Projects
355. Introduction to ADC in AVR Microcontroller | for Beginners In thid tutorial you will know everything ADC in avr
microcontroller Step 1:
What Is an ADC? An ADC, or Analog to Digital Converter, allows one to convert an analog voltage to a
digital value that can be used by a microcontroller. There are many…... Listed under: Microcontroller Programmer Projects

356. Getting Started With Atmel AVR and BASCOM I have seen plenty of Instructables showing how to work with microprocessors,
but they all assume that you have worked with them before and know what you are doing. I have not seen an Instructable
that takes you from nothing and builds on each step.…... Listed under: Battery Projects
357. Cheap STK500 AVR Programmer for Atmel Studio Atmel Studio is a powerful tool for making AVR programs. But writing a
program is the first step. To use your program, you must make a circuit and transfer your code into the microcontroller. You
can program your AVR from Atmel Studio by the…... Listed under: Microcontroller Programmer Projects
358. AVR Microcontroller Fuse Bits Configuration. Creating and Uploading in the Flash Memory of Microcontroller the LED Blinking Program.
https://youtu.be/6rkRAnkuqM0 In this case we will create simple program in C code and burn it into the memory of the
microcontroller. We will write our own program and compile the hex file, using the Atmel Studio as the integrated
development platform. We will configure fuse bits and…... Listed under: LED Projects
359. AVR Microcontroller. Toggle LED’s Using a Push Button Switch. Push Button Debouncing. https://youtu.be/YIZiwaXxtco In this
section, we will learn How to make program C code for ATMega328PU to toggle the status of the three LED’s according to
the input from a button switch. Also, we have explored a solutions to the problem of is ‘Switch Bounce‘. As…... Listed under:
LED Projects
360. Density Based Traffic Signal System using Microcontroller Nowadays, controlling the traffic signal becomes major issue
because of rapid increase in automobiles and also because of large time delays between traffic lights. So, in order to rectify
this problem, we will go for density based traffic lights system. This article explains you how…... Listed under: Microcontroller
Programmer Projects
361. Microcontroller Projects: Home Automation System In this era of digital revolution, we are surrounded by smart devices that
are capable of making decisions on their own without much human intervention. Our home can also be made smart by
implementing a real-time home automation system that monitors parameters like power consumption…... Listed under:
362. Line Follower Robot using Microcontroller Have you ever made your own robot? Here is a very simple and easy robot. In this
project, I will explain how to design and build a Line Follower Robot using microcontroller. The Line Follower Robot is a basic
robot that follows a specific path…... Listed under: Robotics - Automation Projects
363. Microcontroller Projects: Sonar Water-Level Meter Three-fourths of the earth is water, out of which 97 per cent is saline (in
oceans, seas and groundwater). The remaining 2.5 per cent to 2.75 per cent is fresh water, out of which 1.75 per cent to two
per cent is frozen in glaciers,…... Listed under: Battery Projects
364. RFID based Attendance System Most educational institutions’ administrators are concerned about student irregular
attendance. Truancies can affect student overall academic performance. The conventional method of taking attendance by
calling names or signing on paper is very time consuming and insecure, hence inefficient. Radio Frequency Identification
(RFID) is an interesting solution in…... Listed under: Radio Projects
365. AT90S1200 D.D.S. FUNCTION GENERATOR The presented project is a function generator for sinusoidal and square signals
production. The output frequency covers the range from 10 Hz to 100 KHz with a step of 2 Hz. The waveform
synthesis... Electronics Projects, AT90S1200 D.D.S. Function Generator "avr project, microcontroller projects, " The presented
project is…... Listed under: Sensor - Transducer - Detector Projects
366. GAS DETECTOR CIRCUIT ATTINY45 Gas sensors are employed in a wide range of applications in the fields of safety, health,
instrumentation etc… Common examples are domestic/commercial alarms for explosive or toxic gases or in automotive
application, as gas... Electronics Projects, Gas Detector Circuit ATtiny45 "avr project, microcontroller projects, " Gas sensors are
employed…... Listed under: Sensor - Transducer - Detector Projects
367. UNINTERRUPTIBLE POWER SUPPLY UPS AT90S8515 PWM with AT90S8515 a good practice to understand the logic can give
200w Power should be developed for more. The driver circuit method used in section H-Bridge driver integrated HIP4080 I
have in the... Electronics Projects, Uninterruptible Power Supply UPS AT90S8515 "avr project, microcontroller projects, " PWM
with…... Listed under: Battery Projects
368. MICROCONTROLLER GSM ALARM AND CONTROL CIRCUITS Now quite a popular topic with Cell Phone Control with Microchip pic series for those
who want to do these types of projects that could give clues will limp a few projects, including projects... Electronics Projects,Microcontroller GSM
Alarm and Control Circuits "avr project, microcontroller projects, " Now quite…... Listed under: Clock Projects

369. MICROCONTROLLER CONTROLLED DIGITAL POWER SUPPLY CIRCUITS ARCHIVE NXP80C31, PIC16F876, PIC12F629,
PIC18F452, PIC16F876, PIC16F870, PIC18F252, HC908QT4 made with integrated power sources in various voltage and power
MCU of microcontrollers in power electronics used always been interested Unfortunately this type MCU, PIC,... Electronics
Projects, Microcontroller Controlled Digital Power Supply Circuits Archive "avr project, microcontroller projects, "
NXP80C31, PIC16F876,…... Listed under: Circuits
370. MICROCONTROLLER CONTROLLED BATTERY CHARGING CIRCUITS PIC Series Microcontroller ATMEL etc. Battery battery
charger integrated circuits made using the PIC16F819, PIC16F84, PIC16F876, ATMEGA32, AT90S4433-PCR, AT90S1200-P,
based on the ATmega8’s 7units applications Microcontroller controlled battery charging circuits all files: microcontroller-
controlled-battery-charging-circuits.rar alternative... Electronics Projects, Microcontroller controlled battery charging
circuits "avr project, battery charger circuit, microchip projects,…... Listed under: Battery Projects
371. MICROCONTROLLER CONTROLLED ROBOT PROJECTS Multi-robot projects have been realized with the microcontroller. In
addition to professional practice ‘projects have simple robot Most of the projects in the PIC16F series microcontrollers used
ATMEL series over with no project varieties... Electronics Projects, Microcontroller Controlled Robot Projects "avr project,
microcontroller projects, " Multi-robot projects have been…... Listed under: Robotics - Automation Projects
372. OLD CD ROM TRACK PLAYER WITH MICROCONTROLLER Old Cd Rom in handy if you want to make a Track Player PIC16F877
and AT89C51, AT89S52 controllers are made with good projects. Add to My Cdrom the features of the project with
PIC16F877:... Electronics Projects, Old Cd Rom Track Player with Microcontroller "avr project, microchip projects,
microcontroller…... Listed under: Other Projects
373. AVR TEMPERATURE MEASUREMENT SYSTEM Atmel AVR, Atmel microcontroller series with a super “Temperature Control
Measurement System” 16 sensor inputs 4 alarm inputs and the computer’s connection. Temperature measurement, alarm, an
exemplary application in the PC communication This measuring... Electronics Projects, AVR Temperature Measurement
System "avr project, microcontroller projects, " Atmel AVR, Atmel microcontroller…... Listed under: Temperature Measurement
Projects
374. MONITOR AUDIO RADIO SPECTRUM ATMEGA8 Atmega8-16 ac circuits with LEDs monitor the spectrum vu-meters of the
advanced state of our LCD and LED spectrum analyzer circuit looks very nice variety of testing everything in the middle video
There are...Electronics Projects, Monitor Audio Radio Spectrum Atmega8 "atmega8 projects, avr project, microcontroller
projects, " Atmega8-16…... Listed under: Radio Projects, Sound - Audio Projects
375. WHEELS BIKE LIGHT CIRCUIT ATTINY2313 a flashy accessory for your bike 74LS595N 25LC080P a good practice based on the
software with all the details have pcb diagram hex code schema (schema) and PCBs (br) Latest eaglecad prepared
by...Electronics Projects, Wheels bike light circuit "avr project, microcontroller projects, " ATTINY2313 a flashy accessory…...
376. ATMEGA162 LCD OSCILLOSCOPE CIRCUIT A very nice project cost is a bit high in our country, even hard to find parts Atmel
AVR microcontroller series dealing with this type of project is ideal for those who want to... Electronics Projects, ATMEGA162
LCD Oscilloscope Circuit "avr project, microcontroller projects, " A very nice project…... Listed under: LCD Projects
377. ATMEGA8 AT90S4433 WIRELESS RF TEMPERATURE TRANSMITTER And a beautiful project with ATmega8 AT90S4433 your
computer from a remote location with the location’s wireless RF system temperature data come Mailbox temperature
measured in the test program with garden-temperature condition is displayed... Electronics Projects, ATmega8 AT90S4433
Wireless RF Temperature Transmitter "atmega8 projects, avr project, microcontroller projects, "…... Listed under: Medical -
Health based Projects, Temperature Measurement Projects
378. LM3886 TDA7318 DIGITAL AMPLIFIER AT90S8535 AT90S8535, TDA7318 and LM3886 have been realized with digital amp
system LED Indicator-signal input selection can be made, unfortunately explanations could not solve in a language but
ATMEL microcontroller dealing with people a... Electronics Projects, LM3886 TDA7318 Digital Amplifier AT90S8535 "audio
amplifier circuits, avr project, ic amplifier,…... Listed under: Sound - Audio Projects
379. ATMEGA168 MOOD POLY CONTROLLED INTERACTIVE LED LIGHT “Polycontrolled Interactive LED Mood Light” is based on Atmel ATMEGA168/88 quite
a strange RGB LED application design professional as well as various modes, speed, the program’s options. I hope I know the main parts... Electronics
Projects, ATMEGA168 Mood Poly Controlled Interactive LED Light "avr project, microcontroller projects, " “Polycontrolled…... Listed under: LED Projects

380. SPEED

INDICATOR CIRCUITS TACHOMETER ATMEL ATMEGA8 Atmel ATmega series of projects have been realized with the
speedometer and LCD display are the different indicators used circuits. Display circuit used Used atmega8l-8P. Hex file and
prepared by Proteus. Dns file there.... Electronics Projects, Speed Indicator Circuits Tachometer Atmel atmega8 "atmega8
projects, avr project, microcontroller projects, "…... Listed under: Metering - Instrument Projects
381. AT89S52 THERMISTOR CIRCUIT THERMOMETER LCD DISPLAY NTC Thermistor Thermometer based on AT89S52 circuit and
HIH 3160 humidity sensor humidity and temperature information is given. Display LCD display circuit and there are two
versions of the C source code and schema... Electronics Projects, AT89S52 Thermistor Circuit Thermometer LCD Display "avr
project, microcontroller projects, " NTC Thermistor…... Listed under: Circuits
382. MODEL AIRCRAFT PROJECTS Different models of the project Model Aircraft Model airplane models, drawings, model details,
sample circuits, fan motors, etc. .. as well as stock control circuit microchip PIC16F microcontrollers made with a variety of
serial... Electronics Projects, Model Aircraft Projects "avr project, microcontroller projects, " Different models of the project…...
383. COMPUTER CONTROLLED 8-CHANNEL DIMMER CIRCUIT AT90S2313P 200 watt dimmer circuit is controlled from RS232 port
with MOC3021 opto isolated triac driver control program running on xp pretty simple hex to asm code pcb diagram
AT90S2313P. There have also dosyalarıda... Electronics Projects, Computer Controlled 8-Channel Dimmer Circuit 200W
AT90S2313P"avr project, microcontroller projects, " AT90S2313P…... Listed under: Circuits
384. WAV PLAYER CIRCUIT WITH ATMEL ATTINY2313 ATtiny2313 microcontroller circuit with MAX232 PC connection can be
established based on the pc program with wav file loading the output of the power amplifier TDA2003 integrated amp Atmel
Wav Player Circuit Test The... Electronics Projects, Wav Player Circuit with Atmel ATtiny2313 "avr project, microcontroller
projects, " ATtiny2313 microcontroller…... Listed under: Radio Projects, Sound - Audio Projects
385. USB TO LPT CONVERTER CIRCUIT WITH ATMEL ATMEGA8 Converter from USB to LPT parallel port (25 pin SubD receptacle)
with hardware virtualization at input/output instruction level Supports all parallel port modes named SPP, EPP and ECP, 16
Byte FIFO depth USB Low... Electronics Projects, USB to LPT Converter Circuit with Atmel ATMEGA8 "atmega8 projects, avr
project,…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
386. ATMEGA128 ATMEGA32 PC CONTROLLED LED MATRIX ANIMATION LED SIGNS Serve to control the 128×64 graphic LCD with
a preview of the contents of the array and menu graphics. The heart of the controller is Atmega 128 CPU for communication
with the PC corresponds... Electronics Projects, ATMEGA128 ATMEGA32 PC Controlled LED Matrix Animation LED Signs "avr
project, microcontroller…... Listed under: LED Projects
387. AT89S52 8051 RF DC MOTOR SPEED CONTROL Wireless within a certain area with a control circuit for controlling the speed
of DC Motor. Work, should I use to reach my goal I began to identify materials. These materials AT89S52 microcontroller,
our... Electronics Projects, AT89S52 8051 RF DC Motor Speed Control "8051 example, avr project, keil…... Listed under: Motor
Projects
388. 89C51 8051 VOLTMETER THERMOMETER DS1621 ADC0808 ADC 0808 standard data acquisition systems many components
on a single chip host is a member of ADC 0808 8-bit flip makes the process and addresses from input latch 8-channel data
selection (multiplexer) and...Electronics Projects, 89C51 8051 voltmeter thermometer DS1621 ADC0808 "8051 example, avr
project, keil example,…... Listed under: Metering - Instrument Projects
389. CALCULATION OF BODY LENGTH WITH 8051 AND DS89C430 In this project, which is designed using DALLAS DS89C430
microcontroller (in simulation AT89C51RC2) circuit and a marching band, calculated on the length of the body, the LCD
display was performed. Circuit consists of three... Electronics Projects, Calculation of Body Length with 8051 and
DS89C430 "8051 example, avr project,…... Listed under: Calculator Projects
390. AT89C51 8051 GRAPHIC LCD ANIMATION GLCD Animation circuit voltage is applied to the currently displayed map of Turkey
comes first. Subsequently, the Turkish flag and a picture of Mustafa Kemal Atatürk, the next step is to come. Art
world... Electronics Projects, AT89C51 8051 Graphic LCD Animation "8051 example, avr project, keil example,
microcontroller…... Listed under: LCD Projects

391. AT89C51 L293D DC MOTOR WITH DOOR CONTROL CIRCUIT The main purpose of the circuit is to control the gate of the
house. This DC motor and provided with two limit switches is provided by mechanical parts. The two buttons open and
close... Electronics Projects, AT89C51 L293D DC Motor with Door Control Circuit "8051 example, avr project,…... Listed under:
Motor Projects
392. AT89C51 SQUARE WAVE SIGNAL GENERATOR Signal generator test is often the recipients of the amplifiers used in the test
and repair of this equipment. Used as the signal source. Wave detector, radio frequency used in places such as
bridges.... Electronics Projects, AT89C51 Square Wave Signal Generator "8051 example, avr project, keil example,
microcontroller…... Listed under: Radio Projects, Sound - Audio Projects
393. DISEQC TESTER CIRCUIT WITH ATMEL ATTINY13 This device is designed to help define the way DiSEqC-switches to the
working protocols 1.0 and 1.1 and the number of entrances to 4 – x. It feeds the unit from the source of... Electronics
Projects, DiSEqC Tester Circuit with Atmel ATtiny13 "avr project, microcontroller projects, " This device…... Listed under:
Circuits
394. MONITOR TEST CIRCUIT WITH ATMEGA88 color image of a classic test circuit will monitor the audio output of this circuit in
addition to the music in the game are from the old ateri amp could work in the test... Electronics Projects, Monitor Test Circuit
with atmega88 "avr project, microcontroller projects, " color image of…... Listed under: LCD Projects
395. ATMEL ATMEGA8 IR DETECTOR CIRCUIT 8-channel approach to IR detector sensor circuit is realized with ATmega8
microcontroller. I2C bus (TWI, SMBus) are measuring through the obstacle detection, designed for mobile robot. Approach
reflects the beam of infrared light detector... Electronics Projects, Atmel ATMEGA8 IR detector circuit "atmega8 projects, avr
project, microcontroller projects, " 8-channel…... Listed under: Circuits
396. AT89C51 MICROCONTROLLER ANALOG CLOCK FOR GRAPHIC LCD Analog Clock GLCD We use 128×64 pixel graphical LCD
having “HY-12864K” is. This adds the file extension of the LCD connections are provided in PDF. 128 × 64 graphic LCD s have
the same... Electronics Projects,AT89C51 Microcontroller Analog Clock for Graphic LCD "8051 example, avr project, keil…...
Listed under: Clock Projects
397. AT89C51 ANIMATED BMP GRAPHIC LCD DISPLAY AT89C51 microcontroller controlled Animated BMP project usnig Graphic
LCD Display 128×64 project keil source code and proteus isis simulation schematic files Graphic LCD Animated BMP
Schematic project files: at89c51-animated-bmp-graphic-lcd-display.rar author: Cihangir Kılıç... Electronics Projects, AT89C51
Animated BMP Graphic LCD Display "8051 example, avr project, keil example, microcontroller projects, "…... Listed under: LCD
Projects
398. 8051 PS2 KEYBOARD WITH LCD WRITING TEXT PS / 2 protocol used text via a keyboard microcontroller applications that
perform printing text on the LCD The goal here Text via keyboard microcontroller to print text on the LCD. Through keyboard
microcontroller...Electronics Projects, 8051 PS2 Keyboard with LCD Writing Text "8051 example, avr project, keil…... Listed
under: LCD Projects
399. ATMEGA32 10A 2-CHANNEL METER WITH LCD DISPLAY PID Temperature Controller Max232 PC via RS232 serial port
connection can be made According to information I found PID Temperature Controller is accurate temperature control
system i AT90S2313 control system with high mains voltage... Electronics Projects, AT90S2313 Computer Supported PID
Temperature Controller "avr project, microcontroller projects, " PID…... Listed under: Temperature Measurement Projects
400. ATMEGA128 MMC CARD SUPPORTED 3-COLORS LED SIGN MESSAGE BOARD ATmega128 microcontroller based on the
ATmega128 a quality marquee project instead of text information stored on the MMC card codes shared resources At the
beginning this project was to buy a led sign to...Electronics Projects, ATmega128 MMC Card Supported 3-Colors LED Sign
Message Board "avr project, microcontroller…... Listed under: LED Projects
401. ATMEGA8 MOTORCYCLE ALARM CIRCUIT Separate power supply. Signalling on mobile phone call.This function has only a
few hundred euros more expensive equipment. motorcycle into the phone by calling The digital alarm input is a normally
closed contact. The... Electronics Projects, ATmega8 Motorcycle alarm circuit "atmega8 projects, avr project, microcontroller
projects, " Separate power…... Listed under: Sensor - Transducer - Detector Projects
402. 8051 ROBOT ARM STEPPER MOTOR CONTROL In this 8051 Robot ARM application I use for robot arm 3 stepper motor
design, study and is to be informed about the expulsion. Stepping motors to provide work, applied to the ends
of... Electronics Projects, 8051 Robot ARM Stepper Motor Control "avr project, microcontroller projects, " In this…... Listed
under: Robotics - Automation Projects
403. 8051 ELEVATOR PROJECT STEPPER MOTOR CONTROL This application step (step) motor control, input and output ports
through 8051 will examine the circuit by providing lift. We use our stepper motor circuit. As we know, certain steps of the
stepper motor,... Electronics Projects, 8051 Elevator Project Stepper Motor Control "avr project, microcontroller projects, "
This application…... Listed under: Motor Projects

404. MICROCONTROLLER CONTROLLED METAL DETECTOR PROJECTS Result of displays in the form of two scales, which are
estimated to judge the material goal.In addition, the screen is small scale level of response and the current supply voltage.
PIC18F252 The program... Electronics Projects, Microcontroller Controlled Metal Detector Projects "avr project,
microcontroller projects, " Result of displays…... Listed under: Sensor - Transducer - Detector Projects
405. AT89C51 L293D MOTOR CONTROL PROJECT AT89C51 L293D Motor Control Circuit Operation, Our project name and the
name suggests. The treadmill is the motor control is required. When designing this project, I saw fit to use DC motors.
Because the...Electronics Projects, AT89C51 L293D Motor Control Project "avr project, microcontroller projects, " AT89C51
L293D Motor…... Listed under: Motor Projects
406. ATMEGA168 JAVA GUI INTERFACE NIMH CHARGE CIRCUIT Source files are Java and C Diff communication with the computer
via the RS232 port is made available in the Java GUI Interface 2 × 16 LCD display also got on the circuit with... Electronics
Projects, ATmega168 Java GUI Interface NIMH Charge Circuit "avr project, battery charger circuit,…... Listed under:
Interfacing(USB - RS232 - I2c -ISP) Projects
407. AT89C51 5X7 LED MATRIX APPLICATION Circuit Operation: This practice of over 5 × 7 matrix LED A… Z characters are
intended to be created. Provision of characters in source code LEDs (table) was created and when necessary with
the... Electronics Projects, AT89C51 5X7 LED Matrix Application "8051 example, avr project, keil example, microcontroller…...
408. AT89C51 LCD DISPLAY FREQUENCYMETER PROJECT Frequency in all matters relating to the definition based on frequency is
required. In the same way the numeric (digital) Frequency frequency to do the same as the description of the circuit should
be... Electronics Projects, AT89C51 LCD display Frequencymeter Project "8051 example, avr project, keil example,
409. AT89C51 KEYPAD CONTROLLED SCROLLING LED DOT MATRIX TEXT AT89C51 Scrolling LED Circuit Operation: Keypad’t the
values entered the program through is continually monitored, “*” key is pressed unless the display of the first letter that
section required all letters appear, but the... Electronics Projects, AT89C51 Keypad Controlled Scrolling LED Dot Matrix
Text "8051 example, avr project,…... Listed under: LED Projects
410. AT89S52 LCD DISPLAY STEPPER MOTOR CONTROL EXAMPLE AT89S52 Stepper Motor Control Stepper motor, the motor
angular position is changing in steps. This engine is moving into specific steps, according to the windings is controlled by
sending signals. Any stimulus that would... Electronics Projects, AT89S52 LCD Display Stepper Motor Control Example "8051
example, avr project, keil…... Listed under: LCD Projects
411. 8051 CALCULATOR CIRCUIT 8051 Calculator Circuit Operation As seen at half one has to use the keypad and an LCD with
8051. The keypad consists of rows and columns. When the button is pressed certain keys combined... Electronics
Projects, 8051 Calculator Circuit "8051 example, avr project, keil example, microcontroller projects, " 8051…... Listed under:
Calculator Projects
412. 8051 ADC0808 LCD DISPLAY VOLTMETER ADC0808 analog / digital converter of the 8 analog inputs (IN0-IN7) and 8-bit
digital output (OUT0-OUT7) are available. Entries will be transferred to the digital output of the converter which converted to
3-bit ADD,...Electronics Projects, 8051 ADC0808 Lcd Display Voltmeter "8051 example, avr project, keil example,
413. LED DISPLAY SPEED METER CIRCUIT WITH AT89C51 Speed Meter Circuit consists of four parts. These Supply solid floor
Sensor sensor, microcontroller and microcontroller solid hexadecimal numbers we obtained from the 7-segment display
technology with time code converter solid. Program Keil µVision3... Electronics Projects, LED Display Speed Meter Circuit with
AT89C51 "8051 example, avr project, keil…... Listed under: LED Projects
414. 8051 STOPWATCH CIRCUIT WITH LCD DISPLAY Stopwatch Circuit 8051 on behalf of the programming of integrated compiler
program that is used too much in the present case. You are left with only the easiest to use and most advantageous
for... Electronics Projects, 8051 Stopwatch Circuit with Lcd Display "8051 example, avr project, keil example,…... Listed under:
LCD Projects
415. USB CONTROLLED WEB SITE HIT COUNTER ATMEL ATTINY25 WITH DELPHI Web site counts the number of inputs to the
circuit .. Circuit attiny25 an interesting and MAX7219 section based on the indicators used for the 7-segment display 8
hunting and Delphi source code are... Electronics Projects, USB Controlled Web Site Hit Counter Atmel Attiny25 with
Delphi "avr project,…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
416. EMBEDDED RTL8019AS WEB SERVER PROJECT ATMEGA103 I quickly was able to appeal to the network card via a 8-bit data bus. The connectivity of
the network card and thus the RTL8019AS chip via two 8-bit ports of the processor and... Electronics Projects, Embedded RTL8019AS Web Server
Project ATMega103 "avr project, microcontroller projects, " I quickly…... Listed under: Internet - Ethernet - LAN Projects

417. USB PORT RELAY CONTROL WITH ATMEL ATMEGA8 6 relay control units can be made via the usb port usb drive computer
program code and schema files are pcb circuit to regulate the supply 9-12 volt ac section there on the SPI... Electronics
Projects, USB Port Relay Control with Atmel Atmega8 "atmega8 projects, avr project, microcontroller…... Listed under:
418. AT89C51 DS1621 THERMOMETER CIRCUIT AT89C51 Operation of the thermometer circuit DS1621 temperature sensor circuit
using a digital thermometer will tell if I made . As a simple circuit operation is as follows; The numerical value obtained from
the temperature... Electronics Projects, AT89C51 DS1621 Thermometer Circuit "8051 example, avr project, keil example,
microcontroller…... Listed under: Temperature Measurement Projects
419. PC CONTROLLED AT90S2313 LED ANIMATION CIRCUIT Why I write about it? This system uses two ready rolls 5 x 8 LED
matrix, 89C2051, is a programmable serial port and it can be very easy to adapt to the needs of... Electronics Projects, PC
Controlled AT90S2313 Led Animation Circuit "avr project, microcontroller projects, " Why I…... Listed under: LED Projects
420. AT89C2051 WITH DOT MATRIX DISPLAY APPLICATIONS 4 Piece AT89C2051 microcontroller project has been realized with
matrix display isis proteus simulation and asm files available in hex code Atmel AT89C2051 • Compatible with
MCS®-51Products • 2K Bytes of Reprogrammable Flash Memory... Electronics Projects, AT89C2051 with Dot Matrix Display
Applications "avr project, microcontroller projects, " 4 Piece…... Listed under: LED Projects
421. ANALOG LED CLOCK CIRCUIT AT89C2051P 301 LED Analog Clock Project Schema Files of PCB and C51 Compiler Source Code
has been prepared by the C-in hex The clock circuit is made of 301 LEDs with a diameter of 3mm... Electronics
Projects, Analog LED Clock Circuit AT89C2051P "avr project, led projects, microcontroller projects, " 301…... Listed under: LED
Projects
422. PC CONTROLLED FLOWER WATERING CIRCUIT WITH ATMEGA8 As far as I understand an interesting project information via
computer is determined irrigation irrigation is done in the required time data exchange via RS232 com port has made the
source code and diagrams...Electronics Projects, PC Controlled Flower Watering Circuit with ATmega8 "atmega8 projects, avr
project, microcontroller…... Listed under: Sensor - Transducer - Detector Projects
423. ATMEL ATMEGA8 MULTIMETER CIRCUIT (LED DISPLAY) Hello, “Multimeter” was the only title that first came to my mind to.
Voltmeter (positive DC voltage) from 0.00 to 9.99 V and 10.0 – 30.0 V with automatic range switching. Frequency counter
0... Electronics Projects,Atmel Atmega8 Multimeter Circuit (led display) "atmega8 projects, avr project, microcontroller
projects, "…... Listed under: LED Projects
424. 8051 PROGRAMMABLE POWER SUPPLY Circuit Operation: Circuit diagram appears in the 0-5 the entered value from the
keypad circuit, which is connected to port P1 applied to the integrated DAC 0808 DAC output is obtained from the
analog...Electronics Projects, 8051 Programmable Power Supply "8051 example, avr project, keil example, microcontroller
projects, "…... Listed under: Circuits
425. DS1302 RTC 8051 DIGITAL CLOCK CIRCUIT (LCD DISPLAY) 8051 keil example application circuit LCD Display Digital Clock
using DS1302 RTC 8051 Digital Clock Schematic 8051 Digital Clock Circuit keil source code and proteus isis simulation
schematic files: ds1302-rtc-8051-digital-clock-circuit-lcd-display.rar author: @Aytan ASLAN... Electronics Projects, DS1302
RTC 8051 Digital Clock Circuit (LCD Display) "8051 example, avr project, keil…... Listed under: Clock Projects
426. 89C51 DIGITAL CLOCK CIRCUIT From the incoming data encoded in Port0 integrated 7-segment display with 7447
microcontroller integrated ulaşır.7447 binary code from the 7-segment display is used to show. So when it comes to 0000 a,
b, c,...Electronics Projects, 89C51 Digital Clock Circuit "8051 example, avr project, keil example, microcontroller projects, "…...
427. AT89S52 DS1620 THERMOMETER CIRCUIT (LCD DISPLAY) This project gave ds1620’n given as a result of the digitally using
AT89S52 microcontroller is a graphic display of temperature information of the LCD screen. Moreover, the circuit ambient
temperature when it reaches a...Electronics Projects, AT89S52 DS1620 Thermometer Circuit (LCD Display) "8051 example, avr
project, keil example,…... Listed under: Circuits
428. LCD DATE TIME TEMPERATURE AT89C52 DS18B20 DS1302 Atmel microcontrollers with a good example for the use of DS18B20 DS1302 circuit 2 × 16
LCD display with 4 buttons in circuit adjustments can be made The first button is a long hold... Electronics Projects, LCD Date Time Temperature

AT89C52 DS18B20 DS1302 "8051 example, avr project, keil…... Listed under: LCD Projects
429. 8051 MICROCONTROLLER UP DOWN COUNTER CIRCUIT (KEIL) With 8051 DOWN COUNTER The basic principle of this circuit
based on the number entered from the keypad is left counting down or up. # On the keypad to make counting down and
counting... Electronics Projects,8051 Microcontroller Up Down Counter Circuit (keil) "8051 example, avr project, keil…... Listed
under: Circuits
430. PS2 KEYBOARD KEYLOGGER CIRCUIT ATMEL AT89C2051 KeeLog has decided to release an early version of it's hardware
keylogger family to the public domain, including full firmware & software source code, keylogger hardware electrical
schematics, and documentation. This PS/2 key logger is a 100% operational and tested device, assembled and used by hundreds of…... Listed under:
Other Projects
431. RTL8019 ISA WEB SERVER CIRCUIT ATMEGA32 RELAY CONTROL CAMERA CONNECTION Very detailed and complicated
project all of the resources to be shared for different applications feyza can give example might now mikrocontroller.co my
site ATmega32 web server project shared resources of the project the... Electronics Projects, RTL8019 ISA Web Server Circuit
ATmega32 Relay Control Camera Connection "avr project,…... Listed under: Circuits
432. ADC0831 8051 LM35 TEMPERATURE CONTROL WITH LCD SCREEN Adc 0831 with 8051 lm 35 temperature sensor, and a
detailed project examples for the use of inverters. author :Özer Deniz Objective: LM 35 temperature sensor dealt with 0831
ADC analog-to-digital conversion of knowledge,... Electronics Projects, ADC0831 8051 LM35 Temperature Control with LCD
Screen "avr project, microcontroller projects, "…... Listed under: LCD Projects, Temperature Measurement Projects
433. 8051 SRF04 ULTRASONIC DISTANCE METER CIRCUIT 8051 srf04 ultrasonic distance measurement application also contains
information about the different controllers and this information can be useful for applications 8051 microcontroller distance
measurement using ultrasonic transceiver done. Studies, using microcontrollers 8051 with... Electronics Projects, 8051 SRF04
Ultrasonic Distance Meter Circuit "avr project, microcontroller projects, " 8051 srf04…... Listed under: Metering - Instrument
Projects
434. NIMH NICD BATTERY FAST PWM CHARGER CIRCUIT ATMEL AVR Battery charging circuit atmel attiny26lp based on switched
PWM works as a fast charge is doing the switching circuit 100UH coil and irf5305 irl3803 MOSFETs used charging current of
300 mA, 600 mA …...Electronics Projects, NiMH NiCd Battery Fast PWM Charger Circuit Atmel AVR "avr project, battery…...
Listed under: Battery Projects
435. USB JOYSTICK CONVERTER FOR ATARI, AMIGA, COMMODORE 64 Old atari, commodore-64, amiga joystick you can use on
your computer usb converter circuit circuit based on Atmel ATmega8-pin adapter does not require power from the USB port
in addition to working with 5Volt...Electronics Projects, USB Joystick Converter for Atari, Amiga, Commodore 64 "avr project,
microcontroller projects, "…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
436. 27 MHZ WIRELESS KEYBOARD SPY CIRCUIT ATMEL ATMEGA64 In an article “Symantec warns: each word or phrase that you
enter on the wireless keyboard, can be tracked!” Was called I knew it was true, but such a project would never have
thought... Electronics Projects, 27 MHz Wireless Keyboard SPY Circuit Atmel ATmega64 "avr project, microcontroller
projects, "…... Listed under: Circuits
437. DIGITAL AUDIO CONTROL CIRCUIT NOKIA 3310 LCD ATMEL ATMEGA8 TDA7439 My old chassis while stirring an old stereo
on the chassis tda7439 found it and integrate these with making an application decided and ultimately such a nice
application appeared application If we are talking...Electronics Projects, Digital Audio Control Circuit Nokia 3310 LCD Atmel
ATmega8 TDA7439"atmega8 projects,…... Listed under: Sound - Audio Projects
438. TV OSCILLOSCOPE CIRCUIT WITH ATMEGA8515 ATTINY12 Attiny12 ATMEGA8515 a very interesting project based on digital
solid-source software and schema files, PCB’s drawings for people working with Atmel series microcontrollers can give
different ideas can be useful in different projects analogue... Electronics Projects, TV Oscilloscope Circuit with ATmega8515
ATtiny12"avr project, microcontroller projects, " Attiny12 ATMEGA8515 a…... Listed under: LCD Projects
439. ATMEL ATMEGA PROJECTS THERMOMETER LM35, DISPLAY, KEYPAD Atmel ATMEGA series made with micro-controller’s three
projects which can deliver projects bahramelectronic. site manager of @ Bahrain thanks to my brother. 1 – ATMega16 LCD
display temperature measurement (LM35) 2 – 7 segment... Electronics Projects, Atmel ATmega Projects Thermometer LM35,
Display, Keypad "avr project, microcontroller projects, " Atmel…... Listed under: LCD Projects
440. DIGITAL TONE CONTROL CIRCUIT ATMEL ATTINY2313 LM1036 Recently a similar application I’ve done, but ds1844 integrated can not be found had
been a problem AVR reviewing ATtiny2313 `fame four PWM channels, saw direct this practice came to my mind bass treble...Electronics

Projects, Digital Tone Control Circuit Atmel ATTINY2313 LM1036 "avr project, microcontroller projects, " Recently…... Listed
under: Sound - Audio Projects
441. 8051 BASCOM AVR PROJECTS ATMEL CIRCUITS ARCHIVE With Atmel series (AT89C2052, AT90S2313, AT89S8252, etc..) Was
very spacious with quality archive PIC series microcontroller atmel version of the circuit can find a lot. Usb, alarm, LCD, nokia
3310, nokia 6100, display, LED,... Electronics Projects, 8051 Bascom AVR Projects Atmel Circuits Archive "avr project,
microcontroller projects, " With…... Listed under: LCD Projects
442. USB UART CONVERTER PIC16F88 CIRCUIT ATTINY2313 Recently circuit on the web I’ve seen perform this southern been
applying If we are talking application atmel’s famous ATtiny2313 achieves with USB UART converter further circuit 8bit I / O
128-byte EEPROM 32-byte...Electronics Projects, USB UART Converter PIC16F88 Circuit Attiny2313 "avr project, microchip
projects, microcontroller projects,…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
443. ATMEL AT90S2313 COMPUTER-CONTROLLED SCROLLING LED TEXT All details were shared with the marquee circuit
computer control program atmel at90s2313 source software image format PCB, schematics and drawings have OrCAD
source. The marquee on the circuit The marquee circuit 350 leds... Electronics Projects, Atmel AT90S2313 Computer-
Controlled Scrolling LED Text "avr project, microcontroller projects, " All details…... Listed under: LED Projects
444. HDD CLOCK CIRCUIT ATMEL ATMEGA128 DS1307 TDA5410 MOTOR DRIVER Before “Broken HDD Evaluate under the
heading” corrupted hard disks to assess a few apps I’ve used on the web with the sandpaper I I told you about that time had
projects now hardisk... Electronics Projects, HDD Clock Circuit Atmel ATmega128 DS1307 TDA5410 Motor Driver "avr project,
led…... Listed under: Clock Projects
445. 100WATT PV PANEL CONVERTER ATMEGA8 100W DC TO AC ICL7667 ETD34 The use of solar energy will be the topic for a
long time an active electronic circuit is used a lot in this business at one of these inverter dc to ac converters. Ac... Electronics
Projects, 100Watt PV Panel Converter Atmega8 100W DC to AC ICL7667 ETD34 "atmega8…... Listed under: Solar energy
projects
446. POWER LED DRIVER CIRCUIT LED CURRENT SOURCES ATMEGA8 PWM Power LED driver circuit based on Atmel ATmega8 is
working with 12 volt 3 1 watt Luxeon power LEDs with PWM buck converter is operated ATmega-8 a good example source
code to solve logic... Electronics Projects, Power LED Driver Circuit LED Current Sources Atmega8 PWM "atmega8 projects,
avr…... Listed under: LED Projects
447. PCB PRINTING WITH EPSON CX4200 INKJET PRINTER MODIFIED Prepared by: Volkan Sahin – First of all you need to know
when the project was challenging but, if there is the possibility worthwhile CX4200 Epson inkjet to print text by modifying
the... Electronics Projects, PCB Printing with Epson CX4200 inkjet Printer Modified "avr project, microcontroller projects, "…...
448. MICRO ROBOTIC FLY SCREEN CLEANER AT90LS8535 ROBOT BUG A very interesting robot project ratchet içintasarl been
cleaning the flapper cleaner robot brain of the system microcontroller atmel at90ls8535 source software given c.
Uygulayamasa sections of the circuit on the robot project source... Electronics Projects, Micro Robotic Fly screen cleaner
AT90LS8535 Robot BUG "avr project, microcontroller projects, "…... Listed under: Robotics - Automation Projects
449. CNC DRILLING MACHINE CONTROL DIRVE BOARD ATMEL AT89C2051 L297 L298 Printed circuit board drilling machine on the
Atmel AT89C2051 microcontroller L297 L298 motor drivers.. software does not open hex code provided free computer
control program, but other parts of the circuit (motor drives, serial... Electronics Projects, CNC Drilling Machine Control Dirve
Board Atmel AT89C2051 L297 L298 "avr project,…... Listed under: CNC - Printing Machines Projects
450. 2.4 GHZ SPECTRUM ANALYZER CIRCUIT NOKIA 3410 LCD ATMEGA8 Mobile phones with Nokia 3410 LCD screens often used
microcontrollers Atmel ATmega8 and cywm6935 nokia 3410 LCD modules made with a 2.4 GHz spectrum analyzer circuit
Handheld 2.4 GHz Spectrum Analyzer Circuit After visiting... Electronics Projects, 2.4 GHz Spectrum Analyzer Circuit Nokia
3410 LCD ATmega8 "atmega8 projects, avr…... Listed under: Circuits
451. ATMEL ATMEGA8 VIA USB CONTROL CIRCUIT Hi, I have done recently attiny2313’l usb application (ATTINY2313 PIC16F88
USB UART converter circuit) then one needs at this time on I did with ATmega8. RS232 portion of the circuit 15 disuse I
/... Electronics Projects, Atmel Atmega8 via USB Control Circuit "atmega8 projects, avr project, microcontroller projects, "…...
Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects

452. LIGHT FOLLOWING ROBOT WITH ATMEL ATTINY25 Light following robot circuit board on attiny25v not very complicated
circuit Lithium-polymer battery provided with the circuit feeding the tiny H-bridge output (2N3904) drive motors are
controlled with two LDR light is perceived. As... Electronics Projects, Light Following Robot with Atmel ATtiny25 "avr project,
microcontroller projects, " Light following…... Listed under: Robotics - Automation Projects
453. TRANSISTOR TESTER CIRCUIT ATMEGA8 LCD DISPLAY Transistor very useful for testing the circuit, but I do not know more pic
programming with atmel series in seeing this type of advanced applications get confused Transistor test circuit, BJT,
MOSFET, triac,...Electronics Projects, Transistor Tester Circuit ATMega8 LCD Display "atmega8 projects, avr project,
microcontroller projects, "…... Listed under: Circuits
454. ATMEGA8 PROGRAMMABLE CONTROLLER BOARD ELECTRONIC PLC CIRCUIT Tiny Basic Controller (TBC) is a simple device
that can operate as a PLC (program logic controller) for home automation, control, etc. For example, this one can dial-up by
modem to the remote computer and control the system, can control some processes, temperature regulation, battery
charging,…... Listed under: Development Board - Kits Projects
455. FOR ALL THE TELEVISION REMOTE CONTROL (JUST OFF) 90% of all leisure joke circuit television (including plasma, LCD) is
said to work 30 … 50 meters in open space closes the television. Circuit made ATTINY85V-10 micro-controller circuit with two
1.5v AA battery...Electronics Projects, For all the television remote control (just off) "avr project, microcontroller projects, "…...
456. AT89C52 APPLICATIONS EXAMPLES PROTEUS ISIS CIRCUITS (10 PROJECTS) AT89C52 examples of applications can be helpful
for beginners of all samples prepared with simple 3 .5 source lines of code. Bass. Hex, bin, etc.. isis proteus have codes and
simulation files. 0-255 binary...Electronics Projects, AT89C52 Applications Examples Proteus isis Circuits (10 projects) "avr
project, microcontroller projects, "…... Listed under: Circuits
457. ATMEL AT89C2051 CLOCK CIRCUIT WITH LED DISPLAY Pretty stylish digital clock circuit of the display to show information on
the hours, but around kılasik made with 120 LEDs in display attracts attention also has an alarm feature. Microprocessor
AT89C2051 LED clock...Electronics Projects, Atmel AT89C2051 Clock Circuit with LED Display "avr project, led projects,
microcontroller…... Listed under: Clock Projects
458. STEREO 64LEDS VU METER CIRCUIT ATMEGA8 Lately, when I went deeper into programming, I was fascinated by precise A /
D converters in microcontrollers. And so I decided to make a 2x32 LED VU meter with the ATmega8 microcontroller, which
can be bought for example in GME for only 34Kc, and so…... Listed under: LED Projects
459. 3-20V 01-10A POWER SUPPLY CIRCUIT ATMEGA8 LCD AMMETER, VOLTMETER What cannot do more than one radio
amateur? What can not be more than one radio amateur? That's right - without a GOOD power supply, or even better, a
GOOD TWO-CHANNEL power supply. That's right - without a GOOD power supply, or even better, a…... Listed under: Circuits
460. OPERATED WASHING MACHINE CONTROL CIRCUIT WITH ATMEGA32 ATmega32 microcontroller based on the project is
already quite interesting and a professional I see this type of advanced projects ATMEL series Some sections of the circuit
MOC3043 opto diac, MOC3023 isolated with LCD... Electronics Projects, Operated Washing Machine Control Circuit with
ATmega32 "avr project, microcontroller projects, " ATmega32 microcontroller…... Listed under: Circuits
461. THERMOMETER CIRCUIT DS1820 ATMEGA32 SIEMENS S65 LCD Thermometer circuit board ATmega32 used on the LCD
display DS1820 sensor used in the Siemens S65 mobile phone graphic LCD LS020 ATmega32 project’s source code S65 LS020
bitmap bmp files for graphic LCDs and... Electronics Projects, Thermometer Circuit DS1820 ATmega32 Siemens S65 LCD "avr
project, microcontroller projects, " Thermometer…... Listed under: Circuits
462. TANK ROBOT ATMEGA48 BLUETOOTH JAVA PROJECT Introduction After two more complex robots
( Eurobot2008 and Robot2 ), I decided to build a small and simple car. The choice fell on a plastic tune, which was controlled
by two AA pencil monoculars - similar toys can be found in toy shops, on soils or in bazaars. Others are…... Listed under:
463. ATMEL ATMEGA8 NOKIA6100 LCD PCF-8833 APPLICATION Nokia 3310 screen already had several applications with bi-color
LCD at this time I decided to experiment with it. Heavily on the market, the Nokia 6100 LCDs and their controllers for
microchip using Atmel...Electronics Projects, Atmel Atmega8 Nokia6100 LCD PCF-8833 Application "atmega8 projects, avr
project, microcontroller projects, "…... Listed under: LCD Projects

464. TFT LCD OV7660 ATMEL ATMEGA32 APPLICATION EXAMPLE ILI9325 DRIVER Emerging technologies on the market with LCD
prices quite fell microcontrollers with applications proliferate mobile phone, mp4 and graphic LCDs became available,
especially Atmel series with enhanced graphics LCDs can be used ATmega32 320... Electronics Projects, TFT LCD OV7660
Atmel ATmega32 Application Example ili9325 Driver "avr project, microcontroller…... Listed under: LCD Projects
465. TFT LCD DIGITAL PHOTO FRAME ATMEGA128 SD CARD TSC2046 Digital Photo Frame TFT ATmega128 TFT source C code of
practice are used to SPFD5408 TFT LCD 3.2 inch 320 × 240 size images displayed in the SD card. Source: ourdev.cn/ Digital
Photo Frame... Electronics Projects, TFT LCD Digital Photo Frame ATmega128 SD Card TSC2046 "avr project,
466. ATMEGA16 TOUCHSCREEN PROJECT TFT APP AVR GCC ILI9325 Touch TFT application based on ATMega16 processor used in
the 16 MHz frequency drives and ILI9325 OTM3225, source C code (AVR GCC)’s. Source: ourdev.cn 2.4-inch TFT LCD, point-
screen work notes Alternative link: atmega16-touchscreen-project-tft-app-avr-gcc-ili9325.rar... Electronics Projects,Atmega16
Touchscreen Project TFT App AVR GCC ILI9325 "avr project, microcontroller projects, " Touch…... Listed under: LCD Projects
467. ATMEGA128 AVR GRAPHIC LCD APPLICATION SIEMENS S65 LS020 Siemens s65 using the Atmel ATmega128 caption to
display graphics on the LCD all the resources an application prepared S65 LCD driver library, sample text and detailed
graphics shared C code. S65 application is... Electronics Projects, ATmega128 AVR Graphic LCD Application Siemens S65
LS020 "avr project, microcontroller projects, "…... Listed under: LCD Projects
468. AT89C2051 DIGITAL SCALES CIRCUIT ATMEL This is a kitchen scale with a maximum weight of 2.5kg and an accuracy of
10g. Exceeding the range is indicated by an acoustic signal and an LED. Weight is displayed on a four-digit LCD display. The
weight also includes a weight-zero reset button. The power is solved by…... Listed under: Circuits
469. PROGRAMMED DOOR ALARM CIRCUIT ATTINY24 ATTINY13 CONTROLLED This simple mini-burglar alarm on the ATtiny 13
microcontroller is designed to protect apartments, offices, summer cottages ... When the reed switch opens, the alarm beeps
or, with a little refinement, you can send an SMS from a mobile phone. The alarm control is carried out…... Listed under:
Circuits
470. ADC EXAMPLE ATMEGA8 DIGITAL VOLT METER AMMETER AVR PROJECT ADC - analog-to-digital converter (ADC-Analog-to-
Digital Converter). Converts a certain analog signal to digital. Bitrate ADC determines the accuracy of the signal
conversion. Conversion time - respectively, the speed of the ADC. The ADC is embedded in many microcontrollers of
the AVR family and simplifies the use of the microcontroller in any regulation schemes…... Listed under: Metering - Instrument
Projects
471. ATMEL APPLICATION NOTES AND SOURCE C ASM CODE Atmel’s products and practices related to application notes
prepared for the asm code source c c language prepared by the majority of the samples. 138’s application List: 1-Register
and Bit-Name Definitions for the AVR... Electronics Projects, Atmel application notes and source c asm code "avr project,
microcontroller projects, "…... Listed under: Development Board - Kits Projects
472. RF TRANSCEIVER EXAMPLE WATER GUN PROJECT CIRCUIT TX434 ATMEGA8 RX434 The RF transceiver with ATmega8
prepared samples prepared with C language software has all the source code for the application circuit used joke
handmade by remote control a water gun at school students...Electronics Projects, RF Transceiver Example Water Gun Project
Circuit TX434 ATMega8 RX434"atmega8 projects,…... Listed under: Game - Entertainment Projects
473. ATMEL ATTINY15 MICROCONTROLLER EXAMPLE DC TO DC CONVERTER CIRCUIT Atmel ATtiny15 Microcontroller DC to DC
converter circuit 3.6 Li-Ion battery voltage of 5 volts raises a more detailed circuit attiny15 not a good example for software
power control with microcontroller assembly language prepared... Electronics Projects, Atmel ATtiny15 Microcontroller
Example DC to DC Converter Circuit "avr project, dc…... Listed under: Circuits
474. REMOTE-CONTROLLED DIGITAL TIMER CIRCUIT WITH ATMEL ATTINY2313 Based on Atmel ATtiny2313 microcontroller circuit
with the remote control forward / reverse control can be done over time led display are viewing. ATtiny2313 by the time
specified number 9 which is connected to...Electronics Projects, Remote-Controlled Digital Timer Circuit with Atmel
ATtiny2313 "avr project, microcontroller projects, " Based…... Listed under: Clock Projects
475. ATMEGA8 BIPOLAR STEPPER MOTOR DRIVER CIRCUIT L293B Bipolar stepper motor control circuit 6v … 35v inter able to run
power 1 amp on the circuit control, program, sensor, PWM, UART has links ATMega8 output used in motor drive l293b circuit
of... Electronics Projects,ATMega8 Bipolar Stepper Motor Driver Circuit L293B "atmega8 projects, avr project,
microcontroller…... Listed under: Motor Projects
476. 220V SOLDERING IRON TEMPERATURE CONTROL WITH AT89C2051 LED DISPLAY Sold in the market potency heat settings with TRIAC 220v
temperature-controlled soldering iron more advanced version control AT89C2051 microcontroller is provided by heat setting 2 button is made with
indicators, one for led display... Electronics Projects, 220V Soldering Iron Temperature Control with AT89C2051 LED Display "avr project,
microcontroller…... Listed under: Temperature Measurement Projects

477. ACTIVE ELECTRONIC LOAD CIRCUIT ATMEGA88 100W DUMMY LOAD In each electronic device in one form or another there
is a power supply unit (PSU). Of course, because no one will work for free. Before connecting to the circuit, it would be nice to
see how the PSU works at different loads. Personally, I am not…... Listed under: Circuits
478. STAR LED EFFECTS CIRCUIT ATTINY13 PROJECT Stars in the shape of hard work to prepare printed circuit board design for
SMD LEDs to be mounted like a great deal of attention and effort, but finally emerged quite nice circuit
noncontiguous... Electronics Projects, Star LED Effects Circuit ATTINY13 Project "avr project, led projects, microcontroller
projects, "…... Listed under: LED Projects
479. ELECTRONIC PIANO CIRCUIT ATTINY2313 SIMPLE AUDIO PROJECT Atmel ATtiny2313 two 1.5V AA batteries powered
electronic piano circuit connected in series (3V) can be operated. PB3 – PB4 16 on pins 15 and 32 ohm speaker connected to
these pins as exit.... Electronics Projects, Electronic Piano Circuit Attiny2313 Simple Audio Project "avr project, microcontroller
projects, " Atmel…... Listed under: Game - Entertainment Projects
480. How to build alarm security system using motion sensor with PCB Prototyping Introduction Security is important for
everyone from our homes to places of work. You need to feel safe when you are sleeping at night. You might have important
documents that you need to keep private. Sometimes you have property in your house that must be…... Listed under: Security
- Safety Projects, Sensor - Transducer - Detector Projects
481. CNC PROJECT ATMEGA16 X-Y-Z MOTOR CONTROL CIRCUIT ATMega16 microcontroller based on a detailed cnc project with
computer com RS232 on port communicating project’s source C code, schematics eagle CAM (graphic printout is used to
direct the CNC circuitry and sent to)... Electronics Projects, CNC Project ATMega16 X-Y-Z Motor Control Circuit "avr project,
microcontroller projects, " ATMega16 microcontroller…... Listed under: CNC - Printing Machines Projects
482. DSPIC33FJ128GP NOKIA 6100 LCD DRIVER CIRCUIT ATMEGA168 @ Erhan brother Atmega8 prepared with the application
had shared (Atmel Atmega8 Nokia 6100 LCD (pcf8833) application) I In addition to the helpful one more example’ll share the
codes and microchip dspıc33fj128gp both the... Electronics Projects, dsPIC33FJ128GP Nokia 6100 LCD driver circuit
ATmega168 "avr project, dspic projects,…... Listed under: LCD Projects
483. AT90S8535 SG2524 PWM SOLAR PANEL PV INVERTER CIRCUIT Solar Energy PV inverter systems used in energy production a
detailed study about all the details about the project (in English) is. PV conversion control is provided by Atmel
microcontrollers at90s8535 (source software has... Electronics Projects, AT90S8535 SG2524 PWM Solar Panel PV inverter
Circuit "avr project, microcontroller projects,…... Listed under: Solar energy projects
484. NOKIA LCD MODELS PROTEUS ISIS EXAMPLES CIRCUITS LIBRARY Nokia lcd screens, pic, atmel microcontrollers used in this
project, with a lot of other job so popular as talking about the proteus simulation model for the program, set up a virtual
environment, try... Electronics Projects,Nokia LCD Models Proteus isis Examples Circuits Library "avr project, microcontroller
projects, "…... Listed under: LCD Projects
485. FREQUENCY METER CIRCUIT LCR METER ATMEGA328 I have been thinking about building an LC meter for a while since I do
not have a multimeter that is capable of measuring inductance and while the multimeters I have can measure capacitance,
they are not able to give accurate readings for small capacitance…... Listed under: Metering - Instrument Projects
486. SMART REMOTE ATMEGA88 CIRCUIT COPY THE TWO BUTTONS This fun project lets you take control away from the person
holding the remote control by intercepting the invisible signals as they travel through the air so you can play them back to
the TV or video machine. You can also "train" your Remote Hijacker…... Listed under: Development Board - Kits Projects
487. 24V 48W DIGITAL SOLDERING STATIONS ATMEGA8 After a year of using my assembled Microfibers according to the Jendy
documents23 , I decided to build another (third) microfuel. I wanted to reduce the dimensions, use the 24V AC heating
power, to adjust the temperature better and to add additional functions ... Features of micro-drives : temperature range 80
°…... Listed under: Other Projects

488. FAST FOURIER TRANSFORMATION FFT CIRCUIT ATMEGA8 SCT2024 LED DRIVER ATmega8 (TQFP32 package) based on FFT
Circuit applied the entry signals 16 × 16 led display (SCT2024 serial-interfaced LED driver 256 LEDs), you can see in the FFT
circuit source C, hex codes have... Electronics Projects, Fast Fourier transformation FFT Circuit ATmega8 SCT2024 LED
driver "atmega8 projects, avr…... Listed under: LED Projects
489. LED ANIMATION CIRCUIT ATMEGA168 Last year in one of my classes we were required to make an 'artefact' or something
that reflects the interests of the class. Most people make posters and the past two quarters that's what my class did too.
Posters however are static, usually boring, and…... Listed under: LED Projects
490. ILI9325 TOUCH-SCREEN PROJECT TFT ATMEGA644 ELT240320ATP Atmel is a great project with a series of applications can be
made super graphics used in this project Atmega644 the ELT240320ATP GLCD (320 × 240) driver ILI9325 Simple as iPhone
menu has pacman...Electronics Projects, ILI9325 Touch-Screen Project TFT Atmega644 ELT240320ATP "avr project,
microcontroller projects, " Atmel is…... Listed under: Game - Entertainment Projects
491. LABORATORY ADJUSTABLE 0-24V DIGITAL POWER SUPPLY CIRCUIT ATMEGA8 Power supply circuit two separate sections
consisted primarily power solid LM317 based on the current settings for the tl082 opamp used current voltage display
section Atmel ATmega8 microcontroller used optionally this section may not... Electronics Projects, Laboratory Adjustable 0-
24v Digital Power Supply Circuit ATMega8 "atmega8 projects, avr project,…... Listed under: Development Board - Kits Projects
492. CURRENT MEASUREMENT DATA LOGGER CIRCUIT ATMEL AVR, PIC Very high current of the current transformer and with
microcontroller sensitive way measured to be recorded will be useful for source code with 2 sample application circuits one
of the Atmel AVR ATMEGA48 88/168-P...Electronics Projects, Current Measurement Data Logger Circuit Atmel AVR, PIC "avr
project, microcontroller projects, "…... Listed under: Metering - Instrument Projects
493. AUTOMATIC RABBIT FEEDING SYSTEM ATMEGA8 TIMER In fact, feeding, feeding various timing circuits used for business.
Generally puzzling, time-consuming mechanical parts is getting no special circuitry to rabbits in this project but the authors
have used to feed rabbits :)... Electronics Projects, Automatic Rabbit Feeding System ATmega8 Timer "atmega8 projects, avr
project, microcontroller projects, "…... Listed under: Sensor - Transducer - Detector Projects
494. LED HEART CIRCIUT ATMEGA88 Atmel atmega88 PCB LEDs circuit drawing heart looks great, especially boxing PCAD pcb
drawings and diagrams and drawings prepared by the C source code files have a heart-shaped 22 pcs SMD LED flashes
with... Electronics Projects, Led Heart Circiut ATmega88 "avr project, led projects, microcontroller projects, " Atmel atmega88
PCB LEDs…... Listed under: LED Projects
495. LED PROPELLER CIRCUIT AT90S2313 ATINY2313 Printed circuit board layout pcb design effects with LEDs been a good
practice to work in the dark when used with an ultra bright LEDs looks very nice. Atmel AT90S2313 64 LEDs instead
of... Electronics Projects, Led Propeller Circuit AT90S2313 ATINY2313 "avr project, led projects, microcontroller projects, "
Printed…... Listed under: LED Projects
496. ATMEGA16 LEDS SNOW EFFECT CIRCUIT LED SNOW CRYSTAL It really is a great led light application LEDs so fluently is
moving a profit crystalline with mold has been excellent ATMega16 microprocessor 32 Edet output used to all the LEDs
griplar connected software...Electronics Projects, ATMega16 LEDs Snow Effect Circuit LED snow crystal "avr project, led
projects,…... Listed under: LED Projects
497. 15A MOTOR SPEED CONTROL CIRCUIT ATTINY45 PWM Used in motor speed control circuit microcontroller atmel attiny45p
exit number 5 Kubla connected to pin opto pc817 pc817 output while the engine is controlled as isolated MOSFETs have
bs170 and irlz34 Attiny45 Pb4... Electronics Projects, 15A Motor Speed Control Circuit Attiny45 PWM "avr project,
microcontroller projects, pwm…... Listed under: Motor Projects
498. LED EFFECT CIRCUIT ATTINY2313 MULTI FUNCTION Led effect circuits, including myself, a lot of people might be interested,
especially this sort LEDs and LED circuits have great interest in blue, white, LED prices now old and not so expensive
LED... Electronics Projects, Led Effect Circuit Attiny2313 Multi Function "avr project, led projects, simple circuit…... Listed
under: LED Projects
499. RGB LED EXAMPLE CIRCUIT ATMEGA88 ATMEGA8 ATMEGA48 White LEDs, blue LEDs, ultra bright LEDs RGB LEDs saying quite
a lot in the sample application with popular microcontrollers are used in this circuit, atmega8 ATMEGA48 Atmega88 ATmega
output MOSFETs are driven by... Electronics Projects, RGB Led Example Circuit Atmega88 Atmega8 Atmega48 "atmega8
projects, avr project, led…... Listed under: LCD Projects

500. HDD BRUSHLESS MOTOR DRIVER CIRCUIT ATMEGA8 Brushless motor drive circuit used in computers hard drive with
Atmega8 checked the engine ATmega 8 output MOSFET (IR4427, IRFZ44) strengthened engine with A, B, C, D, attached to
either end. Software is written... Electronics Projects, HDD Brushless Motor driver Circuit Atmega8 "atmega8 projects, avr
project, microcontroller projects, "…... Listed under: Motor Projects
501. ATMEGA32 LED CUBE CIRCUIT 74HCT238 On the Internet, atmel, microchip series microcontrollers with a lot Led cube has a
project in this application one of them, but diagrams, photos, supplemented with a detailed description there thanks to this
project...Electronics Projects, Atmega32 LED Cube Circuit 74HCT238 "avr project, led projects, microcontroller projects, "
On…... Listed under: LED Projects
502. USB POWERED INDUCTANCE METER CIRCUIT ATMEGA8 Coil measurement “Inductance Meter” circuit based on Atmega8
microcontroller LCD HD44780 driver and the system’s power supply is taken from the USB port on the computer or adapter
operated with the circuit. Circuit of... Electronics Projects, USB Powered Inductance Meter Circuit Atmega8 "atmega8 projects,
avr project, microcontroller projects, "…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects, Metering - Instrument
Projects
503. ATEMGA168 TLC5940 PWM RGB LED CYLINDER 95 pieces made using RGB LEDs Led cylinder project quite professional
printed circuit board, software quality circuit that is used quite ATEMGA168 microcontroller with integrated LEDs TLC5940
LED driver plowed. Installation was very difficult... Electronics Projects, ATEMGA168 TLC5940 PWM RGB Led Cylinder "avr
project, led projects, microcontroller projects,…... Listed under: LED Projects
504. MULTIFUNCTION DIGITAL AMPLIFIER PROJECT TDA7294 ATMEGA32 TDA7313 A lot of work in the ATmega32 occur when
project featuring a beautiful rose amp amp volume control on the floor in the TDA7313 TDA7294 is used in the upgrade
process. Digital FM radio... Electronics Projects,Multifunction Digital Amplifier Project TDA7294 ATmega32 TDA7313 "avr
project, microcontroller projects, tda7294…... Listed under: Sound - Audio Projects
505. FT232R USB I-O CIRCUIT ATMEGA88 USB I / O circuit ATMEGA88 based on the usb connection FT232R is done via detailed ir
project ( German explanation ) the C source code, circuit diagrams and PCB drawing of the picture... Electronics
Projects,FT232R USB I-O Circuit ATMEGA88 "avr project, microcontroller projects, " USB I /…... Listed under: Interfacing(USB -
506. 0-30V REGULATED DIGITAL SWITCHING POWER SUPPLY ATMEGA8 LM2576ADJ Very high quality design of the digital power
supply circuit. Voltage current of 2 × 16 lcd display of the beauty and power of the switching mode operation switching
DCDC Madden LM2576 ADJ (adj... Electronics Projects, 0-30V Regulated Digital Switching Power Supply ATmega8
LM2576ADJ "atmega8 projects, avr project,…... Listed under: Development Board - Kits Projects
507. TOY CAR MODIFICATION MADE SIMPLE ROBOT PROJECT ATTINY2313 Simple robot project ATtiny2313 microcontroller used
robot body for a cheap remote controlled toy car is made up of the robot’s four sides LED sensors placed somewhere when it
hit the back çekliy direction...Electronics Projects, Toy Car Modification Made Simple Robot Project ATtiny2313 "avr project,
microcontroller projects, "…... Listed under: Car Projects, Robotics - Automation Projects
508. REMOTE CONTROLLED PROPELLER CLOCK CIRCUIT AT90S2313 Before air time, “Propeller Clock” projects I shared in this
project control and mode selection can be achieved in both analog clock and digital clock view modes control for the Sony
control protocol used... Electronics Projects, Remote Controlled Propeller Clock Circuit AT90S2313 "avr project,
microcontroller projects, " Before air…... Listed under: Clock Projects
509. LIPO LI-ION BATTERY CHARGER CIRCUIT BALANCING ATTINY26 Attiny26 microcontroller based on the charging circuit has a
lot of features in a single package 3l 12.6V LiPo batteries and Li-ion batteries and battery charging voltage edebiliry balanslıy
regulate temperature, timing, voltage and... Electronics Projects, Lipo Li-ion Battery Charger Circuit Balancing ATtiny26 "avr
project, battery charger circuit,…... Listed under: Battery Projects
510. ZENER DIODE TEST CIRCUIT VOLTAGE INDICATOR ATMEGA8 Interestingly circuited actually zener diode test measuring
instruments should have a property zener measurement of when you are secure, a voltage see better, but so far no
measuring instruments equipped with this feature I... Electronics Projects, Zener Diode Test Circuit Voltage Indicator
ATmega8 "atmega8 projects, avr project, microcontroller…... Listed under: Metering - Instrument Projects
511. REMOTE CONTROLLED ROBOT CIRCUIT RC5 AT90S2313 The robot’s control AT90S2313 microcontroller provided with the
processor 4MHz is operated for control rc5 protocol that uses a control used robot çalışmala for 4 pcs 2200mAh NiMH
batteries used for the experiment alkaline... Electronics Projects, Remote Controlled Robot Circuit RC5 AT90S2313 "avr project,
microcontroller projects, " The robot’s…... Listed under: Robotics - Automation Projects

512. LINE FOLLOWING ROBOT PROJECT ULTRASONIC SENSOR CIRCUIT ATMEGA16 CNY70 SFR05 Quite a different line following
robot project was already in school competition designed for the author as he could a nice job exposes the robot’s
appearance sumo robots similar to healthy controls ATMega16 microcontroller... Electronics Projects, Line Following Robot
Project Ultrasonic Sensor Circuit Atmega16 CNY70 SFR05 "avr project,…... Listed under: Robotics - Automation Projects
513. NI-MH BATTERY CHARGER CIRCUIT ATMEL ATTINY26 Ni-MH Battery Charger circuit 4 AA batteries can be charged in the
circuit is more complex, but in general attiny26 microcontroller circuits BD140 transistors and a few passive components
consist of batteries connected to... Electronics Projects, Ni-MH Battery Charger Circuit Atmel ATtiny26 "avr project, battery
charger circuit,…... Listed under: Battery Projects
514. ROBOTIC DOG PROJECT, 16 CHANNEL SERVO CONTROL PROGRAM Prepared with great effort as a hobby project “robot
dog” very detailed, especially the mechanical portion control, etc. rc5 remote control computer. has features such as control
solid Atmel ATmega32 and ATMEGA8515 based on... Electronics Projects, Robotic Dog Project, 16 Channel Servo Control
Program"avr project, microcontroller projects, "…... Listed under: Robotics - Automation Projects
515. 64 LED PROPELLER EFFECT CIRCUIT ATMEGA8 Led effect circuit 64 leds LEDs on the printed circuit board disposed in the
impeller has a very different effect. A plurality of circuit components used SMD type. Effects displacement, velocity pcb solder
buttons...Electronics Projects, 64 Led Propeller Effect Circuit ATmega8 "atmega8 projects, avr project, led projects,…... Listed
under: LED Projects
516. BLUETOOTH JOYSTICK CONTROLLED DISCOVERY ROBOT PROJECT Very detailed advanced robot project for many of us not
be implemented, but the code, schematics, methods different robot project can be used in reconnaissance robot via mobile
phone blutut can be manipulated by...Electronics Projects, Bluetooth Joystick Controlled Discovery Robot Project "avr project,
microcontroller projects, " Very detailed…... Listed under: Robotics - Automation Projects
517. MCP4725 DAC AVR ATmega library The MCP4725 DAC is a pretty common and cheap single channel 12 bit buffered voltage
DAC, it also has an onboard EEPROM. To drive this chip we can use I2C interface. The ATmega8 used for my implementation
has an embedded I2C interface, so we just can use that interface.…... Listed under: Development Board - Kits Projects
518. Switch debounce library Contact bounce (ref. https://en.wikipedia.org/wiki/Switch#Contact_bounce) is a common problem
with mechanical switches and relays. Switch and relay contacts are usually made of springy metals. When the contacts strike
together, their momentum and elasticity act together to cause them to bounce apart one or more times before making
steady…... Listed under: Development Board - Kits Projects
519. ATmega32 ADC for Light and Temperature Sensors This tutorial shows how to implement the Analogue to Digital
Converter (ADC) function on ATMega32 using C code. It consists of code examples, and the meaning of some nomenclature
such as sampling rate, and resolution. However before we get to the code, let us start from the…... Listed under: Sensor -
Transducer - Detector Projects, Temperature Measurement Projects
520. RTTTL Player for the ATmega32 Ring Tone Text Transfer Language (RTTTL) is a simple text-based code for recording monophonic musical tones. The
script is usually loaded into a mobile phone, which is able to convert the code to equivalent musical notes. Many early phones had an integrated
RTTTL player, which played…... Listed under: Game - Entertainment Projects
521. Connecting Piezo Speaker to ATmega32 An ATMega32 sound generator code is extremely simple to implement. Almost any
GPIO pin can drive a piezo buzzer, and the output quality is fine for producing some beeps. The code shown here is the
simplest one I remember using basic physics, and since it…... Listed under: Sound - Audio Projects
522. PHONE CONTROLLED MOBILE ROBOT CIRCUIT MT8870 ATMEGA16 Wireless, remotely controlled applications quite popular
in this project through the mobile phone robot control is done the robot on the Nokia 1100 mobile phone used phone
signals from the MT8870 receiver DTMF decoder... Electronics Projects, Phone Controlled Mobile Robot Circuit MT8870
ATMega16 "avr project, microcontroller projects, " …... Listed under: Robotics - Automation Projects
523. 4 CHANNEL PWM CONTROL CIRCUIT VISUAL BASIC RS232 AT89C2051 PWM control project software source code in Visual
Basic and are prepared (linux, windows) via RS232 serial port (19200 Baud) AT89C2051 microcontroller based on the 4-
channel PWM control circuit can be made. PWM output... Electronics Projects, 4 Channel PWM Control Circuit Visual Basic
RS232 AT89C2051"avr project, microcontroller…... Listed under: Development Board - Kits Projects
524. NOKIA5110 LCD LOGIC ANALYZER CIRCUIT ATMEGA8 Built on the atmega 8 microcontroller Logic Analyzer circuit for nokia
5110 display lcd display kullanılanılıyor crafted with AVRstudio Software four. source software insurance settings schema, pcb,
etc. files. Frequency capture 400 kHz, Max... Electronics Projects, Nokia5110 LCD Logic Analyzer circuit ATmega8 "atmega8
projects, avr project, microcontroller projects, "…... Listed under: LCD Projects

525. ADJUSTABLE POWER SUPPLY CIRCUIT 0 30V LCD Power supply circuit consists of a few sections 04 to 0 30v power supply
based on solid TL081 op amp circuit 2N3055 power transistor quite popular and a classic by many people applied.
LCD... Electronics Projects,Adjustable Power Supply Circuit 0 30V LCD "atmega8 projects, avr project, microcontroller…... Listed
under: LCD Projects
526. SYNTHESIZER CIRCUIT AT89S53 AT89S52 Musicians use a variety of sound-producing device “Synthesizer” When you are
setting a very good quality work is making. AT89S52 and AT89S53 Synthesizer used in the project on the LFO, ENV FILTER,
OSC, MIX...Electronics Projects, Synthesizer Circuit AT89S53 AT89S52 "avr project, microcontroller projects, " Musicians use
a…... Listed under: Sound - Audio Projects
527. WAVE READER CIRCUIT AT89S52 FLASH MEMORY PIC24, 32, MSP430 is progressing rapidly but AT89S52 time, I still made

sure that what is in use by 8051. In this project, kingston 8gb flash memory is read in the wav files (wav... Electronics
Projects, Wave Reader Circuit AT89S52 Flash Memory "avr project, microcontroller projects, " PIC24,…... Listed under: Sensor
528. WITH PELTIER MINI REFRIGERATOR CIRCUIT ATMEGA8 DS18S20 Peltier Thermoelectric Cooler Is how it works with 12-Volt
Feed information and 50W Peltier Mini Fridge built on the lcd display after the ATmega8 microcontroller from a more
advanced peltier control circuit. The value...Electronics Projects, With Peltier Mini Refrigerator Circuit ATmega8
DS18S20 "atmega8 projects, avr project, microcontroller…... Listed under: Home Automation Projects
529. S65 SIEMENS LCD EXAMPLES CIRCUIT ATMEGA16 ATMEGA32 Before “Siemens S65 LS020 glcd ATmega128 AVR” shared
examples of implementation through a lot of similar projects with ATmega16 ATmega32, microcontrollers. A few of them;
Image via representation of FAT16 MMC card color, font... Electronics Projects, S65 Siemens LCD examples Circuit ATmega16
ATmega32 "avr project, microcontroller projects, " …... Listed under: LCD Projects
530. PT100 SENSOR THERMOSTAT CIRCUIT ATMEGA8 Thermostat circuit for 2 pt100 temperature measurement used atmega8
mikrüdenetleyici sensor pt100 sensors gives the circuit output is being used according to the information received. The
thermostat is located on the circuit board led... Electronics Projects, PT100 Sensor Thermostat Circuit ATmega8 "atmega8
projects, avr project, microcontroller projects, " Thermostat…... Listed under: Sensor - Transducer - Detector Projects
531. EXCELLENT LED BALL CIRCUIT ATMEGA88 Great design has been providing birthday gifts as does not prepare mention Led to
control atmega88 microcontroller is used ports çoklayıp LEDs milk to 74HC595 used LEDs effect has been very welcoming
approximately 256... Electronics Projects, Excellent Led Ball Circuit ATmega88 "avr project, led projects, microcontroller
projects, " Great…... Listed under: LED Projects
532. USB PASSWORD GENERATOR CIRCUIT ATTINY85 Attiny85 not found on the USB module to work, but as software optimized
circuit when connected to a computer mouse USB HID is known as pull-up resistors on the circuit has very few
ingredients... Electronics Projects, USB Password Generator Circuit ATtiny85 "avr project, microcontroller projects, "
Attiny85 not found…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
533. MECHANICAL CLOCK CIRCUIT ATMEGA8 In fact, what lies At the forefront of the digital but mechanics should have been a
wonderful project:) is an interesting time in the atmega8 microcontroller time and when the mind comes to the... Electronics
Projects, Mechanical Clock Circuit ATmega8 "atmega8 projects, avr project, microcontroller projects, " In fact,…... Listed under:
Clock Projects
534. DIGITAL RADIO CIRCUIT TEA5767 AT89S8253 TEA5767 is a digital radio, especially mp3 and fm radio module @ETE before
“TEA5767 Pic16f628 Digital PLL-controlled FM radio receiver system” article is controlled with the Pic16f628 microcontroller
used in this project, the radio... Electronics Projects, Digital radio circuit TEA5767 AT89S8253 "avr project, microcontroller
projects, " TEA5767 is a…... Listed under: Radio Projects
535. ULTRA SONIC CLEANER ROBOT CIRCUIT L298 AT89C2051 AT89C2051 microcontroller used in robot motor drive for cleaner
L298 dual H-bridge driver IC is used 40 kHz ultra sonic senrörler (multicomp sq-40-t-10b) to detect and to change direction
with the bodies, continues to...Electronics Projects, Ultra Sonic Cleaner Robot Circuit L298 AT89C2051 "avr project,
microcontroller projects, " AT89C2051…... Listed under: Robotics - Automation Projects
536. USB BUSINESS CARD WITH ATTINY85 Attiny85 Atmel microcontroller with USB Business Card project established quite
interesting circuit with very few elements attiny85 16.5 MHz internal RC oscillator frequency used. USB connector on the USB
socket on the PCB designed... Electronics Projects, USB Business Card with attiny85 "avr project, microcontroller projects, "
Attiny85 Atmel…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects

537. ATMEGA88 IR2184 DC SERVO MOTOR DRIVER CIRCUIT DC Servo motor driver circuit based on the microcontroller atmel
atmega88 outputs half bridge driver IC Ir2184 is being used with this integrated works at a frequency of 16MHz DC servo
Irf540 MOSFETs atmega88... Electronics Projects, Atmega88 IR2184 DC Servo Motor Driver Circuit "avr project, dc dc
converter…... Listed under: Motor Projects
538. LINE FOLLOWING ROBOT SUMO ROBOT, CONTROL CIRCUITS Sumo, Line following and robot control card project open
source design and very high quality of all resources provided PIC microcontroller code and eagle diagram pcb drawings are
especially line following robot prepared for... Electronics Projects, Line following Robot Sumo Robot, control circuits "avr
project, microcontroller projects, " Sumo,…... Listed under: Robotics - Automation Projects
539. ATMEL LED MULTI-FUNCTION DISPLAY ATMEGA32U4 WATCHES Atmel microcontroller Board with Led indicator wristwatch
ATmega32U4 project there is no usb connection and SD card connection, the advanced charging system, piezo sensor, etc.
are included in the design of printed circuit boards... Electronics Projects, Atmel LED Multi-Function Display ATmega32u4
Watches"avr project, microcontroller projects, " Atmel…... Listed under: LED Projects
540. SIM900 MODULE PCB AVR APPLICATIONS Simcom Sim900 GSM module produced by the company prepared for the PCB
module and ATMEGA32 microcontroller based on Nokia 3310 lcd display GSM module for remote control application
SIM900D (place of origin: CN; proteus... Electronics Projects, SIM900 Module PCB AVR Applications "avr project,
microcontroller projects, " Simcom Sim900…... Listed under: Phone Projects
541. GUITAR TUNING PROJECT WITH ARDUINO UNO Arduino Uno kit on the Board at the entrance of the TL082 opamp used
Guitar Tuning circuit audio audio input and frequency to detect the “Arduino-Frequency-Detection” software used. According
to the LEDs light at... Electronics Projects, Guitar Tuning Project with Arduino Uno "arduino projects, avr project,
microcontroller projects, "…... Listed under: Sound - Audio Projects
542. ARDUINO UNO WITH INTERESTING CLOCK PROJECT I’ve shared this with different time interesting projects carried out with
the Arduino Uno this time, I think the most interesting thing isn’t debatable kullanışlımı project but the idea as a different
kind of... Electronics Projects, Arduino Uno With Interesting Clock Project "arduino projects, avr project, microcontroller
projects, "…... Listed under: Clock Projects
543. ATMEGA32 PCB DRILL MACHINE This document describes the construction of a PCB drill machine driven by a master-
controller board and three stepper motor driver boards. These four single sided PC boards each contain an Atmega16/32
microcontroller. Communication between... Electronics Projects, ATMEGA32 PCB drill machine "avr project, microcontroller
projects, " This document describes the…... Listed under: CNC - Printing Machines Projects
544. PORTABLE RF JAMMER CIRCUIT ATMEGA48 So far I have ever seen , tidy and with all the resources shared jammer circuit
project design, it’s very smart Sizes also pretty small pocket on the internet a lot jammer circuit ,... Electronics
Projects, Portable RF Jammer Circuit ATmega48 "avr project, microcontroller projects, " So far…... Listed under: Sensor -
545. WINAMP REMOTE CIRCUIT BLUETOOTH AT90USB1287 NOKIA LCD LMX9838 A very detailed report of a project is already
included in the schema. The author of the thesis, the eagle pcb source code etc. everything. The circuit used the main parts
AT90USB1287 LMX9838 (Bluetooth... Electronics Projects, Winamp Remote Circuit Bluetooth AT90USB1287 Nokia LCD
LMX9838 "avr project, microcontroller projects, "…... Listed under: Other Projects
546. BATTERY ALARM CIRCUIT FOR MODEL HELICOPTERS ATTINY13 ATTINY13 Atmel microcontroller installed on the circuit
model helicopter is checking the voltage of the battery the battery (or battery) voltage circuit when the level set LEDs, buzzer,
giving the alam. ATTINY13 PB2, PB1,... Electronics Projects, Battery Alarm Circuit for Model Helicopters ATtiny13 "avr project,
microcontroller projects, simple…... Listed under: Battery Projects, Circuits, Clock Projects
547. ATMEL ATTINY45 BLUETOOTH SCOREBOARD CIRCUIT The scoreboard circuit is based on Atmel microcontroller ATtiny45
circuit cell phone can be controlled via bluetooth. The bluetooth module used in the indicator circuit BTM400-6B is an LCD
TV has VGA output of...Electronics Projects, Atmel ATtiny45 Bluetooth Scoreboard Circuit "avr project, microcontroller
projects, " The scoreboard circuit is based…... Listed under: Circuits
548. ATMEGA8 USB EMAIL NOTIFIER CIRCUIT Market “USB Mail Notifier” ready devices are sold, but in practice, ileginç project
also ATmega8 microcontroller and the email account that connects the program’s source code (C + + RAD studiox) or not
different... Electronics Projects, ATmega8 USB Email Notifier Circuit "atmega8 projects, avr project, microcontroller projects, "
…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
549. MULTI-FUNCTION DIGITAL WRISTWATCH CIRCUIT ATMEL ATMEGA168PA Digital clock project PCB design is very good and prepared and used
according to the coffers of small metal wristwatch. Except for a few digital Wristwatch circuit material including all the elements of SMD...Electronics

Projects, Multi-function Digital Wristwatch Circuit Atmel ATmega168PA "avr project, microcontroller projects, " Digital
clock…... Listed under: Clock Projects
550. DIGITAL CLASS D AMPLIFIER PROJECT TAS5613 TDA9859 ATMEGA128 TDA9859 The main part of the preamplifier is an
integrated circuit TDA9859, this integrated circuit is controlled via the I2C microprocessor Atmega128. Individual settings of
the preamplifier through the keyboard are displayed on the... Electronics Projects, Digital Class D Amplifier Project TAS5613
TDA9859 ATmega128 "audio amplifier circuits, avr…... Listed under: Sound - Audio Projects, Uncategorized
551. DIGITAL CLASS D AMPLIFIER CIRCUIT TAS5706A PCM1850A ATMEGA128 TAS5706A Class D Amplifier was itself the signal
processor. From this parts depend all the other elements. Has an impact on the type of power supply, the control method of
the type converter. That... Electronics Projects, Digital Class D Amplifier Circuit TAS5706A PCM1850A ATmega128 "audio
amplifier circuits, avr…... Listed under: PWM Projects
552. 0-30V 0-3A ADJUSTABLE SWITCHING LABORATORY POWER SUPPLY DC-DC Laboratory Power Supply 0-30V 0-3A LT1074 is a
switching regulator type step-down (lowering) with a maximum current of 5 A. Can work with the value of the input voltage
up to 60 V... Electronics Projects,0-30V 0-3A Adjustable Switching Laboratory Power Supply "avr project, dc dc converter…...
553. 240W ELECTRONIC BALLAST CIRCUIT IR2104 ATMEGA48 CONTROLLED IR2104 240W Fluorescent tube Ballast Circuit. Work
was designed an electronic ballast for starting six fluorescent lamps with a total output of 240W with integrated dimming-
controlled analog input and button. Priority is set to... Electronics Projects, 240W Electronic Ballast Circuit IR2104 ATmega48
Controlled"avr project, microcontroller projects, power…... Listed under: Circuits
554. 1A 10A ADJUSTABLE BATTERY CHARGING CIRCUIT 100AH Atmel ATTINY24 microcontroller based automatic battery charger
circuit can charge 12V batteries with different power on (1A…10A current setting range of the charging current with limitation
10Ah, 20Ah, 30Ah, 40Ah, 50Ah, 60Ah, 70Ah, 80Ah,... Electronics Projects, 1A 10A Adjustable Battery Charging Circuit
100Ah "avr project, battery charger circuit,…... Listed under: Battery Projects
555. 230V FAN REGULATOR CIRCUIT MOSFET MC33152 ATTINY25 Brushless asynchronous motors, with compact rotor windings,
called short cages, are used to drive different fans. Their advantages are durability and simple construction. The presented
layout uses a certain characteristic of such a fan... Electronics Projects, 230V Fan Regulator Circuit Mosfet MC33152
ATtiny25 "avr project, microcontroller projects, power…... Listed under: Circuits
556. THERMOMETER HYGROMETER CIRCUIT USB DHT22 ATMEGA8 The presented layout is a snap on a computer for measuring
DHT22 temperature and humidity. It measures the temperature from -40 to 80 ° C with a resolution of 0.1 ° C and
accuracy... Electronics Projects,Thermometer Hygrometer Circuit USB DHT22 ATmega8 "atmega8 projects, avr project,
microcontroller projects, "…... Listed under: Metering - Instrument Projects
557. PROGRAMMABLE TIMER CIRCUIT ATTINY25 ATtiny25 Programmable Timer To describe the operation of the device, we will
use an example – control of the electromagnetic bolt mounted in the wicket. In the simplest version we require that the
push... Electronics Projects, Programmable Timer Circuit ATtiny25 "avr project, microcontroller projects, " ATtiny25
Programmable Timer To describe…... Listed under: Clock Projects
558. TINY USB PROGRAMMER AVR MICROCONTROLLERS AVRDUDE USB programmer There are few components – the ATtiny45
microcontroller, two Zener diodes, a capacitor and several resistors. Of course, there are still connectors – USB plug and IDC-
6 plug. Resistor R1 informs host... Electronics Projects, Tiny USB programmer AVR microcontrollers AVRDUDE "avr project,
microcontroller projects, programmer circuit, "…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
559. ATMEGA48 TIMER TRIGGERED BY CURRENT FLOW ASM-010 ATMEGA48 Many devices may be in standby mode during
downtime. They do not perform any work, they are apparently disabled, but the control circuits are powered. To extract
useful information from the point of...Electronics Projects, ATMEGA48 Timer triggered by current flow ASM-010 "avr project,
microcontroller projects, power…... Listed under: Clock Projects
560. Ultrasonic Radar Model Using Microcontroller ATmega128 The circuit described here demonstrates the working of a radar system. It uses ultrasonic
waves to detect an object and measure its distance and angular position, and displays the same on a 20x4 LCD screen. -- Ashutosh M. Bhatt is an M.
Tech in embedded…... Listed under: Sensor - Transducer - Detector Projects

561. Digital Soil Moisture Meter A digital soil moisture meter is used for indicating the water content of a given soil sample. As
crop production requires water at different stages and in different amounts, it is important to measure soil moisture from
time to time to know its status. The…... Listed under: Metering - Instrument Projects
562. NIXIE TUBE THERMOMETER CIRCUIT Nixie lamp Thermometer DS18B20 Circuit with ATtiny2313 The first Nixie lamps
appeared in the mid-twentieth century. For many years they have been used in a variety of apparatuses but have been
supplanted by newer... Electronics Projects, Nixie Tube Thermometer Circuit "avr project, microcontroller projects, " Nixie
lamp Thermometer DS18B20 Circuit…... Listed under: Metering - Instrument Projects
563. ATMEGA8 FT232R USB ESR METER CIRCUIT USB ESR Meter Circuit The main part of the meter is a ATmega8 microcontroller
that controls the entire device. Its main the task is to process measured data and perform calculations so that
the... Electronics Projects, ATmega8 FT232R USB ESR Meter Circuit "atmega8 projects, avr project, microcontroller
projects, "…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
564. ATMEL ARDUINO COLORED CONNECTION CHART Projects or schematics, drawings that will work when preparing pcb Atmel
AVR Microprocessors Information Tags for “Share” drawings directly on Atmel microcontrollers. Colored linking expansions
are more comprehensible for those dealing with Atmel Series... Electronics Projects, Atmel Arduino Colored Connection
Chart "arduino projects, " Projects or schematics, drawings that…... Listed under: Circuits
565. AUTOMATIC FEEDING MACHINE WITH CD-ROM MECHANIC For the author, the automatic feeding machine for the wedge is
the easiest mechanical part for the application. they insert a plastic container all of which is placed on the CD present on
the… Electronics Projects, Automatic Feeding Machine With CD-ROM Mechanic “avr project, microcontroller projects, “ For…...
566. Avr Atmega8 Microcontroller – An Introduction In my previous article, I’ve discussed about ATmega32. Now, let me introduce
another member of AVR microcontroller family, the ATmega8. This member has many features similar to that of ATmega32.
But it has reduced number of features and capabilities, yet it has enough features to…... Listed under: AVR ATmega Projects
567. Handling the Digital Input Output in AVR Micro Controllers I have already discussed about a few chapters necessary to get
into AVR programming. Now this is the first article that deals with programming. Let us start with the basics. Digital input
output (I/O) is the basic feature supported by AVR micro controller. To facilitate…... Listed under: LED Projects
568. Standard Library & String Formatting for AVR Here in this article, I am planning to brief you through the Standard library of
AVR-GCC. By the term “Standard Library” we mean the “Standard header” files like “stdio.h”, we commonly see in C
programming language. Have you ever used String Formatting in ANSI C?…... Listed under: AVR ATmega Projects
569. Frequency counter circuit Simple Frequency Counter You may have already seen various projects over many websites named
Frequency counter, Digital Frequency Counter etc. I’m posting just another of them. Showing the use of timer/counter of AVR
micro controller (Atmega8) in one of it’s form. This circuit can be…... Listed under: LCD Projects

570. How to Work With 32K crystal and AVR Microcontroller This article teaches you how to add 32K external crystal source to
AVR micro controller (Atmega8 ) with circuit diagram & C program. Introduction Timing-is one of the basic function,
performed by the micro controllers. Every microcontroller has at least one timer/counter module in its…... Listed under: AVR
ATmega Projects
571. How to work with the ADC unit of an AVR Micro-controller Introduction The first step to digital signal processing is to
convert a signal into digital data, and here the Analog to Digital Converter devices comes into action. Some of the AVR micro
controllers include ADC unit in their features. This is a very useful unit…... Listed under: Security - Safety Projects
572. Interfacing LCD Module with AVR in 4-Bit Mode This article is another step forward in learning more about AVR
microcontrollers. We have demonstrated interfacing of LCD module with ATmega328 microcontroller, which will help you to
learn its basic concepts. ATmega328 is an eight bit AVR (Advanced Virtual RISC) based microcontroller. It is a…... Listed under:
LCD Projects
573. Bluetooth Home Automation using AVR and Android App DIY-Bluetooth based Home Automation Project In this project, let’s
see how to design a Bluetooth based home automation project.This article explains the steps involved in the designing of a
Bluetooth home automation kit, starting from the configuration of a Bluetooth module. The article also explains…... Listed
under: Android Projects
574. Keypad Door Lock using AVR Microcontroller – Atmega16 Password Based Keypad Door Lock In this article, a digitally
secured lock based on password verification is explained. The system uses a seven segment display array to show the
password, a matrix keypad to enter the numbers/password and operates a relay (to activate the solenoid…... Listed under:
575. MultiPurpose Atmel Development Boards Project Atmel series microcontrollers series to prepare for the software quality
testing to ensure ease in your test circuit has 3 different test circuit. ATmega8, ATMega16, atmega162, ATtiny2313 and
ATTINY13 made

to the circuit RS232... Electronics Projects, MultiPurpose Atmel Development Boards Project "avr
development board, "…... Listed under: Development Board - Kits Projects
576. ATmega16 Analog-Looking Digital Clock Project Atmega16 microcontroller in our circuit monitor 7 inch in size. Screen “3
inch” or “4 inch” may be, it doesn’t matter. We have the biggest screen by controlling the foot links we could find....
Electronics Projects, ATmega16 Analog-Looking Digital Clock Project "avr project, microcontroller projects,…... Listed under:
Clock Projects
577. Make Your Own WiCard WiFi Module on a Breadboard Like Arduino you can make your own WiCard on a breadboard. All
you need are resistors, capacitors, breadboard, wires, ATmega8, and ESP8266. Story Like “Arduino," you can make your own
WiCard on a breadboard. If you want to make WiCard on a breadboard before making…... Listed under: AVR ATmega Projects
578. Interfacing HC-05 Bluetooth module with AVR Microcontroller In this tutorial let us learn How to interface HC-05 Bluetooth
Module with AVR ATmega8 microcontroller. We will establish communication between Android mobile and Atmega8 through
Bluetooth module which takes place through UART serial communication protocol. In this project we will control a LED using
Bluetooth…... Listed under: Phone Projects
579. Interfacing RF module with Atmega8: Communication between two AVR Microcontrollers Making our projects Wireless
always makes it to look cool and also extends the range in which it can be controlled. Starting from using a normal IR LED for
short distance wireless control till an ESP8266 for worldwide HTTP control, there are lots of ways…... Listed under: LED
Projects
580. Interfacing GSM Module with AVR Microcontroller: Send and Receive Messages GSM modules are interesting to use
especially when our project requires remote access. These modules could make all actions that our normal mobile phone
could do, like making/receiving a call, sending/receiving a SMS, connecting to internet using GPRS etc. You can also connect
a normal microphone…... Listed under: Phone Projects

581. UV Sensor ML8511 AVR Atmega library Ultraviolet (UV) is an electromagnetic radiation with a wavelength from 10 nm to 400
nm. The ML8511 is an ultraviolet sensor that output an analog signal correlated to the amount of UV light detected. By
datasheet the sensor detects wavelength from 280nm to 560nm. Here…... Listed under: Sensor - Transducer - Detector
Projects
582. Using AVR Studio – My first C++ code This is an extremely simple "Hello World" C++ code for the ATMega32 that you can
follow using AVR Studio. You do not need any hardware such as the chip or even the ISP programmer cable because AVR
Studio simulates the inputs and outputs, and you…... Listed under: LED Projects
583. Power factor measurement using Atmel AVR Micro-Controllers To learn about the power factor measurement, you should
have a basic knowledge of power factor. There are three types of loads. Resistive Inductive Capacitive When we apply AC
voltage to resistive loads it will not change the current wave form. But inductive loads will…... Listed under: LCD Projects
584. Auto No Break Power Supply Control The major aim of this no break power supply project is to supply continuous energy
supply to a load, by picking the supply from any spring out of the four like – generator, mains, inverter and solar robotically
in the lack of any of the…... Listed under: LCD Projects
585. DC motor interfacing with AVR ATmega16/ATmega32 DC motor converts electrical energy in the form of Direct Current into
mechanical energy. In case of motor, the mechanical energy produced is in the form of rotational movement of the motor
shaft. The direction of rotation of the shaft of the motor can be…... Listed under: Motor Projects
586. ATmega8 Line Follower Robot (LFR) Project – Part 2/2 Now that the mechanical assembly part is over,and we have completed
the construction of left and right (L&R) infrared sensor cards. Since the MCU (ATmega8) cannot drive the dc motors directly, a
dedicated motor driver circuit is used. The motor driver circuit here is based…... Listed under: Robotics - Automation Projects
587. A digital DC powersupply Introduction In 2002 I wrote a linuxfocus.org article about a Microcontroller based DC powersupply
(LF November2002 article251) The article received a lot of interest as I noticed from emails which I received on this subject.
The design of this powersupply was however something for advanced…... Listed under: LED Projects
588. An NRF24L01+ and FTDI Ready Atmega 328P-PU (3.3V, 500 MA) Microcontroller With Dual Power Capability, Undervoltage, Hysteresis, and Thyristor-
Crowbar Overvoltage Protection This board is designed to safely drive a 3.3V microcontroller and connected accoutrements.
It supports primary and backup power sources and provides numerous over and under voltage safeguards. The
microcontroller here is a bare-bone, no-frills Atmega 328P-PU with no leds, driven by a 16 MHz…... Listed under: Battery
Projects
589. AVR-based Sensor Keyboard A modern microcontroller has almost everything that's needed to implement a touch sensor
matrix. There are several sensing technologies: IC manufacturers typically advise using certain tech, sometimes they offer
ready to use hardware- or software-based solutions. I was curious to try to implement a sensor…... Listed under: AVR ATmega
Tutorial, Sensor - Transducer - Detector Projects
590. Arduino LFO Waveform Generator V2 Introduction This project uses an Arduino microprocessor and a MAX522 8 bit serial
DAC to produce arbitrary low frequency oscillator (LFO) waveforms. These waveforms are useful for driving a tremolo/vibrato
circuit in a guitar amplifier such as the Lil Tiger or the Hammonator 2RVT. This…... Listed under: Motor Projects
591. Programming ATMEGA32 (or Any Other AVR) Using Arduino IDE The Arduino is a very cool development board where you
could create hundreds of projects. But it doesn't mean that for every project you create, you would need an Arduino board
dedicated to that project alone. A hundred projects and a hundred Arduinos? That's a…... Listed under: Android Projects, AVR
ATmega Tutorial
592. AVR ATmega32 Mini Development Board – Interfacing LCD AVR ATmega32 Mini Development Board is interfaced with a LCD
module (2×16) operating at 5V. The voltage at the third pin of the LCD can be varied by potentiometer to adjust contrast.
LCD can work either in 4 or 8 bit mode. Here, the circuit is…... Listed under: LCD Projects
593. Interfacing Ultrasonic Rangefinder with AVR MCUs – AVR Tutorial Obstacle detecting sensors are one of the most basic type of sensors that electronic
hobbyists use. There are several methods to make cheap obstacle sensors. These simple sensors are made using a IR Rx/Tx pair or Normal LED and
LDR pair(this design is most basic…... Listed under: Android Projects, Development Board - Kits Projects

594. How to control DC motor speed using PWM on Atmega32 Using PWM (Pulse Width Modulation) to control a device is a
common practice in embedded systems; for example, you can use it to control the light intensity of a LED or control the
speed of a DC motor. In this article, we will explain how to…... Listed under: Motor Projects, PWM Projects
595. Servo Motor Control by Using AVR ATmega32 Microcontroller Servo motors are a type of electromechanical actuators that do
not rotate continuously like DC/AC or stepper motors, rather they used to position and hold some object. They are used
where continuous rotation is not required so they are not used to drive wheels (unless…... Listed under: Microcontroller
Programmer Projects, Motor Projects
596. Atmel ATmega Video generator with SDRAM This projects uses 8MByte SDRAM from a 168 pin DIMM SDRAM and generates
videosignal for a VGA monitor with a resolution of 512x480 pixels with 256 colors at 60Hz using mega8515. The project uses
burst mode of SDRAM, which can feed up to 512 bytes…... Listed under: AVR ATmega Tutorial, Microcontroller Programmer
Projects
597. How to make Automatic Charger for a 7Ah Battery 7Ah Sealed Lead Acid Battery 7Ah Sealed lead acid battery is a very
popular battery which people use in most places like fans, LEDs etc. The reason behind popularity of 7Ah battery is due to its
medium size and medium Ah rating. By medium means,…... Listed under: Battery Projects
598. hd44780 Character LCD Displays – Part 2 Introduction This tutorial continues from Character LCD Displays – Part 1. In this part
we will connect the LCD module to an Atmega8 microcontroller, then write some code to drive it. The Circuit Our first task is
to build the circuit. We will be using…... Listed under: LCD Projects
599. First steps with micro controllers (ATMega8) Purpose of this article: 1) to learn how to connect the Micro controller in a
simple circuit and how to power it 2) to see how to create a simple programmer (a device to connect the micro controller to
a PC for uploading software) 3)…... Listed under: AVR ATmega Tutorial, Development Board - Kits Projects, LED Projects
600. Minimal Arduino with ATmega8 Like me, you may have a few old Arduino boards or ATmega8 chips (in the boards) laying
around from when you were first playing with Arduino. Those chips can still be really useful as the heart of a tiny “Minimal
Arduino” setup. A normal Arduino…... Listed under: Android Projects, Circuits, Other Projects
601. Atmega8 based Voltmeter Ampmeter v2 Low power consumption Better Amperes display resolution while using low value
drop resistor. Much smaller PCB size, only 5cm x 5cm. Still no SMD components. Easy calibration, only one voltage adjust and
one ampere adjust preset, no voltage out detection. Voltage supplied by my 12Volt…... Listed under: AVR ATmega Tutorial,
602. Micro-controller Programming on a Bread Board In playing around with DIY electronics, Pugs has developed enough
confidence to share his knowledge with his juniors. So, in one such occasion, he decided to give a try to program a micro-
controller, as part of the electronics hobby club. There have been many hobbyist…... Listed under: Battery Projects
603. Nokia5110 graphical display interfacing with AVR ATmega16/ATmega32 Introduction Nokia5110 is a graphical display that
can display text, images and various patterns. It has a resolution of 48x84 and comes with a backlight. It uses SPI
communication to communicate with a microcontroller. Data and commands can be sent through microcontroller to the
display…... Listed under: Phone Projects
604. Configuring and using XBEE wireless modules Xbees are some of the most powerful wireless modules you can find and they’re also very easy to
configure and use. The only thing is they cost about Rs.1000 to Rs.2500 depending on the range and other parameters. If you’re like me and only
bought…... Listed under: AVR ATmega Tutorial, LCD Projects, Microcontroller Programmer Projects

605. The simplest digital voltmeter with AVR This is probably the simplest possible digital voltmeter with Atmel AVR
microcontroller. The circuit is controlled by a microprocessor IO1 - Atmel AVR ATmega8 (ATmega8, ATmega8L), a program to
download and configuration bits setting is below. (ATmega8 may seem too "big", but was chosen because…... Listed under:
AVR ATmega Tutorial, Clock Projects, Electronics News Updates, LED Projects
606. Input Devices Measure something: add a sensor to a microcontroller board that you have designed and read it. This week I
decided to make ATMEGA 328 board. ATMEGA 328 Some of the Features of ATMEGA 328 are 1.8-5.5V operating range Up to
20MHz 32kB Flash program memory…... Listed under: AVR ATmega Tutorial, Microcontroller Programmer Projects, Sensor -
607. PIR motion sensor interface with AVR-microcontroller ATMEGA32 Passive Infra red sensor also known as PIR sensors is
capable of detecting motion or movement within a certain range. These type of sensors have wide range of applications in
our daily life and it is essential to learn the interfacing method. This article is…... Listed under: AVR ATmega Tutorial, Sensor -
608. Analogue to Digital Conversion on an ATmega168 Many AVR microcontrollers are capable of doing Analogue to Digital
Conversion. The ATmega168 has 6 ports (8 ports on the SMD packages) that can be used for analogue input. This tutorial
shows you how. The circuit The Breadboard layout is based on the Atmega8 breadboard…... Listed under: Android Projects,
AVR ATmega Tutorial, Microcontroller Programmer Projects
609. How to make an Arduino Pro Mini bare bones with Real-time Clock Recapitulation One thing I didn’t find clearly over the
internet is how to make an Arduino Pro Mini bare bones, that is, from the scratch, and how to make one on the breadboard.
This is really useful if you want to make a custom pcb/smd…... Listed under: Clock Projects, LED Projects
610. How to drive 595 shift registers with AVR hardware SPI Driving a shift register using an AVR chip’s built-in hardware is really
quite easy. Most of their offerings have an SPI module, or Serial Peripheral Interface. A shift register is exactly that, a
peripheral device that communicates via a serial line. All we need to…... Listed under: AVR ATmega Tutorial, Clock Projects
611. Make your own AVR JTAG debugger Tired of putting LEDs every time you want to check some value in the microcontroller?
Well, its time to build yourself a debugger. A debugger is a device which helps you run through your code in the
microcontroller step by step and also gives you…... Listed under: LED Projects, Robotics - Automation Projects
612. Introduction to Arduino UNO (uses AVR ATmega328) Overview Arduino is an Open Source embedded development platform
which is easy-to-use. It comprises of Hardware boards and Software tools. Examples of some of the most popular Arduino
Hardware boards are , Arduino Uno This board is designed around the ATmega328 AVR microcontroller. It is…... Listed under:
Android Projects, Microcontroller Programmer Projects
613. An AVR microcontroller based Ethernet device Ethernet has traditionally been a quite complex interface. All Ethernet chips
until today had 100 pins or more, where difficult to find in small quantities and difficult to use from a small microcontroller
with little memory. Microchip has changed the world with their new ENC28J60…... Listed under: Other Projects
614. Fastest Finger First Quiz Project using ATmega16 Most of you must have watched quiz games in TV shows or at your schools
where few contestants are required to press a switch if they know the answer to the question. An electronic system is
required to find out exactly which one of then…... Listed under: LED Projects
615. Making a LED Message Display with Keyboard Interface LED signage has become the choice in modern days to convey
message to visitors of a venue. Be it corporate office, shops, restaurants or any kind of social functions like marriages. Some
big and complicated display needs dedicated control PCs and designers to build contents…... Listed under: LED Projects

616. LED Dot Matrix Room Temperature Display using P10 and ATmega8 Room temperature display on big screen is a common
requirement from industrial sector. Used in server rooms, PLC rooms, storage rooms and many other places in an industrial
units. Traditionally seven segment displays of big size (say four inch height) were used. But now a…... Listed under: LED
Projects
617. P10 LED Display Panel Interface with AVR ATmega8 Making LED displays and signage is a complete industry in itself serving
all sorts of clients like banks, railway stations, factories, airport and more. In earlier days display units were made using
individual LEDs carefully placed and soldered to make matrix of display. But this…... Listed under: LED Projects
618. Control Electrical Appliances from Android Smart Phone using Bluetooth : Project Construction Connecting Bluetooth
Module with Development Board The Bluetooth module has seven interface pins of which two are NC (not connected) pins.
The table below shows how you can interface with it our low cost AVR development board. Bluetooth Module Dev Board
GND GND RST PD2…... Listed under: Phone Projects
619. Home Appliance Control over Mobile Network You can call up on your colleague's mobile number and ask him/her to turn
on or off the lights or other appliance of your office. You may be any where in the world at that time, as mobile network
allows to to talk to anyone…... Listed under: Phone Projects
620. ATMega328 Board The ATMega328 board is a microcontroller board based on the ATmega328, The board contains
everything needed to support the microcontroller. The board need 5VDC to power it. Simply connect the power connector to
a computer with a USB cable or power it with a AC-to-DC adapter or…... Listed under: Battery Projects
621. ATTiny 2313 BOARD his board is a development board on which you can build your projects. It is suited for educational use,
experiments or prototyping. The board uses the ATTiny2313 microcontroller with a 20Mhz clock. The board contains the ISP
10-pin connector for in circuit serial programming. It…... Listed under: LCD Projects
622. LED Mood light In this projects 8 different colors are displayed with the use of a RGB LED. The microcontroller that is used is
the ATMega8. An RGB LED is a LED which has three LED's integrated in one packaging. These LED's have the colors red,
green, and…... Listed under: LED Projects
623. servo motor controller In ths project you can learn how to build a servo controleer motor with the ATMEGA328 board. The
position of the servo motor is controlled by the software (sweep back and forth) or by a potentiometer. The position of the
servo motor is set by…... Listed under: Motor Projects
624. LED Driver MAX7219 – clock Below is the schematic that shows how the IC is wired to the ATMEGA328 microcontroller and
the 4 digit 7-segment display with comon cathode. Besides the MAX7219 you need only three other external components:
two capacitors and one resistor. The capacitors are here to…... Listed under: LED Projects
625. Using Push Button Switch with Atmega32 and Atmel Studio This tutorial is meant for beginners in the field of Atmel AVR
programming. I hope that you already read my first tutorial Blinking LED using Atmega32 and Atmel Studio. In most of the
embedded electronic projects you may want to use a push button switch…... Listed under: LED Projects
626. Build Your Own Microcontroller Based PID Control Line Follower Robot (LFR) – Second Part One of the interesting parts in
building the Line Follower Robot is; you could start it with a very simple version by using just two transistors with the LED and
LDR for sensor (Build Your Own Transistor Based Mobile Line Follower Robot – First Part)…... Listed under: Robotics -
Automation Projects
627. Basic User’s Experiment Notes The “Basic User’s Experiment Note” is based on the popular 8-bit Atmel AVR ATmega328P microcontroller using
AVRJazz 28PIN development board. This e-book covering most of the Atmel AVR ATmega328P microcontroller important features. With almost 140
pages, this e-book is organized similar to many of the…... Listed under: Sensor - Transducer - Detector Projects

628. Basic Servo Motor Controlling with Microchip PIC Microcontroller The servo motor is widely used in model hobbyist such as
airplane R/C model for moving the rudder, ailerons, elevators and acceleration control or in the car R/C model for steering
and acceleration control. In this tutorial we will learn how to control the servo…... Listed under: Motor Projects
629. OH HAI! on Windows 10 IoT Core Story Oh, Hai Hai ('hi') is an integration point for several stand alone smart home
technologies. Hai runs on the Raspberry Pi and can be adapted to optimize electricity consumption (lighting/HVAC) and
water usage (irrigation/rain collection) in a number of ways. Hai was originally envisioned…... Listed under: Home Automation
Projects
630. ThiDom Home automation Story This project uses Arduino, Raspberry and Attiny, it allows you to control nd monitor your
home (AC outlet, shutters, heater, light, opening detector, temperature ...). The raspberry is the web server allowing control all
arduino These can be controlled from any web browser around…... Listed under: Home Automation Projects
631. Cellular Data Logger Story I have been collecting data from Raleigh's trails and parks for the last couple years. My primary
platform has been a custom Arduino board I developed for low-cost (hey, these things may get damaged or stolen) and long
battery life. I wanted a connected…... Listed under: Sensor - Transducer - Detector Projects
632. Physical computing with ATtiny Story I have a nice "carranca" (or wall mask) from Chile that stands in my corridor. It's a very
beautiful decorative mask that I liked from the very first moment I saw it at the shop. Few weeks ago I wondered if I could
bring…... Listed under: Sensor - Transducer - Detector Projects
633. POV Cylinder with Arduino Due Story Introduction This is my first Arduino project. My work was inspired by several maker
projects that created Persistence of Vision Displays [2,3,4]. Persistence of vision (POV) refers to the optical illusion whereby
multiple discrete images blend into a single image in the human mind and believed to…... Listed under: LED Projects
634. OLED on the Cheap! Things used in this project Hardware components: OLED 128x64 SPI-capable Available on Aliexpress or
eBay for $4 to $20 × 1 For standard Arduino platforms, use the unmodified Adafruit libs × 1 Story I like cheap electronics for
playing. Cheap is good for budget conscious…... Listed under: LED Projects
635. Tinker's Word Clock – REVISITED! NOW 110% more AWESOME I have been tinkering with Word Clocks for years. There is only
one thing I like more than making word clocks… it’s designing them so that they are easy to put together. This tutorial will go
through my latest version (5!!!!!). By the end of…... Listed under: Clock Projects, Home Automation Projects
636. nRF24L01+ with ATtiny85 3 Pins Story This would be the continuation of my previous project Programming ATtiny85 with
Arduino Uno. Now with cheaper ATtiny85 in place I was looking for cheaper ways to transmit the sensor data. Which brought
me to nRF24L01+ a cheap, low power RF transceiver. This seemed…... Listed under: Other Projects
637. Programming ATtiny85 with Arduino Uno Story I am working on a project which requires reading multiple sensor data on
different locations. These require only few PWM pins so using multiple Arduino Uno would be expensive and unnecessary. So
I decided to use ATtiny85 microcontroller in place of Arduino Uno development…... Listed under: PWM Projects
638. Franzino is a low cost Arduino standalone board Hardware components: Atmel ATmega328P × 1 16 MHz Crystal × 1 Capacitor 22 pF × 2 Capacitor
100 nF × 5 LED (generic) × 2 Linear Regulator (7805) × 1 Capacitor 10 µF × 2 1N4007 – High Voltage, High Current Rated Diode × 1…... Listed under:

639. Arduino Without External Clock Crystal on ATmega328 Story An Arduino consists of many components like: a linear regulator,
USB to Serial microcontroller, debug LED, power LED, reset button, RX & TX LED, crystal oscillator, etc. But a minimal circuit
can have just the brain of the Arduino UNO, that is, an ATmega328p…... Listed under: Clock Projects
640. Reducing Arduino Power Consumption Story When it comes to portable electronics, one of the most important features is
how to maximize the battery life. The ATmega328P, used on popular boards like the SparkFun RedBoard, Arduino Uno, and
Pro Mini are actually quite power hungry. The RedBoard and Arduino Uno,…... Listed under: Other Projects
641. Gimmick on Barebones Arduino 16MHz Story Did you see this 8MHz no-crystal Arduino? Arduino on Internal Oscillator
Crystal as Clock Source by Naman Chauhan is a great project if you can live with 8MHz using the internal RC oscillator of the
Atmega328P chip. I really like Naman's project; I did…... Listed under: Other Projects
642. Tri-Mode Digital Clock with ATtiny85 and RTC Story Hello everybody, This is my first project using ATtiny85 microcontroller
and also including a Real Time Clock (RTC) working with it. The use of ATtiny85 is a very interesting way to shrink your
Arduino projects in a final tiny version. The Three-Modes Digital Clock…... Listed under: Clock Projects
643. Bootload Your ATtiny85 Story What is a Bootloader? Microcontrollers require a programmer to install firmware on them. A
programmer is a device, that when combined with software, loads firmware to the microcontroller. There are many
programmers available. I won't go into to detail about them, but I will…... Listed under: LED Projects
644. SSD1306xLED Tinusaur ATtiny85 Library for SSD1306 Story SSD1306xLED is a C library for working with the SSD1306 display
driver to control dot matrix OLED/PLED 128×64 displays. It is intended to be used with the Tinusaur board but should also
work with any other board based on ATtiny85 or similar microcontroller. The…... Listed under: LED Projects
645. 3D-Printed RGB Wallet Stand out from the crowd with this unabashedly ostentatious excuse for a wallet. It's got plenty of
space, RGB lights, and you can even put your name on it for added vanity. Interested? Keep reading!In the files section of this
build you can find two…... Listed under: Other Projects
646. Open Source IoT Platform The Project Intended as open source for those who want to build their own dosimeter with their
own tools, this is an IOT device that can take several sensors and have the data centralized online. The readings are accessible
via a RESTful API, or by…... Listed under: Home Automation Projects
647. Light-Up Poker Chip Spice up your poker games with these cool blinking chips. They can be programmed on the fly to have a
certain number of the LEDs illuminated to indicate value, or you can have the lights blink in a cool pattern. They make great
playing chips…... Listed under: Game - Entertainment Projects
648. Scrumtato: Make Daily Stand-Ups Agile Again Story The following was originally published in my blog. At Delphi in
Gothenburg, where I am currently employed, we create all kinds of cool products for the automotive industry. To organize
our development process, we use SCRUM and abide by the Agile principles. Every morning,…... Listed under: Other Projects
649. Goldilocks Analogue – Prototyping 3 Following my initial design article, and the follow up design article, I’ve put quite a lot of thought into how I can
make this Goldilocks Analogue device best achieve my stated goals. Pictured is the new 3rd Goldilocks Analogue Prototype. I'm now working on the
4th Goldilocks Analogue…... Listed under: LCD Projects

650. Playing Simon On A Hacked Farm Toy About My kids have a plastic farm toy. It neighs, it baas, and frankly, it grates. But since
I tricked it out with a microcontroller brain, at least it can play Simon. One of the marvels of parenthood is the sheer volume
of noisy plastic junk…... Listed under: Phone Projects
651. Coil Winding machine counter with Atmega8 and Reed relay Connectors Everything has been mounted on a test board,
including the headers for: ISP programmer (USBAsp), the 5110 Nokia LCD, the power supply (5V in, fed to the 3.3V regulator),
the Reed relay connector, the reset button connector and another 2 pins connector, used to…... Listed under: Motor Projects
652. Bluetooth remote controllable (Lego) cars How it started It started with the idea to make a technical proof of concept
combining the Physical Web and WebBluetooth. The Physical Web is an effort by Google to allow interacting with "things"
without fiddling around with installing apps or setting anything up. The…... Listed under: Car Projects
653. Markov Music Box markov summary Traditional music boxes play one or two tunes very well, but are not very interactive. Put
differently, they have a high quality of synthesis, but a fixed-pattern note sequencer and fixed tonal quality. I wanted to build
a device which would play an…... Listed under: PWM Projects, Sound - Audio Projects
654. DIY Canon IR Remote Hardware components: Atmel ATtiny13a CHF 1.25 × 1 Osram SFH409 IR Diode CHF 0.75 × 1 Battery
holder CR1220 CHF 0.65 × 1 Coin Cell Battery CR1220 3V × 1 Push Button CHF 0.25 × 1 Resistor 15Ω CHF 0.07 × 1 Micro
Slide Switch…... Listed under: How To - DIY - Projects
655. wozItDo: Tiny IQ puzzel, BIG challenge Hardware components: Atmel ATTiny85 × 1 LED (generic) × 3 Resistor 221 ohm Or
similar, I used 220 ohm × 3 SparkFun Pushbutton switch 12mm or similar × 1 Coin Cell Battery Holder × 1 Coin Cell Battery
CR2032 any 3v cell that fits is…... Listed under: LED Projects
656. The Tinusaur Project About The Tinusaur What is it Briefly, the Tinusaur is a minimal micro-controller hardware configuration
based on Atmel AVR ATtiny family of products and more specifically those with DIP-8 case such as
ATtiny25/ATtiny45/ATtiny85, ATtiny13 as well as their variations. The goal of the Tinusaur project…... Listed under: Other
Projects
657. Yet Another Z180 (YAZ180) Project I’m thinking about a new project, something a little unusual but still with a rich history of
information upon which to base the build. On Tindie, I found the RC2014 project which is a build of a Z80 platform but based
on some modern components.…... Listed under: LED Projects
658. Goldilocks Analogue Synthesizer For the past year, I’ve been prototyping an Arduino clone, the Goldilocks Analogue, which
incorporates advanced analogue output capabilities into the design of the original Goldilocks with ATmega1284p AVR MCU
and uSD card cage. Recently the design scope crept up to include two SPI memory…... Listed under: Other Projects
659. Arduboy Solar Charge Controller, Inverter, PowerBank, Lamp About this Project I have a few solar panels, 12 Volt batteries,
transformers and few more stuff laying around for a while crying out aloud to make some good use of them. Thus the birth
of this device - complete small PV solution on a…... Listed under: Solar energy projects
660. Sigfox Talking Plant Hardware components: Arduino UNO & Genuino UNO × 1 Atmel ATA8520D (EVK arduino) × 1 Software apps and online services:
Sigfox Twitter Story What is Sigfox Talking Plant? It is a simple project based on Sigfox network to make a plant talk on Twitter. The…... Listed under:

Other Projects
661. Make your own remote temperature/humidity sensor Hardware components: Atmel atmega 328p-pu × 1
ControlEverything.com SI7020-A20 I²C Humidity and Temperature Sensor ±4%RH ±.4°C × 1 433 MHz transmitter / Receiver
kit × 1 AMS1117-ADJ voltage regulator × 1 Capacitor 100 µF × 1 Capacitor 100 nF × 1 Resistor 1k ohm ×…... Listed under:
Sensor - Transducer - Detector Projects
662. XBee Walkie Talkie Hardware components: Goldilocks Analogue Still as prototype currently, but functionality can be recreated
with MCP4822 DAC, Microphone Amplifier, and Headphone Amplifier, together with Arduino Uno. × 1 MAX9744 × 1
MAX9814 × 1 MCP4921 DAC × 1 Arduino UNO & Genuino UNO × 1 Arduino…... Listed under: Other Projects
663. Bionic Organs/Devices/Limbs Wireless Charging Hardware components: IDT Qi 5W Transmitter Prototype Kit × 1 IDT Qi 5W
Receiver Prototype Kit × 1 Atmel Atmega328p × 1 HC-SR04 Ultrasonic Sensor × 1 Hand tools and fabrication machines:
Arduino cc Schemeit PCBWeb Story Bionic devices/organs has a limited lifetime where its…... Listed under: Other Projects
664. Personal Home Assistant Hardware components: Arduino UNO & Genuino UNO × 1 Atmel ATMega328 × 1 Linear Regulator
(7805) × 1 Jumper wires (generic) × 20 Resistor 10k ohm × 5 Resistor 1k ohm × 5 Capacitor 22 pF × 6 16 MHz Crystal × 3
SparkFun Pushbutton…... Listed under: Home Automation Projects
665. Darby's not dead. Hardware components: Particle Spark Core × 1 atmega168 × 1 pn532 breakout board/ adafruit × 1 Story
In the future there is a bar where all the dead punk rockers hang out. They are each given a MiFare classic card programmed
with their name and…... Listed under: Other Projects
666. Digital Thermometer using AVR, LM35 and 16×2 LCD Thermometers are the device we use to measure the temperature in
any desired scale and we all will be quite familiar with the analog thermometers. There are some disadvantages in analog
thermometers and this can be overcome by using this digital thermometer using avr. The…... Listed under: LCD Projects
667. AVR Serial Communication (UART) Programming tutorial This tutorial focuses to teach you how to program AVR Serial
Communication (UART). UART plays an important role in almost every embedded applications which we see in our day to life
and hence it was considered to be very important concept in every Microcontroller. The…... Listed under: Other Projects
668. Tutorial on printing image in Graphical LCD (GLCD) using Atmega32 Graphical LCD’s known as GLCD are display devices
which are capable of displaying graphical images, customized characters, etc. This paves way for any system to present
information to the end user by means of interactive graphics such as printing image. Bored of using the old…... Listed under:
LCD Projects
669. Creating Pac man custom patterns and animation in LCD display LCD modules are widely used to display calculated data’s, user references and much
more. In addition all character based LCD which uses HD44780 controller consists of a special RAM known as CGRAM which allows user to create
custom patterns. This tutorial will teach you to…... Listed under: LCD Projects

670. LCD Interface with Atmega32 AVR microcontoller for beginners LCD’s are quite familiar module when comes interfacing with
microcontrollers. We can find these display modules in plenty of instances where a specific info is need to be displayed for
the viewers. This article explains LCD interface with Atmega32 a AVR family Microcontroller and display…... Listed under: LCD
Projects
671. Digital Clock using AVR Atmega16 Microcontroller Digital clocks revolutionize the way we live our daily life as it helps people
to stick with their schedule. This article will teach you to build your own Digital clock using DS1307 RTC Chip with Atmega16
microcontroller. As we all know that DS1307 is a…... Listed under: Other Projects
672. Volt-Amp meter using AVR microcontroller Voltage and current are two most important parameters of electricity. This project
teaches you to build a simple volt-amp meter using avr microcontroller. This project may not enable you to build a high end
measurement tool but will be a good diy project which gives a…... Listed under: Metering - Instrument Projects
673. Door/Window alarm circuit Door or Window alarm circuit have been used widely in many homes to detect intrusion. A simple
search in internet might fetch you lot of alarms for you to buy. But making your own alarm will be something special and
that’s the purpose of this…... Listed under: Other Projects
674. Automatic plant watering system using AVR(Atmega16) Microcontroller Plant watering system evolved through various
stages where primitive irrigation systems possess many drawbacks as it fails to conserve water and human energy. So
introducing Automation in it can help us to overcome these drawbacks and pave way to conserve water. This can be done…...
675. ATmega32 Switch Toggle Program ATMega32 switch code is extremely simple to implement, and this article looks into how to
write the code to make an LED light up when a switch is pressed. The atmega32-switch-code.c program tests the switch input
to the ATMega32 Development System. There are many ways…... Listed under: LED Projects
676. ATmega32 blinking LED Lights Using the ATMega32 microcontroller to flash or blink some LEDs is extremely simple and this
tutorial shows how to make a blinker circuit including the example program code to blink eight LEDs. In this tutorial, you will
learn how to make a program to blink…... Listed under: LED Projects
677. GSM Based Home Automation GSM based home automation, project allows you to control electrical appliances using your
mobile phone SMS. It consists of ATmega8 microcontroller, SIM300 GSM modem, Relays. There are many Home Automation
Systems available in our market. Most of these are simple home appliances controlling systems like DTMF controlled…...
Listed under: Home Automation Projects
678. GSM Based Fire Alarm System GSM, Microcontroller Based Fire detection and SMS Alert system, it uses LM35 Temperature
Sensor and MQ2 for Smoke sensing and 16x2 LCD is used to display temperature and Smoke Level, Over limit set points are
set inside the program you can modify it as per…... Listed under: Security - Safety Projects
679. Password based door locking system Password based door locking system, uses Matrix keypad to enter the password, This
project is extended to operate on IR Remote RC-604, In this project all required data is given Circuit diagram, C code, PCB
design and All related data, This project is based on…... Listed under: Security - Safety Projects
680. AVR Microcontroller based Temperature Monitoring and Control System AVR Microcontroller based Temperature Controller,
it uses LM35 Temperature Sensor for measurement of temperature and 16x2 LCD is used to display temperature set point,
Heater Status and current temperature, It controls temperature by turning on and off of the heater using relay. This project
is…... Listed under: Sensor - Transducer - Detector Projects, Temperature Measurement Projects
681. Bluetooth based home automation Bluetooth based home automation, project allows you to control electrical appliances
using your android mobile phone. It consists of ATmega8 microcontroller, HC-06 Bluetooth module, Relays. There are many
Home Automation Systems available in our market. Most of these are simple home appliances controlling systems
like DTMF controlled…... Listed under: Home Automation Projects

682. Fingerprint based security system This AVR microcontroller based project demonstrates Finger print based access control /
security system, in this project we have provided all required data, PCB, Code, Circuit Diagram, Proteus Simulation. This
project operates a relay based on valid finger detection. It is provided with 6-Keys for…... Listed under: Security - Safety
Projects
683. Token number display system using microcontroller Bank token number display project is build using ATmega8
Microcontroller and ULN2003 for driving large LED display, PCB layout, Circuit diagram are self explanatory. It is capable to
display three digits, its simple project using microcontroller. Token issue systems are ideal for banks, airports, public…... Listed
under: LED Projects
684. 16×2 LCD interface with microcontroller Interfacing with Hitatchi 44780 The purpose of this page is to give a brief tutorial on
how to interface with Hitatchi 44780 based LCDs. I have tried to provide the all the data necessary for successfully adding
LCDs to your application. The most common connector…... Listed under: LCD Projects
685. DS1307 RTC Interfacing with AVR microcontroller In this tutorial we will learn How to interface RTC DS1307 with AVR
microcontroller. We are using Atmega8 for the demo. GENERAL DESCRIPTION The DS1307 serial real-time clock (RTC) is
a low-power, full binary-coded decimal (BCD) clock/calendar plus 56 bytes of NV SRAM. Address and data are…... Listed
under: Clock Projects
686. Analog to Digital Converter AVR C Programming One of the important features in today’s modern microcontroller is the
capability of converting the analog signal to the digital signal. This feature allows us to process the analog world easily such
as temperature, humidity, light intensity, distance, etc; which usually captured by electronics sensor…... Listed under:
687. AVRJazz Mega168/328 Learning and Development Board The AVRJazz Mega168 board from ermicro is designed to be used
both as the AVR microcontroller learning and development board. The AVR Jazz Mega168 board is stand alone
microcontroller module equipped with the latest Atmel high performance low power technology AVR ATMega168 or
ATMega328 microcontroller…... Listed under: Development Board - Kits Projects
688. Introduction to AVR Microcontroller Pulse Width Modulation (PWM) PWM is used in many industrial mostly for controlling
the motor speed. The PWM is used because it’s the most efficient method comparing to the analog one. That’s why most of
the modern microcontrollers today have this features build in. How does this PWM works…... Listed under: PWM Projects
689. Atmel AVR ISP Microcontroller Programmer Project One of the frustrating part in learning AVR microcontroller for the
beginners is the AVR microcontroller programmer. The question is how to program my AVR mircrocontroller; actually if you
googling on the internet and search for AVR ISP Programmer there are plenty information; start from…... Listed under:
690. AVR Twinkle Twinkle Using PWM Project Would be interesting if we could make our microcontroller to sing for us not just
beeping or blinking; this project is all about using the powerful AVR ATmega168 16-bit PWM feature to produce accurate
musical notes such as playing the child’s favorite Twinkle-Twinkle Little Star…... Listed under: PWM Projects
691. AVR LCD Thermometer Using ADC and PWM Project Sometimes we need our microcontroller to interact with more human
readable information. It will be better for us if we could make it display the words not just blinking the LED. Today most
modern gadget such as mobile phone and PDA, use LCD (Liquid Crystal…... Listed under: PWM Projects
692. Controlling DC motor with AVR ATtiny13 PWM and ADC Project It’s interesting to explore what we can do with this tiny 8
pins; 8-bit microcontroller. The ATtiny13 is the smallest and cheapest Atmel AVR 8-bit microcontroller families but yet, it’s
loaded with sophisticated peripherals such as two 8-bit PWM channels and 4 channels 10-bit ADC.…... Listed under: PWM
Projects
693. Transforming your AVR Microcontroller to the I2C or TWI Slave I/O Expander Project The I2C bus (read as I squared C) is one
of the most important embedded system serial bus interface first introduced by Philips in 1980; using just two lines called
SCL (serial clock) and SDA (serial data) respectively make the I2C bus is a perfect…... Listed under: Other Projects
694. Developing Embedded Application with BASIC Language on the Microchip PIC18F Microcontroller using the Amicus18 Development system The
BASIC (Beginners’ All-purpose Symbolic Instruction Code) language has been known as one of the popular high level
language choice in embedded system today. In fact the born and development of the personal computer (PC) we use today
has been influenced by the used of…... Listed under: Development Board - Kits Projects

695. Build your own stopwatch using Maxim MAX7219 Serially Interfaced, 8-Digit LED Display Drivers One of the basic usage of
the TIMER peripheral on every microcontroller is to provide the accurate timing mechanism. Using the TIMER peripheral as
the basic timing, we could easily develop a stopwatch and display it to the 8-Digit seven segment numeric LED display.
Thanks…... Listed under: Clock Projects
696. Building the I2C Smart DC Motor Controller with Atmel AVR Microcontroller – Part 1 The idea of building my own I2C (read as
I square C) smart DC motor controller is came to me when I was learning and playing together with my son on his LEGO®
MINDSTORM® NXT 2.0 about a year ago. The NXT sophisticated controller also…... Listed under: Motor Projects
697. Telepresence Robot using Microchip PIC16F1829 and Atmel AVR ATmega168 I2C Smart DC Motor Controller Microcontroller – Part 2 The I2C (read as I
square C) smart DC motor controller is designed using the Atmel 8-bit AVR Atmega168 microcontroller and configured to act
as the I2C slave device where it could be controlled by other microcontroller or microprocessor through the I2C SDA (serial
data)…... Listed under: Robotics - Automation Projects
698. The LED Chasing Effect Project using Atmel AVR Microcontroller One of the interesting projects for most of the embedded
beginners enthusiasts or hobbyists is to build the LED chasing effect. In this project we are going to use both the Arduino IDE
and Atmel AVR Studio to program the AVR ATMega168 microcontroller, therefore you…... Listed under: LED Projects
699. How to use I2C-bus on the Atmel AVR Microcontroller I2C (read as I Squared C) bus first introduced by Philips in 1980,
because of its simplicity and flexibility the I2C bus has become one of the most important microcontroller bus system used
for interfacing various IC-devices with the microcontroller. The I2C bus use only…... Listed under: Other Projects
700. Interfacing GSM Module with Atmega32 AVR microcontroller GSM (Global System for Mobile Communication) technology
lets user to communicate with others across mobile networks hence it offers a vast area of coverage. Interfacing GSM
technology with microcontroller will enable us to extend the communication to cover large area. This tutorial will teach
you…... Listed under: Other Projects
701. Integrating Wiznet W5100, WIZ811MJ network module with Atmel AVR Microcontroller The rapid penetration of the internet
networks into many of today’s modern homes and personal gadgets (e.g. smart phone and smart pads) opening a
tremendous useful and interesting embedded system application that could be integrated into our house or known as the
intelligent house. For…... Listed under: Internet - Ethernet - LAN Projects
702. Using Serial Peripheral Interface (SPI) Master and Slave with Atmel AVR Microcontroller Sometimes we need to extend or add
more I/O ports to our microcontroller based project. Because usually we only have a limited I/O port left than the logical
choice is to use the serial data transfer method; which usually only requires from one up to…... Listed under: Other Projects
703. Working with the Comparator Circuit Sometimes in the embedded system world we need to process the analog world and
sending the signal to the microcontroller when the analog signal exceed some predetermine limit we’ve set. Some example
of this situation is to send the interrupt signal to the microcontroller operation…... Listed under: Development Board - Kits
Projects
704. Using Transistor as a Switch Most of microcontrollers work within 5 volt environment and the I/O port can only handle
current up to 20mA; therefore if we want to attach the microcontroller’s I/O port to different voltage level circuit or to drive
devices with more than 20mA; we need to…... Listed under: Other Projects
705. Working with AVR microcontroller Communication Port Project Back in the old days the COM port or known as RS-232 (EIA-
232 standard) is one of the essential communications protocol and hardware use in many computer system installation start
from small UNIX machine to the mainframe. The RS-232 protocol is used by terminal such…... Listed under: Other Projects
706. Microwave Controller using ATmega8 – AVR Project The user interface has the following parts. Output Device: A 16×2 alphanumeric LCD Module is
used as the main output device. It can display numbers, alphabets and few symbols. It can show two line and each line can have 16 characters. The
backlight enables the…... Listed under: LCD Projects

707. Stepper motor control with an ATmega8 microcontroller This note provides basic implementation details and procedural
information to design and assemble a stepper motor system. The controller discussed here is the ATmel mega8, an 8-bit
microcontroller (MCU). The note consists of a general description and gives highlights of implementing a basic stepper
motor…... Listed under: Motor Projects
708. Interfacing Servo Motor with Atmega32 Microcontroller Servo Motor is a DC Motor equipped with error sensing negative
feedback to control the exact angular position of the shaft. Unlike DC Motors it will not rotate continuously. It is used to
make angular rotations such as 0-90°, 0-180° etc. Stepper Motors can also…... Listed under: Motor Projects
709. Interfacing DC Motor with Atmega32 Microcontroller In some of your electronic projects you may want to control a DC
Motor with Atmega32 Microcontroller. We can’t connect a DC Motor directly to a microcontroller due to following reasons. A
microcontroller can’t supply the current required for the working of DC Motor. ATmega32 Microcontroller can source or…...
Listed under: Motor Projects
710. Interfacing LCD with Atmega32 Microcontroller using Atmel Studio As we all know LCD (Liquid Crystal Display) is an
electronic display which is commonly used nowadays in applications such as calculators, laptops, tablets, mobile phones etc.
16×2 character LCD module is a very basic module which is commonly used by electronic hobbyists and is used in…... Listed
under: LCD Projects
711. Blinking LED using Atmega32 Microcontroller and Atmel Studio Similar to printing ‘Hello World’ in C or C++, the very first
step towards programming a microcontroller is Blinking a LED with a delay. Atmega32 is a very popular high performance 8
bit AVR Microcontroller. For this example project we need to use two registers…... Listed under: LED Projects
712. Interfacing rotary encoder to Atmega32 Recently I was working on a project that involved rotary encoder. I thought I'd share
some thoughts on how rotary encoder can be interfaced and programmed. Actually it is easy to work with rotary encoders -
interfacing is simple – only three wires are required…... Listed under: LCD Projects
713. Graphical LCD Text Display The Graphical LCD Text Display is complete! I've used the same Atmel ATMega8 controller that I
used in the Composite Video Display. The interface is the same as well; an 8 bit parallel port with a strobe input and a busy
output. …... Listed under: LCD Projects
714. An advanced energy saver project with DTMF capabilities to use electricity efficiently by reducing the unwanted uses.
INTRODUCTION: A lot of electricity is wasted due to ignorance or fault of the user. Sometimes a person in the room turns
on all the electric equipments which is of no use to them. As an example, supposedly a person enters in the hall or
conference…... Listed under: Other Projects
715. Analog to Digital Converter of ATmega32 with LED Display Microcontrollers are capable of detecting binary signals: is the
button pressed or not? These are digital signals. When a microcontroller is powered from five volt, it understands zero volts
(0V) as a binary 0 and five volts (5V) as a binary 1. But the real…... Listed under: LED Projects
716. 4X4 Keypad Interfacing with ATmega32 and LED Display Keypads are parts of HMI or Human Machine Interface and play
really important role in a small embedded system where human interaction or human input is needed. Matrix keypads are
well known for their simple architecture and ease of interfacing. In this project, we will…... Listed under: LED Projects
717. 4X4 Keypad based Password with ATmega16 and LED Display Security is a prime concern in our day-today life. Everyone wants to be as much secured
as possible. Keypad based password is one of the many method and the most common and easy one to provide security to any system. In this project,
we will…... Listed under: LED Projects

718. 4X4 Keypad based Password with ATmega32 and LCD Display Security is a prime concern in our day-today life. Everyone
wants to be as much secured as possible. Keypad based password is one of the many method and the most common and
easy one to provide security to any system. In this project, we will…... Listed under: LCD Projects
719. 3-axis Accelerometer Sensor-ADXL335 Interfacing with ATmega32 ADXL335 accelerometer sensor is a MEMS
(Microelectromechanical systems) sensor which can measure static acceleration of gravity in tilt-sensing applications, as well
as dynamic acceleration resulting from motion, shock, or vibration. The accelerometer sensor is used in mobile devices,
gaming systems, disk drive protection, image stabilization,…... Listed under: Sensor - Transducer - Detector Projects
720. Accelerometer based Hand Gesture Controlled Wheel Chair with ATmega32 for Physically Handicapped In this project, we will
learn How to design an Accelerometer based Hand Gesture Controlled Wheel Chair with AVR ATmega32 Microcontroller for
Physically Handicapped. Here, we will use our hand gestures as input signals to drive the wheel chair in different direction
and we will…... Listed under: LCD Projects
721. DS1307 RTC based Digital Clock Designing in 12 Hour Format with ATmega32 and 7-Segment Display A digital clock is a type
of clock that displays the time digitally (i.e. in numerals or other symbols), as opposed to an analog clock, where the time is
indicated by the positions of rotating hands. The clock/calendar provides seconds, minutes, hours information. The clock…...
722. AVR uartConfig – an atmega and arduino eeprom config library Update to version 2014-06-13 AVR uartConfig is a small
footprint library you can use to config your micro eeprom through uart communication. AVR uartConfig is a set of tools
running on Windows, Linux and Mac, made up or: a avrgcc firmware library a commandline utility…... Listed under: AVR
ATmega Projects
723. Accelerometer and Relay based Hand Gesture Controlled Wireless Home Automation System with ATmega32 using 433MHz RF In this project, we will
learn How to design an Accelerometer and Relay based Hand Gesture Controlled Wireless Home Automation System with
AVR ATmega32 microcontroller using 433MHz RF. Here, we will use different hand gestures as input signal to control the
appliances i.e 2 bulbs…... Listed under: LCD Projects
724. Password Protected BT136 Triac based Keypad Controlled Wireless Home Automation System with ATmega32 using 433MHz RF-I In this project, we
will learn How to design a Password Protected BT136 Triac based Keypad Controlled Wireless Home Appliances System with
AVR ATmega32 microcontroller using 433MHz RF Part-I. Here, we will use the 4X4 keypad as the input device to enter the
password and…... Listed under: Home Automation Projects
725. LM35 Temperature Sensor Interfacing with ATmega32 and LED Display LM35 series is a low cost and precision Integrated
Circuit Temperature Sensor whose output voltage is proportional to Centigrade temperature scale. Thus LM35 has an
advantage over other temperature sensors calibrated in Kelvin as the users don’t require subtraction of large constant
voltage to obtain…... Listed under: LED Projects
726. Atmega 32u4 Based Wireless USB Keyboard How a generic keyboard is made has been already explained in the Atmega 32u4
Based Generic USB Keyboard Project. In this project a wireless keyboard will be designed. For making a wireless keyboard,
there will be two circuits involved in the project - a transmitter…... Listed under: Other Projects
727. Atmega 32u4 Based LED Status In the Atmega 32u4 Based USB Controlled LED Series Project, it was demonstrated how to
use control transfer to receive data from computer to the peripheral. In this project, it will be demonstrated to transfer data
from microcontroller to the host computer. For this, the…... Listed under: LED Projects
728. Atmega 32u4 Based Wireless USB Mouse How a generic mouse is made was explained in the Atmega 32u4 Based Generic
USB Mouse Project. In this project a wireless mouse will be designed. For making a wireless mouse, there will be two circuits
involved in the project - a transmitter circuit which…... Listed under: Other Projects
729. Atmega 32u4 Based USB Speaker A speaker is a device that produces sounds from the electrical signal having audio
encoded. The speakers usually have a 3.5 mm jack for audio output from the computer. Nowadays USB interface is also
gaining popularity for interfacing audio devices with the computer. A lot…... Listed under: Other Projects

730. Atmega 32u4 Based USB Musical Keyboard The music keyboard is one of the most common musical instruments. The
electronic musical keyboards have been around for a long time. The electronic music keyboards synthesize musical sounds
electronically according to MIDI (Musical Instrument Digital Interface) standards. Fortunately, the USB protocol does have
provision…... Listed under: Other Projects
731. Atmega 32u4 Based USB EEPROM Reader External memories are frequently used to store and carry computer data. The USB
flash drives are quite common nowadays. This project is an attempt to demonstrate making of USB storage devices. The
project converts an external EEPROM which basically has I2C interface to an USB…... Listed under: Other Projects
732. Atmega 32u4 Based USB Controlled LED Series Throughout this USB series, different types of USB devices have been
designed and developed. These devices were enumerating with the host computer and then were using Class Specific
transfers for further USB communication. Like the Keyboard, Mouse and joystick devices were using interrupt transfers for…...
733. Atmega 32u4 Based USB Controlled Servo Motor In this project, a device will be designed which will allow controlling a servo
motor from the desktop computer on USB interface. For controlling a servo motor, PWM output needs to be generated from
the microcontroller. The length of the ON time of the PWM…... Listed under: Other Projects
734. Atmega 32u4 Based USB Digital Voltmeter In this project, a digital voltmeter will be designed which will show the voltage
reading on a desktop application. The device will read analog voltage with respect to the ground, digitize the reading and
send the reading to personal computer on USB interface. The device…... Listed under: Other Projects
735. Attiny85 As a Step/Dir Stepper Motor Controller Somewhere in Greece, someone did something never done before... Seen
those things before? Thing: 1 Thing: 2 Thing: 3 Oh, you have! You bought one of them you say? Oh... Don't worry, I did too.
They did the job, yeah. But we paid for them…... Listed under: Motor Projects
736. Custom PCB for Lights, Temperature, Video OSD and VTX PSU upgrades to HKing Rattler RC Car I’ve had the HobbyKing
Rattler for some time now and I’ve been making small modifications here and there which have accumulated over time and
has gotten to the point where it would be nice to have everything on a custom PCB. Here’s how everything looks…... Listed
under: Temperature Measurement Projects
737. Open Programmer – USB programmer for PIC, EPROM, ATMEL, SPI Open Programmer – An open source USB programmer for
PIC micros, I2C-SPI-MicroWire-OneWire-UNIO EEPROMs, some ATMEL micros, generic I2C/SPI devices and (soon) other
devices. Completely free and Open Source (including firmware) Programs PIC10-12-16-18-24, dsPIC30-33, EEPROMs type
24xxxx (I2C), 25xxx (SPI), 93xx6 (MicroWire), DS24xx (OneWire), 11xxx (UNIO),…... Listed under: Interfacing(USB - RS232 - I2c -
ISP) Projects
738. Updating electricity meter to communicate via WLAN A while ago Farnell sent email to me and offered one (inexpensive)
product as a sample in exchange for mentioning it at this blog. I browsed for a while for an interesting part and settled with
Microchip MRF24WB0MA/RM WiFi module (Order code 1823142). This module…... Listed under: Home Automation Projects
739. Using Maxim DS1307 Real Time Clock with Atmel AVR Microcontroller Using Atmega32 Building our own digital clock is one
of the dreamed project by most of the hobbyist or anyone that want to learn or involve seriously in the embedded system
world; the ability to integrate time, day and date to the embedded system is one of…... Listed under: Clock Projects
740. Single Chip Computer: Easy to Produce AVR BASIC Co This instructable will document and explain my latest project, a
standalone computer system based upon a single chip (IC); the ATmega 1284P. The 1284P is responsible for all aspects of the
system, including running the BASIC interpreter, generation RCA video signals and reading keyboard input.…... Listed under:
Android Projects
741. Doppler Radar for Collision Avoidance Introduction My project uses Doppler radar sensors in order to provide the user with
movement, speed, and distance information of their environment. An array of Doppler radar sensors are placed on the
user�s head and vibration motors are placed on the user�s chest, neck, back,…... Listed under: Sensor - Transducer -
Detector Projects
742. Drums Anywhere: solution to making a great drum beat Using 3D-printed boxes Introduction "The sound and experience of drums... Any time,
anywhere, with any object." -Project Soundbyte It's Friday night and you're hanging with your friends at home. There are no parties tonight and you
have seen everything on Netflix already - you're bored out of your…... Listed under: Sound - Audio Projects

743. Ultrasonic range-finder with haptic feedback Introduction "An ultrasonic range-finding hat with variable haptic feedback for
obstacle detection." -Project Sound Bite For our ECE 4760 final project, we designed and implemented an ultrasonic range-
finding hat that uses haptic feedback to alert its wearer about obstacles in his or her path. The…... Listed under: Sensor -
744. Capacitive Touch with Atmel’s AT42QT1070 Touch Sensor IC Rather than using an out-of-the-box capacitive touch solution
for my projects, I thought I’d attempt making my own little breakout board. The idea is to use a sensor capable of triggering
normal digital input pins using touch. This post covers the selected touch sensor IC,…... Listed under: Sensor - Transducer -
Detector Projects
745. AVR ATtiny USB Tutorial Part 2 This is the second part of my USB tutorial for ATtiny2313 and V-USB library. In the first part we
learned how to get 3.3V from USB to power our circuits. In this part, we will expand our setup with following parts: Larger
breadboard and additional…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
746. AVR Atmega audio input RMA using FFT Radix-4 audiogetradix4 is a simple library you can use to interface with a ac audio
input. It reads data from an ADC pin and returns the RMS value of the input using DFT Radix-4 algorithm. The discrete
Fourier transform (DFT) converts a finite list of equally-spaced…... Listed under: Sound - Audio Projects
747. Irradiance/Illuminance Meter using TLR235R sensor with AVR Atmega The TSL235 is a light-to-frequency converter. This
library reads TSL235 output frequency and convert it to irradiance, and then to illuminance. Irradiance is the power of
electromagnetic radiation per unit area (radiative flux) incident on a surface. It's expressed in watt per square metre, the…...
Listed under: Metering - Instrument Projects
748. An AVR Atmega LCD Menu builder library lcdmenu1 is a simple and small lcd menu builder for AVR Atmega. It works with
only 4 buttons (up, down, right, left), additional buttons can be added. It can also store values to eeprom User can use button
up and down to list menu categories, right…... Listed under: LCD Projects
749. An optical dust meter that uses the GP2Y1010AU0F sensor library made with AVR Atmega This project is a dust detector that
use the GP2Y1010AU0F sensor. Attached you can also find the GP2Y1010AU0F sensor library for AVR Atmega.GP2Y1010AU0F
is a dust sensor by optical sensing system. An infrared emitting diode (IRED) and an phototransistor are diagonally arranged
into this device.…... Listed under: Sensor - Transducer - Detector Projects
750. AVR Atmega dehumidifier controller board, update This project is an update to the previous dehumidifier based you can
here: http://davidegironi.blogspot.it/2013/04/avr-atmega-dehumidifier-controller.html This update adds some usefull
functions. The main issue that i've fixed is the microcontroller crash, that happens sometimes. I've noticed that sometimes the
controller stop running, crash or doesn't works as…... Listed under: Sensor - Transducer - Detector Projects
751. A simple brushless sensorless motor driver for AVR Atmega Brushless electric motor (BLDC motors) are synchronous motors
that are powered by a DC electric source via an integrated inverter/switching power supply, which produces an AC electric
signal to drive the motor. For an introduction to BLDC motors, please look at my sensored motor driver…... Listed under:
Motor Projects
752. An AVR Atmega based PID magnetic levitator This is a magnetic levitator implemented using Atmega8 microcontroller.
Magnetic levitation is a method by which an object is suspended with no support other than magnetic fields. To make a
magnet levitate, an hall sensor is attached to a coil. The coil acts as an…... Listed under: Sensor - Transducer - Detector
Projects
753. A led matrix Mask built on AVR ATmega8 AVR Mask1 is a led mask built around 74hc595 shift register and 8x8 led matrix. The "Dylan Dog" comics
decoupage, in conjunction with his stands, make it good looking.t has 4 8x8 led matrix, 2 for the mouth, and 2 for eyes. When the user…... Listed
under: LED Projects

754. A simple Sound Pressure Level Meter (SPL) dB audio meter using AVR ATmega A sound level meter or sound meter is an
instrument which measures sound pressure level. Sound pressure level (SPL) or sound level is a logarithmic measure of the
effective sound pressure of a sound relative to a reference value. It is measured in decibels (dB)…... Listed under: Sound -
Audio Projects
755. SD card logger library with log rotation that fits on ATmega8 This library implements an SD card Data Logger that runs on
ATmega. It has a small footprint, so it can be loaded on an ATmega8, leaving space for user code. It supports SD and
microSD cards formatted with FAT16. It also features log rotation.The "Petit FAT…... Listed under: Memory - Storage Projects
756. A Pickup Winding machine built on an ATmega8 The core of this project is an ATmega8. It features: wind counter slow startup
automatic stop configurable motor speed configurable winds 2 directions If you are looking for a CNC version: you can find it
here: http://davidegironi.blogspot.it/2016/06/a-cnc-pickup-winding-machine-built-on.html This winder has an LCD display
that will show…... Listed under: Motor Projects
757. USB AVR programmer I’ve already had a programmer for Atmel’s AVR microcontrollers, but I couldn’t use it in my lab,
because my laptop doesn’t have a LPT port. So I decided to make a new programmer with USB connection. I’ve found an
open source programmer AVR doper, and…... Listed under: LCD Projects
758. RSS Reader using AVR mega8 I spent part of an afternoon developing a hardware RSS reader (most of my time was spent on
the python side of things). It’s pretty simple and uses an AVR microcontroller connected to a computer via a serial cable
Hardware I am using the Dragon…... Listed under: LCD Projects
759. Veronica – VRAM I considered subtitling this article, “adventures in breadboard noise”, since that’s what I spent most of my
time dealing with. In any case, let’s recap where we were. Veronica’s video generator was generating a stable VGA signal. In
addition, a test pattern was being displayed…... Listed under: LCD Projects
760. RFID based security system using AVR ATmega32 microcontroller RFID technology brought a great revolution in our life as it
simplifies the machine communication. RFID’s are used almost everywhere today Schools, hospitals, industries and much
more. This article teaches you to build a simple RFID based security system using AVR microcontroller which is reliable…...
Listed under: Security - Safety Projects
761. AVR HVSP Fuse Resetter Description In working w/ 8 or 14 pin avr devices, I would sometimes want to use the RESET pin as io
as the io pin count is low. But doing so will disable further programming via SPI. I do not need a full blown HV…... Listed
under: AVR ATmega Projects
762. AVR Thermostat This thermostat is built around an ATMega164 and a TC1047A temperature sensor. It controls your furnace
and air conditioner. It is not programmable, although it has a clock and is capable if some additional code were written (any
volunteers?). The unique feature is that instead of a bunch of buttons…... Listed under: Temperature Measurement Projects

763. Building a Wifi Radio – Part 7, Building an LCD Display This is the seventh part of an ongoing series about building a low cost,
open source streaming internet radio. If you haven’t already, check out the previous parts (see the links at the end of this
article) for some background about the project. In part…... Listed under: LCD Projects
764. Reading temperature on AVR Atmega using a thermistor with NTCtemp library 02 A thermistor is a type of resistor whose
resistance varies significantly with temperature, more so than in standard resistors. NTCtemp is a simple AVR library to read
temperature from a thermistor connected to an atmega micro. The library implements three models convert adc value
read from analog…... Listed under: Temperature Measurement Projects
765. CMR Robot Arm Our project was mainly designed for the Cornell Mars Rover project team (CMR), which will be using the
robotic arm for competition to complete many different tasks in the deserts of Southern Utah. For our ECE 4760 final project,
we created the control systems for…... Listed under: Robotics - Automation Projects
766. AVR 16bit Stereo Wave Player Introduction This project aims to implement a cost-effective wave player based on AVR
(ATmega / ATiny Series) with CD-Audio Quality, which can play 8-bit/16-bit Mono/Stereo standard RIFF (Resource
Interchange File Format) wave files. This project can be applied into many applications such as bus /…... Listed under: Sound
- Audio Projects
767. Drive a stepper motor with acceleration and deceleration using an Allegro driver on ATmega8 The stepper motor is an
electromagnetic device that converts digital pulses into mechanical shaft rotation.Most common types of stepper motor can
be bipolar or unipolar, depending on the winding. To make a stepper motor move, motor windings must be loaded in the
correct order. A…... Listed under: Motor Projects
768. InLinea01: A PID controlled line following robot build on an ATmega 8 InLinea01 is a simple PID controlled line following
robot. This is not speed oriented line follower, this is just a prototype I built to experiment with this type or machines, though
it can be the first step to build a faster one. The goal of a…... Listed under: Robotics - Automation Projects
769. A DIY A4 Laser Engraver made from a scanner and a printer on ATmega328 This "Get Ready For Win98" Laser Engraving
Machine it's built using an old scanner, and an old printer. A laser engraving machine is a tool that uses lasers to engrave an
object. I've an old broken scanner and an old printer lying around. Inspired by this instructables…... Listed under: CNC -
Printing Machines Projects
770. CT Sensor on AVR ATmega A CT (Current Transformers) sensor is a device used to measure alternating current. A CT sensor,
like other current transformers is made by a primary winding, a magnetic core and a secondary winding. The primary winding
is often a single wire passing through the main…... Listed under: Sensor - Transducer - Detector Projects
771. A web configurable Xively logger, build on AVR ATmega328 Xively (formerly Cosm and before that Pachube) is a platform
devoted to simplifying the interconnection of devices and data with applications on the Internet of Things. It is an on-line
database service allowing developers to connect sensor-derived data (e.g. energy and environment data from objects,…...
Listed under: Sensor - Transducer - Detector Projects
772. Cheap CO2 meter using the MQ135 sensor with AVR ATmega MQ135 is an Air Quality Sensor suitable for detecting of NH3,
Alcohol, Benzene and other gases. The description below, is what i derive from the poor datasheet of this sensor, it may be
uncorrect, so if you have suggestions please leave me a feedback. The…... Listed under: Sensor - Transducer - Detector
Projects
773. A simple brushless sensored motor driver for AVR Atmega Brushless electric motor (BLDC motors) are synchronous motors
that are powered by a DC electric source via an integrated inverter/switching power supply, which produces an AC electric
signal to drive the motor. Additional electronics control the inverter output amplitude and waveform (and therefore percent
of…... Listed under: Motor Projects
774. PWM Motor Driver with MOSFET H-Bridge and AVR ATmega8 Here is a very simple project of controlling a small DC-motor
(taken from an old personal cassette player) with ATmega8. The ATmega8 is having three PWM channels, out of which two
are used here. PWM waveforms are fed to MOSFET (RFD3055) H-bridge. Here, direction is…... Listed under: Motor Projects,
PWM Projects

775. Atmel AVR ATMega16 Interfacing WIth 16×2 char LCD An alphanumeric low cost LCD Display is very essential for may small
and big projects to Display various type of information. Hitachi HD44780 Chipset based 16x2 char LCD is Really very cheap
and easily available in the local market. Project Description:- In this project we are going to…... Listed under: LCD Projects
776. An AVR-Based Microstepping Bipolar Chopper Stepper Motor Driver (STMD) Features Open Source - The schematic, parts list,
and software are all freely downloadable! Hobbyist-friendly - No surface mount parts means allows this drive to be easily
repaired! DMOS driver chips rated at 55V and 3 Amps. Easy parts availability - Electronic parts are all…... Listed under: Motor
Projects
777. LCD Interfacing with AVR Interfacing LCD Display in 8bit Mode I’ve already discussed about the LCD display in a note here in
this website. You can read the Note on character LCD Display here. Now let us come to the interfacing side of LCD. Let us see
the 8bit…... Listed under: LCD Projects
778. How to Establish A PC-Micro controller USART communication Introduction USART is one of the primitive inter-device
communication protocols. It is not used in modern computers. But still, a few mother boards come with the module
necessary for an USART communication. Here, in the case of PCs, the port is known as COM port…... Listed under: AVR
ATmega Projects
779. How to Interface an External EEPROM with AVR Atmega32 In this article, we will explain how to communicate to an external
EEPROM from the AVR Atmega32 MCU using the I2C communication protocol. So let’s begin our tutorial on how to interface
an EEPROM (AT24C16A) with AVR Atmega32.You will usually need an external EEPROM when…... Listed under: Sensor -
780. Worry-Free Automatic Timed Plant Feeder Description Do you often forget to irrigate your plants? Do you have to ask your
neighbors to take care of them when your whole families are out for a vacation? Don’t worry any more! Here is a solution.
This embedded system, worry-free automatic timed plant…... Listed under: LCD Projects
781. Week 11: Networking with ESP8266 For this week I set out to make a board that will show realtime MBTA bus arrival times
using the ESP8266 wifi module and a LCD. Seemed doable. People of the internet have been excited about the ESP8266
lately. Here is a snapshot of google…... Listed under: LCD Projects, Sensor - Transducer - Detector Projects
782. Color Video Game on AVR Introduction Our project is to make a color video game that runs primarily on the ATmega 1284P.
To do this, we adhered to the NTSC standard for color video. The sync signals used for NTSC are generated on the ATmega
1284P itself, and all game…... Listed under: Game - Entertainment Projects
783. Working with Atmel AVR Microcontroller Basic Pulse Width Modulation (PWM) Peripheral Pulse Width Modulation (PWM) is a
technique widely used in modern switching circuit to control the amount of power given to the electrical device. This
method simply switches ON and OFF the power supplied to the electrical device rapidly. The average amount of energy received…... Listed under:
PWM Projects
784. How to interface RFID with AVR ATmega32 microcontroller RFID is most arguably a evolutionary wireless technology which
boosted working of embedded devices up to great mark. And there is plenty of systems and devices working based on this
technology. This article is focused to teach you how to interface RFID with AVR microcontroller.…... Listed under: AVR ATmega
Projects
785. Remote Temperature Monitoring using GSM – AVR Project Temperature monitoring have wide application in daily life. In
modern day keeping an eye on temperature of places such as server rooms, hospital rooms, warehouses and green houses
can help solve many problems. But with the use of normal temperature sensors, someone needs to go…... Listed under:
Temperature Measurement Projects
786. ATMega16 AVR Microcontroller Seven Segment Digital Clock The ATMega16 Seven Segment Digital Clock In this ATMega16
AVR project we will be designing and implementing a digital clock with the aid of a Atmel AVR ATMega16 microcontroller
and Seven Segment Displays. As such before going through this digital clock AVR project it is…... Listed under: Clock Projects

787. Servo motor control using AVR Servo motors are so called “closed feedback” systems. This means that motor comes with
control circuit, which senses if motor mechanism is in desired location and if not it continuously corrects an error until motor
reaches proper point. Servo motors are widely used in robotics,…... Listed under: Motor Projects
788. Running TX433 and RX433 RF modules with AVR microcontrollers Sometimes in embedded design you may want to go
wireless. Might be you will want to log various readings of remotely placed sensors, or simply build a remote control for
robot or car alarm system. Radio communications between two AVR microcontrollers can be easy when…... Listed under:
789. Obstacle Avoiding Robot using AVR ATmega32 – Part II Hello and Welcome back to the second part of Obstacle Avoiding
Robot Tutorial. In the last part we studied the drive system and the mechanical construction of our robot. In this part we will
make the sensor part. The sensors will help our robot detect…... Listed under: Robotics - Automation Projects
790. Weeks 11-12: AVR USB Devices and Programming One of the relatively unexplored topics in this week’s lecture was USB, the
ubiquitous protocol that allows computers to communicate with peripheral devices (containing microcontrollers). Creating a
USB device allows any computer to talk to it without the specialized software and hardware we’ve been using…... Listed
under: Interfacing(USB - RS232 - I2c -ISP) Projects
791. Lab: DC Motor Control Using an H-Bridge Introduction Contents [show] In this tutorial, you’ll learn how to control a DC
motor’s direction using an H-bridge. To reverse a DC motor, you need to be able to reverse the direction of the current in the
motor. The easiest way to do this is…... Listed under: Motor Projects
792. Final Project: built a sous-vide immersion cooker For my final project I built a sous-vide immersion cooker: Sous-vide is a
method for cooking food in a temperature-controlled water environment for longer than normal cooking times, at an
accurately regulated temperature. Sous-vide cookers are often used in high-end restaurants. In the past few…... Listed under:
793. Arduino Robotic Arm In this tutorial, we design an Arduino Uno Robotic Arm. Entire arm will be designed from some scrap
material and servos. Entire process of construction has been explained in detail below. The arm has been built with
cardboards and the individual parts have been locked to…... Listed under: Robotics - Automation Projects
794. LED Blinking with ATmega32 Microcontroller Blinking LED is the first step you would like to take to get started with
electronics. In this tutorial we are going to connect an LED with ATmega32, which is an AVR series microcontroller. We are
going to blink the LED at half a second rate.…... Listed under: LED Projects
795. Interfacing LCD with ATmega32 Microcontroller To establish a good communication between human world and machine
world, display units play an important role. And so they are an important part of embedded systems. Display units - big or
small, work on the same basic principle. Besides complex display units like graphic displays…... Listed under: LED Projects
796. Power LED Dimmer using ATmega32 Microcontroller In this project we are going to use one of the features of ATmega32A to
adjust the brightness of 1Watt LED. The method that is used to adjust the speed of LED is PWM (Pulse Width Modulation).
The method of PWM is explained here. Consider…... Listed under: LED Projects, PWM Projects
797. Automatic Staircase Light We all know that one of the places where power wastage happens most in homes and offices is at
staircases. We usually turn on light at stairs and leave it in a hurry. In this project we are going to design a stair case lamp
which…... Listed under: Home Automation Projects
798. Microcontroller Based Electronic Voting Machine Whenever we go to vote for elections we come to see electronic voting
machines. In this project we are going to design and develop a simple voting machine by using ATmega32A
microcontroller. Although we can use the controller to get more than 32 people voting machine, to…... Listed under: AVR
ATmega Projects
799. RFID Based Toll Plaza System We know in offices, shopping malls and in many other places where only the person with
authorization card is allowed to enter the room. These systems use RFID communication system. RFID is used in shopping
malls to stop theft as the products are tagged with RFID chip…... Listed under: AVR ATmega Projects
800. 0-99 Counter using AVR Microcontroller In this tutorial we are going to design a 0-99 counter by interfacing two seven segment displays to
ATMEGA32A Microcontroller. Here we count events based on number of times button is pressed. Before moving ahead, let's understand what is a

seven segment display. A seven segment display…... Listed under: LED Projects
801. Temperature Measurement using LM35 and AVR Microcontroller In this project we are going to design a circuit for measuring
temperature. This circuit is developed using “LM35”, a linear voltage sensor. Temperature is usually measured in “Centigrade”
or “Faraheite”. “LM35” sensor provides output based on scale of centigrade. LM35 is three pin transistor…... Listed under:
802. RFID Based Voting Machine We know in offices, shopping malls and in many other places where only the person with
authorization card is allowed to enter the room. These systems use RFID communication system. RFID is used in shopping
malls to stop theft as the products are tagged with RFID chip…... Listed under: AVR ATmega Projects
803. 0-25V Digital Voltmeter using AVR Microcontroller In this project we are going to design a 25V range digital voltmeter by
using ATMEGA32A microcontroller. In ATMEGA, we are going to use 10bit ADC (Analog to Digital Converter) to build a digital
voltmeter. Now the ADC in ATMEGA can not take a input…... Listed under: Metering - Instrument Projects
804. Distance Measurement using HC-SR04 and AVR Microcontroller In this tutorial we are going to discuss and design a circuit
for measuring distance. This circuit is developed by interfacing ultrasonic sensor“HC-SR04” with AVR microcontroller. This
sensor uses a technique called “ECHO” which is something you get when sound reflects back after striking with…... Listed
under: Calculator Projects
805. Touch Keypad Interfacing with ATmega32 Microcontroller In this tutorial we are going to interface a 4x2 (8 key) touch keypad
with ATMEGA32A microcontroller. We all know keypad is one of the most important input devices used in electronics
engineering. This module does not have actual keys, but have specially designed capacitive metal pads,…... Listed under: LED
Projects
806. 4×4 Keypad Interfacing with ATmega32 Microcontroller In this tutorial we are going to interface a 4x4 (16 key) keypad with
ATMEGA32A microcontroller. We know that keypad is one of the most important input devices used in electronics projects.
Keypad is one of the easiest ways to give commands or instructions to an electronic…... Listed under: AVR ATmega Projects
807. Flex Sensor Interfacing with AVR Microcontroller In this tutorial we are going to interface FLEX sensor with ATMEGA8
microcontroller. In ATMEGA8, we are going use 10bit ADC (Analog to Digital Conversion) feature to do this job. Now the ADC
in ATMEGA cannot take a input more than +5V. [caption id="attachment_34862" align="aligncenter"…... Listed under: Sensor
808. Joystick Interfacing with AVR Microcontroller In this tutorial we are going to interface a joystick module with atmega8
microcontroller. A JOY STICK is an input module used for communication. It basically makes easy the user machine
communication. A joystick is shown in below figure. [caption id="attachment_34858" align="aligncenter" width="600"]
Joystick Interfacing with AVR Microcontroller[/caption]…... Listed under: AVR ATmega Projects
809. Anti-Theft Alert System using ATmega8 Microcontroller In this project we are going to make a vibration alert system with
ATMEGA8 microcontroller. This can also be used as a theft alert system, for that we are going to interface tilt sensor with
ATMEGA8. A tilt sensor is shown in below figure. [caption id="attachment_34853" align="aligncenter"…... Listed under: Sensor
810. 100mA Ammeter using AVR Microcontroller In this project we are going to make a low range ammeter using ATMEGA8
microcontroller. In ATMEGA8, we are going use 10bit ADC (Analog to Digital Conversion) feature to do this. Although we
have few other ways to get the current parameter from a circuit, we…... Listed under: AVR ATmega Projects
811. Light Intensity Measurement using LDR and AVR Microcontroller In this project we are going to interface LDR with ATMEGA8
microcontroller, and with this we can measure LIGHT INTENSITY in the area. In ATMEGA8, we are going to use 10bit ADC
(Analog to Digital Conversion) feature to measure the light intensity. Am LDR is a transducer…... Listed under: AVR ATmega
Projects
812. Fire Alarm System using AVR Microcontroller In this project, we are going to make a Fire Alert System using ATMEGA8
microcontroller and fire sensor. Fire sensor can be of any type, however we are using IR (Infrared) based Fire Sensor.
Although IR based Fire Sensors have some disadvantages mostly of inaccuracy, it…... Listed under: Security - Safety Projects
813. Alarm Clock using ATmega32 Microcontroller In this project we are going to design a simple Alarm clock using ATMEGA32 timers. ATmega32A
microcontroller has a 16 bit timer, and we will be using that timer to count the seconds and develop a digital clock. [caption id="attachment_34830"
align="aligncenter" width="650"] AVR Microcontroller Based Digital Alarm…... Listed under: Clock Projects

814. Introduction to Octocoupler and Interfacing with ATmega8 In this tutorial we are going to interface an Optocoupler
with ATMEGA8 microcontroller. Octocouplers are fascinating devices used to isolate the electronic and electrical circuits. This
simple device isolates the sensitive electronics from robust electronics like motors, yet keeping the load in control over the
source. [caption…... Listed under: AVR ATmega Projects
815. How to establish UART communication between ATmega8 and Arduino Uno? Here we are going to establish a
communication between an ATmega8 microcontroller and Arduino Uno. The communication established here is UART
(Universal Asynchronous Receiver Transmitter) type. It’s serial communication. By this serial communication data can be
shared between two controllers, which is a required in various embedded system…... Listed under: Android Projects
816. 8×8 LED Matrix Interfacing with AVR Microcontroller In this session we are going to design an 8x8 LED display with 8x8 LED
matrix and ATmega8 microcontroller, which can show alphabets or names. [caption id="attachment_34818"
align="alignnone" width="650"] LED Matrix Interfacing with AVR Microcontroller[/caption] A 8x8 LED matrix contains 64 LED
(Light Emitting Diodes) which…... Listed under: LED Projects
817. Make Your Own Homemade Arduino Board with ATmega328 Chip Arduino is an open-source development platform for
engineers and hobbyists to develop electronics projects in an easy way. It consists of both a physical programmable
development board (based on AVR series of microcontrollers) and a piece of software or IDE which runs on your computer
and used to write and upload…... Listed under: Arduino Programmer Projects
818. Scrolling Text Display on 8×8 LED Matrix using AVR Microcontroller In this tutorial we are going to design an 8x8 LED Matrix
Scrolling Display using ATMEGA32, which will show scrolling alphabets. 8x8 LED Matrix contains 64 LEDs (Light Emitting
Diodes) which are arranged in the form of a matrix, hence the name is LED matrix. We are…... Listed under: LED Projects
819. Atmega 32u4 Based USB Data Logger (Part 23/25) In this project, a device will be designed that will read analog data from
any analog sensor and will send the digitized form of that data to a personal computer on USB interface. On PC, a desktop
application will store the data in an excel…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
820. Controlling a BLDC Motor with an ESC REQUIREMENTS: 1. Microcontroller (AtMega 16) 2. A Brushless DC motor (BLDC) 3. An
Electronic Speed Controller (ESC) 4. Power source to drive the motor (LiPo battery) DESCRIPTION: Brushless motors have
much more satisfying results as compared to brushed motors. The basic difference between them is…... Listed under: Motor
Projects
821. AT89C2051 Development Stick 89C2051 Development Stick kit offers an easy way of interfacing 89C2051 compatible MCU’s.
Slim design with plug in type approach Voltage regulator on board for stable and regulated supply to the MCU RESET switch
for resetting the MCU 0592 MHz Crystal 4K external EEPROM Power-On…... Listed under: Development Board - Kits Projects
822. EGYDuino – Arduino compatible board EGYDuino is a DIY Arduino clone made on a single sided PCB board. It’s simple and
cheap to build using home PCB fabrication methods and it’s 100% compatible with Arduino. Description ATmega8 takes care
of the USB to serial communication and should be burned with…... Listed under: Android Projects
823. ATmega64 Development Board This project is a development board for Atmel ATmega64 microcontroller and can be used to
easily develop custom AVR firmware or as an introduction board to microprocessors and programming. A development
board is better to be used instead of a breadboard setup as it facilitates…... Listed under: Development Board - Kits Projects
824. DigiPot – Rotary Encoder Digital Potentiometer Description The “potentiometer” is actually a rotary encoder (TW-700198) connected to a
microcontroller that reads the signal from it and convert it to a value that is displayed on 7-segment displays. The value also is sent via
i2c/spi/serial/usb to the host. Also 3 LED and…... Listed under: AVR ATmega Projects

825. Atmega168 TV-B-Gone Yes, I know what you are thinking: "oh no, please not another TVBGone..." Anyway, this instructable is
for the newbies as me which are still experimenting with Arduino, and prefer to program an Atmega168 in Arduino than an
AtTyny85 with other methods. This circuit is…... Listed under: Home Automation Projects
826. Arduino atmega644/1284 clone This project is about to DIY an Arduino board wth an ATMEGA644P or 1284P to have more
INPUTS/OUTPUTS than on the atmega328P. You can buy an arduino mega but it's more expensive. The microcontrollers will
be bootloaded with Sanguino and the project seems to be…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
827. Small Footprint ATMega328P Board For my Word Clock project, for which I built a custom 8 x 8 LED Matrix with controller, I
needed a much smaller footprint DIY-Duino (board for an ATMega328P microprocessor), one that would have all of the main
functionality of my previous DIY-Duino boards (such…... Listed under: Development Board - Kits Projects
828. Flames effect with a 8×8 LED Matrix and ATMega328 A while ago I found some blog posts explaining how to use a LED
matrix as a pendant (http://hackaday.com/2013/01/10/8x8-led-matrix-pendant-sealed-in-a-block-of-epoxy/ and
https://sites.google.com/site/tinymatrix/ ). The 8x8 matrix pendant looked cool, but it was missing detailed information on
which parts to use and how to solder everything together.…... Listed under: LED Projects
829. Remote controlled switch using Atmega 328p Ever dreamt of controlling an appliance like a CFL or a fan at your finger tips
and thinking for a cheap solution? Well, then you are looking at the right instructable!! This instructable will provide you with
a cheap and best possible solution to control…... Listed under: Home Automation Projects
830. Easy Technique for Bootloading Atmega328pu and Atmega328p-pu# Xolcano it is very difficult to bootload Atmega chips
when you don't have proper knowledge about device signature ! each chips are associated with its own Signature.at the
beginning I found very difficult in uploading bootloader file to Atmega 328pu and Atmega 328p-pu , although their…... Listed
831. Digital Wall clock Using Atmega-8 and RTC Clock is one of the most essential house hold things. There are various types of
clocks like good old Pendulum clocks, Analog clocks and the now trending modern Digital clocks. Digital clocks has many
advantages over the analog clocks like the Accuracy in time, easy…... Listed under: Clock Projects
832. Running an HD44780 Display off the ATmega on a Gertboard There was a thread on the Raspberry Pi forums about running a
16x2 HD44780 based display off the ATmega chip on the Gertboard. I normally use a shift register to run my display, so I
wasn't much help to them. I decided to try and…... Listed under: LCD Projects
833. How to fix dead atmega and attiny avr chips Atmega fusebit doctor, as name says it, device for repairing dead Atmega and
Attiny family AVRs by writing fabric fusebits. Most common mistakes or problems are a wrong clock source (CKSEL fusebits),
disabled SPI programming (SPIEN fuse) or disabled reset pin (RSTDISBL fuse). This simple…... Listed under: How To - DIY -
Projects
834. Getting Started With the ATMega328P In the Internet of Things movement, people across the globe are connecting their stuff
– TVs, pets, even houseplants - to the internet and transmitting all sorts of data. If you’re going to be a part of that
movement, or want to dabble in creative…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
835. ATmega DIP40 Minimal Board After I wrote several articles about using ATmega microcontrollers (DIP40) in Arduino environment I had some feedback
that I was asked how to be effectively put into operation this project. As I came into the Arduino world from classical microcontrollers development
world, I have not…... Listed under: Development Board - Kits Projects

836. Program an ATmega168/328 with codebender If you want to use an inexpensive ATmega168 or ATmega328p for your project,
but you want the simplicity of the arduino code and codebender, this tutorial will guide you through! A brand new ATmega
microcontroller does not come preconfigured to use with Arduino code. So…... Listed under: Interfacing(USB - RS232 - I2c -
ISP) Projects
837. Alarm clock Using Atmega-328 and RTC Hi everyone! This is my first instructable! After reading hundreds of instructables, I
decided to make one myself. Clock is one of the most essential house hold things. There are various types of clocks like good
old Pendulum clocks, Analog clocks and the now trending…... Listed under: Clock Projects
838. Atmega Alarmclock & Thermohumidity meter First, let me introduce you my project. I made an Alarm clock with extended
functionality & thermometer and humiditymeter. Everything started when my friend (who used to bring me some old
electronic rubbish and I used to check if there's not something useful) brought me…... Listed under: Clock Projects, Metering -
Instrument Projects
839. Interfacing Analog Joystick with AVR ATmega32 If you have played games on console you must be knowing what a joystick is.
In games a joystick is generally used to control the motion of character or a vehicle (like plane or car). Joystick give a very
realistic two dimensional control! Joystick are…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
840. Working with TWI (I2C) sensors / Devices Introduction The I2C is a multimaster, multislave serial single-ended computer bus
and was invented by Philips in 1982. The atmel microcontrollers use a compatible to I2C serial bus that is named TWI (Two
Wire Interface). The TWI supports serial communication at 100 kHz and 400 kHz. The…... Listed under: Sensor - Transducer - Detector Projects
841. Boolean Algebra Calculator Power Supply: It can be defined as a device that supplies electrical energy to one or more electric
loads. The term is most commonly applied to devices that convert one form of electrical energy to another, though it may
also refer to devices that convert…... Listed under: Calculator Projects
842. Automatic Railway Gate Controller with High Speed Alerting System The main aim of this project is to operate and control
the unmanned railway gate in the proper manner in order to avoid the accidents in the unmanned railway crossing. In a
country like ours where there are many unmanned railway crossings, accidents are increasing…... Listed under: Security -
Safety Projects
843. Interfacing 16X2 LCD to AVR Microcontroller Well this is not different from the way interfacing the LCD to 8051 or PIC
microcontroller. The crystal oscillator will provide the clock to the microcontroller. The capacitors connected to the crystal will
act as filters and help the crystal to resonate and oscillates…... Listed under: LCD Projects
844. Water Level Indicator The Water Level Indicator employs a simple mechanism to detect and indicate the water level in an
overhead tank or any other water container. The sensing is done by using a set of nine probes which are placed at nine
different levels on the tank…... Listed under: Sensor - Transducer - Detector Projects
845. DTMF Controlled Home Automation System Circuit Generally, appliances used in our home are controlled with the help of
switches. These days, you can see automation of these appliances using many technologies. This article presents the
controlling of home appliances using DTMF technology. DTMF is acronym for Dual Tone Multi Frequency. So, just…... Listed
under: Blog, Home Automation Projects
846. 2 Digit Up/Down Counter Circuit Generally, one can see the digital displays which display the score when buttons are pressed on score boards. The
main heart of this score board is 2 digits up/down counter circuit. The 2 digits are displayed on two 7 segment displays. This article describes 2…...
Listed under: Calculator Projects

847. Digital Temperature Sensor Circuit Temperature sensors are widely used in electronic equipments to display the temperature.
You can see the digital clock displaying the room temperature value. It is due to the temperature sensor embedded in it.
Generally, temperature value is analog. It is converted to digital value and…... Listed under: Temperature Measurement
Projects
848. RFID Based Attendance System – Circuit, Working, Source Code Attendance in colleges is generally paper based which may
sometimes cause errors. Taking attendance manually consumes more time. So the proposed attendance system uses RFID
technology to take attendance. In this system, each student is issued an RFID tag. Controlling unit is in the institute.…... Listed
849. Auto Intensity Control of Street Lights treet lights are controlled manually in olden days. These days automation of street
lights has emerged. But one can observe that there is no need of high intensity in peak hours i.e. when there is no traffic and
even in early mornings. By reducing the…... Listed under: Sensor - Transducer - Detector Projects
850. Street Lights that Glow on Detecting Vehicle Movement Street lights are switched on depending on the intensity of the Sun
light on LDR. If the intensity of Sunlight on light dependent resistor is low, its resistance value is high. This value increases
and becomes high when it is completely in dark. This resistance…... Listed under: Sensor - Transducer - Detector Projects
851. Sun Tracking Solar Panel As the non renewable energy resources are decreasing, use of renewable resources for producing
electricity is increasing. Solar panels are becoming more popular day by day. We have already read a post about how to
install solar panel for home. Solar panel absorbs the energy…... Listed under: Sensor - Transducer - Detector Projects
852. Line Follower Robot using Microcontroller When robot is placed on the fixed path, it follows the path by detecting the line.
The robot direction of motion depends on the two sensors outputs. When the two sensors are on the line of path, robot
moves forward. If the left sensor moves…... Listed under: Robotics - Automation Projects
853. PWM Based DC Motor Speed Control using Microcontroller In many applications, it is important to control the speed of DC
motor where precision and protection are essence. Here we will use a technique called PWM (pulse width modulation) to
control the speed of DC motor. We can achieve speed control of DC motor…... Listed under: PWM Projects
854. Biometric Attendance System Circuit Biometrics is the emerging technology used for identification. Biometric refers to
automatic identification of a person based on biological characters such as finger print, iris, facial recognition, etc. In this
article finger print based attendance system is proposed. Attendance in educational institutions, industries will require…...
Listed under: Sensor - Transducer - Detector Projects
855. Temperature Controlled DC Fan using Microcontroller A Temperature Controlled DC Fan is a system which automatically turns
on a DC Fan when the ambient temperature increases above a certain limit. Generally, electronic devices produce more heat.
So this heat should be reduced in order to protect the device. There are many…... Listed under: Temperature Measurement
Projects
856. GSM Module SIM300 Interface with AVR Amega32 A GSM/GPRS Module like SIM300 can be used for any embedded
application that requires a long range communication, like a robot in Chennai controlled by a person sitting in New Delhi! Or
simply a water pump in a rice field turned on in the morning…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
857. Ultrasonic Rangefinder HC-SR04 Interfacing with ATmega8 In this article I will describe how to interface a Ultrasonic Range
Finder Module with a AVR ATmega8 microcontroller. I will provide a HEX file which you can burn into your ATmega8 directly
to quickly test this whole setup. Ultrasonic range finder modules helps find…... Listed under: Interfacing(USB - RS232 - I2c -
ISP) Projects
858. Simple Single Motor Control using AVR ATmega16 Microcontrollers are good when it comes to brain, but to do anything in real world they need
muscles too ! Their muscles are electromechanical actuators like motors. Their are several types of motor available to do various type of motion. The
simplest of them are…... Listed under: Motor Projects

859. AVR Dual RGB Matrix Driver Multiplexing LEDs can be tricky, but we're working with RGB LEDs, so think of each RGB as three
individual LEDs. For an 8 x 8 matrix, that is 192 total LEDs on a single matrix. Even though there are only 32 connection pins,
it is…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
860. AVR Chronograph from concept to PCB A chronograph is a device used to measure the speed of a passing object. In it's
simplest form, this involves two sensors of some kind that 'see' the object, some device that can measure time, and some
output to deliver the data to the user.…... Listed under: Development Board - Kits Projects
861. Running LED bicolor This is a good project for beginners. It is easy to build.This running LED light uses seven bicolor led's red
and yellow, they light up in a pattern that can be made within the program code.The program code is written in assembler.
ATMELs AVR STUDIO…... Listed under: LED Projects
862. LED thermometer his project shows the temperature on a three digit 7-segment display, it measures the temperature from
-9.5 to 99 degrees Celcius in 0.5 C steps, or from 0 to 210 degrees Fahrenheit in 1.0 degrees steps. Because of the LED display
the temperature is also…... Listed under: LED Projects, Temperature Measurement Projects
863. LCD interface This example is based on a LCD module with the Hitachi HD44780 LCD-controller.You can get these displays in
various kinds, from 1 to 4 lines and from 8 to 40 characters per line. A display with 16 characters per line and 2 lines is used
in…... Listed under: LCD Projects
864. RGB LED color mixer Page 1 of 4 An RGB LED is a LED which has three LED's integrated in one packaging. These LED's have
the colors Red, Green, and Blue. The RGB LED used here is a hyperflux LED with common cathode, which can draw 20mA
current. Such a…... Listed under: LED Projects
865. Stepper motor driver With this circuit you can drive a unipolar stepper motor. It operates in full step mode. The AVR
attiny2313 micro controller controls the pulses for the stepper motor. The pulses are amplified by the ULN2003 driver. The
driver accepts 5V inputs, the output for the…... Listed under: LED Projects
866. LED VU meter Schematic and build Below is the schematic of the LED VU meter. The circuit is builds with the ATMega328
board an two LED boards connected to it. You can also build it on a breadboard. For more detail: LED VU meter... Listed
under: LED Projects
867. Temperature indicator This project uses a Dallas DS1621 temperature sensor which indicates the temparature of the device.
The temperature sensor has an thermal alarm output, which becomes high when the temperature of the device exceeds a
user defined value. When the temperature drops below a user defined…... Listed under: Temperature Measurement Projects
868. Running LED's using ATTiny2313 This running LED or LED chaser is a good project for beginners in the microcontroller technology. It is easy to build,
and the assembler program code can be easily adapted. This running LED light has 15 red 3mm LED's. The 15 outputs of ports B and…... Listed under:
LED Projects

869. Running LED's This small project let you make running leds. For this project you need a attiny2313 microcontroller and 8 leds
and 8 resistors. The leds can be programmed so that they show differrent patterns. Hardware The leds are connected to
PORTB of the microcontroller via the…... Listed under: LED Projects
870. PC stepper motor driver With this circuit you can control two unipolair stepper motors in full step mode via the RS232 serial
port of your PC. A terminal program such as Hyperterminal can be used to control the stepper motors. The stepper motors
can be driven one at a…... Listed under: Motor Projects
871. Photocell or LDR A photocell or photo resistor is a Light Dependent Resistors (LDR). LDR's are sensors that detect light. They
are small, inexpensive, low-power, easy to use and don't wear out. Overview A photocell or photo resistor is a Light
Dependent Resistors (LDR). LDR's are sensors that…... Listed under: Sensor - Transducer - Detector Projects
872. Electronic cricket his electronic cricket is a fun project. A real crickets chirp at night and faster in warmer temperatures. A
cricket chirp is composed of a group of three sinus waves of a single frequence of about 5kHz. occurring in rapid succession.
Introduction This electronic cricket is…... Listed under: Game - Entertainment Projects
873. Relais Driver Board This is a peripheral board with 4 relais, rated at 5A/250V each. The board has a ML10 output connector
for connection with the AT2313 Project board. It has also 4 LED's for indication which relais is switched on. Hardware The
circuit is simple, it consists…... Listed under: Development Board - Kits Projects
874. Dot matrix display This is a Dot Matrix Scrolling Sign. A Dot Matrix Display has an 5x7 led matrix with 5 columns and 7 rows.
The display is controlled by the ATMega328 microcontroller board. The rows are controlled by PORTB of the microcontroller,
while PORTD puts the data…... Listed under: LED Projects
875. Clock/temperature LED display This project is based on the timer/counter 0 example. It shows time, date and temparature on
7 segment displays. Instead of the LCD display the time is shown on a four digit 7 segment display with common cathode.
The date and temparature is shown on…... Listed under: Clock Projects
876. LCD/switch interface Page 1 of 2 This board can directly connected to the STK 500 board or the ATTiny2313 ISP program
board with a 10 pole flatcable on the 10 pin header of the STK500 and the 10 pin header of the LCD/Switch board. The
display has…... Listed under: LCD Projects
877. Digital Book Cricket with ATtiny 85 The project described here is a digital implementation of “book cricket game” which
students normally use to play in their childhood time. The heart of the project is 8 bit MCU from AVR family called ATtiny85.
ATtiny85 are small and cheap microcontrollers which are convenient…... Listed under: Game - Entertainment Projects
878. Attendance System using AVR and RFID This project aims to automate the process of taking attendance on pen and paper
and prevent any fraudulent entry. It uses RFID tags to record attendance. Each student is assigned a unique tag, which he/she
is required to swipe over the reader to give his/her…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
879. Interfacing Serial Bluetooth Modem with Computer using ATmega16 This article would give you a general idea about how to
setup and interface any Bluetooth modem with your computer. There are many types of Bluetooth modems available in
market, which vary in quality, cost, range, etc. Some of the well known Serial Bluetooth modems…... Listed under:
880. Smart Home Automation using AVR in this technological world, automatic systems are being preferred over manual system. In this series Home
Automation plays an important role for humans. In this unit we talk about basic needs to understand the project well and also for its future
advancements. We are going…... Listed under: Home Automation Projects

881. Interfacing 4-wire Resistive Touchscreen with ATMega16 Microcontroller Touch screens are two dimensional input devices.
Nowadays most of the electronic gadgets use them. Laptops, smart phones, tablets and even some home appliances like
washing machines & microwave ovens also use a touch screen nowadays. Why Touch screens? Touch screens are preferred
over keypads…... Listed under: LCD Projects
882. How to Interface a GSM (SIM 300) Modem with ATmega32 to Send and Receive SMS What is a GSM Modem? GSM stands for
Global System for Mobile Communications.It is a standard set developed by the EuropeanTelecommunications Standards
Institute (ETSI) to describe protocols for second generation (2G) digital cellular networks used by mobilephones. A Modem is
a device which modulates and…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
883. AVR I/O Ports AVR microcontrollers are the advanced microcontrollers. From 1996 onwards these are come into existence. In
AVR family there are so many controllers are available. Mainly the AVR family is sub grouped as ATmega, ATtiny, Xmega, UC3,
SAM3 and SAM4. In these form 8 to 32…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
884. Fastest Finger First Circuit using ATMega16 Fastest Finger first circuit is basically used in quiz type games where the reaction
speed of a participant is significant. The circuit enables us to identify who responded first to the question by triggering a
visual and audio indication. Components Required 1 x ATMega16 development…... Listed under: Game - Entertainment
Projects
885. DIY: Retro Style Analog Volt Meter using Servo Motor Digital equipments have rapidly replaced Analog equipments in the
long run. Well that is because the former has lot of advantages over the latter. But do you miss those retro style analog
measuring instruments? Those pointy indicators and graduated scales? Well I do and so…... Listed under: Metering -
Instrument Projects
886. embRACE: The Embedded Race embRACE, a game developed on the embedded platform, entirely coded in assembly
language. The game has been programmed on an ATMega16 micro-controller, interfaced with a 16x2 LCD display module.
The game possesses an interactive user interface and exclusive features like: -Main Menu -Pause Menu -Real…... Listed under:
Interfacing(USB - RS232 - I2c -ISP) Projects, LCD Projects
887. Latitude & Longitude Display System Using GPS & AVR Microcontroller This project is a reference to budding engineers or a
helping hand to those who willing to work and interface a GPS Receiver with microcontrollerand making their own channel to
communicate with satellite, seeking for some useful information from satellite to make a effective and…... Listed under: GPS
Based Projects
888. Controlling RGB LED colour using Atmega16 This tutorial will give you a brief introduction to the concept of colors and how
different colors can be produced using RGB LED. The color would be controlled using an ATMega16 microcontroller. RGB
LEDs are basically the combination of the 3 LEDs (Red, Green and…... Listed under: LED Projects
889. Speed and Direction Control of Stepper Motor using AVR Microcontroller Stepper motor can be termed as digital motor
because it operates on pulses. Unlike AC or DC motor that rotates continuously, stepper motor rotates in steps. It rotates in
number of steps as per applied number of pulses. Stepper motor is used in many applications…... Listed under: Motor
Projects
890. Accelerometer Based Hand Gesture Controlled Robot In many application of controlling robotic gadget it becomes quite
hard and complicated when there comes the part of controlling it with remote or many different switches. Mostly in military
application, industrial robotics, construction vehicles in civil side, medical application for surgery. In this field…... Listed under:
891. Digital Clock using Seven Segment Display and ATMega16 In this ATMega16 AVR project we will be designing and
implementing a digital clock with the aid of a atmel AVR ATMega16 microcontroller and seven segment display. Before going
through this digital clock AVR project it is recommended to complete the tutorial on Interfacing a Seven Segment Display
with…... Listed under: Clock Projects

892. LED Light Bulb Controller using AVR Microcontroller Previously before 10-15 years the majority of electrical lights were either
light bulbs (with yellow light) or tube-light sticks (with white light). The major disadvantage of these lighting devices was they
consume more electrical energy (in terms of Watt) and gives less luminance (brightness). Light…... Listed under: LED Projects
893. Speed and Direction Control of DC Motor using AVR Microcontroller Controlling direction and speed of DC motor is very
essential in many applications like· Robotic application – to change direction and speed of moving robot· Industrial
application – to change direction and speed of rotating machinery· Domestic application – to vary speed of battery
(DC)…... Listed under: Motor Projects
894. 4 Wire Touch Screen Based Digital Magic Slate Ever played with magic slates in your childhood? Well this project will show
you how to make a digital magic slate using a PC, a touch screen and few other components. Components Required
1. 4-wire resistive touch screen with connector 2. ATMega16…... Listed under: LCD Projects
895. Intelligent LED light controller using AVR Now a days LED light bulbs are becoming more and more popular because they
have several advantages. Some of their advantages are listed below · Their energy (electrical) consumption is much
more less · Their luminance is more · Their intensity can be varied · …... Listed under: LED Projects
896. DC Motor Control with Joystick & AVR Microcontroller In many of the applications it is required to alter the direction of DC
motor instantly. Like in washing machine, mixer, drilling machine winding – rewinding machine etc. Changing the direction of
DC motor using joystick is most suitable and handy method. Joystick Control for…... Listed under: Motor Projects
897. GSM Based Intruder Alerting System Did you know that most of the thefts at home happen when it is empty? But not
everyone is rich enough to hire a security for their house and at the same time they themselves cannot be at home 24x7.
Now what if there is…... Listed under: Phone Projects
898. GSM Based AC Appliance Control This project would show you how to control an AC appliance remotely from anywhere
using your mobile phone. This kind of project is useful in various applications. Say for example a farmer can switch ON or OFF
the motor pump present near his field remotely.…... Listed under: Phone Projects
899. Cell Phone Controlled Pick and Place Robot Conventionally, wireless controlled robots uses circuits, which have a drawback of
limited working range, limited frequency range and limited control. Use of mobile phones for robotic control can overcome
these limitations. It provides the advantages of robust control, working range as large as the coverage…... Listed under:
900. Light Tracker Demonstration Electricity is the most required and important element of human life. We cannot imagine our
day to day life without electricity. Electricity is generated using conventional (coal, diesel) and non conventional (water, wind,
sunlight) energy sources. The recent and latest trend is to generate electricity…... Listed under: Metering - Instrument Projects
901. Variable Power Supply with LCD Are you an electronic hobbyist? Then an adjustable power supply is a must for your various
needs. This project explains how to make a LM317 based adjustable power supply unit with a digital display. Components
Required 1. LM317 IC 2. Resistor – 240 Ohms 3. …... Listed under: LCD Projects
902. Interfacing Triple-Axis Accelerometer with AtMega16 Requirements AtMega 16 IC/development board 3-Axis accelerometer
LCD screen 16X2 (for displaying X, Y and Z data) Description This project makes use of three out of the eight ADCs present in
AtMega16 IC to display the corresponding digital data of X, Y and Z outputs…... Listed under: Interfacing(USB - RS232 - I2c -
ISP) Projects
903. Atmega32 avr based Drone Quadricopter atmega32 avr based Drone Quadricopter:IntroductionOur project is a novel hand
held controller in which we use an accelerometer to wirelessly control the motion of a Parrot AR Drone
Quadricopter.Rationale:The main idea of our project was building a cool glove controller for a flying platform, a…... Listed
under: Drones
904. Audio Tone Generator using AVR Microcontroller The circuit presented here demonstrates how to generate Audible Frequency from an AVR
Microcontroller. The output of Microcontroller is always digital so to generate audible sound at the outset first it needs to be converted into Analog. A
DAC (Digital to Analog Converter) is used…... Listed under: Sound - Audio Projects

905. Stepper Motor Angle Control using AVR Microcontroller There are many applications in which it is required to set the
position of an object at a desire angle. Some of the examples are 1. Satellite Dish Antenna positioning The Satellite Dish
Antenna should be in straight alignment with Satellite in Space to receive…... Listed under: Motor Projects
906. Bluetooth Controlled Portable LED Display The aim of the project is to make a portable LED display from SMD LEDs and to
display the custom programmed patterns at our command. The core application of the project is to act as a portable display
for event organisers or exhibitionists or consultants to…... Listed under: LED Projects
907. Coin Operated Timer Control Power Supply Box to Control AC Appliances Saving electricity is a major concern for domestic
and industrial units. We always try hard to save electricity in many ways to reduce our electricity bills, but due to some known
and unforeseen circumstances our efforts do not normally transform in saving electricity. Adding to…... Listed under: LCD
Projects
908. Sleeping Security – Smart Keypad Lock using AtMega16 This project is just a smart version of any keypad lock. What’s smart
about it is that it can detect whether it is needed by the user or not and accordingly switches itself to take a sleep. Making a
microcontroller to sleep reduces power consumption…... Listed under: Security - Safety Projects
909. DIY – Waveform Generator using AVR Microcontroller To interface 8-bit DAC with AVR microcontroller ATMega32 and
generate different waveforms like Square Wave, Sine Wave, Triangular Wave, Staircase Wave and Saw-tooth Wave.
Instruments · AVR Development Board · ADC – DAC card · Digital Storage Oscilloscope (DSO) · Power
Supply Apparatus · Connecting…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
910. Fully Customized Device On/Off Timer Timers are used in many different applications for example in Industrial Applications,
to switch ON or switch OFF any device or a machine load for a specific period of time. In the same way the timers are used in
Domestic Appliances like in Air Conditioners,…... Listed under: Clock Projects
911. Mobile – Gesture Controlled Car REQUIREMENT: AtMega 16 microcontroller L293D motor driver IC Bluetooth module (HC05)
Chassis Motors & Wheels Mobile phone (Android + Bluetooth compatibility) Battery (for car section) DESCRIPTION: Have you
ever wondered of operating a toy car with you own mobile phone? Yes I have made such…... Listed under: Car Projects
912. Un-interruptible Bench-top DC Power Supply With Display This tutorial explains how to make your own power supply unit for
all your electronics andembedded system experiments. It also has a backup battery which will be used in case of power cuts
and a display. Components Required 1. SLA 12V battery 2. Banana Jack…... Listed under: LCD Projects
913. Fingerprint Detection using Microcontroller REQUIREMENTS: AtMega 16 Microcontroller (development board) Fingerprint
scanner module (R305) 16X2 Alphanumeric LCD (for user display) DESCRIPTION: In today’s secure world biometric safety is
on the top. Unlike other techniques which make use of passwords and numbers, that are needed to be remembered,
biometric techniques…... Listed under: LCD Projects
914. How to display text on 16×2 LCD using AVR microcontroller (ATmega16) This article is in continuation to the article Single
character LCD display using AVR. The aforesaid article shows how to display a single letter on LCD. Moving forward towards
learning to work with LCD, this article explains how to display a string on LCD. Displaying…... Listed under: LCD Projects
915. Display custom characters on LCD using AVR Microcontroller (ATmega16) This is the most interesting article to play with LCD.
After going through the article, you can create any character/symbol which cannot be created using the ASCII values for
example smiley. You can even create small games. Conventionally 16X2 LCD is use to display text…... Listed under: LCD
Projects
916. How to use inbuilt ADC of AVR microcontroller (ATmega16) Microcontroller understands only digital language. However, the inputs available from the
environment to the microcontroller are mostly analog in nature, i.e., they vary continuously with time. In order to understand the inputs by the digital
processor, a device called Analog to Digital Converter (ADC) is…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects

917. Serial communication (Data receive) using AVR Microcontroller (ATmega16) USART Communication between two entities is
important for the information flow to take place. In general the information transport system can be parallel in which the
complete byte of data is sent at a time, with each bit having a separate dedicated line or it can…... Listed under:
918. How to interface AVR microcontroller with PC using USART (RS232 protocol) This article covers data transmission using 8 bit
USART. The readers should have a basic understanding of serial communication and how to receive the serial data output.
More details on these topics are available on Serial communication using AVR Microcontroller USART. The registers of
USART…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
919. Serial communication with AVR microcontroller using interrupts In our previous articles on serial data transmission using AVR
microcontroller we have demonstrated serial communication using the polling method. In Polling, the microcontroller waits
for the RXC flag (in the case of serial receiver) to go high and then moves to the next instruction.…... Listed under:
920. How to interface RFID with AVR microcontroller (ATmega16) Knowingly or unknowingly the RFID technology is used by us in
our day to day life. The most familiar example is seen in MNCs, schools and offices for daily attendance or automatic door
opening system. The RFID contains two parts, namely, tag and receiver modem. When…... Listed under: Interfacing(USB -
921. RFID interfacing with AVR microcontroller (ATmega16) using interrupts This article covers how to extract and display the
twelve byte unique tag ID received by RFID module on LCD using interrupt method. Before proceeding to this article readers
must have knowledge of serial interrupt and LCD. In the previous article of RFID, polling method…... Listed under:
922. How to use internal ADC of AVR microcontroller using interrupts This article is in continuation to AVR interrupts. There are
two types of interrupts external and internal in AVR microcontroller. The aforesaid article covers external interrupts. AVR
microcontrollers have seventeen internal interrupts. These internal interrupts are generated by the internal peripherals of
Microcontroller like Timer,…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
923. How to use inbuilt analog comparator of AVR microcontroller Analog comparator is a device which compares two input
voltages and generates output accordingly. The article on IR sensor explains the use of comparator in sensor designing.
Comparators form an integral part of circuit designing in majority of the applications. AVR microcontrollers have in-built
analog…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
924. How to disable JTAG of AVR microcontroller JTAG stands for “Joint Test Action Group” which was standardized as
the IEEE 1149.1 Standard Test Access Port and Boundary-Scan Architecture in 1990. JTAG is generally used in IC debugging
and device programming. Atmega16 consists of one JTAG port which shares four pins with PORTC. Until JTAG port…... Listed
925. How to interface LCD in 4 bit mode with AVR microcontroller This article explains interfacing of LCD with ATmega16 using 4-
bit mode. In this mode only four pins are used for sending data and command instructions. This mode has the advantage
over the 8-bit mode as it uses less number of pins. The remaining pins of…... Listed under: LCD Projects
926. SPI (serial peripheral interface) using AVR microcontroller (ATmega16) There are different protocols for serial communication
between two deceives like, USART, SPI, I2C etc. Before selecting any communication protocol, data transfer rate is an
important parameter. SPI transfers data at high speed data. AVR microcontroller contains on chip SPI interface. This article
will explore…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
927. How to use fast PWM (Pulse Width Modulation) Mode of AVR microcontroller Timer This article is in continuation of PWM
generation using AVR timer. In the previous article, PWM generation using Phase correct PWM mode is described. However,
there are some applications like DAC, power regulation and rectification etc. which require high frequency PWM wave. The
PWM generation…... Listed under: PWM Projects

928. Phase Correct PWM (Pulse Width Modulation) Mode of AVR microcontroller Timer Pulse Width Modulation is well known
technique for controlling power electronics devices like SCR, IGBT etc. PWM is also used in motor speed controlling. Square
wave generation by using AVR timers is explained in previous article. The AVR timers have feature of PWM wave
generation…... Listed under: PWM Projects
929. Waveform Generation using AVR Microcontroller (Atmega16) Timers At times we come across applications or situations
wherein we need to generate square waves with the microcontroller. The square wave can be generated by programming a
pin which toggles between 0 and 1 with a certain time delay. Alternatively, the inbuilt feature of AVR…... Listed under:
930. Serial communication (USART) with different frame size using AVR microcontroller The previous article explains serial
communication using 8-bit data transfer. AVR microcontroller also supports serial data transfer with frame size of 5, 6, 7 and
9 data bits. The size of data frame can be adjusted according to application. For example, consider a system that…... Listed
under: LCD Projects
931. How to use External (Hardware) Interrupts of AVR Microcontroller (ATmega16) This article introduces the concept of
interrupts and the different types of interrupts in AVR Microcontroller (ATmega16). Interrupt as the name suggests, interrupts
the current routine of the microcontroller. Microcontroller executes instructions in a sequence as per the programs.
Sometimes there may be a need…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
932. How to interface LED with AVR Microcontroller (ATmega16) ATmega16 has 32 I/O pins to communicate with external devices.
Before interfacing with external devices, these pins must be cofigured as input or output pin. This article demonstrates the
basic I/O operation of ATmega 16 using LEDs. All the four ports can be configured to…... Listed under: Interfacing(USB -
933. How to interface keypad with AVR microcontroller (ATmega16) Keypad is most widely used input device to provide input
from the outside world to the microcontroller. The keypad makes an application more users interactive. The concept of
interfacing a keypad with the ATmega16 is similar to interfacing it with any other microcontroller. The article…... Listed under:
934. How to interface Servo Motor with AVR Microcontroller (ATmega16) Servo motors find huge applications in industries in the
field of automation, control & robotics. The servo motors are well known for their precise control and work on the principle
of servo mechanism. The servo motors can be made to run at precise angle using…... Listed under: Motor Projects
935. How to use I2C / TWI (Two Wire Interface) in AVR ATmega32 This article explores the TWI interfacing between two ATmega32
controllers. Readers are advised to go through TWI Communication and TWI registers of ATmega32 before going further. TWI
works in four modes: 1. MASTER as a transmitter. 2. MASTER as a receiver. 3. SLAVE as a…... Listed under:
936. How to take input from a particular pin of ATmega16 For understanding the human needs a system must be able to take
input from user. The devices which can be used to take input for a system are keypad, touch screen, etc. In the article LED
blinking, the microcontroller drives the LED or in embedded language…... Listed under: Interfacing(USB - RS232 - I2c -ISP)
Projects
937. How to interface serial ADC0831 with AVR microcontroller (ATmega16) ADC is an electronics device that converts the analog
signals to digital number proportional to the magnitude of voltage. The ADC chips like ADC0804, ADC0809 etc., give 8-bit
digital output. The controller device needs eight pins to receive the 8-bit data (For more details about…... Listed under:
938. How to configure Watchdog Timers of AVR Microcontroller (ATmega16) Some high end applications require multiple or
critical calculations to be done by the microcontroller. This may lead to cases when the controller enters into wrong or
infinite loops. As a result of this, the system either hangs up or gets crashed. The solution to…... Listed under: Clock Projects
939. How to interface GPS with AVR microcontroller (ATmega16) GPS modem is a device which receives signals from satellite and
provides information about latitude, longitude, altitude, time etc. The GPS navigator is more famous in mobiles to track the
road maps. The GPS modem has an antenna which receives the satellite signals and transfers…... Listed under: GPS Based
Projects
940. Interfacing SD Card with AVR Microcontroller This project explains how to interface the SD card with an AVR microcontroller. In this project
an ATMEGA16 microcontroller is used. The microcontroller runs on 5V power supply with a built in crystal frequency of 8 MHz. A 2GB SDSC card from

Transcend is used in this particular project,…... Listed under: Memory - Storage Projects
941. How to Program in Boot Loader Section In the AVR microcontroller the flash memory is divided into two parts, namely
Application Section and Boot Loader Section. A code can be programmed into either the Application Section or the Boot
loader Section (BLS). The code programmed into the Application section runs normally and…... Listed under: LCD Projects
942. How to Initialize Peripherals from Boot Loader Section In almost all the microcontroller codes the peripheral initialization
functions like uart initialization, spi initialization are written along with the different application codes. These initialization
functions are actually repetitions of the original initialization functions. The same is the case with the external hardware
initialization like…... Listed under: LCD Projects
943. How to Use SPM for Flash to Flash Programming The Self Programming Mode (SPM) is a feature which enables a
microcontroller to program its own flash memory. Using the SPM a microcontroller can program itself with an SPM code. The
SPM is commonly used with the microcontroller Boot-Loader codes which help to program the…... Listed under:
944. How To Use SPM To load Application from EEPROM In any microcontroller the Boot-Loader is the first code which executes
before the application code does. The major function of the Boot-Loader is to load the application code into the flash
memory of the microcontroller and execute it. In AVR microcontroller the Self Programming Mode…... Listed under: LCD
Projects, Memory - Storage Projects
945. How To Write a Simple Bootloader For AVR In C language The BootLoader is a code which executes when a microcontroller is
powered ON or reset. It basically sets an environment for the application code to execute. It is the Boot-Loader that sets the
hardware and loads the application code from any storage medium or received…... Listed under: LCD Projects
946. LCD Scrolling Display Module A microcontroller is a device which has an inbuilt processor surrounded by few dedicated
hardware modules. Once the microcontroller initializes them they start operating on their own. In case of an ADC it will do
the sampling and digital to analog conversion all by itself…... Listed under: LCD Projects
947. Electronic Voting Machine using Internal EEPROM of AVR The microcontroller based voting machines made the process of
voting and counting the voted lot easier than before. Previously the votes were marked in paper which are then stored safely
in a box and inside a well secure room for days. The process of separating…... Listed under: LCD Projects
948. Setup Arduino Software for Atmega328P with Internal Crystal on Breadboard A breadboard Arduino will require an
Atmega328P controller for these instructions. Note the “P” at the end of the name. You cannot use an Atmega328 because it
has a slightly different device id number. It will require a different board configuration. Instructions for that are…... Listed
949. Playing video on nokia color LCD using an ATmega32 video Playing video on nokia color LCD using an ATmega32 Hi, I am introducing my new video
player made using an atmega32 microcontroller and nokia color LCD. I got a 65K color LCD from an old nokia 6030 mobile phone. I directly soldered
10 thin…... Listed under: LCD Projects
950. Make yourself a homemade clock with thermometer using ATMEGA128 In this step by step I wanna share my experiment
with ATMEGA128 timer and interrupt using DS1307 and NTC to display homemade clock and thermometer. It displays
hour,minute,second, day of week, day of month, month, and year, and the temperature in celcius Enjoy the project...…... Listed
under: Clock Projects, Home Automation Projects

951. MultiFunction LED Game Using An ATmega32 Microcontroller First are my answers to the Make-To-Learn Contest: What did
you make? I made a multi-function LED Array Program, like my previous one with Arduino UNO, but this time I made it with
an ATmega32 microcontroller. I used regular C code to program it and…... Listed under: LED Projects
952. Burn Arduino Bootloader on Atmega-328 TQFP and DIP chips on Breadboard Parts required (Hardware) Arduino Uno Board
(1) TQFP 32 to DIP 28 Adapter (1) Link Atmega TQFP 32 pin chip (1) Atmega DIP 28 pin chip (1) 10K resistor (1) 16MHz crystal
(1) 18pf - 22pf capacitor (2) Tact Switch (1) Jumper wires (few) LED…... Listed under: Other Projects
953. Burn BootLoader into Atmega328P using Arduino Diecimila I have an old Arduino Diecimila and some new Atmega328P-PU
chips. Shouldn't have but I brounght some without bootloader to save some dollars. What next? search instructables to see if
I can burn bootloader to ths chips. Unluckily not working. An error message "avrdude: stk500_getsync():…... Listed under:
Other Projects
954. Bootloading and Mounting Arduino Atmega328 – I made it at TechShop This Instructable shows how to bootload and mount
an Atmega328, Atmega328p or Atmega328p-pu for any project. This is a great way to save money by purchasing Atmega328
DIP package microcontrollers instead of using the Arduino development board itself. I put this together at techshop to…...
955. Use ATmega328 Chip as a Storage Device and Store Text and Images in it Hi everyone! In this instructable, I am going to show
you how to store text and images in a small ATmega328P chip. Lets get started! This article is also available on Jordan's Lab
Notebook! Step 1: Things Needed Things Needed: - Arduino Uno - ATmega…... Listed under: Other Projects
956. Create yourself a message flasher with ATMEGA128 Guys, I wanna share my experiment on creating a message flasher with
ATMEGA128 and LCD 16x2, It can be done on your weekend.... Step 1: Prepare the components I prepare all the components
below, The most importants are ATMEGA128 TQFP 64 and LCD 16x2 Another…... Listed under: Other Projects
957. Atmega16/32 Development Board With LCD This instructable shows, how to do your own development board for Atmega16
or Atmega32 processors.The Internet is full of home made development boards, but I think that, there is room left for
another one. This board have been very useful on my projects and I…... Listed under: Development Board - Kits Projects
958. RGB Rotary Encoder with PWM and ISRs Using an ATmega328 Description A long time ago I bought a couple RGB rotary
encoders from Sparkfun because they were cheap and I was already spending a bunch on other stuff. I thought they would
be neat for some interfaces since it includes a push button. The interrupt service…... Listed under: PWM Projects
959. Make yourself a speaking ATMEGA128 Guys, In previous weekend, I made myself a speaking ATMEGA128. I used ATMEGA128
and LM386 as an amplifier, Let's get started Step 1: The part I need for this project These parts are needed for this project : 1.
LM386 2.ATMEGA128 3.USBISP 4.AVRStudio 5. Small…... Listed under: Sound - Audio Projects
960. I2C Bus for ATtiny and ATmega I love the Atmel AVR microcontrollers! Since building the Ghetto Development System
described in this Instructable. I've had no end of fun experimenting with the AVR ATtiny2313 and the ATmega168 in
particular. I even went so far as to write an Instructable on using switches…... Listed under: Other Projects
961. Interfacing GY 26 with atmega640 Hello friend once again with new instructable in this I will show you how to interface GY 26
with UART when I started working on this very less resource where availble over internet .Thus i thought to share my piece of
work .GY 26 is…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
962. Using Atmega32 with Arduino IDE Over time I have used all kinds of Atmel microcontrollers in various projects. One of the most suitable was
ATmega32. I have a small collection of development boards for Atmega32/16, some bought as-is, some made on stripboard. Although the original

Arduino boards offers a pleasant…... Listed under: Other Projects
963. Standalone Arduino / ATMega chip on breadboard Step 1: Parts needed I bought my parts from Digikey and Sparkfun
Electronics - they're 2 of my favorite places to buy components. Anyway, here's the list: #1 - (Qty: 1) - ATMega328 chip with
Arduino bootloader pre-installed ($5.50) #2 - (Qty: 1) - 5VDC Switching…... Listed under: Development Board - Kits Projects
964. Burning atmega328-pu and atmega328p-pu bootloader Burning the boot loader in an atmega328 could be somewhat tricky
but if u follow these steps correctly youll be able to bootload any type of atmega328 micro controller .. Step 1: "setting up
the hardware" -List of stuff you'll need: - An Arduino board…... Listed under: Other Projects
965. Homemade singing ATMEGA128 Hello guys, After experimenting with 8 octave tone generator, Now, I'm continuing on
creating a singing ATMEGA128 Let's get started, no more delay.... Step 1: Prepare all the parts needed... Let's prepare the part
we need, 1. ATMEGA128 2. The board itself, I created my…... Listed under: Home Automation Projects
966. Speech Synthesis on Atmega128 I had this one project where the device was supposed to speak out the output. And I was
too Lazy to actually go and build a PC based application and not that lazy to make it on a micro controller. So here is some
of…... Listed under: Other Projects, Sound - Audio Projects
967. Standalone Atmega328 We all have a deep fondness to our Arduino with its familiar shades of blue/green, but the time has
come to explore other project options. One that involve fewer pieces, fewer parts, and fewer dollars. Building a standalone
Atmega328 is far simpler than you might…... Listed under: Other Projects
968. The Bat Hat Using Atmega1284 Introduction "An ultrasonic range-finding hat with variable haptic feedback for obstacle
detection." -Project Sound Bite For our ECE 4760 final project, we designed and implemented an ultrasonic range-finding hat
that uses haptic feedback to alert its wearer about obstacles in his or her path. The…... Listed under: Sensor - Transducer -
Detector Projects
969. Ultrasonic Pathfinder Using Atmega1284 Introduction: Our final project for the ECE 4760 course consists of a wearable device to provide aid for the
visually impaired. An ultrasonic distance sensor located on a hat collects data of the surrounding environment scanning the area ahead of the user,
and uses this…... Listed under: Sensor - Transducer - Detector Projects

970. Acoustic Wayfinder Using Atmega1284 Our acoustic wayfinding device utilizes ultrasonic range finders and haptic feedback
to facilitate indoor navigation for the visually impaired. The technique of acoustic wayfinding uses auditory cues, such as
sounds from the natural environment or sounds created artificially, to determine an individual's surrounding physical
space…... Listed under: Sensor - Transducer - Detector Projects
971. Clap-E acoustic tracking robot using atmega1284 An Introduction For the ECE 4760 final project, we designed and built a
sound follower robot named Clap-E. As its name implies, Clap-E receives a clap sound and moves toward the source of
clapping. It has the ability to change its position after multiple claps…... Listed under: Robotics - Automation Projects
972. Acoustic Impulse Marker Using Atmega1284 Introduction "A device that tracks sound impluses with a three microphone
array" We designed and build a 2-dimentional Acoustic Impulse Marker system which is capable of detecting a sharp sound
anywhere in its vicinity and precisely marking its source vector with a servo based pointer.…... Listed under: Sensor -
973. Rock-Paper-Scissors-Spock-Lizard Game Using Atmega1284 Introduction This project implements rock-paper-scissors game
that displays on the TV screen using camera to capture human gesture and doing image processing. Rock-paper-scissors-
spock-lizard game is very popular among teenagers. Our idea comes from a very popular American comedy: Big Bang! In this
TV show we…... Listed under: Game - Entertainment Projects
974. Automobile parking simulator Using Atmega1284 1. Introduction The game consists of two levels. In each level, a LCD TV
screen displays the 2-D top view of the a parking lot, and the player needs to park the car into the proper parking spot by
operating on a fake steering wheel,…... Listed under: Car Projects, Game - Entertainment Projects
975. Infrared Theremin Using Atmega1284 Introduction A modern-day twist on the classic theremin musical instrument. This
project uses two IR sensors and the ATMEGA1284P microcontroller to create an inexepensive, easy-to-use theremin. The
theremin is a musical instrument which is controlled by the electromagnetic field your body body produces naturally. One…...
976. GPS Running Watch Using Atmega1284 Runners who have moved to a new city may get lost trying to remember the route
they carefully planned at home. Instead of stopping the run to pull out a phone, wait for the map to load, find where you are,
and determine where you…... Listed under: GPS Based Projects
977. DJ Party: A Collaborative Music Teacher using Atmega1284 Introduction "This device allows friends to learn songs, create
their own songs, and collaboratively merge them." Our final project for ECE 4760 is a fully customizable button keyboard that
has a variety of features to allow for collaborative music-making between friends. Each keyboard has eight…... Listed under:
Sound - Audio Projects
978. Wireless Pedometer Using Atmega1284 Introduction There’s a simple question asked by runners, walkers, joggers, and anyone who moves. How fast
am I going? Runners want to pace themselves, athletes are trying to train for events, and even on a day to day basis you might wonder how far you…...
Listed under: Radio Projects

979. Stabilized Gimbal System Using Atmega1284 This webpage describes the development of a Stabilized Gimbal Control System
for the CUAir team, Cornell University's Unmanned Air Systems Team. The Stabilized Gimbal Control System will help the
CUAir team compete at the Association for Unmanned Vehicle System International (AUVSI) Student Unmanned Air
Systems…... Listed under: Security - Safety Projects, Sensor - Transducer - Detector Projects
980. Laser Tag with wireless logging using Atmega644 Introduction "A new spin on Laser Tag with Wireless Real-Time Updates"
For our ECE 4760 final project, we designed and built our own laser tag system. We included many traditional laser tag
features, but then added our own 4760 twist. For the purposes of a…... Listed under: Other Projects
981. Gesture Based Security Lock Using Atmega1284 Introduction Our final project is to design a security system which can be
unlocked by means of a stored gesture pattern. The idea is to create a box like assembly, in which the user places his hand,
makes a defined gesture and unlocks the system.…... Listed under: Security - Safety Projects
982. Pushup Trainer Using Atmega1284 For our ECE 4760 final project, we choose to develop an electronic push-up trainer that
could monitor people's movement, provide training package to optimize their push-up exercise and body health. A distance
meter will be used to figure out whether the posture of the person…... Listed under: Medical - Health based Projects, Sensor -
983. ColdRunner – A Temperature Feedback Running Band Using Atmega1284 For our ECE 4760 final project, we designed and
built a running band that provides feedback to users with temperature and vibration. This provides an unique way to monitor
running habits with temperature feedback. The running band attaches to a user's upper arm and counts…... Listed under:
984. Servo-Controlled Fire Extinguisher Using Atmega1284 Introduction We have created an autonomous, servo-controlled fire
extinguisher that is capable of aiming photo sensors and a water nozzle along two axes to detect and extinguish candle fires
a short distance (about 1 ft.) away using a small burst of water. Our inspiration originally…... Listed under: Sensor - Transducer
- Detector Projects
985. The Webcam Mouse Using Atmega1284 For our ECE 4760 final project, we designed and built a pointing device with
webcam-color-tracking based movement control. Our implementation allows the user to wear a set of finger-sleeves
complete with buttons for clicking and scrolling and a red LED for color-tracking cursor control to…... Listed under: How To -
DIY - Projects
986. Automated Drink Mixer Using Atmega1284 Abstract The automated drink mixer takes orders from a push-button menu, and
moves a regular 16-ounce glass under a series of inverted bottles while dispensing specified amounts of mixers to make
perfect non-alcoholic beverages. Introduction If you’ve ever been to a crowded bar or…... Listed under: Home
Automation Projects
987. A Touchscreen Chinese Chess App Using Atmega1284 With the increasing popularity of smartphones and tablet computers, touchscreen has become
one of the most common user interfaces encountered today. The idea of this project came from some apps on the smart phone. It is very interesting
to play a virtual Chinese chess on…... Listed under: Game - Entertainment Projects

988. Beacon: A Zero Instruction Navigation Device Using atmega1284 Introduction to the Device Beac0n allows us to explore the
tacit human understanding of technological feedback. The Beac0n is a gps pathfinder that is designed to be completely
intuitive to the user. The goal is for the user to pick up the device, and with…... Listed under: GPS Based Projects
989. Acoustic Modem Using Atmega1284p Data transmission over sound is used in many communication protocols, the most
common being Dual-Tone Multi-Frequency signaling (DTMF). It is used to dial phone numbers and the frequency
combinations chosen for the digits are very familiar to the general public. It was also used in…... Listed under: Sound - Audio
Projects
990. A Moving Alarm Clock Using Atmega1284 Introduction We implemented a prototype for a moving alarm clock which runs
away from the user when they try to silence the alarm. It has all the features of a “regular” alarm clock: settable time and
alarm, snooze, and alarm on/off. The alarm clock displays…... Listed under: Clock Projects
991. Precision Cooker: A Temperature Controlled Cooker Using Atmega1284 Precise time and temperature control are critical
when cooking. Slight deviations in either temperature or cooking time can ruin delicate ingredients. Despite this fact, most
modern day stovetops provide no data regarding their current temperatures and do not have built in timers. The stovetops
that…... Listed under: Home Automation Projects
992. Eye Mouse Using Atmega1284 Our final project moves and clicks a mouse cursor on a computer screen by tracking where
the user's eye-movements using infrared eye-tracking technology and a gyroscope. The motivation for this project came
from thinking about applications of infrared technology. We narrowed our ideas down to…... Listed under: Sensor -
993. Scan-E: An optical blood pressure sensor Using Atmega1284 Introduction For this project, we created a noninvasive heart
rate and blood pressure measurement tool with the intention of gathering data for large-scale analysis for the automatic
prediction of heart disease. In modern society, patients often have access to a wealth of electronic data concerning…... Listed
994. Low-Budget Laser Projector Using Atmega1284 Introduction For our ECE 4760 final project, we designed a low-budget laser
projector system. The project was broken into main sections: the custom hardware designed and fabricated to make up the
projector, the circuitry controlling the hardware, and the custom software controlling the circuitry. We…... Listed under: CNC -
995. Autonomous Air-Hockey Goalie Using atmega 1284 This project is intended to perform the role of a goal-keeper in the
popular arcade game Air Hockey. In this project, the robot shown below senses a puck coming toward it and moves in the
direction of the puck's motion so as to stop it.…... Listed under: Game - Entertainment Projects, Home Automation Projects
996. NFC Transmitter and Receiver Using Atmega1284 Introduction Our project is building one set of NFC module including a NFC
transmitter and a NFC receiver both using ATmega1284p microcontroller. We will be using coupled coils to transmit message
modulated by a high frequency carrier, whose frequency is the standard frequency for Near…... Listed under: Interfacing(USB
- RS232 - I2c -ISP) Projects
997. Remote Controlled POV Display Using Atmega1284 Introduction For our ECE 4760 final project, we designed and
implemented a remote controlled persistence-of-vision (POV) display that is able to display multiple patterns based on
remote input. The primary components of the display are a rotor and a motor. The rotor is mainly consisted…... Listed under:
LED Projects, Sensor - Transducer - Detector Projects
998. POV Magic 8 Ball Using Atmega1284 1.Introduction In our final project of ECE 4760, we designed a magic 8 ball, which is a rotating POV (persistence
of vision) display controlled by voice commands. In our design, users can ask yes/no based questions via a small speaker, and the rotating POV

part…... Listed under: Game - Entertainment Projects
999. The Air Mouse Using Atmega1284 Introduction "A wireless mouse unit that requires no flat surface by using ultrasonic
positioning." For our ECE 4760 final project,we have designed a surface-less mouse interface using ultrasonic transmission as
our final project in this class. The idea is to have a ultrasonic transmitter as…... Listed under: Interfacing(USB - RS232 - I2c -
ISP) Projects
1000. EEG Magic Cat Ears Using Atmega1284 Kang Li(kl694) and Zhenxuan Qiu(zq39) For our ECE 4760 final projec, we built a pair
of toy “cat ears” using electroencephalography (EEG) with the AVR microcontroller. The basic function of it is that it can
change the gesture of the “Ears” based on the participant’s…... Listed under: Game - Entertainment Projects
1001. Drumming Teaching and feedback device Using Atmega1284 For our ECE 4760 final project, we designed and built a drum
trainer that can be attached to most Japanese drum surface and will detect and wirelessly transmit different drum hit types to
other players’ drum trainers. The trainer is able to determine whether the…... Listed under: Sound - Audio Projects
1002. Thermistor Respiratory Monitor Using Atmega1284 Our final project for ECE 4760 is a respiratory monitor that was designed
for low-resource environments. The device calculates a patient's breathing rate by detecting changes in temperature when
the patient breathes through a mask. Features of the device include an alarm through a piezoelectric…... Listed under:
1003. Glove Mouse Using Atmega1284 For our ECE 4760 final project, we designed and built a wireless computer pointing device
with accelerometer based movement control. Our implementation allows the user to wear a set of hardware (a glove and
connected armband) and control a cursor through different hand orientations and…... Listed under: Sensor - Transducer -
Detector Projects
1004. Hand-Motion Chess Using Atmega1284 An Introduction "A glove embedded with accelerometers to play a hand motion-
controlled chess game" project soundbyte For our ECE 4760 final project, our team designed and built a system with the
ability to play the game of chess using embedded gloves. Each player wears a…... Listed under: Sensor - Transducer - Detector
Projects
1005. Color to Sound Player Using Atmega1284 Introduction We created a device that determines the RGB content of a surface and
then speaks the color or plays a musical tone at the sound frequency mapped to the color. The device can convert the color
to sound directly or function as a cassette…... Listed under: Sound - Audio Projects
1006. Multi-functional Music Box Using Atmega1284 Our final project is to build a multifunctional music box. This music box can
generate different songs in different instrument sounds, i.e. piano, organ, by FM synthesis. The theme and harmony are in
two different channels. Besides, the music box can also be electrical piano…... Listed under: Sound - Audio Projects
1007. Muscle music control Using Atmega1284p Introduction For our ECE 4760 Final Project, we use an infrared LED and
phototransistor armband to detect muscle inflections in arm and wrist movement which are used to manipulate the volume
and speed of pre recorded songs. By pumping your fist, you will change the…... Listed under: Sound - Audio Projects
1008. Digital Reversi board using Atmega644 Introduction For our final project in ECE 4760, we designed and implemented a
Reversi board consisting of hardware, a microcontroller, and a touch screen. Sixty-four bicolor (red and green) LEDs were
implemented as the black and white pieces of the game. Players could simply light…... Listed under: Development Board - Kits
Projects
1009. Audio Spectrum Analyzer Using Atmega644 Our ECE 4760 final project was an audio spectrum analyzer that would display a
histogram-style visualization of an audio signal. We were able to successfully display the frequency spectrum content of an
audio signal in real-time using a black and white histogram visualization with bins…... Listed under: Sound - Audio Projects

1010. Optical microphone and spectrum analyzer Using Atmega1284 We implemented an optical microphone which converts
distant vibrations, including sound, to an audio signal. Measuring the reflection of a laser beam from windows or glass, it
possible to hear sounds near the target. The system also includes frequency spectrum analysis with a real-time display…...
Listed under: Radio Projects, Sound - Audio Projects
1011. IFF System for Infantry Using Atmega1284 Introduction "An encrypted laser-based friend-foe identification system to prevent
friendly fire in battle" This project implements an Identification Friend-or-Foe (IFF) system for use by soldiers to prevent
friendly-fire. The inspiration for the project is derived from Identification Friend-or-Foe (IFF) transponder systems currently
used on fighter…... Listed under: Sensor - Transducer - Detector Projects
1012. Persistance of Vision Clock Using Atmega644 The goal of our project was to create a persistence-of-vision (POV) analog clock
using an LED display. The clock has a visual alarm system which lights up the entire display for two seconds if it reaches an
alarm time. The current time and alarm times…... Listed under: Clock Projects
1013. Virtuoso: A Touchscreen Music App Using Atmega644 n our final project, we designed an electronic multifunction instrument
with a LCD touch screen and a microphone. The user can play three kinds of instruments on it -- xylophone, flute and piano.
Each instrument has a different interface and timbre. The piano part has…... Listed under: Sound - Audio Projects
1014. NFC Secure Data Storage Using Atmega644 Summary "Enabling secure storage capabilities for sensitive data through
standardized methods of encryption or multiple agent distribution." Our group chose to implement a secure form of storage
for sensitive information such as passwords or identification numbers. This is modeled after Shamirs secret sharing algorithm.
It…... Listed under: RFID - NFC Projects
1015. Ultrasound Gesture Detection Using Atmega644 Introduction In this project, ultrasound around 24kHz was used to detect
movement near an object. Waving a hand or other solid object near the source of the ultrasound (speaker) causes a shift in
the frequency of the sound, which is then detected by a microphone.…... Listed under: Sensor - Transducer - Detector Projects
1016. Wireless, voice-controllable, household system Using Atmega644 Motivation We design a smart home control system which
allow people control their home devices by voice command at home. This is a wireless, voice control system. People could
control almost all the facilities at home including lights, fans or even back ground music. Right…... Listed under: Sound -
Audio Projects
1017. Solar Powered Pulse Oximeter and Heart Rate Meter Using Atmega644 Introduction Pulse Oximeter is a non-invasive medical
diagnostic device used to detect the oxygen saturation of the blood. Heart rate meter detects the number of beats per
minute of the patient, normally referred to as bpm. The pulse oximeter is designed using an infrared and…... Listed under:
1018. RoboSLR Using Atmega644 Introduction Robo-SLR provides a remotely controllable stand for a Canon EOS 550D DSLR
camera, allowing for adjustable tilt and pan functionality along with the ability to remotely view through the camera's
viewfinder and take photos. An ATmega1284 microcontroller is used to control camera functions as…... Listed under: Robotics
- Automation Projects
1019. Radio Station Tracker Using Atmega644 Our project is inspired by the commercial product, PicoDopp, which uses a similar
scheme for foxhunting. Foxhunting is a contest where participants try to locate a transmitter, called the fox, simply by
monitoring the signals it transmits. Typically this is done using highly directional antennas…... Listed under: Radio Projects,
1020. OBD-II Autocross/Track Data Logger for BMW E36 M3 Using Atmega644 Customer's Voice “Hello, I am interested in a race car logger than will be able
to display and log crucial information during autocross and track events. I am interested in tracking vehicle speed, RPM, engine coolant temperature

and lateral g-forces. Ideally, the data can be…... Listed under: Car Projects
1021. Brain-Computer Interface Using Atmega644 Introduction Our goal was to build a brain-computer interface using an AVR
microcontroller. We decided that the least invasive way of measuring brain waves would be using electroencephalography
(EEG) to record microvolt-range potential differences across locations on the user's scalp. In order to accomplish this,…...
1022. Digital Saxophone Using Atmega644 Abstract My final project was the design of a digital saxophone which can reproduce
the sound of an actual saxophone through digitally synthesized electrical waveforms. The digital saxophone consists of a
microphone to sense the user blowing into a mouthpiece, push-buttons to control the note…... Listed under: Phone Projects
1023. Virtual Saxophone Using Atmega644 Our ECE 4760 final project was to create a virtual saxophone that uses Direct Digitial
Synthesis (DDS) to synthesize the output notes. Pushbuttons are connected to a PVC pipe to mimic the saxophone's
mechanical structure, and a microphone that detects noise is used to determine…... Listed under: Phone Projects, Sensor -
1024. Auto-composing keyboard Using Atmega644 Project Overview We designed an electric piano that automatically composes a
piece of music for the ECE 4760 final project. All the user need to do is to select a mood of the music and play two notes
upon which the music is based, and…... Listed under: Development Board - Kits Projects, Sound - Audio Projects
1025. MicroKart 644 Using Atmega644 The Micro Kart 644 is a mobile device that provides additional capability to the traditional
RC car experience. Allowable functions are recording multiple tracks, which consist of all user controls sent to the car over a
25 second interval, and replaying the tracks so the…... Listed under: Car Projects
1026. Touchpad Figure Recognition Using Atmega644 Our project implements a touchpad input system which takes user input and
converts it to a printed character. Currently, the device only recognizes the 26 letters of the alphabet, but our training system
could be easily generalized to include any figure of completely arbitrary shape,…... Listed under: Development Board - Kits
Projects, LED Projects, Sensor - Transducer - Detector Projects
1027. Battle video game Using Atmega644 Introduction Our project is a simple game where two players control tanks in a stage
with the ultimate goal of destroying each other. User input is achieved through the use of keypads, which are used to both
control the tanks and fire missiles at one…... Listed under: Game - Entertainment Projects
1028. Sign language translator Using Atmega644 Introduction "A portable Glove Based Sign Language Translator with LCD Display,
Speech Synthesis, and Sign Language Education Software" Sign language is a language through which communication is
possible without the means of acoustic sounds. Instead, sign language relies on sign patterns, i.e., body language,
orientation…... Listed under: Sensor - Transducer - Detector Projects
1029. Evolutionary Altitude Control for a Helicopter Using Atmega644 Overview For our ECE 4760 project, we developed a self
learning 1 degree of freedom (DOF) helicopter using a neural network learning algorithm and infrared (IR) distance
measurement. The primary goal is to increase the helicopter height to a desired level in the quickest amount…... Listed under:
1030. Digital Stethoscope Using Atmega644 "A digital stethoscope that can amplify, play, and record heart signals in real-time."
Project Soundbyte The purpose of this project was to design and implement a digital stethoscope to serve as a platform for
potential computer aided diagnosis (CAD) applications for the detection of cardiac…... Listed under: Medical - Health based
Projects
1031. Power Manager: Remote Power Control Through LAN using Atmega644 Introduction Overview PowerManager is a remote power management system
that can be controlled through a web browser on a local area network (LAN). Devices plugged into PowerManager's outlets can be turned on or off
with the click of a button on a webpage. PowerManager runs…... Listed under: Internet - Ethernet - LAN Projects

1032. Heliowatcher solar tracker Using Atmega644 Documentation HelioWatcher: Automatic Solar Panel Control Jason Wright
(jpw97) and Jeremy Blum (jeb373) Introduction We designed and built a system to automatically orient a solar panel for
maximum efficiency, record data, and safely charge batteries. Using a GPS module and magnetometer, the HelioWatcher
allows the…... Listed under: Sensor - Transducer - Detector Projects
1033. Cooking Assistant for Automatic Temperature Control Using Atmega644 In some cooking scenarios, it is desirable to achieve
a specific object temperature and keep the object at that temperature. However, it is difficult to maintain a constant
temperature without constant attention. To aid cooking in this scenario, we created a device that can be…... Listed under:
1034. SousVide immersion cooker using Atmega644 About What is this thing? For our ECE4760 Spring 2012 (Microcontrollers) Final
Project at Cornell University we decided to create a sous-vide cooker (a type of immersion cooker) that can maintain a set
temperature for extended periods of time. It can auto-calculate the appropriate time…... Listed under: Home Automation
Projects
1035. BrainMap: fNIR imaging of the brain Using Atmega644 Introduction Our project records and extracts event-related features
from a 36-point relative blood-oxygen concentration sensor array from the surface of the brain. We chose this project
because of a combined interest in brain-computer interfaces. In an attempt to balance cost, complexity, and sensor density,
we…... Listed under: How To - DIY - Projects, LED Projects
1036. MAD-DOG Kick-Awesome Wi-Fi Audio Streamer Using Atmega644 Introduction "We developed a wireless receiver capable of
receiving and playing audio transmitted over an 802.11 Wi-Fi network" project soundbyte For our ECE 4760 final project we
developed a wireless receiver capable of receiving and playing audio transmitted over an 802.11 Wi-Fi network. Our
system…... Listed under: Radio Projects
1037. Remote Controlled DMM With Minimum Mass Wireless Coupler Using Atmega644 Introduction In this project, we built a
digital multi-meter utilizing near-field communication concept. The system established a bidirectional wireless
communication between the measurement unit and the base unit. The measurement unit is in charge of measurement and
transmitting the result to the base, while the…... Listed under: Sensor - Transducer - Detector Projects
1038. Seven day alarm Using Atmega644 Introduction The variability of a college student’s class and school work schedule gives
way to an abnormal sleep/wake pattern that is not experienced any other age group. Few lucky students have the pleasure of
having all their classes start at the same time every day.…... Listed under: Clock Projects
1039. A Budget Pachinko Machine Using Atmega644 Pachinko is a game in which a ball drops down through a large quantity of
pegs and the objective is to catch that ball in a fixed basket. The concept behind our machine is novel in that it was built
using mostly discarded and salvaged…... Listed under: Game - Entertainment Projects
1040. Quadcopter Using Atmega644 Introduction Many embedded systems use sensors that combine an accelerometer and a gyroscope. Quadcopter is
one of the examples of that. Already-built cheap toy-like quadcopters are available on e-bay around at $25~$30, but many hobbyists and avid AVR
programmers build their own quadcopters. We thought…... Listed under: Game - Entertainment Projects

1041. Ultrasonic Security System Using Atmega644 Introduction We were inspired to build an ultrasonic security system for our
final project by our housing situation this summer. Security is an important part of home. Especially if we are going to share a
house with prior strangers without a lock on our room…... Listed under: Security - Safety Projects
1042. Smart Trash system Using Atmega644 Introduction top For our final project, we have designed and built a 'proof of concept'
prototype for Project Green Stations, an externally funded student group with the following mission statement: Project Green
Stations is all about changing the way people see the environment. Imagine the…... Listed under: Other Projects
1043. GPS Tracking Device for Cornell Engineering Quad Using Atmega644 Introduction "A GPS tracking devices capable of telling
the user his/her approximate distance to buildings and attractions on a map downloaded from a remote station" -Project
Soundbyte For our final project in ECE4760, we designed an GPS tracking device that has a capability of downloading…...
Listed under: GPS Based Projects
1044. Autonomous Board Erasing Robot Using Atmega644 Abstract -A Roomba for boards For our ECE 4760 final project we
created a board climbing robot capable of cleaning the board autonomously. The robot uses neodymium magnets to stick to
the board and moves across it with two continuous servo motors. It has bumper…... Listed under: Robotics - Automation
Projects
1045. Self-Reliant Power and Data Management System Using Atmega644 Introduction The tags used to monitor wildlife can either
be passive or active. Passive tags simply identify an individual, whereas active tags may send out a radio beacon or even
collect data. These active tags, more commonly referred to as “bio-loggers”, are typically battery powered,…... Listed under:
1046. A Wireless Programmable Pace Clock Using Atmega644 For our ECE 4760 final project, we designed and built a wirelessly
programmable digital pace clock with a large format LED display and Android smartphone control and programming. This
original design achieves the functionality of commercailly available pace clocks but with an intuitive user interface…... Listed
under: Clock Projects
1047. Rock Band Vocal Bot Using Atmega644 We have created a device that interprets the NTSC video signal from the video game
Rock Band and outputs audio signals via a pair of speakers to simulate a human singer playing the vocalist part. We chose to
pursue this project since we were interested…... Listed under: Game - Entertainment Projects
1048. DJ Multitouch — A FTIR Touchscreen Device Using Atmega644 Overview The DJ Touch is a portable turntable touchscreen
and interactive LED display. Our end goal was to produce a low cost touchscreen device, and demonstrate its application in a
common consumer application. Out of an interest in electronic music, and with the knowledge of…... Listed under: LCD
Projects
1049. FaceAccess — A Portable Face Recognition System Using Atmega644 We created a standalone face recognition system for
access control. Users enroll in the system with the push of a button and can then log in with a different button. Face
recognition uses an eigenface method. Initial testing indicates an 88% successful login rate with…... Listed under: Sensor -
1050. Voice decoder for vowels Using Atmega644 Introduction In our final project, we created a smart voice decoder system that is
capable of recognizing vowels in human speech. The audio input is sampled through a microphone/amplifier circuit and
analyzed in real time using the Mega644 MCU. The user can record and analyze…... Listed under: Other Projects
1051. Ahhhh…BIU! video game Using Atmega1284 Introduction EVERYONE LOVES GAMES! In this project, I built a video game controlled by people’s voice.
The game is about jet fighters. People can play the game by themselves or with friends. The system recognize the command by distinguish “ahh” and

“Biu”. The fighters shoot…... Listed under: Game - Entertainment Projects
1052. Wireless, web-based, cardiac monitor Using Atmega644 Introduction "A composite personal health monitor solution bridges
the gaps between patients and doctors." ---Engineering Goodwill This project creates a portable device implementing
wireless technology and taking full advantage of the wide-spreading Internet to provide a convenient solution to monitor
human health. The health information…... Listed under: Other Projects
1053. A Portable, Automated, web-based Bird Trapping Mechanism Using Atmega644 Background We designed and implemented
an automated, portable bird-trapping mechanism, along with an associated system which is scalable Every year between
early May and mid-June large amounts of tree swallows migrate to Ithaca, NY area to mate. The study of these birds
invariably require a…... Listed under: Motor Projects
1054. Autonomous visually steered car Using Atmega644 Introduction For our final project, we re-engineered a remote control car
to autonomously navigate through a track by detecting lanes and centering itself between them as well as detect objects in
front of it and avoid collision. The RC car detects lanes through image input…... Listed under: Car Projects
1055. Step Sequencer Drum Machine Using Atmega644 Overview [top] As avid audiophiles, we wanted to apply our newly acquired
knowledge of microcontrollers to build a fun consumer electronic device. Our project is a step sequencer drum machine. The
user is able to program a 16-step percussion pattern using one of a wide…... Listed under: Other Projects
1056. LED-Following K'NEX Car Using atmega644 Introduction In a Nutshell Our ECE 4760 final project was a car made of K'NEX
that follows a LED strip. What We Did For this project we made a K’NEX car that follows a path made by a LED strip. We used
two phototransistors to…... Listed under: Car Projects, LED Projects
1057. Rock-Paper-Scissors Sensor Gloves Using atmega644 For our ECE4760 final design project, we designed and built a two
player game system for rock-paper-scissors. Our implementation involved the use of two sensor gloves (one for each player)
that tracked bends in the user’s fingers, to determine the symbol put out by each…... Listed under: Game - Entertainment
Projects
1058. Ear Trainer Using Atmega644 Introduction Our project is a self-contained system that helps people develop the musical skills
of perfect pitch and relative pitch. Push buttons allow the user to navigate a graphical user interface (GUI) on a liquid crystal
display (LCD). In perfect pitch training mode, a note…... Listed under: Sensor - Transducer - Detector Projects
1059. TI Calculator Wireless Chat Using Atmega644 INTRODUCTION: Our project is a wireless communication link which interfaces
to the serial ports on the TI-83 and TI-84 calculators. SUMMARY: Our group created a wireless communication system for the
widely popular TI 83/84 calculators. The system interfaces to each calculator through their 2.5mm serial…... Listed under:
Calculator Projects
1060. Sonar SensCap Using Atmega644 SensCap is a device that guides the visually impaired around obstacles. Introduction We
designed and built a device to be worn on the head and around the hip to aid the visually impaired maneuver around
obstacles. It provides information about obstacles near and around the…... Listed under: Sensor - Transducer - Detector
Projects

1061. A Keyboard Synthesizer Workstation using Atmega644 Our Keyboard Synthesizer project aims to create a multi-instrument
keyboard that can record several different synthesized instruments and play back the track simultaneously. We took a
children’s toy keyboard and adapted the printed circuit board within to play a range of notes from various musical…... Listed
under: Sound - Audio Projects
1062. Compact Guitar Pedalboard Using Atmega644 Introduction For our ECE 4760 final project, we designed and built an electric
guitar pedalboard that will take in an analog audio signal from a guitar and add analog effects such as equalization, gain
control, as well as digital effects such as distortion, compression, and…... Listed under: Sound - Audio Projects
1063. Embedded Foot Pronation Detection Using Atmega644 Introduction and Rationale Our ECE 4760 design project integrates
three different kinds of sensor measurements to track a user�s movement speed, regularity of gait, force on impact,
pronation of foot, as well as other information that may be useful to a podiatrist. We believe there…... Listed under: Sensor -
1064. Human Tracking Fan System Using Atmega644 For our final project we decided to construct a human tracking rotating
platform that supports a fan. The platform, using dual element Pyroelectric Infrared Sensors (PIR) sensors, rotates itself
independently to direct air flow to whatever position a person moves to. In addition, the fan…... Listed under: Sensor -
1065. Invisible band Using atmega644 Introduction The goal of this project is designing microcontroller operated drum set and
guitar which are only consist of drums sticks, pedals, and pick. This is done by implementing accelerometers which are
connected to the microcontroller. By swinging the sticks and picking the guitar in…... Listed under: Sound - Audio Projects
1066. Sheet Music Notator Using Atmega644 Introduction We created a system that takes input from a piano and displays the
musical notation for it on a television screen. The system uses hardware amplification and filtering of a microphone output
with code in C compiled on two Atmel Mega644 microcontrollers. The basic…... Listed under: Sound - Audio Projects
1067. ToneMatrix Touch Sequencer Using Atmega644 ToneMatrix Touch by Jane Park, Michael Chin We can be reached at {jp624 |
msc247} at cornell dot edu. ---a touch-based, interactive matrix that plays music corresponding to active grids and displays
playback state using LEDs Introduction The ToneMatrix Touch (TMT, aka Teenage Mutant Turtle)…... Listed under: LED Projects
1068. Automated grapefruit segmenter Using Atmega644 Part I. High Level Design 1 Rationale and Problem Overview As regular
grapefruit consumers, both of us could appreciate the value in automating the cutting procedure. We saw the problem as
suitable for a final project because it is [very] challenging while requiring a combination of…... Listed under: Home
Automation Projects
1069. Motion Sensing PowerPoint Controller Using Atmega644 Introduction For our Final Project in ECE 4760, we built a controller
that interfaces with a computer running a PowerPoint display through USB. The device can control slide transitions based on
hand motions or button presses as well as play MP3 files when it detects…... Listed under: Interfacing(USB - RS232 - I2c -ISP)
Projects
1070. Heat Control System Using Atmega644 Introduction This project was the first stage of developing a controller for a radiant
floor heat system. The microcontroller will use inputs from thermostats, thermocouples, a flow meter, and pressure switches
to control the operation of the pumps and valves to achieve improved efficiency of…... Listed under: Temperature
1071. XBee RF Smart Energy Compliant Power Meter Using Atmega644 Motivation >A breaker-level power metering device for measuring energy on 4
different circuit lines and wirelessly outputting that energy data onto Google PowerMeter. Useful Links Google PowerMeter Smart Energy Alliance
DOE - SmartGrid Energy Efficient Products Similar Projects Zigbee Wireless Relay Control & Power Monitoring…... Listed under: Metering - Instrument
Projects
1072. 3D Paint Using Atmega644 "A 3D canvas on which the artist can draw using trilaterated coordinates from ultrasonic delays." Project Soundbyte For
our final project in ECE 4760, we designed and implemented a three-dimensional paint program consisting of hardware, a microcontroller, and a PC

running MATLAB. All three modules…... Listed under: Home Automation Projects
1073. Hand controller for Parrot AR Drone Quadricopter Using Atmega644 Introduction Our project is a novel hand held controller
in which we use an accelerometer to wirelessly control the motion of a Parrot AR Drone Quadricopter. Rationale: The main
idea of our project was building a cool glove controller for a flying platform, a quadrotor…... Listed under: Robotics -
Automation Projects, Sensor - Transducer - Detector Projects
1074. Human Tetris — Video object tracking Using Atmega644 We have created a real-time video object tracking / shape
recognition device, and a fun game library to demonstrate its abilities. For our project, we wanted to push the video sampling
and processing capabilities of the ATmega644 8-bit microcontroller. Using a high-speed analog-to-digital converter as…...
Listed under: Sensor - Transducer - Detector Projects, Video - Camera - Imaging Projects
1075. Auditory navigator Using Atmega644 Introduction Navigation in the past has primarily relied on the use of a map, compass
or other devices that must be interpreted visually. This project demonstrates the ability to navigate a user based on
synthesized directional audio which allows the user to move to a…... Listed under: GPS Based Projects
1076. USB wireless tilt mouse Using Atmega644 Introduction We created a handheld mouse device that measures its tilt and then
wirelessly transmits the data to a base unit, which is connected to a PC through a USB cable and can be recognized by certain
modern computers as an actual mouse. The purpose…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
1077. Automated Rock Band player Using Atmega644 Introduction For our final design project, we built an automated Rock Band
player that can beat any Rock Band song by decoding the Xbox 360 video output and sending the appropriate button push
and strum signals to a modified Xbox controller. This project was particularly…... Listed under: Sound - Audio Projects
1078. Automated Pavlovian Classical Conditioning of Insects Using Atmega644 Introduction Several studies have shown that
various insects possess learning and memory abilities. One approach researchers use to demonstrate such abilities is to
"teach" the insect to exhibit a specific behavior in response to a stimulus. This "teaching" process is called Pavlovian
conditioning. Such studies…... Listed under: Sensor - Transducer - Detector Projects
1079. CMOS Camera Rock Paper Scissors Game System Using Atmega644 Introduction We created a rock paper scissors game that
utilizes a CMOS camera to determine what hand the human player plays. The player is required to wear a glove that has black
tape taped on each finger. When the player plays the hand, the camera…... Listed under: Game - Entertainment Projects
1080. RFID based Mobile Payment System Using Atmega644 Introduction and Rationale We used our ECE 4760 final project as a
platform to develop a proof of concept for Mivo. Mivo is a low-cost, stripped down mobile payment system. Our prototype
combines Radio Frequency Identification (RFID), Security Pin Authentication and Ethernet Data Transfer to…... Listed under:
RFID - NFC Projects
1081. Talking voltmeter Using Atmega644 The Handy Lab Buddy is a tool every ECE should have. The four features of this tool
include a talking voltmeter, logic probe, voltage averager, and frequency measurer. As a cheap and accurate device that
outputs whatever being measured through speakers, it's one of its…... Listed under: Metering - Instrument Projects
1082. Heart Rate Display LED T-Shirt Using Atmega644 Introduction We have designed and built a LED t-shirt capable of displaying
the heart rate of the wearer via a pulsing LED heart. Largely, our project consists of two components: the plethysmograph
and the LED display. How we came up with the Idea We had…... Listed under: LED Projects, Medical - Health based Projects
1083. Gesture Based Touchpad Security System Using Atmega644 Introduction The purpose of the project is to present a new
approach on the design of security systems by using a touch sensitive device. Security is a permanent concern in a variety of
environments ranging from physical access restriction in home and industrial settings to…... Listed under: Security - Safety
Projects

1084. Flexicopter Using Atmega644 Introduction The purpose of our project is to control a toy helicopter using flex sensors
attached to a glove. The flex sensors are intended to replace the remote control that is generally used to fly the helicopter.
Additionally we also created another mode which will…... Listed under: Sensor - Transducer - Detector Projects
1085. Acoustic Data Modem Using Atmega644 Introduction For our final design project, we designed and built a prototype
acoustic modem to serve as a physical transport layer for digital communications. It converts between a digital
communications scheme (RS-232) and an acoustically coupled communications scheme of our own design. Our project
consists…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects, Other Projects
1086. Adaptive Alarm Clock Using Atmega644 Introduction Elevator Pitch / 1-second Description An adaptive alarm clock that
chooses the optimal time to wake up the user using an accelerometer that detects his/her body movements. Goals The goal
of our final project was to create an alarm clock that is able to…... Listed under: Clock Projects
1087. Zigbee Wireless Relay Control and Power Monitoring System Using Atmega644 Introduction We designed a system for
wirelessly controlling relays and monitoring current. This is used for a home load simulation. By wirelessly turning relays on
and off by sending commands from a PC to a microcontroller we can change the total load (current) to our…... Listed under:
Metering - Instrument Projects
1088. Low-Cost Portable Potentiostat for Biosensing Applications Using Atmega644 Introduction This project involves the design
and construction of a low-cost portable potentiostat capable of performing cyclic voltammetry on three-electrode
electrochemical systems. A potentiostat is an instrument used in chemical and biological tests that controls the voltage
between two electrodes, working and reference, at a…... Listed under: Other Projects
1089. Point of Sale Terminal Using Atmega644 Introduction Point of Sale systems typically can cost up to thousands of dollars we
do it very simply for seventy. For small stores, point of sale systems can be very expensive. One thousand dollars for a piece
of machinery whose functionality is quintessentially simple can…... Listed under: Development Board - Kits Projects
1090. FM Radio Receiver Using Atmega644 Introduction The goal of our project was to design a low cost and user-friendly FM
radio receiver. Our project uses a FM receiver integrated circuit to perform the pre-processing units that are needed before
the desired audio signals can be heard. The radio frequency is…... Listed under: Radio Projects
1091. Mister Gloves – A Wireless USB Gesture Input System Using Atmega644 Introduction Mister Gloves is a wireless USB gesture
input system that enables a person to use a computer by performing intuitive hand and finger motions in the air. While
wearing a glove controller on the right hand, the user can move the cursor by forming…... Listed under: Robotics -
Automation Projects
1092. Accelerometer Based Hand Action Recognition using Atmega644 Introduction We created a wearable game controller that
uses accelerometers to acquire action of the hand and then maps an action to an arbitrary keystroke. The types of actions we
are trying to recognize should be suitable as input control for video games. We placed…... Listed under: Robotics -
Automation Projects, Sensor - Transducer - Detector Projects
1093. Home energy managment Using Atmega644a Introduction Our project implements a smart algorithm in order to power a
house with a photovoltaic, batteries or the power grid. For this project, we worked closely with a research team whose goal
is to power a home with minimal power from the power grid. …... Listed under: Home Automation Projects
1094. Self-Adaptive Hybrid Electro-Magnetic Levitation and Active Balancing System Using Atmega644 Introduction In short, our
project is just an isolated floating plate. Just as our title explained, it is mainly a floating plate that is segregated from all
outside vibration using electromagnetic force. This purpose of the project is to design a system that complements
common…... Listed under: Metering - Instrument Projects
1095. Digital Oscilloscope Using Atmega644 Introduction The goal of our project is to design a digital oscilloscope with 20 kHz bandwidth. The scopes that
we use in ECE 4760 lab cost over one thousand dollars. The motivation of our project is to produce an affordable, easy to make oscilloscope for…...
Listed under: Metering - Instrument Projects

1096. Optical eye tracking Using Atmega644 Introduction We have endeavored to develop a means by which eye gaze can be
detected. This goal was achieved using the same principles learned in Lab4, where we recorded the motor speed of a small
hub fan using the combination of IR emitter plus phototransistor,…... Listed under: Sensor - Transducer - Detector Projects
1097. Guitar Blocks Using Atmega644 Introduction We present to you, the ultimate guitar -- no strings attached (literally)! This
guitar features an infrared strumming system and a fret board with physical buttons. It sounds like a real acoustic guitar and
it works like a real acoustic guitar, but in the…... Listed under: Sound - Audio Projects
1098. Haptic Exercise Coach Using Atmega644 Introduction The goal of this project was to assist the user in learning the proper
technique for a physical exercise, in our case a dumbbell bicep curl. As our understanding of biology and anatomy improves,
the design of physical exercises is improved by the application…... Listed under: Medical - Health based Projects
1099. ATmega644 JTAG Debugger Introduction The purpose of this project was to design and implement a debugger for the
ATmega644 that communicated through its JTAG interface and was capable of controlling program execution by setting
breakpoints and accessing registers and memory. We have three main objectives in this report:…... Listed under:
1100. Ultrasonic Haptic Vision System using Atmega644 Introduction The ultrasonic haptic vision system enables a person to
navigate hallways and around large objects without sight, through the use of an ultrasonic rangefinder that haptically
interfaces with the user via tiny vibrating motors mounted on the users head. The idea behind this project…... Listed under:
1101. Haptic appointment manager Using Atmega644 Introduction The Haptic Appointment Manager manages all of an individuals
appointments, ensuring they arrive on time and in the right location by subtly guiding them throughout the day. This system
uses a GPS receiver and a compass to maintain awareness of its absolute and rotational…... Listed under: GPS Based Projects,
1102. 3D ultrasonic mouse Using Atmega644 Introduction Ultramouse 3D times the delay of high-frequency sound waves from the
unit held by the user to each of three receivers and passes this information along a serial cable to the computer. The
accompanying open-source API provides easy functions that let any Win32/C++ application…... Listed under: Sensor -
1103. 3D scanner Using Atmega644 Introduction This goal of this project is to make an effective, low-cost 3D scanner. Summary
Our project implements the hardware necessary for a laser triangulation 3D scanner as well as a PC user interface for
controlling the scanner and acquiring data via an Ethernet connection.…... Listed under: Interfacing(USB - RS232 - I2c -ISP)
Projects
1104. Gesture Recognition Based on Scratch Inputs Using Atmega644 Contents Introduction High Level Design Program/Hardware
Design Results of the Design Conclusions Appendix A: Commented Code Gesture Recognition Code PC Interface Code
Appendix B: Schematics Appendix C: Cost Details Appendix D: Tasks Appendix E: Gestures References Introduction Our
project utilizes a microphone placed in a…... Listed under: Phone Projects
1105. LED Sensor Piano Keyboard Using atmega644 Introduction Our project utilizes an array of LEDs that work as light sensors to
generate a musical tone, simulating a piano keyboard. The basic idea is to use LEDs as both emitters and sensors. For our
project specifically, we used a total of 63 LEDs,…... Listed under: Development Board - Kits Projects, LED Projects, Sensor -

1106. Touchpad/Infrared Music Synthesizer Using Atmega644 Touchpad/Infrared Music Synthesizer "Generate music with your
laptop touchpad!" Wei-jiunn (Vic) Jang Kalina Jordanova The Touchpad Infrared Music Synthesizer uses a laptop touchpad
and an infrared distance sensor to control tone, volume and decay length of musical notes. Operating in one of six modes,
this…... Listed under: Sound - Audio Projects
1107. Der Kapellmeister Using Atmega644 Introduction This project is implemented with a glove, resembling a conducting baton
that analyzes gestures and interprets them into musical elements. Der Kapellmeister is a simple tool that tests a user's ability
in basic conducting, using a real conducting baton. As a user performs a…... Listed under: Robotics - Automation Projects,
1108. IR harp using Atmega644 INTRODUCTION Wouldnt it be cool to be this guy? Powerful laser shining into the audience,
playing strings by sweeping your hands across the beams, rocking out in a room full of fog and fawning girls? We thought
so. It turns out lasers are expensive, fog…... Listed under: LED Projects
1109. Digital Receipts System Using Atmega644 Introduction Our final project is a conceptual prototype of a digital receipt system.
The basic idea is when making a purchase with a credit or ATM card, the transaction information is automatically packaged
and sent to a webserver where it can be logged in a…... Listed under: Other Projects
1110. ODB-II Automotive data interface using Atmega644 Our goal for this project was to build an OBD-II compliant device that
would communicate with any OBD-II enabled car and read back real time data as well as perform basic performance testing
and diagnostics. If you've ever had to take your car into the…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
1111. Traction control system Using Atmega644 Introduction For our ECE 4760 Final project we have developed a traction control
system that detects wheel slip and adjusts the velocity of the wheels accordingly. Robotic vehicles are becoming increasingly
complex and often need high levels of movement control. Specifically, when the wheels of…... Listed under: Sensor -
1112. ACL Research: Foot Acceleration Sensor Atmega324p Introduction This project was designed to aid a research study by
Cornell Professors Bob Nafis and Yingxin Gao on the reasons behind the higher rate of ACL injuries suffered by female
athletes. This injury rate can be up to three to eight times higher than…... Listed under: Sensor - Transducer - Detector
Projects
1113. Fart Intensity Detector Using Atmega644 INTRODUCTION Our project is a fart intensity detector which ranks fart magnitude
on a scale from 0-9 according to sound, temperature, and gas concentrations. The inspiration for this project was to
determine who could generate the worst flatulence measurable in a personally unbiased manner. To…... Listed under: Sensor -
1114. Dual-Channel Mobile Surface Electromyograph Using Atmega644 Introduction For our final project, we built a surface
electromyograph to collect and analyze data on muscle activity, which supports two channels, implements wireless
transmission, and can be worn as mobile unit. Surface electromyography (EMG) is a noninvasive technique to record the
activation signals of…... Listed under: Phone Projects
1115. Tissue Impedance Digital Biopsy Using Atmega644 Introduction Our project measures and analyzes the electromechanical
properties of tissue using a probe containing a microarray of electrodes, to aid as a tool in predicting the health of the tissue
sample. “Despite significant efforts to develop early detection strategies for breast cancer, the diagnostic…... Listed under:
1116. GPS Data Logger with Wireless Trigger Using Atmega644 Introduction The goal of this project was to create a portable GPS logger that could be
wireless triggered by an external device, such as a camera. Our device that we have designed operates in two modes. The first works as a basic GPS
logger, which…... Listed under: GPS Based Projects

1117. Self-Adjusting Window Shade Using Atmega644 Introduction The self adjusting window shade will automatically raise, lower,
open, and close your blinds by itself. A computer terminal acts as a remote to broadcast instructions to the window shade via
RF. These manual adjustments are stored into the microcontrollers system along with the…... Listed under: Home Automation
Projects
1118. Weather Canvas Using Atmega644 Introduction The Weather Canvas is a robust outdoor weather monitoring system coupled
with an indoor LED display. The outdoor system consists of a microcontroller, temperature sensor, humidity sensor, home-
made anemometer, a Hot Wheels radar gun modified to measure precipitation, and a solar panel to measure…... Listed under:
LED Projects
1119. Autonomous Self-parking car Using Atmega644 Introduction We created an RC Car that can identify a parking space and
parallel park by itself. The RC Car drives down a street searching for a parking space to its right using a distance sensor.
When the car has identified a space, the car…... Listed under: Car Projects
1120. The Autonomous Tennis Ball Picker Using Atmega644 Introduction and Motivation In the tennis and sports equipment
market, there are very few advanced electronic devices assisting in the feeding and picking of tennis balls or any other kind
of balls. Tennis players do not prefer picking up over five hundred balls after a…... Listed under: Sensor - Transducer -
Detector Projects
1121. BalanceBot Using Atmega644 Introduction The BalanceBot is a singular axis self balancing robot that is capable of adjusting
itself to changes in weight and position. We developed the Balance Bot (BB or B2) from a single servo and a single
accelerometer. This was very much a proof of…... Listed under: Motor Projects
1122. Multiple PID motor controller (with Wiimote!) using Atmega644 Introduction The main idea for our project was to implement
an inexpensive solution to the current CU Snake Arm motor-driving system by using a Mega644 microcontroller instead of
multiple 3-Amp motor controllers as the snake arm was originally intended to be driven. Since we used…... Listed under:
1123. Wireless Persistence of Vision Device with Realtime Control Using Atmega644 Introduction We set out to make an easy to
interact with, highly custimizable POV display. In deciding on a project we looked for a challenge that would have a good mix
of hardware and software problems. We ended up primarily concentrating on looking at unusual…... Listed under:
Microcontroller Programmer Projects, Radio Projects
1124. Programmable RGB Spinning LED Display Using Atmega32 Introduction For our final project, we built a mechanism that spun
a linear array of seven LEDs at a velocity that made it appear as if a message was being displayed using persistence of vision
for the human eye. To accomplish this, we first had…... Listed under: LED Projects
1125. Alarm clock with speech synthesis Using Atmega32 1. Introduction We designed an intelligent alarm clock which can be
programmed from the computer to speak custom messages and also detect whether the user is on his bed or leaving his
room. Sensors are pervasive in industrial, aerospace, and medical fields. Although they can…... Listed under: Clock Projects
1126. Blackout game Using Atmega32 1 Introduction Black Out is an electronic puzzle game that is a derivative of Lights Out released by Tiger Toys in
1995 but with a few additional twists. The game consists of a 4 by 4 grid of LEDs with each LED having a…... Listed under: Game - Entertainment
Projects

1127. ESD Foam Touch Controlled Brick Blaster Using Atmega32 Introduction As technological devices become more advanced and
a bigger part of our daily lives, the user interface of devices is becoming more important; intuitive and modern interface
provides a real means of transferring the pure computational power of a device to the user experience.…... Listed under:
1128. NES EMULATION USING ATMEGA32 OVERALL DESIGN GOAL The overall goal of our project was to recreate the Nintendo
Entertainment System (NES) using Atmel Microcontrollers. We decided early on the adding audio to the mix was likely going
to be too much work in the time that we had to…... Listed under: Sound - Audio Projects
1129. Laser Audio Transmitter Using Atmega32 Introduction This project is a proof-of-concept device that transmits an audio signal
using a laser beam, while removing the need for the user to align the beam themselves. For our project, we created a mono-
axial transmitter/receiver setup that converts an analog audio signal, via a…... Listed under: Radio Projects, Sound - Audio
Projects
1130. Voice Tuner and its Effects Using Atmega644 Introduction Sound Bite Our project implements a tuner that continuously
outputs the frequency of an input microphone signal with a high degree of accuracy. Project Summary This project's goal is
to use a sensitive microphone, computer speakers and a properly designed circuit so that for…... Listed under: Sound - Audio
Projects
1131. Wireless Music Player Using Atmega32 Our wireless music player allows the user to listen to uncompressed digital audio
streamed over a wireless link. The music player reads uncompressed audio data from an SD card in an immobile "base
station." A pair of Xbee transceiver modules are used to stream data…... Listed under: Radio Projects
1132. Multisensor Data Transmission Using Atmega32 Introduction For our final project we built a prototype of a circuit intended
for a picosatellite that measures temperature and acceleration, sending the information wirelessly back to a base station
receiver. The N-Prize is an amateur rocketry competition challenging groups to launch a very small…... Listed under: Sensor -
1133. Heliostat Skylight Using Atmega644 Introduction With the increasing awareness of sustainable and green building, more and
more people are concerned with the efficiency of energy use at home and at work. For our ECE 476 Final Project, we
developed a microcontroller-based, interior illumination system - The Heliostat Skylight. By…... Listed under: LED Projects
1134. Wii Conductor Using Atmega32 Introduction Our project can be described as a simplified implementation of Wii-Music,
utilizing a Nintendo Wii Remote (Wiimote) to play a gesture-based music game with the player as a virtual music conductor.
We decided to do this project since it exploited two of the Wiimotes…... Listed under: Interfacing(USB - RS232 - I2c -
ISP) Projects
1135. Musical Blocks Using Atmel ATmega 644 ntroduction The purpose of this project is to create musical blocks that output music
without requiring some sort of musical talent. Musical Blocks tracks the position of the blocks on a flat surface in a range
seen by the Wiimote. The path of the blocks…... Listed under: Sound - Audio Projects
1136. Programmable Synthesized Guitar Using Atmega644 Introduction Our project recreates the experience of playing an acoustic
guitar electrically using vibration sensors, push buttons and the Karplus-Strong algorithm. Our basic idea is to model an
acoustic guitar as closely as possible and then implement additional functions not available to the conventional guitar.…...
Listed under: Sound - Audio Projects
1137. Robot Plotter Using Atmega32 Motivation Deciding a direction of the final project in ECE 4760 can be very difficult. With
small Micro Controller Unit, we can build anything and everything. We felt compelled to find something very creative and
ingenious and had looked around our surrounding and have found…... Listed under: Robotics - Automation Projects
1138. PowerBox: The Safe AC Power Meter Using Atmega32 Introduction We designed a device that measures and graphs various aspects of AC power and
acts as a computer-controlled remote switch. With the recent push for green energy and environmental friendliness, more and more people are
concerned about their personal daily power usage. We developed…... Listed under: Calculator Projects

1139. Rhythm Ring: Interactive Rhythm Sequencer Using Atmega32 I. Introduction The Rhythm Ring interactive rhythm sequencer
is an engaging musical device that enables the user to create a plethora of rhythms and beat patterns with the touch of their
own fingers. Besides being fun to play with, the Rhythm Ring provides a tangible…... Listed under: Sound - Audio Projects
1140. Trumpet MIDI Controller Using Atmega32 The Trumpet MIDI Controller allows trumpet players the freedom of synthesizing
from and composing on their native instrument. The Trumpet MIDI Controller combines custom hardware and software with
the Yamaha Silent Brass pickup mute to convert any standard trumpet into a fully functional MIDI controller…... Listed under:
1141. Air Drums Using Atmega32 Introduction One Sentence Sound Bite Air Drums is an electronic drum kit played in the air that
eliminates the need for tactile drum pads. Summary We created an electronic percussion set with three upright percussion
sounds and a floor bass drum sound. The upright instruments…... Listed under: Sound - Audio Projects
1142. Dueling Banjos Using Atmega32 Introduction Our project was to create two individual microcontrollers that can play banjo
notes cooperatively to play two-part songs using nothing but sound to communicate and synchronize. Humans have had the
ability to synchronize musical instruments together to achieve a single, coordinated multi-part song for…... Listed under:
1143. Intelligent wireless pedometer Using Atmega32 Introduction For our ECE 476 Final Project, we have built an intelligent,
wearable pedometer. This wireless pedometer can calculate many useful statistics such as the number of steps a user has
taken, the distance and the speed the person has walked/run, as well as the…... Listed under: Internet - Ethernet - LAN
Projects
1144. Networked Biometric Authentication Using Atmega32 Introduction: Due to the increasing need for securing data and places,
the biometric authentication industry is seeing large market growth. We decided to build a scalable, small, and efficient
device that can be used to secure doorways throughout a complex. We use a FingerPrint Cards…... Listed under: Calculator
Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1145. 5x5x5 LED Cube – Orientation Independent 3D Display Using Atmega32 Introduction Our project, in one sentence, is an
orientation independent 3D LED display. We were inspired by various videos on youtube of similar cubes but also by the idea
of creating an interactive 3-dimensional display. We built a 5x5x5 LED cube display and controller board…... Listed under: LED
Projects
1146. BordFree Using Atmega32 Introduction BordFree is a resurrection of the classic Microsoft hit SkiFree featuring an innovative
tilt-control scheme. BordFree places users in the boots of a snowboarder navigating a challenging ski slope. BordFree players
will see their character on a color TV scrolling from bottom to top…... Listed under: Game - Entertainment Projects
1147. High Speed Photography Controller Using Atmega32 The goal of this project was to build a versatile, yet easy to use, sensor-
triggered camera controller for high speed photography. Dan Furie (djf35) Scott Linderman (swl28) High Level Design
Inspiration Our motivation came from photographs that captured a very small moment in time, such…... Listed under: Sensor
1148. 3D Maze in a Box video game Using Atmega32 Introduction Maze in a Box is a portable game in which you tilt a TV to
navigate your way around a 3D maze as though you were in it. We created Maze in a Box as a challenge to generate 3D
looking graphics using the…... Listed under: Game - Entertainment Projects

1149. 3D Video Game Control Using Atmega32 Introduction Our project is a 3-dimensional game control for a video game
displayed on a black and white television set. Motivation and Overview In the recent push in technology, many new computer
and game interfaces have been created, many of which include wireless control. Our…... Listed under: Game - Entertainment
Projects
1150. Gesture-driven Tetris Using Atmega32 Introduction Our project takes a classic video game and adds a twist with a handheld,
gesture based controller. IT'S SUPER TERRIFIC AMAZING TETRIS EXTREEEEEEEEEEEME!!!!!!! We decided to undertake this
project because the idea of combining the massive coding required for the Tetris game with the…... Listed under: Robotics -
Automation Projects
1151. Data Acquisition System With Controller Area Network and SD Card Using Atmega32 Introduction This project implements a
high speed data acquisition system using Mega32 microcontrollers and a Controller Area Network (CAN). Recording data is
essential to testing and developing a racecar. Recording what each sensor is doing can tell an engineering how the car is
performing, and…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
1152. Automotive On-Board Diagnostics Reader Using Atmega32 Introduction Our project is a hand-held device that is capable of
communicating with any vehicle that uses pulse-width modulation (PWM) data-link layer. Such devices are commonly
referred to as On-Board Diagnostic scanners. Vehicles that typically fall into this category are Fords made between 1996
and…... Listed under: Car Projects
1153. Neural Net Helicopter Using Atmega32 Introduction and High Level Design Our project was to design a two degree-of-
freedom stationary helicopter, autonomously controlled by an evolving neural network. A normal helicopter has six degrees
of freedom, which makes any form of control exceptionally hard, let alone autonomous control. What our design…... Listed
1154. Accelerometer Controlled R/C Vehicle Using Atmega32 INTRODUCTION In our final design project for ECE 476:
Microcontrollers, we decided to build a vehicle controlled, using accelerometers, by a remote control that wirelessly
transmits, using RF technology, data to the vehicle to move in any direction. The accelerometers will be mounted on a…...
Listed under: Car Projects
1155. ROBOT ARM Using Atmega32 Introduction Our project is a twenty four and half inch aluminum frame robotic arm with four
degrees of freedom. In our project we made the arm the second player in the classic game of Tic-Tac-Toe to demonstrate its
programmable repeatable motion. The arm consists of…... Listed under: Robotics - Automation Projects
1156. Help Quit Smoking Watch Using Atmega32 Introduction: The Help Quit Watch is a watch that smokers can wear to help them
quit smoking. The Help Quit Watch contains a smoke detector that detects whenever the smoker smokes and plays an
encouraging clip to help the smoker stop. It then records statistics…... Listed under: Medical - Health based Projects
1157. Electronic Impact Vest Using Atmega32 Our one sentence "sound byte"... *POP* Finally, a fair and balanced way to score Tae
Kwon Do matches without the moaning and groaning of everyone. The Electronic Hogu system uses piezoelectric force
sensors to determine how much force is delivered by the impact of a…... Listed under: Sensor - Transducer - Detector Projects
1158. TriWheeler robot Using Atmega32 Introduction The TriWheeler is a radio-controlled robot with three wheels. The lack of the
fourth wheel is far from the only thing that renders it distinctively different from typical radio-controlled units. In addition to
the capability of being freely controlled with a remote control, The…... Listed under: Robotics - Automation Projects
1159. Music Wand: Real-Time Optical Scanning of Sheet Music Using Atmega32 Introduction The Music Wand is a device that optically reads printed sheet
music in real-time and synthesizes the notes which are read from the page. The device uses a linear image sensor mounted on the end of a handheld
wand to scan printed sheet music…... Listed under: Sound - Audio Projects

1160. Teaching an old clock Using Atmega32 While exuding retro style, the alarm clock in its original state lacked many desirable
features of today's alarm clocks. The only controls consisted of a single on/off switch. It also lacked AM/PM indication,
making it impossible to sleep for more than 12 hours. Our project…... Listed under: Clock Projects
1161. Shark Tag Microcontroller Platform Using Atmega32 Introduction The goal of this project was to develop a working bench-
top microcontroller platform for a shark tag. It is to be used for on-animal, in-situ data logging applications involving sharks
and potentially other large pelagics. For this project I used the Atmel Mega32 microcontroller…... Listed under: Sensor -
1162. Ghost Writing Robot Using Atmega32 Summary We used two stepper motors to drive a steel ball scavenged from a ball-
bearing. These motors were controlled by a PS/2 mouse wirelessly using the RCR-433 and RCT-433 receiver/transmission
combination mentioned in lecture. We then took the PS/2 protocol, made it compact, modified existing…... Listed under:
1163. Rocket Inertial Navigation System using Atmega32 Introduction Was that a ... projectile? a rocket? an [XXXXX] missile? That
was a dynamically controlled parachute guidance system looking for its target. The purpose of this project was to design a
dynamically controlled parachute guidance system using an Atmel ATmega32 microcontroller. A set of…... Listed under:
1164. Guitar Tuner Using Atmega32 Introduction: Motivation for Design The Mechanix is a motorized guitar tuner for a standard 6-
string electric or acoustic fixed bridge guitar. Named in honor of Megadeth guitar legend Dave Mustaine, the Mechanix is a
unique and innovative product which has numerous patent possibilities. Traditional handheld…... Listed under: Sound - Audio
Projects
1165. SCHEME INTERPRETER USING ATMEGA32 Introduction The purpose of this project is to create a Scheme interpreter using C
language and Mega32 microprocessor. Using limited resource and memory in the microprocessor, the interpreter should
function and work for basic Scheme commands. The main target of the project is to use…... Listed under: Microcontroller
Programmer Projects
1166. Mini-Golf Simulator Using Atmega32 Introduction This project simulates 9 holes of a minigolf course using the TV to display
the course (top down view), an anchored plastic ball containing two accelerometers, and a putter. Summary We used a
hollow plastic ball containing two accelerometers for each planar axis with…... Listed under: Game - Entertainment Projects
1167. Battle Tank – A 3d Atmega32 Based Video Game Introduction Our project is a wireframe 3D video game based on the classic
Atari arcade game, Battlezone (Copyright Atari Corp, 1980). For those that have never heard of the game, Battlezone is a
game in which the player maneuvers a tank through a flat environment,…... Listed under: Game - Entertainment Projects
1168. LaserSimon – An Innovative Take On An Exciting Game Using Atmega32 Inspiration Our project was first inspired by our
shared enjoyment of classic laser tag. We initially started out with a game in mind that entailed playing two player laser tag
with remote-controlled helium blimps. Due to a number of logistical issues that came up while…... Listed under: Game -
1169. Snake Arm Glove Project Using Atmega32 Introduction For our project, we designed a glove that can be used to control the
Cornell University robotic Snake arm thereby enabling a surgeon to remotely operate the snakearm as a colonoscope in
conjunction with a vision guide system (aka TV goggles). The glove allows…... Listed under: Robotics - Automation Projects
1170. Wiimote Crane Using Atmega32 I. Introduction We used the Wiimote’s IR tracking capability and Bluetooth to wirelessly control a robotic crane arm.
The Wiimote is a powerful gadget and we wanted to build a new hack with it. Our crane is composed of three servo motors, one of which…... Listed
under: Game - Entertainment Projects, Robotics - Automation Projects

1171. Radio Frequency Beacon Finder Using Atmel Mega32 This project is a radio frequency receiver that will help the user the
trace the direction and distance of transmitter beacon(s) operating at 433MHz frequency. In this ECE 476 final project, we
have built a radio frequency receiver unit with an LCD screen that will…... Listed under: Radio Projects
1172. A portable, color, tilt-controlled video game system Using Atmega32 Introduction The Weeboy is a portable color video
game system that is not dependent on stationary displays or external power sources and features novel tilt-based control.
Our purpose for designing this project was to demonstrate that a complete portable video game system could be
implemented…... Listed under: Game - Entertainment Projects
1173. TouchPad video game Using Atmega32 Content Page 1. Introduction 1.1 Sound-Bite Our final project recreates
Rush Hour as a video game that is played using a touchpad implemented using 2D electric-field (E-field) sensors.
1.2 Motivation Rush Hour appealed to us as one of the better puzzles out there. Its level of difficulty…... Listed under:
1174. Music-controlled Puppet Using Atmega32 Introduction The purpose of this project was to design a dancing puppet which is
musically controlled by the microcontroller. This is a simple, inexpensive dancing puppet, which can dance to any tune you
want. For as little money as possible, you can bring Pinocchio to…... Listed under: Sound - Audio Projects
1175. Line-following car Using atmega32 Introduction Our project is a battery-powered toy car that is able to follow a
path against a background of contrasting color. <> The front of the car is fitted with an array of three photosensors,
which allows the car to detect the path…... Listed under: Car Projects
1176. PeanutBot, The Audio Homing Robot Using Atmega32 Introduction Sensing in autonomous vehicles is a growing field due to
a wide array of military and reconnaissance applications. The Adaptive Communications and Signals Processing Group (ACSP)
research group at Cornell specializes in studying various aspects of autonomous vehicle control. Previously, ACSP has
examined video…... Listed under: Robotics - Automation Projects
1177. Model retina: color tracker Using Atmega32 Objective and Background <> Objective: The gift of sight is precious; that is why
we tried to model an artificial retina with the properties of color detection, saccades, and pursuit tracking. Structure of a
Retina: A retina lies in the back of the eye and…... Listed under: Sensor - Transducer - Detector Projects
1178. Evolving neural robot Using Atmega32 Introduction Our final project in ECE 476 is a mobile robot with a developed neural
network such that it evolves to avoid collisions into a circular vertical white wall while traveling at the fastest speed and
straightest line possible without human intervention or external computers.…... Listed under: Robotics - Automation Projects
1179. MCU MIDI synthesizer using Atmega32 Introduction Our final project is a music synthesizer that is capable of producing a
variety of musical sounds, by modify, the attack, decay, sustain, release times, and applying special effects such as a low pass
filter or a halftone shifter. Our original interest for this…... Listed under: Sound - Audio Projects
1180. AirJam: wearable air guitar Using Atmega2 Introduction Why a working, wearable air guitar? Bottom line, it's just that cool.
Who doesn't want a machine that will take their jamming and turn it into rock they can hear? With just a glove, a pick and a
little practice you can rock the…... Listed under: Sound - Audio Projects
1181. UDP/Ethernet Controlled Temperature Regulator Using Atmega32 Introduction This project implements a microcontroller based temperature
regulator which can be controlled via the Ethernet port on any common personal computer. As the world becomes more networked, the power of our
ability to communicate with many different systems instantly continues to prove it's worth…... Listed under: Temperature Measurement Projects

1182. Morse code interpreter, with speech synthesis Using Atmega32 Introduction This project implements a system that translates
Morse Code to text and speech and translates text to Morse Code. With our limited experience with Morse Code, our first
task was to do some research on the components of Morse Code and the standards associated…... Listed under: Sensor -
1183. Complex impedance analyzer Using Atmega32 Introduction Our device is an impedance analyzer that determines the
complex impedance of any R-C circuit within an impedance range. Our original plan for creating this device was to develop a
body fat measurer, a portable device that could allow users to monitor their health…... Listed under: Other Projects
1184. iPod controller Using Atmel Mega32 Introduction Have you ever imagined, "What does that cable I plug into my iPod every
day actually do, and how do I take advantage of it for myself?" We did too, and that's what we aimed to do with our 476
project. The iPod is,…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
1185. USB Magnetic Mouse/Touchpad Using Atmega32 Introduction Many digital artists draw with mice on computer or use
tablets. However, tablets are often very expensive. Using the mouse is not always as accurate and one needs a steady hand.
Our project attempts to create a lower budget alternative to the tablet that…... Listed under: Sensor - Transducer - Detector
Projects
1186. Braille reader using Atmel mega32 Introduction BlindAid is a portable tool that reads Braille and signals close objects. It is
ideal for those unfortunate people who just turned blind and have not mastered Braille reading and blind cane usage. It can
also be used as a learning instrument that helps…... Listed under: Home Automation Projects
1187. Ultrasonic ParKontroller Using Atmel Mega32 Introduction Are you afraid that your brand new Hummer is going to get
scratched while parking it in a tight space? Do you have trouble backing your large Mercedez S-class into your small
garage? Fear no more! Our ultrasonic ParKontroller can sense how far you…... Listed under: Car Projects
1188. Retractable Alarm Clock (RAC) Using Atmel Mega32 1.1 Motivation: Alarm clocks are essential in almost everyones daily life.
For most of us, we start our day to the sweet noise of our alarms. While some people wake up instantaneously to the first
chirp of an alarm, some struggle everyday to get out…... Listed under: Clock Projects
1189. Automatic pet feeder Using Atmel Mega32 Introduction Our project is an automated pet feeder that is controlled by a
wireless infra-red remote control. As pet lovers, we understand that the responsibilities of life sometimes inhibit pet owners
from properly caring for their pets. Pet care should be fun, not burdensome, and…... Listed under: Home Automation Projects
1190. Programmable medication scheduler using atmel mega32 Introduction The Newest Innovation in Patient Compliance The
Portable Programmable Medication Scheduler (PPMS) is a modern solution to the century old problem of patient
compliance, featuring four medication bins, audio/visual alarms, a graphic LCD, and serial communication with a Java Swing
PC GUI. The conjunction…... Listed under: Medical - Health based Projects
1191. CalcParser Using Atmel Mega32 Introduction CalcParser is a command line calculator. Controlled by a serial connection,
CalcParser parses and evaluates an arithmetic expression and has the capabilities to perform symbolic polynomial
differentiation with respect to a user-defined variable. It can also evaluate the differentiated expression at a given
constant…... Listed under: Calculator Projects
1192. Firefly synchronization Using Atmega32 Introduction This project implements a 2D matrix of bidirectional LEDs to simulate
how fireflies in a population synchronize their flashing. Fireflies are an extraordinary species of bioluminescent animals which
are able to synchronize the timing of their light emission within a flashing population. In places…... Listed under:
1193. Graphing calculator Using Atmel Mega32 Introduction A perfect tool for high school students that will pursue a career in engineering, the graphing
and statistics calculator combines the functionality of a scientific calculator with graphing capabilities as well as being able to compute simple
statistics. The purpose of this calculator is…... Listed under: Calculator Projects

1194. Speech Recognition Jukebox Using Atmega32 Introduction For the Final Project in ECE 476: Designing with Microcontrollers,
Robbins and Saha developed a Speech Recognition Jukebox, comprised of a speech recognition system that activated a
simple music player. The speech recognition system was capable of recognizing four commands and could cycle through…...
1195. Sound Source Triangulation Game Using Atmega32 Introduction The goal of this project is to determine the time and
location of a sound source in all three dimensions (x,y,z) using an economical and easily reproducible setup. To accomplish
this goal, we decided to try and triangulate the sound source using a 4…... Listed under: Game - Entertainment Projects
1196. Touch Screen Controlled R/C Car Using Atmel Mega32 Introduction For our final design project, we chose to build a touch
screen radio controlled car. Essentially, the RC car will follow a path drawn by the user on the touch screen as it is drawn in
real time. Speed and direction of the car…... Listed under: Car Projects
1197. AppleII emulator Using Atmel Mega32 The goal of this project was to develop a system capable of emulating an Apple II
personal computer. This project attempted to reconstruct a functional Apple II emulated on Atmel ATmega32 processors. Due
to time constraints, a fully functional Apple II was not produced; however,…... Listed under: Microcontroller Programmer
Projects
1198. HDD analog clock with LCD touchscreen Using Atmel Mega32 Introduction The clock is one of the oldest inventions in
human history and has been used for centuries as in instrument for measuring time. There are many ways to implement this
ancient technology by simple and practical methods. However, si [caption id="attachment_18482" align="aligncenter"
width="531"] HDD…... Listed under: Clock Projects, LCD Projects
1199. CUAUV Voltage Sniffer Using Atmel Mega32 Introduction The Cornell University Autonomous Underwater Vehicle team
(CUAUV) is an undergraduate engineering team that designs and builds a fully autonomous, robotic submarine. Over the
past year, the team – of which both Manoj Lamba and Ian Wang are members – has had a stringent…... Listed under:
Metering - Instrument Projects, Sensor - Transducer - Detector Projects
1200. CUsat diagnostic board using Atmel mega32 1 Introduction Our final project is the CUSat Diagnostic Board (CUDB). This
board will be used for monitoring CUSat system health as well as performing various functions allowing for easy integration
and debugging of CUSat components. [caption id="attachment_18448" align="aligncenter" width="600"] CUsat diagnostic
board using Atmel…... Listed under: Development Board - Kits Projects
1201. SearchBot Using Atmel Mega32 Introduction The SearchBot is a fully functional model car that can be controlled wirelessly
through the PC or autonomously search for red balls scattered on a flat surface. Autonomous vehicles are just now being
realized in labs around the world and will soon have major…... Listed under: Car Projects
1202. Robotic Vacuum Cleaner Using Atmel Mega32 Introduction As our final project, we decided to design and build a robot
capable of vacuuming the floor of a room or area without any human interaction other than just starting the unit. We realized
the need for a cheap and convenient product that can…... Listed under: Robotics - Automation Projects
1203. Cooler-Bot Using Atmel Mega 16L Introduction Cooler-Bot is an autonomous vehicle that uses ultrasonic transducers to
sense distance and direction to a remote ultrasonic mobile unit that it is designed to follow. Our original goal was to design a
vehicle that would carry a beverages for the user and follow…... Listed under: Car Projects
1204. MCU/FPGA color video Game Platform Using Atmel Mega32 Overview: A system consisting of an ATMEL MEGA32 chip, Altera
FLEX10K FPGA, and a library of source code for the Atmel processor to generate 256-color VGA video signals in real time
optimized for game development. Introduction: The Nintendo Entertainment System sports 2 KB of RAM…... Listed under:

1205. Musical Water Fountain Using Atmega32 Introduction Our final project is a musical water fountain loosely based on the
fountain in front of the famed Bellagio hotel and casino. The basic idea of the project is to take an input from an iPod (or any
sound source), sample the sound and…... Listed under: Sound - Audio Projects
1206. Machine de Karaoke Using Atmega32 Introduction Sound bite Our project is a karaoke recording machine which is capable
of removing the voice component of a music file and storing the users singing voice with the background music to an
external compact flash memory. It can also be used as a…... Listed under: Sound - Audio Projects
1207. Dual Control R/C Car Using Atmega32 The purpose of this project was to take a traditional remote controlled car and create
our own control mechanisms. To control the car, we used a dual-axis accelerometer and LEDs (light emitting diodes)
configured as photo-detectors. The control mechanism was selected using a single pole…... Listed under: Car Projects, Game -
Entertainment Projects, Sensor - Transducer - Detector Projects
1208. Guitar Synthesizer and Game Using Atmega32 Introduction Compose your own virtual guitar masterpiece or follow along
with a preprogrammed classic. No experience needed! We developed a guitar synthesizer with video component inspired by
the popular video game Guitar Hero. The original game consisted of only reproducing popular rock and roll songs…... Listed
1209. Lighting control system Using ATMEL Mega32 Loucetios™ is a state-of-the-art, self-configuring lighting control system
solution for bedrooms, offices and perimeter areas. Under automatic operation, the system senses luminosity inside and
outside a room, controls the angle of the blinds and dims the lamps to maintain a prescribed level of illumination inside…...
1210. Intelligent Multimedia System Atmel mega32 Introduction This project implements a multi-function multimedia system that
allows the user to sing with the music video and generate some fancy sound effects. In recent decades, multimedia becomes
quite popular in our daily life. In fact, multimedia system has existed for a long time.…... Listed under: Game – Entertainment
Project Ideas, Sound - Audio Projects
1211. Ultrasonic spotlight tracker using Atmel mega32 Introduction A spotlight that follows you on its own! The ultrasonic spotlight
tracker is a system that uses a wireless beacon to track a targets location using both RF signals and ultrasound waves. It then
drives a light source to point at the location of…... Listed under: Sensor - Transducer - Detector Projects
1212. Galvanic skin response meter using Atmel mega32 Introduction Our project measures the user's skin conductance for
monitoring his or her mental state. Summary Medical experiments have shown that the magnitude of the electrical
conductance in a person's skin is directly correlated to their emotional state. The short term changes in electrical
conductances…... Listed under: Metering - Instrument Projects
1213. VOICE RECOGNITION SECURITY SYSTEM USING ATEGA32 When we think of programmable speech recognition, we think of
calling FedEx customer service call center with automated voice recognition response systems. We also think of PC-based
speech recognition Dragon NaturallySpeaking. Now we took that a step further. We are talking about speech recognition
in…... Listed under: Security - Safety Projects
1214. SecureLED: Better Access Control Using ATMega32 Introduction Overview SecureLED is an optical access control device which
replaces current RFID or Magnetic Strip technologies with a cryptographically secure, contact-less device which
communicates over commodity Light Emitting Diodes (LEDs). Project Summary This project started with one central premise:
current physical access control systems…... Listed under: LED Projects
1215. Capacitance sensor MIDI keyboard Using Atmel mega32 Introduction The objective of this project was to build a keyboard
based on capacitive sensors and then use the MCU to create MIDI encodings for all notes played. The output from the
sensors is detected by the MCU using its ADC capability. The sound is…... Listed under: Sensor - Transducer - Detector
Projects
1216. The Grillzilla Using ATMega32 Introduction: One Sentence Sound Byte: “Grillzilla - A wireless meat grilling thermometer which alerts the user whether
their entrée is cooked according to USDA recommendations via LCD and voice feedback.” Summary of what we did: As the weather starts to get
warmer a common type…... Listed under: Home Automation Projects, RFID - NFC Projects

1217. Sign language coach Using Atmega32L Introduction Objective The goal of this project is to design a useful and fully
functional real-world product that efficiently translates the movement of the fingers into the American Sign Language.
Background The American Sign Language (ASL) is a visual language based on hand gestures. It…... Listed under: LCD Projects,
Robotics - Automation Projects, Sensor - Transducer - Detector Projects
1218. Radial Chalker Using Atmel Atmega32 Introduction We developed a new way for student groups to chalk advertisements for
events. This project is a radial printing device for drawing with chalk/markers on flat surfaces. High-Level Design dea
Rationale and Sources Anyone who has done any sidewalk chalking knows that it is…... Listed under: Motor Projects
1219. GoConn Bicycle Computer Using Atmega 32 Introduction This project is a bicycle computer that includes velocity monitoring,
calorie computation, an audio/visual alarm, and a wireless remote. Bicycles are great for transportation as well as exercise.
Unfortunately, many bicycles across campus and around the world are stolen everyday. We designed a computer…... Listed
under: How To - DIY - Projects
1220. Handwriting Recognition System Using Atmel Mega32 I. Introduction Simply write; your computer will undersand! We
have designed and implemented a Handwriting Recognition System using a touch screen from a Palm Pilot m125, a black
and white TV and a Mega32 microcontroller. Unfortunately, due to the lack of specifications regarding the built-in…... Listed
under: LCD Projects, Sensor - Transducer - Detector Projects
1221. Programmable remote control Using Atmega32 Introduction The goal of our project was to develop a remote control whose
buttons would be readily programmable by recording the signal from another remote control. After revising several
standards on infrared signals, we determined that the approach to take was to record the signal…... Listed under: Sensor -
1222. Flat Bed Scanner Using Microcontroller Introduction Quite possibly the slowest and lowest resolution of any scanner on
the market today, but it sure is mesmerizing to watch.. and it actually works! That's about the best way to describe this
behemoth of a project, which involved countless hours of building,…... Listed under: CNC - Printing Machines Projects
1223. Digital Stethoscope Using Atmega32 Introduction Our project is a digital stethoscope that displays your heartbeat on any
television. It also calculates beats per minute and alerts you if your rate falls out of a specified range. [caption
id="attachment_17908" align="aligncenter" width="234"] Digital Stethoscope Using Atmega32[/caption] At the highest level,
the…... Listed under: LCD Projects, Medical - Health based Projects, Sensor - Transducer - Detector Projects
1224. TRISHUL -Autonomous navigating robot Using Atmel Mega32 Introduction We decided to do this project due to our keen
interest in the robotics. We were also looking for a project that involved a perfect mix of hardware and software complexity.
This project enabled us to use new hardware such as sensors, stepper motors…... Listed under: Robotics - Automation
Projects
1225. Nova Strike video game Using Atmega32 Introduction Nova Strike is a 2D space shooter game implemented with an Atmel
ATmega32 microcontroller. The inspiration came from our love of video games and fond memories of playing space shooters
on our TI-89 graphing calculators in high school (instead of paying attention in calculus…... Listed under: Game -
1226. Digital Compass Using Mega 32 I. Introduction The goal of this project is to build a digital compass that displays both the
direction and cardinal points on a television. Other functionalities were added to complement the sensor interface, such as,
temperature display, magnetic declination input and disability option. At the…... Listed under: Sensor - Transducer - Detector
Projects, Temperature Measurement Projects
1227. MiniGolf video game with putter Using Atmel Mega32 Our project is creating a miniature golf game, complete with a putter
and golf ball to simulate a real putting stroke. We chose to construct a mini golf game because not only is it interesting, but
it has a large balance of computer programming as…... Listed under: Game - Entertainment Projects
1228. Electr-O-Sketch Using Atmega 32 Introduction We created a project in which a user could control the movement of an Etch A Sketch using a typical
serial mouse. The public was introduced to the EAS in 1960 and since then it has stayed virtually the same. This nostalgic toy is…... Listed under:

1229. Pong2 Using Atmel Mega32 Introduction PONG, a video game that simulates a game of Ping-Pong between two players, has
a long and pervasive history, and is said to be the first video game ever created. For our final project, we decided to pursue
PONG with a twist. We designed…... Listed under: Game - Entertainment Projects, LCD Projects
1230. Handheld Ultrasonic Rangefinder Using Atmel Mega32 Introduction Our ultrasonic rangefinder is capable of allowing the
user to determine his or her distance from an object or wall. When deciding on what type of project to design and construct,
we decided that we wanted to create something that would have some practical…... Listed under: LCD Projects, Sensor -
1231. Beverage Monitor Using Mega32 Introduction We created a wireless device to affix to the bottom of a pitcher that alerts the
wait staff when the pitcher is empty. We used the a priori knowledge that when a pitcher is empty the pitchers bottom is
perpendicular to the ground. By…... Listed under: Sensor - Transducer - Detector Projects
1232. The Ultimate MP3 Radio Using ATMega32 Introduction Perusing through the impressive list of past projects, we decided to
make our final project a combination of two technologies—wireless technology and the MP3 player. Specifically, we decided
to create an MP3 player that broadcasted the songs to an FM dial. We call this…... Listed under: Internet - Ethernet - LAN
Projects, Sound - Audio Projects
1233. SmartBlinds Using Mega32 Overview The SmartBlinds system uses a microcontroller to control the angle of a set of
miniblinds used at home, in the classroom, or on the job. Using SmartBlinds, a user can more effectively control the light
coming into the room, or have an alarm that…... Listed under: Home Automation Projects
1234. Keypaw Using Atmel Mega32 1 Introduction The Keypaw is a 12-button input device that provides computer users with an
ergonomic, fully-configurable alternative to the traditional QWERTY keyboard. The Keypaw is a microcontroller-driven device
with 12 buttons mounted on two handsets; 1 button is provided for each finger, and 2…... Listed under: Development Board -
Kits Projects
1235. Home Security System Using Atmel Mega32 Introduction This is a digital home security system with voice feature which can
monitor room temperature, smoke, motion, and windows & doors. The goal of this project is to utilize the after-market parts
and build an integrated home security system. Besides traditional magnetic switch equipped…... Listed under: Security -
Safety Projects
1236. A Wand Based Barcode Scanner Using Atmel MEGA32 Introduction Our project is a UPC-A Barcode Scanner complete with a
pricing/description database interface. Our original goal for this project was to build a standard barcode scanner from
scratch, but as the project evolved so had to our specification of the project. We initially sought…... Listed under: Metering -
Instrument Projects, Sensor - Transducer - Detector Projects
1237. Implementation of a (31, 16) BCH code on a Microcontroller Using Atmega32 Introduction: Error correcting codes are used
throughout digital communication systems today. Cell-phones, CD players, satellites, digital pagers and many other
communication devices all use varying amounts of error control to achieve a certain degree of accuracy in transmitting
information. The idea behind error control codes…... Listed under: Radio Projects
1238. The Breath-o-Matic Using Atmega32 Introduction Let us introduce the Breath-o-Matic alcohol sensor. The Breath-o-Matic is
an electronic, non-invasive method of measuring a human’s blood alcohol content (BAC). Its elegant, yet discombobulated
design embodies a cheerful mix of mechanical and semiconductural components. Simply blowing into the mouthpiece
causes the Breath-o-Matic…... Listed under: Sensor - Transducer - Detector Projects
1239. TV/Keypad Interface for Winamp Using Atmel MEGA32 MP3 is presently a household term; the reader will likely own a few, barring any intervention
from the RIAA. Since it's not always practical to sit in front of a monitor and keyboard when you want to listen to music (e.g. in a car, on…... Listed

1240. Eye in the Sky Security System Using Atmel Mega32 Introduction We have used the Atmel Mega32 AVR microcontroller to
construct an affordable, high end security system designed to protect valuables in a single room of a house or property.
According to national surveys conducted by the department of Justice, property crimes are ten times…... Listed under:
1241. Xylophone Using Mega32 Introduction Our final project is a programmable, self-playing xylophone with random melody
generation and a pitch detection based interface. From early mechanical devices to todays musical greeting cards, history has
seen numerous examples of automated music machines. This project represents a quick, modern take on…... Listed under:
1242. Scorched Earth video game using Atmel Mega32 For our design project, we decided to replicate the video game known as
Scorched Earth: The Mother of All Games where two tanks fire missiles at one another by adjusting angles and power while
adjusting for variable wind. The objective of Scorched Earth is to…... Listed under: Game - Entertainment Projects
1243. Wonderswan Development Cartridge Using Atmel Mega32 Introduction Short Summary This project allows a Wonderswan
developer to upload 64 kB of code/data and execute it on real Wonderswan handheld gaming hardware. Long Summary We
started by opening up one of our Wonderswan cartridges and identifying the various chips and circuitry found inside.…...
Listed under: Game - Entertainment Projects
1244. Star Duel video game Using Mega32 1. Introduction 1.1 Project Summary Our project is a space dogfighting video game
where two players attempt to destroy each other using a variety of ships and weapons. The battlefield is a 128x100 pixel area
on a TV, and a small planet resides in the…... Listed under: Game - Entertainment Projects
1245. The Big Red Guide Using Atmel AVR Mega32 If this is your first time on the Cornell Campus, you need not worry! Cause we
have the best guide for you! Introduction The Cornell Campus is quite large, and finding your way around can get a bit
frustrating. The Big Red Guide is a…... Listed under: GPS Based Projects, Security - Safety Projects
1246. MISSILE COMMAND USING ATMEL MEGA 32 Introduction For my ECE 476 Design Project, I built Missile Command using the
Atmel Mega 32 microcontroller. My version of Missile Command is based on Ataris 1981 version. After looking at some of
the past ece476 final projects, I noticed no one had tried to…... Listed under: Game - Entertainment Projects
1247. 3D gForce Mouse Using Mega32 Introduction "Our 3D gForce Mouse will enable use to move the curser in the air freely with
the capacity of scrolling" The rationale for this design is two fold. We wanted to do this design because we wanted to make a
zero-impact pointing device for…... Listed under: Sensor - Transducer - Detector Projects
1248. Stationary Helicopter Using Atmel Mega32 Intro Summary Thinking about what a CDE (culminating design experience)
should be, we devised a project that combines the microcontroller programming principles learned in ECE 476:
Microcontroller Design with the control theory concepts learned in ECE 472: Feedback Control Systems to create an
academically viable…... Listed under: Motor Projects, Sensor - Transducer - Detector Projects
1249. INFRARED TRACKING SYSTEM USING ATMEGA32 Introduction Infrared (IR) Our project is an infrared (IR) tracking system. A
beacon, placed on the object to be tracked, continuously emits infrared signals in all directions. The signals coming from the
beacon are detected by 2 IR receivers mounted on 2 stepper motors, which rotate…... Listed under: Featured, Game –
Entertainment Project Ideas, Sensor - Transducer - Detector Projects
1250. Arkanoid Video Game using Atmega32 Introduction [caption id="attachment_16604" align="aligncenter" width="224"] Arkanoid Video Game using
Atmega32[/caption] High Level Design After working with the ATmega family of processors for the first six lab assignments, and working extensively
with generating television screen images, we decided that a video game would be a viable…... Listed under: Game - Entertainment Projects

1251. Reversi Video Game Using ATmega32 Introduction "Our project implements the game, Reversi, on TV with a smart artificial
intelligence and a host of other features!" It's our childhood game. We were so excited when we found out that we can
actually build it for our 476 final project. We looked…... Listed under: Game - Entertainment Projects
1252. Guitar Special Effects Using Atmega32 <Introduction> In the last few decades technology has constantly pushed music
further and further into the digital realm. Digital technology has infiltrated all aspects of music-making, from its creation to
its recording, editing and production. We have decided to join this technology movement by fitting…... Listed under: Sound -
Audio Projects
1253. Tap the Dance using Atmel Mega163 Introduction Nowadays in the video gaming industry, one of the most popular
categories of game is music and motion simulation game. There are games where players are required to play the drum
according to the matching signals and the music of the game; there are…... Listed under: Game - Entertainment Projects
1254. kaOS operating system and loader using atmega32 Introduction We have created a real-time, multithreaded, preemptive
operating system called kaOS for the Atmel Mega32 microcontroller, which loads and executes programs from a Secure
Digital or MMC card. We wrote this OS and created the SD/MMC card reader as a final project for Cornell's…... Listed under:
RTOS - OS Projects
1255. Keyboard mania using Atmega32 INTRODUCTION “Keyboard mania gives users an opportunity to learn and gain a unique
taste of playing an electronic piano without the presence of a music teacher.” Summary of our Project We designed an
electronic musical instrument, called keyboard mania, able to play an octave of…... Listed under: Sound - Audio Projects
1256. ECE 476 Spring 2005 by Arthur Zhang (ayz2) and Yewen Ying (ydy2) using atmega32 Introduction Soundbyte TV Jezzball with
dangling mouse, created by Cornell ECE476 students Arthur Zhang and Yewen Ying, is a hot, new, cool, retro look back to
when times were simpler, computers were slower, and TV’s were black and white. Overview From the beginning, because
of…... Listed under: Game - Entertainment Projects
1257. Duckhunt video game using Atmel Mega32 Introduction to Duck Hunt For our final project in ECE476, we implemented a
multi-duck and multi-player version of the Nintendo classic Duck Hunt on the Atmel Mega32 microcontroller. In 1985,
Nintendo released a game for the Nintendo Entertainment System (NES) called Duck Hunt, and it…... Listed under: Game -
1258. The Contender video game using Atmel Mega32 Introduction The pitch "The Contender" is an interacting boxing game in
which the player actively participate in the game with real time punching, ducking, dodging, etc. The Description and
Motivation This game is a twist of a popular arcade game called "Mocap Boxing", short for…... Listed under: Game -
1259. The Big Red Juicer using Atmel Mega32 Introduction The Juicer is a wirelessly controlled, programmable juice maker which
will mix each ingredient of a recipe to the exact proportions every time. The Juicer will take a recipe selection serially via
either the keyboard or the wireless remote and dispense the juices into…... Listed under: Home Automation Projects
1260. Color Tetris video game using ATMega32 Color TET Brief DescriptionThe project is a color "Tetris" based game compatible
with NTSC TV. Summary and motivationThe project basically utilizes a Mega32 chip, along with a RGB-NTSC converter and a
sync generator to produce color on a standard NTSC TV. The code for a…... Listed under: Game - Entertainment Projects

1261. WeatherDog Using ATMega32 Introduction Our project was a real-time weather update system that accepted an airport code
from the user via a keyboard, looked up the code on an internet database, and displayed the resulting weather information
on a television screen. We used the PS/2 protocol, between a…... Listed under: LCD Projects, Metering - Instrument Projects
1262. Neural net robot using ATMega32 Introduction Our project consisted of an elementary eight neuron network that used
Hebbian Learning to train a robot to respond intelligently to input light stimuli. First, we decided upon a task that would
accurately denote Hebbian learning. One of the most common examples of conditional…... Listed under: Robotics -
Automation Projects
1263. Wireless Electromyograph using ATmega32 Introduction This project implements a wireless surface electromyograph that
displays the signal using a television as an oscilloscope. Electromyography detects the electrical signals that the human body
generates to contract muscles. Detecting very low voltages in the milliVolt range on the skin surface is not…... Listed under:
Internet - Ethernet - LAN Projects, LCD Projects
1264. Stepper Motor Indexer & Decoder ECE 476 Using ATmega32 1. Introduction For our final project we built an ATmega32 based
stepper motor controller which measures the angular position of the motor shaft using an optical encoder and quadrature
decoder. Our system performs 3 basic functions: (1) Communicate with a PC by means of a…... Listed under: Motor Projects
1265. A Microcontroller Based Turbidity Meter using AtmelMega32 Introduction Low-Cost Turbidity Meter for Underdeveloped
Countries Our project is a collaboration with an independent research project being conducted by senior civil and
environmental engineering student James Berg. The goal of this project is to create a low cost turbidity meter for use in
under…... Listed under: Metering - Instrument Projects, Temperature Measurement Projects
1266. A Motion Capture System Using Accelerometers using AVR Mega32 By: Kris Young and Dan Li See the results section for
movie clips of the motion capture system in action. Abstract Human-Computer interface may perhaps be both the most
limiting and liberating aspect of humans working with computers.It can, for instance, limit the input complexity…... Listed
under: Metering - Instrument Projects, Video - Camera - Imaging Projects
1267. Wireless Telemetry using Atmel Mega32 I.Introduction Soundbyte:A Wireless Data Telemetry system that receives
acceleration, proximity and external temperature data from a remote vehicle and displays them on an NTSC television screen.
The rationale behind this project is to provide the user with information regarding the vehicles acceleration, proximity to
other…... Listed under: Metering - Instrument Projects
1268. Portable Security System Using ATMega 32 Introduction Consider you are in a research lab that handles highly hazardous
material. You don't want anybody to enter the room, to even come close to the door. Or consider yourself doing something
highly confidential in a room that you would like to know if…... Listed under: Security - Safety Projects
1269. Blood Pressure Monitor Using Mega32 Introduction Our final project is to design and build a portable blood pressure
monitor device that can measure a user's blood pressures and heart rate through an inflatable hand cuff. The device is
consisted of three main parts: external hardwares (such as cuff, motor, valve,…... Listed under: Medical - Health based Projects
1270. Missle Command video game using Atmega32 1. Introduction Brian Smith and Cem Ozkaynak, two Seniors enrolled in ECE
476 at Cornell University, seek to rekindle the mood of impending nuclear annihilation by distant ‘Evil Empires’ through the
classic 1980’s video arcade sensation Missile Command. [caption id="attachment_16403" align="aligncenter" width="600"]
Missle Command video…... Listed under: Game - Entertainment Projects
1271. BlindBot usisng Atmel Mega32 MCU Introduction Our project is an autonomous toy car that tracks a high pitched audio
signal. Using two microphones, a microcontroller, and two DC motors on an existing remote controlled car and, we
implemented our own control logic to detect high pitched 3.5kHz audio signals…... Listed under: Game – Entertainment
Project Ideas, Robotics - Automation Projects
1272. Super Breakout using Atmel Mega32 Get ready for the next generation of the classic game Breakout which features a
standalone device, interactive user control, and new and improved game modes including two player cooperative and
competitive modes. Introduction Breakout is a game of speed, skill, and anticipation. The player will…... Listed under: Game -
1273. Connect Four with Programmable Infrared Receiver Atmel Mega32 We have designed a programmable infrared receiver which can utilize any pulse
coded IR signal to play Connect Four from a remote distance. The programmable infrared receiver device we have created can decode any pulse-
width modulated signal of an IR remote control, store it in…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects, Radio Projects

1274. MIDI DRUM CONTROLLER USING MEGA 32 MICROCONTROLLER [ INTRODUCTION ] MIDI Drum Controller Our Final Project
for ECE476 was to build a MIDI drum machine using the MEGA 32 microcontroller. We wanted to make an actual product
that can produce “good-quality” percussion sounds. Our drum machine would be played via a keyboard…... Listed under:
1275. Inverted Pendulum Balancer Using Atmel Mega32 Introduction The goal of this project was to build and implement an
inverted pendulum balancer, in the vertical two dimensional plane, using Proportional-Integral-Derivative (PID) feedback
control. [caption id="attachment_16620" align="aligncenter" width="600"] Inverted Pendulum Balancer Using Atmel
Mega32[/caption] The inverted pendulum balancer is a radio controlled car…... Listed under: Game - Entertainment
Projects
1276. Vocal Trainer Using Atmel Mega32 Introduction With the Vocal Trainer, expect to resurrect your singing, and ultimately
become a vocal expert! The purpose of this Vocal Trainer, designed by Anderson Lin and Jerry Chiang, is to train people in
singing accurate pitches, and ultimately become a vocal expert. Also, the…... Listed under: Sensor - Transducer - Detector
1277. Variable Traffic Controller Introduction Our project is a Traffic Controller that is sensible to traffic condition and adjust the
traffic lights accordingly. Our project tries to simulate the traffic at an intersection, and with the use of sensors (Hall Effect in
our case), we adjust the traffic of…... Listed under: Car Projects
1278. RoboDog using ATMega32 Introduction The project, Robodog?is an autonomous car that follows sound. The car can follow
almost any audible sound that human can create by using three onboard microphones. This project was possible because of
the fact that the speed of the sound is relatively slow compare…... Listed under: Game - Entertainment Projects, Robotics -
Automation Projects
1279. PC temperature control using Atmel Mega32 Abstract Our project is a standalone temperature and fan monitoring and
control unit for the PC. It uses the temperature readings to adjust fan speeds in order to regulate temperature and noise. The
system is flexible in that it can be configured to be either…... Listed under: Temperature Measurement Projects
1280. MOS 6502 Emulation on an Atmel Mega32 ECE 476 - Spring 2003Christopher Foster and Jeff Puchalski When Chris and I first
started tossing around project ideas, I sputtered out: 'Hey! Wouldn't it be cool if we could emulate a Nintendo using some
Atmel chips?' Chris replied 'Ooh, that'd be awesome, then I…... Listed under: Other Projects
1281. A Portable Battery-Powered Roguelike Video Game Using Atmel MEGA32 I. Introduction This project is a portable battery-
powered video game based on the 1984 cult classic PC game "Rogue". I designed a hardware-based roguelike video game
because I am a long-time Rogue addict and thought it would be cool to make a portable plug-and-play imitation.…... Listed
1282. Dual control RC car using Atmel Mega32 Introduction We have always liked playing with remote controlled (RC) cars, so we
decided it would be fun to modify certain aspects of it. This led us to the idea of changing the remote control so that the car
responds to different types of input.…... Listed under: Game - Entertainment Projects
1283. Digger video game using Atmel Mega32 Introduction Sound Bite We implemented a black-and-white video (TV) game
adaptation of the old DOS classic known as Digger, by Windmill Software. Summary On the Game Start screen, a choice
between a multiplayer mode and an AI mode is offered. The multiplayer mode supports three…... Listed under: Game -
1284. Digital voice recorder using Atmel Mega32 microcontroller Our project is a digital voice recorder with distortion abilities that stores multiple tracks
onto a DataFlash memory card. We programmed an Atmel Mega32 microcontroller to sample a microphone, and store the samples into an external
memory source. We give the user the option of…... Listed under: Sound - Audio Projects

1285. Digital Guitar Tuner Introduction We constructed an analog-to-digital guitar that captures an input signal and uses the
waveform zero-crossings to determine whether the note is at the correct frequency. The hope was that this frequency tuner
could be used in a home setting where each of us can…... Listed under: Sound - Audio Projects
1286. Voting Machine Using Atmel Mega32 Introduction Our project is an electronic voting system. The system allows for quick
and accurate voting electronically. The system uses a client/server architecture, which allows voters to cast ballots on the
client terminal. Each client interfaces with the server, which keeps track of the entire…... Listed under: CNC - Printing Machines
Projects, Home Automation Projects
1287. Frequency Division Multiplexing for a Multi-Sensor Wireless Telemetry System Using Atmel MEGA32L Our System acquires
several different sensor inputs, FM modulates each level by manipulating Direct Digital Synthesis increment values, transmits
the resulting signal on a commercial FM radio band, and receives and decodes the original sensor levels. Introduction The
problem of encoding multiple input signals into…... Listed under: Sensor - Transducer - Detector Projects
1288. CubeSat Diagnostics board using Mega128 Introduction Sound Byte This project is a proof of concept diagnostic & testing
board for use with the power board in the Cubesat Satellite and will be developed further to become a component of the
CUSat Satellite. Summary of What We Did and Why This…... Listed under: Radio Projects
1289. Gauntlet of uComputation using Atmel Mega32 Introduction The project involves an experiment in implementing a human-
computer interface by tracking finger and wrist motions. Brief: "Ever wish you could control a computer just by moving your
fingers or your hand?" We did. The primary goal is to design and build a functional…... Listed under: Sensor - Transducer -
Detector Projects
1290. Laser Communications System Using ATMega32 Introduction Laser communications systems are wireless connections
through the atmosphere. They work similarly to fiber optic links, except the beam is transmitted through free space. While
the transmitter and receiver must require line-of-sight conditions, they have the benefit of eliminating the need for broadcast
rights…... Listed under: Internet - Ethernet - LAN Projects
1291. Digital Mirror Message Machine Introduction For our final project, we decided to build a digital message machine which
displayed on a mirror. This is a variation from other digital message machines we had seen in stores and in past final
projects. Instead of quickly moving a wand of LED's…... Listed under: LED Projects
1292. Memory Video Game Using Atmel Mega32 Introduction The main goal of this project was to write and develop a graphical
version of the card game commonly referred to as Memory for use on an Atmel Mega32 microcontroller unit. Memory is a
card game where the player tries to match pairs of…... Listed under: Game - Entertainment Projects
1293. TREASURE HUNT OF THE HIGH SEAS ATMEL MEGA32 INTRODUCTION Sail the high seas searching for treasure and
protecting your ship from pirates in a video game in which a system of lasers discerns the direction of wind and you specify
wind magnitude, sail height, and rudder position. Originally, we had the idea of…... Listed under: Game - Entertainment
Projects
1294. PacMan Video Game Using Atmel AT90S8515 microcontroller Introduction The goal of our project was to replicate the great
arcade classic Pac-Man on television in black and white. The inspiration for this project came from our love of video games
and our introduction to NTSC TV signal generation in Labs 3 and 4.…... Listed under: Game - Entertainment Projects

1295. SpaceInvaders Video Game Using Mega32 Introduction Our final project is the classic Atari version of spaceinvaders on the
MEGA32. The story: A horde of space invaders are attempting to land on the planet’s surface. You play a heroic pixilated
thing on the ground trying to stop them one bullet at…... Listed under: Game - Entertainment Projects
1296. Space Fighter Video Game Using ATMega32 Introduction Our project is a fighter game. The user controls a fighter, which
moves around the TV screen. The user starts the game with a defined number of lives. It has two kinds of enemies: the
asteroids and the monsters. Asteroids drop randomly from the…... Listed under: Game - Entertainment Projects
1297. Frogger Video Game Using Atmel Mega32 Introduction Sound Bite One word: FROGGER!! Why Frogger? We chose Frogger
for several reasons. First, we believe that it is an entertaining game, which is complex enough to implement as a project.
Second, Frogger allows us to use knowledge that we have acquired in this…... Listed under: Game - Entertainment Projects
1298. MIDI synthesizer Using Atmega32 Introduction: MIDI Synthesizer Our Final Project for ECE 476 was building a MIDI
synthesizer using a MEGA 32 microcontroller. At first we wanted to tear apart an old keyboard and use the MCU to decode
directly from the sensors which detected key presses. We then…... Listed under: Development Board - Kits Projects
1299. Radio Control Car using Mega32 Introduction: We like car and we like to build our own Atmel Mega32 MCU based radio-
controlled NSX. We set three goals in the initial project proposal and they are as the following: (1) Build a RC NSX with the
same performance as the original car.…... Listed under: Car Projects
1300. Sound Effects Processor Using Mega32 Introduction As you can see from the title, our project, in a nutshell, is a Sound Effects
Processor (for the lack of a better name), which is capable of taking an audio input, adding effects to it digitally and passing
an analog output to an…... Listed under: Sound - Audio Projects
1301. BattleShip Game using Atmel Mega32 Introduction : For our final project, we decided to create the classic game of Battleship
that was displayed on a TV and controlled by keypad inputs. We both enjoyed playing the board game when we were young
and we occasionally would do battle against each…... Listed under: Game - Entertainment Projects
1302. Wireless Keyboard Using Atmega32 Introduction: For our project, we designed a wireless keyboard that uses RF to transmit
signals to the computer. In our design, we use a regular, 102 key ps/2 keyboard and connect it to our transmitter circuit. On
the computers side, we connect our receiver circuit…... Listed under: Internet - Ethernet - LAN Projects
1303. TV Minesweeper Using Atmel MEGA 32 Introduction For our final project, we have decided to build a minesweeper game
with a microcontroller and a PS/2 mouse to be displayed on the TV. Minesweeper is a famous game that comes with the MS-
Windows operating system, and the objective of the game is…... Listed under: Game - Entertainment Projects
1304. Vehicle Performance Meter Using Atmel Mega32 INTRODUCTION The DomMeter is a car performance meter that measures
acceleration to compute values important to car enthusiasts. Specifically, the DomMeter calculates the 0-60mph time, 0-
30mph time, 0-100mph time, quater mile, eighth mile time and braking time, the max acceleration during that interval,
distance travelled…... Listed under: Metering - Instrument Projects, Temperature Measurement Projects
1305. Tetris Video Game Introduction For our 2003 ECE476 Design Project, we designed a Tetris game that was playable via a 16
button keypad and was displayed on a black and white television at a resolution of 128x100. The heart of the hardware
system consists of the ATMEL Mega32…... Listed under: Game - Entertainment Projects
1306. Cornell Hockey Using Atmel Mega32 News April 27, 2003 The project is due for us tomorrow, since we have the Monday
evening lab slot. We spent a little time in the lab fixing the last few bugs, tweaking a little, and taking some pictures. We have
an enclosure for the…... Listed under: Game - Entertainment Projects

1307. Gray-scale Graphics: Dueling Ships A 4-bit gray-scale video system demonstrated by a multiplayer game Our project displays
a 128-by-96-pixel image in 4-bit gray-scale (16 intensities) by using a memory-map compression scheme. The equivalent
uncompressed display would require 6-KB of memory (128 � 96 pixels � 4 bits/pixel = 6,144…... Listed under: Game -
1308. Laser Light Show Using Atmega32 Introduction Single sentence summary A programmable laser light show that allows the
user to specify the pattern displayed via three motor speeds and the length of time that this pattern is held. Project Summary
For this project, we designed a system to guide a laser…... Listed under: Sensor - Transducer - Detector Projects
1309. Wireless Drawing Device Using Atmel Mega163 Introduction: For our final project, we want to build a wireless drawing
device. The user uses a keypad or a mouse to draw on the TV through a wireless communication medium (RF - 433.92 MHz).
The user should be able to move the drawing pointer…... Listed under: Internet - Ethernet - LAN Projects
1310. IntelliBOT Using Mega 32 Introduction For our final project we decided to build a robot that could navigate from one
location to any given target and avoid obstacles in its way. The robot body used a very primitive design that included a
cardboard box for the body and Minute…... Listed under: Robotics - Automation Projects
1311. Sheet Music Generator using Mega32 Microcontroller Introduction If you are a music buff, then our sheet music generator
will be the answer to your dreams. You plug in the instrument of your choice and as you play the keys our system will create
the sheet music that attests to your musical…... Listed under: Sound - Audio Projects
1312. Multi-Zone Fire Alarm System Using Mega32 Microprocessor Introduction We designed a multi-zone fire alarm system with a
VT100-compatible user interface. The system is microprocessor controlled using the Mega32 microprocessor. The system
communicates to the VT100-compatible user interface via a RS232 connection. A fire is detectable by a number of fire
detection devices…... Listed under: Security - Safety Projects
1313. PC-CONTROLLED SCANNING TUNNELING MICROSCOPE Using ATMega163 INTRODUCTION For our final project, we
designed a scanning tunneling microscope (STM) that could be used to gather information about the surface topography of
metals and semiconductors at the sub-micron scale. The STM is controlled from a graphical user interface running on a PC.
The…... Listed under: Other Projects
1314. Tic-Tac-Toe on TV Using Atmel Mega163 Adventures in TV land The goal of this project was to play a simple game
outputted to a television via direct NTSC signal generation into a composite video input of a television. Obviously, the
outputting of material to a television is the most challenging…... Listed under: Game - Entertainment Projects
1315. Hard Drive Based AVR Programmer Using Mega163 The project which we are presenting is not the project we presented in
our proposal. We initially planned to build a WWVB time-code receiver, which would demodulate a 60 kHz signal and extract
an extremely precise time according to the National Institute of Standards and…... Listed under: Microcontroller Programmer
Projects
1316. Autonomous Car Introduction Our vehicle uses optical sensors to follow a line on the floor. Some autonomous vehicles used
in manufacturing use a similar concept. Following magnetic strips embedded in the factory floor. The versatility of an optical
design should be readily apparent. Since re-routing the vehicle…... Listed under: Car Projects
1317. Safety-sensor vehicle using Mega163 Introduction cars and vehicles have been integrated into society as one of the most
efficient, easiest, accessible means of transportation available. But while it is a convenient and common means of
transportation, it is also an incredibly dangerous mode of transport. Thousands of people die…... Listed under: Car Projects
1318. MP3 Player Using Atmel Mega103L Introduction Using MPEG Layer-3 compression, 40 MByte audio files have been
compressed to approximately 3.5 MBytes. With the wide availability of MP3 files via the Internet, portable MP3 players have
become increasingly popular. MP3 players are currently available that utilize either Compact Discs, SmartMedia, Compact…...
Listed under: Sound - Audio Projects
1319. Digital Music Synthesizer Using Atmel 90s8515 chip Introduction: Our ECE 476 Spring 2002 final project is a musical
synthesizer that mimics the sounds produced by a piano and a clarinet. We wanted to create a device that could produce
different musical signals by direct digital synthesis. Using Fourier analysis of the signals,…... Listed under: Sound - Audio
Projects

1320. The Rotating Globe Using Atmel Mega163 Introduction For years scientists and scholars alike have been plagued by one
common obstacle which, until now, has proven to be impossible to overcome. How do you find the country you want on a
globe? Sure, the easy answer is to just use the longitude…... Listed under: Motor Projects
1321. Spring 2002 Gmouse Using Atmel ATMEGA163 Introduction With all focus of computer technology advancement placed on
processors and memory, sometimes the most simple of components are overlooked. This is especially the case with the
mouse, a device that has changed very little since its conception by Xerox. It still retains its…... Listed under: Interfacing(USB -
1322. Laser Tag Introduction What is Snipertag? Snipertag is a variation upon the very popular ‘Lasertag’ game. In 1986, a company
called Worlds of Wonder came up with the idea for a combat game that worked around a set of commercially produced toy
laser guns and sensors. As…... Listed under: Game - Entertainment Projects
1323. Fish: Video Controller Introduction: The basis of this project is to create the game fish on the Atmel board. In the game fish,
the big fish eat the small fish, so your job is to eat the fish smaller than you while not getting eaten by those bigger…... Listed
under: Game - Entertainment Projects, Video - Camera - Imaging Projects
1324. Fertilizer Feed Rate Controller Abstract For a final project for EE 476 at Cornell University under the instruction of Bruce Land I
designed and built a fertilizer flow rate control unit tailored to the needs of Lin Davidson. Instead of conventional mechanical
drive methods, the delivery rate was controlled…... Listed under: Home Automation Projects, Motor Projects
1325. gEECShip Introduction Sound byte For our final project, we are redesigning the classic battleship game to suit the needs of
engineers. We are removing the need for communication, but keeping the feel of battleship. So what are we really doing?
Instead of having engineers mumble battleship…... Listed under: Game - Entertainment Projects
1326. Final Project EKG Monitoring System Introduction Unexpected cardiac death, also known as sudden death is a frequently fatal
form of arrhythmia which kills more than a quarter of a million people each year in the United States. Confronted with the
devastating effects of unexpected cardiac death and with the pursuit…... Listed under: Medical - Health based Projects
1327. Larry Pellach and Brian Silverstein Introduction Imagine being able to monitor the status of a given room or area from
anywhere in the world, at anytime. In today�s booming technological atmosphere, this dream doesn�t sound so far off.
However, imagine being able to do this cheaply, while not sacrificing efficiency…... Listed under: Temperature Measurement
Projects
1328. Analog Modem Design Project Introduction: We thought it would be interesting to try and construct a simple modem out of
the ATMEL 8535. The main motivation for doing this was to test some DSP theories about the effects of transmission power,
noise, and modulation technique on the bit error…... Listed under: Phone Projects
1329. Security Entrance System Overview: Our security system is a stand alone device that allows access to registered users
identified by their magnetic cards.(For this project, "access" is represented by a lit LED, showing how the system could be
used to control an external locking mechanism.)The system includes features…... Listed under: Security - Safety Projects
1330. EE476 – Final Project Hummer RC Truck Introduction: For our final project, we decided to enhance the controls of a Hummer
RC truck. Our main objective was to demonstrate that an Atmel microcontroller together with basic hardware building blocks
can replace all of the car's original circuitry. Improving the RC truck's handling…... Listed under: Car Projects
1331. EE 476 Final Project Portable MP3 Player Introduction In the recent years, the MPEG Layer III (MP3) music compression format
has become an extremely popular choice for digital audio compression. Its high compression ratio, and near CD quality
sound make it a logical choice for storing and distributing music - especially over…... Listed under: Sound - Audio Projects
1332. Autonomous Vehicle INTRODUCTION As technology develops, computers are making people's lives progressively easier and safer. Someday they will
be able to drive automobiles, resulting in reduced deaths and accidents. We decided to make a prototype of a self controlled car. We started with a

Hot Shot II…... Listed under: Car Projects, Radio Projects
1333. Design of a REE476 Final Project: eal-Time Digital Guitar Tuner Introduction The goal of this project is to design an algorithm
for a real-time digital guitar tuner and implement it using an Atmel AT90S8535 microcontroller. Each of the six strings of a
guitar has a unique fundamental frequency, and our goal is to measure this…... Listed under: Microcontroller Programmer
1334. Whack-A-Cap: miniature representation of a popular amusement game Introduction: Our final project code calls for the
implementation of an amusement game often bannered as "Test-Your-Strength" or less accurately (but more commonly)
known as "Whack-a-Mole." Our machine is in essence a miniturized version of what can be found in most theme parks across
the…... Listed under: Game - Entertainment Projects
1335. CU Organizer Introduction: One of the newest and fastest growing additions to the digital age in the 1990s has been the
handheld personal computer. Given a little flash memory and a good LCD, anything is possible and commercial products like
the 3Com PalmPilot� and IBM Workpad� are…... Listed under: LCD Projects
1336. Automatic Etch-A-Sketch Controller Introduction For our final project, we set out to write a Controller for the classic toy, the
Etch-A-Sketch. What this basically means, is that we use an Atmel micro controller to control two stepper motors connected
to the knobs of the Etch-A-Sketch. Thus, an order…... Listed under: Microcontroller Programmer Projects
1337. EE476 Final Project Real-time Debugger By Emre Tezel & Cagdas Ozgenc Objective: To design a debugger that is capable of
tracing AT90S1200 user programs while the micro-controller is attached to external peripherals. The debugger will be able to
display I/O activities, and dump the values of the registers. Parts Required: Atmel STK-200 starter kit (kit includes…... Listed
under: Microcontroller Programmer Projects
1338. Clifford Systems JI1000 Car Alarm System Introduction The design philosophy behind the JI1000 is a simple, yet powerful
microcontroller based mobile security system. At the heart of the JI1000 is the Atmel AT90S4414 8-bit RISC microcontroller.
We used the 4414 for this design because a microcontroller is well-suited for a security…... Listed under: Car Projects, Security
- Safety Projects
1339. Eye Snake Soundbyte If you ever thought you couldn�t control things with your eyes, think again � here�s the game Snake
that allows 4 modes of multi-level game play with buttons or with your eyes, using electro-ocular potential. Project Summary
While brainstorming for a 476 final project…... Listed under: Game - Entertainment Projects
1340. Hangman! Introduction For our final project, we used an Atmel AT90S8535 microprocessor to create a hangman game. The
letters are displayed on a 16-character LCD, and are input ("guessed") using a 16-button keypad. The 8 LED's on the Atmel
development board are used as our "hanging…... Listed under: Game - Entertainment Projects
1341. Programming the Game Simon Introduction Many of the simpler electronic games of the past decade can be easily
programmed on the AVR microcontrollers we are using this semester, using only the lights and switches available on the
evaluation boards. For our final project we programmed the game Simon using…... Listed under: Game - Entertainment
Projects

1342. A m -Controller Based Thermostat Using Atmel AT90S8535 microcontroller Introduction The goal of our final project was to
design a thermostat using an Atmel AT90S8535 microcontroller. The thermostat was to compute the current temperature
once per second and then send an on/off signal to a heating device which would then regulate the temperature to…... Listed
under: Temperature Measurement Projects
1343. Bar Inventory System: Drinking for Class Instead of Because of Class Introduction Project Summary Our project is an
expandable bar inventory system that implements wireless communication. The bar inventory system was an interesting
project, because it involved both hardware and software together, since we are comprised of one analog designer and one
computer programmer, both of…... Listed under: Arduino Programmer Projects
1344. RC Car Controller Using Atmel 4414 chip Overview: We decided to build transmitter and receiver modules for a radio-
controlled (RC) car, as well as implement variable-speed motor control and a continuous steering function. The simple speed
controls included in most RC kits seldom offer more than three forward speeds and one reverse…... Listed under: Car Projects
1345. Sine Wave Synthesizer Introduction Every group wants their final project to be something that will be remembered long after
they're gone. Some do highly sophisticated and complex projects that entail upwards of a hundred hours to complete. Yet
others go out of their way to develop something 'cool'…... Listed under: Sound - Audio Projects
1346. Temperature and Pressure Control using the AT90S8535 Overview: This project involves the implementation of control and
monitor for dual processes. The variables monitored are pressure and temperature. The input control is a 16 button keypad
and the output is monitored in a 16 character LCD The device can be widely deployed as…... Listed under: Temperature
1347. Automated Juice Mixer Introduction Sound Bite The Automated Juice mixer is a juice mixing device that allows user to create
desired drinks with up to four different ingredients through a user friendly interface. Summary Mixing juices can be a very
tedious job. We have created a juice mixer…... Listed under: Home Automation Projects
1348. Leonardo Arduino clone a single-sided PCB using ATmega32U4 DESCRIPTION This project is to make a clone of Arduino
Leonardo in a simple way.That is why the distribution of the pin does not match the standard Arduino (have to make many
jumpers on the motherboard or use both sides). However, most Arduino Leonardo characteristics are…... Listed under: AVR
ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1349. Head-Controlled Keyboard And Mouse using ATmega32 Easy Input is a head-controlled keyboard and mouse input device
for disabled users. The system uses accelerometers to detect the user's head tilt in order to direct mouse movement on the
monitor. The clicking of the mouse is activated by the user's eye blinking through…... Listed under: AVR ATmega Projects,
Interfacing(USB - RS232 - I2c -ISP) Projects, Sensor - Transducer - Detector Projects
1350. How to drive 595 shift registers with ATmega168 Driving a shift register using an AVR chip’s built-in hardware is really quite
easy. Most of their offerings have an SPI module, or Serial Peripheral Interface. A shift register is exactly that, a peripheral
device that communicates via a serial line. All we need to…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c
-ISP) Projects
1351. HexiLogger, an Arduino based data logger using ATmega328 The purpose of this project was to create a simple, portable
device that would periodically read sensors and then store the sensor data so it could be retrieved later. The result is the
HexiLogger, "hexi" because it can support up to six different sensor inputs…... Listed under: AVR ATmega Projects,
1352. Enhancing An FM Transmitter’s Firmware using ATmega48 This hack is about rewriting the firmware of PLL FM transmitters
based on AVR microcontrollers to add more functionalities. They're commonly available on eBay from various sellers and for
prices ranging from $40 to $80, depending mostly on the RF output power. If you don't…... Listed under: AVR ATmega
Projects, Radio Projects
1353. 4-key keyboard using ATtiny85 Introduction: A good while back, I made the 1-key-keyboard project. Ever since it has always been in the back of my
mind that the ATTiny microcontroller, which I used in this project, had still 3 IO ports which were unused. Only recently I’ve found the…... Listed under:
AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects

1354. RSS Reader using ATmega8 microcontroller I spent part of an afternoon developing a hardware RSS reader (most of my time
was spent on the python side of things). It’s pretty simple and uses an AVR microcontroller connected to a computer via a
serial cable. Hardware I am using the Dragon…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects, LCD Projects
1355. Virtual Archery using ATmega1284P Introduction We decided to create a virtual archery game for our ECE 4760 final project.
This game consists of an ATmega1284P microcontroller, a TV for display, and multiple pieces of hardware. All of these devices
communicate together to simulate a three-round game of archery with…... Listed under: AVR ATmega Projects, Game -
1356. Arduino – Modifying a Robot Arm using ATmega328 Essentially another tutorial involving controlling DC motors. In this post
I’m going to first alter a robot arm I had built previously from a beginners kit so that it can be controlled from Arduino. Then
I’m going to write a series of posts on different…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects, Robotics - Automation Projects
1357. Honey I Shrunk The Arduino using ATmega328p As you might be able to tell from recent posts, I've been doing quite a bit of
work with an Arduino. I've now got at least one project that I'd like to make a little more permanent, rather than it just being
a bunch of…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1358. DIY Polygraph Mask using ATmega32 Introduction A polygraph (often and incorrectly called a 'lie detector') is a machine
which plots in real time several human biological signals such as pulse rate, galvanic skin resistance (GSR), blood pressure,
and breathing rate. This machine, in conjunction with a certified examiner, is then…... Listed under: AVR ATmega Projects, How
To - DIY - Projects
1359. USB Sensors with ATtiny Microcontrollers Working with embedded electronics, you will eventually ends up with some sensor
between your hands, here I’ll show how to make a graph out of it! This project involves a light sensor, a tiny 8-pin AVR USB
key with the V-USB stack, a GNU/Linux system…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects, Sensor - Transducer - Detector Projects
1360. An electronic dice using ATmega8 Abstract: Travel to outer space sounds very exciting but now we are here in our space ship
and we have about 10 square meters for 5 people. It will take another week until we reach the first space station. I took my
mp3 player with…... Listed under: AVR ATmega Projects, Other Projects
1361. Algorithmic 8-bit workshop using ATMega328 I was asked to give a workshop regarding sound art in Super Public Art School
that is held at Titanik-gallery in Turku. As I have been working lately with microcontroller based sound synthesis I searched
for a good topic around this area. So the idea…... Listed under: AVR ATmega Projects, Other Projects
1362. Watch controlled robot using AVR microcontroller Here is my Chronos watch controlled rover. The rover has a CC1110 minikit
that receives SimpliciTI messages from the watch and sends this to an Arduino (AVR) over serial. The Arduino controls the
motors and the servo controlling the robot arm. I have called this…... Listed under: AVR ATmega Projects, Robotics -
Automation Projects
1363. Solar Power / Panel Inverter – Grid-Intertie Inverter using Attiny45 For the last year I've been working on a prototype for a
Solar Inverter that can be Grid Intertied. A solar inverter takes the 12V DC (or other voltages) from the solar panels and
converts it to 120V AC which is the power that most…... Listed under: AVR ATmega Projects, Battery Projects
1364. DigiThermo 0-100.0 °C using AT89C4051 Introduction The DigiThermo is a device designed for measuring time and temperature used in chemistry
laboratory. The circuit of Digithermo employs a 89C4051, 20-pin CMOS Microcontroller with built-in 4kB code memory. Temperature was measured by

LM35D, National Semiconductor Temperature sensor producing 10mV/°C. The CA3162, 3-digit…... Listed under: AVR ATmega
1365. Clock ControllerV1.1 using AT89C2051 Builda digital clock that turns AC load on/off with preset time. sourcecode with sdcc
for 8051. The Clock Controller V1.1was designed to be an exemplary of using 'C' language to control timer0interrupt, 7-
segment LED and keypad scanning. It provides 1-bit sink currentdriving output, for driving a…... Listed under: AVR ATmega
Projects, Clock Projects
1366. Night Light Saver V5.0 using AT89C2051 Introduction The Saver V5.0 runs simple clock emulation program, turns a night light
on and off with preset time, say 19:00 to 22:00 everyday. The design features low cost, easy installation, no battery backup
and no EMI. The AT89C2051 uses external oscillator generated by schmitt…... Listed under: AVR ATmega Projects, Home
Automation Projects
1367. Experimenting the 2051 withC Programming using 89C2051 Learn yourself, how to write a simple program using Clanguage
for the 89C2051/89C4051. Write a C source program, compile,and download the HEX code to the chip directly, connect DC
adapter, seewhat happen after power up the board. No need ICE, in-circuit programmer,everything can be made…... Listed
under: AVR ATmega Projects, Microcontroller Programmer Projects
1368. MakeYour Own Single-Side PCB for Easy-Downloader V1.1 using AT89C2051 The EasyDownloader V 1.1 , a Flash Writer for
89C2051/4051 which was designedby Wichit Sirichote, used a Double-SidePCB. I think, it's difficult to make my ownPCB by
myself. So that I decided to design a Single-SidePCB instead. My first prototype board wasmade using hand-writing with…...
Listed under: AVR ATmega Projects, Other Projects
1369. Easy-DownloaderV1.1 for ATMEL89C2051 Build your own a personal writer forprogramming HEX code into Flash based
microcontroller AT89C2051(2k) andAT89C4051(4k). Simple hardware and Easy use software in DOS and Windowversion.
Single-side and double side PCB files included.sourcecode with sdcc version! Introduction The first version of the Easy-
Downloaderwas designed in 1997…... Listed under: AVR ATmega Projects, Other Projects
1370. Easy-Downloader V1.1 with SDCC using AT89C2051 Complete schematic, orcad pcb layout of Easy-Downloader V1.1 and
modified firmware with sdcc. I am very happy to use sdcc for writing firmware of my project. The compiled code is very
compact and nice. After I succeeded writing a new firmware of xtimer and Easy-downloader…... Listed under: AVR ATmega
Projects, Other Projects
1371. AT89C2051 PROTO BOARD This single sided proto board provides an economical solution for developing and testing the
projects around Atmel 20 pin series u-controllers (89Cx051 & AVR) Figure 1 shows the circuit diagram of proto board. All
port connections are available for user interface around the proto area…... Listed under: AVR ATmega Projects, Development
1372. xTimer V1.0 using AT89C4051 microcontroller My wife asked me to find another timer for using in the kitchen. She got one
already with analog setting, but it needs one AA size battery. Digital setting may not easy for human interface. However I will
make it for easy time setting. When…... Listed under: AVR ATmega Projects, Clock Projects
1373. Night Light Saver V6 using AT89C2051 This new version has internal Ni-MH battery backup, reset button and simple time
setting. Now the circuit board was embedded with lamp fixture. Preset turn on period is from 18:00 to 22:00 everyday. You
may let the saver turn on whenever you want. The period…... Listed under: AVR ATmega Projects, Home Automation Projects
1374. AT89C4051 to work as a Real time Digital clock Its a digial clock which make use of AT89C4051 to work as a Real time clock.
Figure 1 shows the circuit diagram for the digital clock. Port 1 of the controller (AT89C4051) is used as the data lines for the
LCD (starting from pin 7-…... Listed under: AVR ATmega Projects, Clock Projects
1375. xTimer with 4094 using ATMEL89C2051 microcontroller The original version of xTimer used MAX7219 for driving 7-segment. This new design uses a
cheap CMOS shift register, 4094 for LED interface. Each 4094 drives a 0.5" 7-segment without the need of limiting resistor. The left-hand LED is timer
function with buzzer alarm output.…... Listed under: AVR ATmega Projects, Clock Projects

1376. AT89C4051 to work as a Real time clock Its a digial clock which make use of AT89C4051 to work as a Real time clock. Figure 1
shows the circuit diagram for the digital clock. Port 1 of the controller (AT89C4051) is used as the data lines for the LCD
(starting from pin 7-…... Listed under: AVR ATmega Projects, Clock Projects
1377. Mathematical Manipulation of Pure Sine Wave Inverter Using Atmel 89S2051 Introduction Approach used for creating the
pure sine wave described in this paper is done through manipulation of mathematical representation of the original sine
wave. It is done by dividing half the sine wave into m (even number) segmentations, where area under a quarter of…... Listed
under: AVR ATmega Projects, PWM Projects
1378. Testing Device for DiSEqC-Switches using ATtiny13-20PI This is my first AVR-project on this page. The DiSEqC-Tester allows to
test DiSEqC-switches that uses 1.0 or 1.1 protocols. (DiSEqC-Switches with 2.0 and 2.1 protocol have backwards compatibility
with 1.0 & 1.1 respectively and also may be tested). The device every second sends a…... Listed under: AVR ATmega Projects,
1379. Atmel AVR Infrared Downloader using ATmega8 AVR IR Downloader is one of final assignments at Electrical Engineering
Brawijaya University of Malang, Indonesia. The basic idea was came from our lecturer at campus, Ir. Nanang Sulistyanto. If
this project was successfully made, it will be used to program our automatic machine’s uC…... Listed under: AVR ATmega
Projects, Internet - Ethernet - LAN Projects
1380. Flickr images on a Nokia LCD using ATmega48 LCDs are often used in microcontroller projects. Most used are these green
character displays with two or more rows to display menus, status or debug messages. With mass production of mobile
phones, color LCDs get that cheap, that they can be used as replacement. Some…... Listed under: AVR ATmega Projects,
Interfacing(USB - RS232 - I2c -ISP) Projects, LCD Projects, Phone Projects
1381. USB AVR in-system Programmer using ATtiny2313 Introduction. Nowadays, USB is the most popular connection between PC
and peripherals such as AVR programmers, printers, scanners etc. For that reason I had to modify my old serial AVR In-
System-Programmer (ISP) to work with USB connection. You can say, "use a USB to Serial adaptor to…... Listed under: AVR
ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, Microcontroller Programmer Projects
1382. USB controlled DDS signal generator with ATmega88 A simple signal generator which produces sine waves (or any waveform
really) at audio frequencies using DDS and is controlled a USB serial connection. Only 2 chips are used in this circuit. The
AVRATmega88 which produces the signal, and an FT232R for the USB interface.…... Listed under: AVR ATmega Projects,
Internet - Ethernet - LAN Projects, Radio Projects
1383. AvrUsb500 — an open source Atmel AVR Programmer using ATmega8 Why Stk500 and USB? Until the beginning of this year
a simple parallel port programmer was the only good programmer as it could be used for any device. All device dependent
information is stored in the programmer software on your computer. The problem is however…... Listed under: AVR ATmega
Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, Microcontroller Programmer Projects
1384. HVProg using ATmega8535 microcontroller Compatible with AvrStudio Supports all AVR Controllers Parallel and serial High-
Voltage-Programming Small and easy layout with only a few parts STK500 protocol Schematics and board layout available
Introduction The project started as an enhancement of Martin Thomas Evertool project. He has rebuilt the AVRISP…... Listed
under: AVR ATmega Projects, Development Board - Kits Projects
1385. The WhereAVR using ATmega8 microcontroller Introduction The WhereAVR is a small, lightweight, low-power, and low-cost
APRS tracker with a full compliment of analog and digital I/O, as well as the ability to decode ax.25 packets. This allows for
the reception of remote commands without the need for a "real" TNC.…... Listed under: AVR ATmega Projects, Sound - Audio
Projects
1386. Video Overlay using ATmega8 microcontroller A few years ago I set about trying to design a very cheap and simple way to
superimpose flight data on live video being transmitted over amateur television. Specifically, the data would include things
like Latitude, Longitute, and Altitude, among other text including an identifier…... Listed under: AVR ATmega Projects, Video -
Camera - Imaging Projects
1387. Stealth USB CapsLocker using Tiny45 microcontroller This device plugs into a USB port and implements a USB HID keyboard.
Instead of doing anything useful, it waits between 30 seconds and 8 minutes and sends the scancode for the Caps Lock key.
This will toggle the Caps Lock status on or off.…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects

1388. etherrape using ATmega644 microcontroller Project Overview short description: microcontroller with ethernet usability status:
beta start: April 2006 platform: Atmel ATmega644 Abstract With this project, we'll be creating hard- and software for enabling
ethernet on an Atmel microcontroller. fd0 first built a prototype of it on lochraster and then made…... Listed under: AVR
ATmega Projects, Internet - Ethernet - LAN Projects
1389. AVR DDS signal generator V2.0 using ATmega16 Finally second and improved AVR DDS signal generator is here. First AVR
DDS V1.0 generator was only an attempt of running DDS algorithm without any amplitude control. This time I still wanted to
keep things simple like minimum count of widely accessible components circuit, single…... Listed under: AVR ATmega Projects,
Radio Projects
1390. Atmel AVR-firmware based universal USB-Interface using ATTiny2313 Scanning the web on microcontroller based USB
solutions, I stumbled over Objective Development's freeware USB solution based on Atmel's AVR architecture. I decided to
build up their reference design PowerSwitch with an ATTiny2313 MCU. Since I never used AVR chips before, the first
challenge was…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1391. A Portable Battery-Powered Roguelike Video Game using ATmega32 I. Introduction This project is a portable battery-
powered video game based on the 1984 cult classic PC game "Rogue". I designed a hardware-based roguelike video game
because I am a long-time Rogue addict and thought it would be cool to make a portable plug-and-play imitation.…... Listed
under: AVR ATmega Projects, Game - Entertainment Projects
1392. Evertool using ATmega16 microcontroller Evertool is an AVRISP/STK500-protocol and JTAGICE compatible Programmer/JTAG
debugger. ISP Programmer compatible with Atmel AVRISP, directly accessable with AVRStudio and avrdude JTAG debugger
compatible with Atmel JTAGICE, directly accessable with AVRStudio and AVaRice Evertool supports all AVR devices Atmel
supports with their AVRISP and JTAGICE.…... Listed under: AVR ATmega Projects, Development Board - Kits Projects,
1393. The Tuxgraphics AVR NTP clock using ATmega168 The Network Time Protocol (NTP) has revolutionized the world. Suddenly
one could have anywhere in the world accurate time and date. NTP is a simple UDP based protocol and can be implemented
in a Microcontroller. Using the tuxgraphics ethernet board and a LCD display we…... Listed under: AVR ATmega Projects, Clock
1394. Printed circuit board 'Multiuse tiny1' using ATmega8 Project overview This small PCB, which I named Multiuse tiny1 was
originally designed to convert NES/SNES controllers to USB. Since there is not a lot of space availabe inside an SNES
controller, I designed the PCB to be as small as necessary. The PCB has…... Listed under: AVR ATmega Projects, Development
1395. Cheap and Simple Learning Board using AT89S51 Build your own a cheap simple Microcontroller learning board S-52. The
board is based on ATMEL's new ISP chip AT89S51, AT89S52, or AT89S53. This board can be used by beginners for learning
Assembly and C language programming. Single sided PCB file included. Introduction I…... Listed under: AVR ATmega
Projects, Development Board - Kits Projects
1396. Sensor Interfacing using ATmega8 microcontroller If you've ever tried to hook up a 3.3V sensor to a 5V micro, you know what
I'm talking about - connecting these two can be a problem! There are several ways in which a 3.3V device can be safely
connected to a 5v microcontroller.…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, Sensor
1397. The Prototino™ using ATmega168 microcontroller What is a Prototino™? The Prototino™ is an Arduino clone with a built in
prototyping area. Designed to make a permanent version of your project once you have perfected it on a breadboard but
without the expense of embedding your original Arduino into…... Listed under: AVR ATmega Projects, Development Board -
Kits Projects
1398. How-To: Super simple serial terminal using ATMEGA128 This hack shows how to make a dumb terminal out of a keyboard,
LCD screen, and an 8-bit microcontroller. From time to time, a portable dumb terminal can be handy for when you have to
rescue a headless server that’s acting up or if you…... Listed under: AVR ATmega Projects, How To - DIY - Projects, LCD
Projects
1399. The Game of Life using ATtiny2313 microcontroller The reason for making this project is that I was always fascinated by
Conways Game of Life. It's a great demonstration of the fact that simple things with a very simple set of rules can do
wonderful things: spawn more of them, modify themselves, do…... Listed under: AVR ATmega Projects, Game - Entertainment

1400. HappyJTAG2 – JTAG AND SPI AVR8 interface using ATmega32 New version released ! V2.45 (Check version list for details) This
construction is based on HappyJTAG Idea, to implement JTAG interface into target avr system and debug it remotly via USB,
without specific JTAGICE hardware. All job is done by PC softraware. HappyJTAG version is…... Listed under: AVR ATmega
1401. Tetrapuzz – Tetris clone for AVR using ATmega168 This is a projected that I finished development on over a year ago and I’m
just now getting around to documenting it. I wanted to program Tetris from scratch and make it modular so it could be used
with different displays. Right now I know…... Listed under: AVR ATmega Projects, LCD Projects
1402. Dot Matrix Arduino Clock using ATMega168 The great adventure that is building clocks continues. Points of interest in this
build is that it was the first chance I got to play with the dot matrix display I picked up over winter break, and it's the first
time I've soldered and used…... Listed under: AVR ATmega Projects, Clock Projects
1403. ATtiny breadboard headers using ATtiny2313 These tiny controller boards are build to provide a quick start for projects with 8
and 20 pin AVR microcontrollers, e.g. ATtiny13, ATtiny45, ATtiny85 and ATtiny2313. They don’t include any fancy stuff, they
are just as simple as possible. Where is the problem? Whenever I…... Listed under: AVR ATmega Projects, Development Board
- Kits Projects
1404. Arduino-based master clock for schools using ATmega128 If your school, or kids school, or other location relies on a central
master clock that is broken, you may have a use for this device. New master clocks are available of course, but school
budgets are under extreme pressures, and it really is a…... Listed under: AVR ATmega Projects, Clock Projects
1405. FabISP, a fab-able in-system programmer using ATtiny44 The FabISP is an in-system programmer for AVR microcontrollers,
designed for production within a FabLab. That is, it allows you to program the microcontrollers on other boards you make,
using nothing but a USB cable and 6-pin IDC to 6-pin IDC cable. It's based on…... Listed under: AVR ATmega Projects,
1406. AT89LP2052 / AT89LP4052 Parallel Port Programmer Programming the AT89 LP2052/LP4052 Flash Memory, Lock Bits and
User Fuses The AT 89LP2052 / 89LP4052 microcontroller provide two interfaces with same command format for device
programming. The serial ISP Programming interface of the new 2052/4052 microcontroller needs one additional SS Signal for
device programming. This SPI signal will…... Listed under: AVR ATmega Projects, Microcontroller Programmer Projects
1407. Batwatch using ATtiny13V microcontroller Overview Batwatch is a simple monitor for a solar panel battery charger, using an
Atmel ATtiny13V. It periodically measures the charge current and battery voltage, and shows them by blinking two LEDs. I
built this circuit into the plug of a VW solar charger panel…... Listed under: AVR ATmega Projects, Battery Projects
1408. Minimalist Arduino using ATMega328P microcontroller Overview Here at the Transistor, we love the Arduino platform, so we
decided to make our own Arduino Clone. The Minimalist Arduino is designed for use in permanent or custom circuits on
solderless breadboards, stripboard, or custom PCBs. It contains only the bare minimum parts…... Listed under: AVR ATmega
Projects, Development Board - Kits Projects
1409. AVR DDS signal generator V1.0 using ATmega8 Sometimes when tuning various electronic hardware we need simple signal
generator with various waveform and frequency. One of the options is to by a professional with variable gain professional
coating and many additional functions. But if you are an amateur you might want to build…... Listed under: AVR ATmega
Projects, PWM Projects
1410. GSM Remote Control – GSM Module This GSM Mobile is used for our Remote Control (for example Gate Control,
Temperature Control….). We use the word ‘module’ because, unlike what we did in our remote control projects, this time
around the mobile phone is not mounted on a printed board, but rather on…... Listed under: AVR ATmega Projects, Phone
Projects
1411. HUB ISP – Solving the USB-Only "Chicken or Egg" Problem using ATMEGA328P Many excellent ISP (In System Programming)
designs exist for 8 bit AVR microcontrollers. However, most require a pre-programmed microcontroller, or the "Chicken or
Egg" problem: you can't program microcontrollers unless you have one already programmed. Parallel Port or Serial Port
solutions have existed, but many…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1412. Interfacing Atmel AVR with Graphics Liquid Crystal Displays using ATmega32 AVR SED1520 Library This is a C-library for avr-gcc/avr-libc to access
SED1520-based graphics-LCDs. The modules used to develop the library only support "write to LCD", read-modify- write on the display RAM is not

possible. So this Library uses a "framebuffer" which holds the display-content in…... Listed under: AVR ATmega Projects, LCD
Projects
1413. AVR Thermometer using AT90S2313 microcontroller Introduction I bought the LED module from BanMor' last week, just
30Baht. The moduleprovide a prewired multiplex of 4-digit common anode LED, that's great.See the soldering pad of these
signal in the 1st picture below. I thought,my friend gave me the AT90S2313 chip, and with…... Listed under: AVR ATmega
1414. Signal Microcontroller Simulator using AT90S8515 Introduction: The purpose of this project was to extend the Mixed Signal
AVR simulator written in Fall 02 so that any single-issue microprocessor could be included in the simulation environment
rather than limiting the simulations to systems based around ATMEL AT90S8515 series microcontrollers. In order…... Listed
under: AVR ATmega Projects, Radio Projects
1415. Air-Mouse using ATmega32 microcontroller I. Introduction The Cornell University Airmouse Initiative is a motion sensing
glove with buttons on it that plugs into your computer to function as a mouse. Many tasks that are performed on the
computer require the use of both a keyboard on the mouse, and…... Listed under: AVR ATmega Projects, Home Automation
1416. kaOS operating system and loader using ATmega32 Introduction We have created a real-time, multithreaded, preemptive
operating system called kaOS for the Atmel Mega32 microcontroller, which loads and executes programs from a Secure
Digital or MMC card.We wrote this OS and created the SD/MMC card reader as a final project for Cornell's ECE…... Listed
under: AVR ATmega Projects, RTOS - OS Projects
1417. RFID security system using ATmega32 microcontroller Introduction and Motivations: For our final project, we designed and
built (and exhaustively tested) an RFID-based proximity security system for use with Cornell Identification cards, which have
been RFID-embedded since fall of 2003. The idea for this project was sort of spawned from our general…... Listed under: AVR
ATmega Projects, RFID - NFC Projects, Security - Safety Projects
1418. The Reflow Soldering Oven with LCD Display using ATmega32 Introduction Our project consists of making a reflow soldering
device using a normal toaster oven with a graphical LCD display for control and GUI. Soldering is an important and difficult
task for custom printed circuit board design especially for integrated circuits that come as chip…... Listed under: AVR ATmega
Projects, Home Automation Projects, LCD Projects
1419. Self-powered solar data logger using ATmega32 Introduction: My project is a self-powered solar data logger. Put out in the
sunlight, it will measure the light level and log this to memory to be later downloaded to a computer. The system is powered
by a small solar panel and battery. Summary: The…... Listed under: AVR ATmega Projects, Battery Projects, Metering -
Instrument Projects
1420. Wall of Pong using ATmega32 microcontroller Wall of Pong is a fast-moving, interactive, laser-based pong game playable on
any flat surface. The system uses a digitally controlled laser projection platform to draw a pong ball onto any flat surface. This
allows for a large playing area that can be set up…... Listed under: AVR ATmega Projects, Game - Entertainment Projects
1421. A Wearable Wireless Sensor System using ATmega644V Introduction In this digital age, new interfaces for musical expression
provide much broader musical possibilities than have ever existed before. There is a constant quest to be in harmony with
one’s instrument so that music can flow freely from the imagination and take form effortlessly.…... Listed under: AVR ATmega
Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, Sensor - Transducer - Detector Projects
1422. Design a Customizable Virtual Keyboard using ATmega32 Introduction It is becoming increasingly difficult for users to
interact with the slew of portable gadgets they carry, especially in the area of text entry. Although miniature displays and
keyboards make some portable devices, such as cell phones and PDAs, amazingly small, users’ hands do…... Listed under: AVR
ATmega Projects, Sensor - Transducer - Detector Projects

1423. Adaptive Cancellation of Periodic 60 Hz Noise using ATmega32 An active noise canceler to eliminate the 60 Hz noise found in
electrical signals due to AC power-line contamination. 60 Hz noise is frustrating for anyone trying to make sensitive
measurements of low voltage processes (eg. Electrocardiogram measurements), record audio from electrical instruments (eg.
guitar…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1424. The Self-Driving Toy Car using ATmega1284 microcontroller "A car that can track its own location and calculate the direction
and distance needed to get to a final destination given by user inputs." Elevator Pitch For our final project, we built a self-
driving car that takes in inputs for a final destination and…... Listed under: AVR ATmega Projects, Game – Entertainment
Project Ideas
1425. RFID Checkout System Design using ATmega644 microcontroller The Elevator Pitch We successfully implemented a prototype
RFID checkout system that will enable consumers to instantly pay for their entire purchase upon arrival at the register,
increasing customer satisfaction, reducing retailer costs, and ultimately lowering consumer prices. Summary Shopping in the
present day usually…... Listed under: AVR ATmega Projects, RFID - NFC Projects
1426. Project Development Board using ATTiny2313 microcontroller This is my first time using the AVR. I like to learn using the
ATTiny 2313, because it is faster than MCS-51, cheap and the circuit is very simple. The chip has only 20 pins. I was interested
because I want to build a simple…... Listed under: AVR ATmega Projects, Development Board - Kits Projects
1427. Data Acquisition System using ATmega8 Introduction We can use a PC for connecting the homemade data acquisition
hardware and produce the GUI for user friendly graphical presentation easily. One of the project that uses Visual Basic is the
Data Acquisition & Logging System using AT89C51 made by Abbas Raza. In…... Listed under: AVR ATmega Projects, How To -
DIY - Projects, Temperature Measurement Projects
1428. ATMEL AVR ATMega 8535/16/32 and ATMEL AT89S5x Family Learning Kit Both Mainboard Features Pin compatible for 40-pin
AVR and AT89S5x family Microcontrollers Single sided PCB, header for 4 I/O ports, ISP port and RS-232 port Built in +5V
voltage regulator LM7805 with heatsink Built in +5V and +12V (depend on input voltage) with terminal screw…... Listed
under: AVR ATmega Projects, Development Board - Kits Projects, Home Automation Projects
1429. AVR Programmer using ATTINY2313 microcontroller INTRODUCTION AVR910 is a very useful programmer. It can program
almost complete range of AVR chips. The original version made by Klaus is here, http://www.mikrocontroller-
projekte.de/Mikrocontroller/AVR-Prog/AVR-Programmer.html. The programmer uses ISP capability of AVR chips. AVR910 first
appeared in AVR910 application note by ATMEL. It is one…... Listed under: AVR ATmega Projects, Microcontroller Programmer
Projects
1430. 4×4 keypad example using AVR-GCC C language This is as simple routine how to read 4x4 keypad keys using AVR-GCC
language. The keypad is connected to AVR microcontroller 8 bit port. In this example it is B port. You can change ports
depending on your needs – this is only an example…... Listed under: AVR ATmega Projects, How To - DIY - Projects,
1431. Servo motor control using Atmega8 microcontroller Servo motors are so called “closed feedback” systems. This means that
motor comes with control circuit, which senses if motor mechanism is in desired location and if not it continuously corrects
an error until motor reaches proper point. Servo motors are widely used in robotics,…... Listed under: AVR ATmega Projects,
Motor Projects
1432. AVR LCD menu routine using ATmega8 microcontroller Lets have some practice and write simple AVR LCD menu routine. For
this we need to write LCD control library. I decided not to use one from AVRLIB. LCD controlling isn't difficult just a few lines
of code unless you want to make it more…... Listed under: AVR ATmega Projects, LCD Projects
1433. Simplified AVR LCD routines using ATmega8 microcontroller Controlling numeric LCD isn't so tricky as it may look like. O
course you can find numbers of LCD libraries. One of more universal you can find in AVRLIB library for WinAVR AVR GCC
compiler. Main disadvantage of such universal libraries that they compile all…... Listed under: AVR ATmega Projects, LCD
Projects
1434. Measuring motor speed and display result on LCD using ATmega8 microcontroller For measuring motos speed there can
Optical interrupter used like H21A1. This is a device where IR LED and photo-transistor is coupled in to plastic housing. The

gap between then allows interrupting signal with opaque material and this way switching the output from ON to…... Listed under: AVR ATmega
Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, LCD Projects, Motor Projects
1435. AVR-GCC 4 bit and 8 bit LCD library using ATmega8 microcontroller Standard alphanumeric LCD display controlled by
74HC164 LCD controller can accept 8 bit data bytes or 4 bit nibbles. Earlier my 4 bit and 8 bit LCD libraries were split in
separate files as they were used in different projects. Now they are merged in…... Listed under: AVR ATmega Projects,
Interfacing(USB - RS232 - I2c -ISP) Projects, LCD Projects
1436. Output number when button is pressed using Atmega16 microcontroller This is simple demo program of reading button
state, lighting LEDs, sending information via USART. 8 buttons are connected to Atmega16 port A, 8 LEDs to port B via
current limiting resistors. While none of buttons arent pressed there is running light on LEDs performed,…... Listed under: AVR
1437. Simple signal drawing on graphical LCD routines using Atmega8 microcontroller During spare time I have been playing with
graphical LCD. This time I decided to display simple signals that are stored in microcontroller memory. The idea was to read
signal values from look-up table and display waveform on Graphical LCD. To make things more interesting…... Listed under:
AVR ATmega Projects, LCD Projects
1438. Programming AVR ADC module with WinAVR using Atmega8 microcontroller Most of AVR microcontrollers have Analog to
Digital Converter (ADC) integrated in to chip. Such solution makes embedded designers life much easier when creating
projects and programming them. With no need external ADC PCB takes less space, easier to create programs – it saves
time…... Listed under: AVR ATmega Projects, How To - DIY - Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, Sensor -
1439. Running TX433 and RX433 RF modules with AVR microcontrollers using Atmega8 Sometimes in embedded design you may
want to go wireless. Might be you will want to log various readings of remotely placed sensors, or simply build a remote
control for robot or car alarm system. Radio communications between two AVR microcontrollers can be easy when…... Listed
under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, Radio Projects
1440. Temperature sensor with time and date display on graphical LCD using Atmega32 Some time ago I've build a prototyping
board with graphical LCD. It have served for various small projects and prototypes. Had a spare temperature sensor DS18B20
and decided to put simple temperature display project. GLCD board is equipped with Atmega32 microcontroller running at
16MHz. DS18B20…... Listed under: AVR ATmega Projects, LCD Projects, Sensor - Transducer - Detector Projects
1441. AVR-GCC LCD library – mixed pin support using Atmega328P Some time ago we have posted alphanumeric AVR-GCC LCD
library. It works fine in 8-bit and 4-bit modes. But it has some limitations that some people may find annoying. One of them
is requirement that LCD pins has to be byte aligned for instance in…... Listed under: AVR ATmega Projects, LCD Projects
1442. Led Blink Code – Hello World Led using atmega16 in C Configuring the microcontroller before running it the first time: Fuse
bytes : high and low Program them once before you start using the micro-controller Disable JTAG to free up PORTC for
normal use Set the correct clock clock option With the hardware set up, run…... Listed under: LED Projects
1443. Remote Control based Robot using C language Concept The customer’s demands were to develop and build a kit, consisting
of a small mechatronic system with educational concept. In particular, he asked for a driverless robot for training purposes
abroad. The idea behind this is that our customer needs a kit for sending…... Listed under: Game - Entertainment Projects,
1444. On/Off Controller – Interfacing Touch LCD LC7981 using ATMega Microcontroller Concept of Touch LCD LC7981 using ATMega An on/off controller is
the simplest form of a temperature control device. The output from the device is either on or off, with no middle state. An on-off controller will switch
the output only when the temperature crosses the…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects, LCD Projects

1445. Multichannel USB Analog Sensor using ATMega48 Microcontroller Sometimes it’s tempting to re-invent the wheel to make a
device function exactly the way you want. I am re-visiting the field of homemade electrophysiology equipment, and although
I’ve already published a home made electocardiograph (ECG), I wish to revisit that project and make it much…... Listed under:
Interfacing(USB - RS232 - I2c -ISP) Projects, Sensor - Transducer - Detector Projects
1446. Door Chime Privacy Sentry using Attiny12 An ATtiny12 controller as a timer and some switching circuitry turns the doorbell
off for 10 hours at the same time each day. The string of resistors across the top of the board are series connected to make a
728 Ohm 2 watt resistor. The…... Listed under: Home Automation Projects, Security - Safety Projects
1447. DIY USB password generator using ATtiny Microcontroller Having done half a dozen V-USB tutorials I decided it’s time to
whip up something cool. As USB keyboards were an area untouched. I decided to make a small USB HID keyboard device
that types a password stored in EEPROM every time it’s attached. A…... Listed under: How To - DIY - Projects
1448. Barker Code-Locked Loop Synchronous Demodulator using ATtiny2313 microcontroller A simple, low component count
phase locked loop that locks onto and detects the amplitude of an incoming baseband 7 bit Barker code using a switched
resistor demodulator that is driven directly by a microcontroller's output pins. Balanced modulators using resistors and a
microcontroller's output…... Listed under: Other Projects
1449. Prime Calculator is Complete using ATMega8 Microcontroller My microcontroller-powered prime number
generator/calculator is virtually complete! Although I’m planning on improving the software (better menus, the addition of
sound, and implementation of a more efficient algorithm) and hardware (a better enclosure would be nice, battery/DC wall
power, and a few LEDs on the…... Listed under: Calculator Projects
1450. LED Dog Collar using ATTINY2313 Microcontroller LED Dog Collar So this is a pretty simple project, but I thought it was a
clever idea. I have 2 dogs, a lab and a lab mix. The lab "Sunshine" likes to runaway a lot if we let her outside at all. She
always…... Listed under: LED Projects
1451. Making a USB based AVR Programmer using ATMEGA8 Microcontroller Around time when I was beginning to learn about
microcontrollers. I had exchanged my laptop with a senior at college for his desktop - that's because the only way I knew
how to program an ATMEGA chip was through either a serial port or a…... Listed under: Interfacing(USB - RS232 - I2c -ISP)
Projects, Microcontroller Programmer Projects
1452. BUILD A SIMPLE SERIAL PROGRAMMER FOR AVR DEVICES using ATtiny2313 Microcontroller Atmel described a simple
programmer based on the AT90S1200 (NOT the AT90S1200A) controller in their application note. AVR910 (a modification to
use the AT90S2313 is also given below). The circuit is so small and simple. I was able to put two of them together without…...
Listed under: Microcontroller Programmer Projects
1453. LED DOT Matrix Pong using ATMega16 Microcontroller The classic pong game. Two players. Press the buttons to move
paddles up/down. Ball bounces back and forth. If you fail to catch it, your opponent gets one point. Score difference is
showed with blue LEDs. Blue LED = lead by one point. If you…... Listed under: LED Projects
1454. How to control Stepper Motor using AT89C51 Microcontroller As explained in earlier article, Stepper motor is operated by
energizing the stator coils in an ordered sequence. When the input sequence of signal is applied to the motor leads, it starts
rotating in steps. AT89C51 microcontroller has a current rating of 50mA. It can…... Listed under: How To - DIY - Projects,
Motor Projects
1455. LED Menorah using ATtiny13 microcontroller Last week on hack-a-day I saw their post on an LED Menorah that was powered
by a 9v battery with the lights controlled by dip switches. I thought to myself, “gee, that’s not a very creative design”. There
was redemption in the minimalist designs linked…... Listed under: LED Projects
1456. PS/2 to C64 Mouse Adapter using ATmega8 microcontroller A pixel artist friend of mine wanted a mouse to try his skills on a real C64. I thought I
could help him by making an adapter that would allow a regular PS/2 mouse to be used with a Commodore 64. The most popular and…... Listed

1457. MP3 Player using ATMega128 microcontroller History I decided to do this project for several reasons: Frst I like music, second
I have a huge collection of MP3, and third I wanted to be able to play them anytime in my living room. I began the project
with one major restriction.…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects, Sound - Audio Projects
1458. How to drive 595 shift registers with AVR hardware SPI using ATmega168 microcontroller Driving a shift register using an AVR
chip’s built-in hardware is really quite easy. Most of their offerings have an SPI module, or Serial Peripheral Interface. A shift
register is exactly that, a peripheral device that communicates via a serial line. All we need to…... Listed under: AVR ATmega
1459. ATtiny12 fuse restorer using microcontroller This restores the fuses in an ATtiny12 via High Voltage Serial Programming. Plug
an ATtiny12 into the 8 pin socket and hold down "GO!" button. The LED will come on at the end of the programming process,
which only takes a couple hundred millisecond. The…... Listed under: AVR ATmega Projects
1460. LED Matrix Display using TD62783 microcontroller Last Sunday I gave a workshop in TOG as part of it’s Engineers Week 2011
activities. We spent the day assembling a 8×8 Red/Green LED Matrix Display circuit which I designed in strip board. The
circuit forms an interface between a micro controller and a…... Listed under: LED Projects
1461. 3 channel, 8 bit EEPROM DAC with DS interface using ATtiny12 microcontroller Low power. EEPROM memory for autonomous
operation, 16 bytes available for general purpose use. Low cost. This device provides three channels of 8 bit pulse-width
modulation. Output pulse duty cycle ranges from 0 to 255/256 in 255 steps. DACs may be loaded by the DS…... Listed under:
1462. AvrPhone using ATmega128 microcontroller AvrPhone is a simple mobile phone with touchscreen. His brain is AVR
ATmega128 microcontroller (128 kB flash, 4 kB SRAM) and user interface, the 2.4 "LCD display with touch foil and ILI9325B
controller, equipped with a 16-bit bus. The communication with the old GSM module…... Listed under: Phone Projects
1463. Real Time Clock/Calendar/Alarm with Interpreter for battery backed-up and battery powered operation with DS interface using ATtiny12 Based on the
Atmel ATtiny12L-4PI microcontroller -A real Time Clock/Calendar for less than US$1.50 in moderate quantity. This is the
timekeeping test circuit. It includes a one-transistor circuit to switch in the 5V power supply when present and drop back to
the 3v battery the…... Listed under: Battery Projects, Clock Projects
1464. DS interface test tool using ATtiny2313 microcontroller The DS protocol was designed to provide firmware-based
bidirectional host-to-slave inter processor communications for situations in which no hardware solution is available and the
host and/or the slave in incapable of tending the interface in real time. The only specialized hardware required is two
bidirectional…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
1465. Audio Spectrum Monitor using S1D15200 microcontroller This is an evaluation use of a small graphics LCD module. Last
summer, SG12232C graphic LCD module has been sold sold for 1500 Yens from Akizuki Denshi and I bought it. However I
could not find good application for the LCD module and it was…... Listed under: Sound - Audio Projects
1466. Minimum Mass Waveform Capture using AVR microcontroller Capturing repetitive waveforms at 1 million samples per
second using PWM and a comparator. Download AVR Studio Source wfcao 030326 .asm The impetus for developing this
technique came from my own need to capture repetitive waveforms using the least expensive and lowest part-count means
possible.…... Listed under: Metering - Instrument Projects
1467. AVR mod player using ATmega325 microcontroller In 2006, I took part in an electronic demo competition on a Dutch forum
(see this topic). Because computer demos like they used to have on old machines like the Amiga or Commodore are harldy
made anymore since hardware has come such a long way,…... Listed under: Sound - Audio Projects
1468. Longboard Wheel Display using AVR microcontroller If you're a resident of Seattle, I highly recommend you check out the
Bubble events group. One of their regular events over the summer is something called "Nocturnal Push" where you can get
decked out in your best glow gear and cruise the Alki Beach…... Listed under: LED Projects
1469. AttoBasic HOME using Atmega168 microcontroller This is the central location for resource for all versions of AttoBasic for Atmel AVR controllers and
Adurino computers Devices directly supported include ATMEGA328, ATMEGA168, ATMEGA88M, ATMEGA32U4, ATMEGA32, ATMEGA163,

ATMEGA8515, ATTINY2313, AT90S8515, AND AT90S2313 Versions of AttoBasic run on several AVR controllers with 2K or…...
1470. A Superhet/Direct Conversion AM receiver for 181.818 kHz using Attiny2313 Downloads Download the AVRStudio assembly
source vlflo13041105A.asm (html format) Download the AVRStudio Hex file vlflo13041105A.hex (html format) Photo of
completed receiver. Its pocket sized, but not intended to be used that way because the antenna is a highly directional ferrite
loopstick. Its only a matter…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects, Sound - Audio Projects
1471. 1750 Meter Lowfer Band amplitude modulated RF source using ATtiny2313 microcontroller This is a low power signal source I
put together one evening to provide 187 KHz RF signals for an anticipated receiver investigation. Under Federal
Communications Commission rules inside the United States, one is allowed to operate a transmitter without a license under
certain conditions.…... Listed under: Metering - Instrument Projects
1472. Frequency Meter with 100 MHz RF desktop channel using ATtiny2313 microcontroller This basically the frequency meter
section of the frequency meter/pulse generator based on the AT90S2313 described elsewhere on this site, combined with the
100 MHz RF interface described in the page about the RS-232 to 100 MHz RF desktop channel adapter. Built and align
this…... Listed under: Metering - Instrument Projects
1473. RS-232 to 100 MHz RF desktop channel adapter using ATtiny2313 microcontroller Downloads AVR Studio assembler source
code 2jun2002version.asm AVR Studio hex file 232lin.hex This is an adapter that allows a terminal to communicate via a 100
MHz data channel with peripherals on the same desk top. Keystrokes from the terminal are are received through the RS-
232…... Listed under: Interfacing(USB - RS232 - I2c -ISP) Projects
1474. Low cost RF for simple data link and remote control using ATtiny12 microcontroller Wireless data links don't have to be
difficult to build or adjust They can be built quickly using inexpensive and readily available parts. Overview This is a simple,
low cost RF data link that can send data reliably over a distance of one to two…... Listed under: Interfacing(USB - RS232 - I2c -
ISP) Projects
1475. Minimum Mass Wireless LCD Display using ATtiny2313 microcontroller A 2 line X 16 character LCD display that is battery
operated and works without an external connection. The basic MinThe basic Minimum Mass Wireless Coupler technology is
described and links to other projects on this site that use the Minimum Mass Wireless Coupler are…... Listed under: Internet -
Ethernet - LAN Projects, LCD Projects
1476. A Low Power PLL FM Transmitter using LMX1601 and ATtiny2313 microcontroller An LMX1601 Phase locked loop, a discreet
FET VCO, and an AVR micro controller combine to make a stable, easy to use monophonic FM transmitter that includes a an
audio activated switch that turns the transmitter on only when its being used. Notice: Before operating…... Listed under: Radio
Projects
1477. A Simple FM Stereo Transmitter using ATTINY12 microcontroller The parts to the right of the green capacitor are the FM
radio transmitter. The parts between the 8 pin DIP and the transmitter are the resistor matrix. One capacitor, C5, is mounted
on the back of the board, and one other capacitor, C11, had…... Listed under: Radio Projects
1478. DIY mobile phone – Create your own mobile phone This DIY cell phone created at MIT manages to have something for just
about every major contemporary subculture or hipster subset I can think of. Nerds and tinkerers? Check. Wooden case for
the steampunk set? Check. Huge antenna for the retro, skinny-jeans-wearing set? Check. Big…... Listed under: How To - DIY -
Projects, Phone Projects
1479. Are you being spied – A Simple Field Strength Indicator (field strength meter) This project is a broadband field strength
sensing probe that has a 15cm antenna. It is able to detect radio energy and read the output on a common multimeter
millivolts scale. It can be used to test 4MHz, 35 MHz, 55 MHz, 100 MHz, 384 MHz,…... Listed under: Blog, Circuits
1480. What is a stun gun – How to Make Stun Gun What is Stun Gun An electroshock weapon is an incapacitant weapon used for
incapacitating a person by administering electric shock aimed at disrupting superficial muscle functions. One type is a
conductive energy device (CED) fires projectiles that administer the shock through a thin, flexible wire. Other electroshock
weapons such as stun guns, stun batons,…... Listed under: Blog, Circuits
1481. How a Microwave oven works? Bill details how a microwave oven heats food. He describes how the microwave vacuum tube, called a magnetron,
generates radio frequencies that cause the water in food to rotate back and forth. [caption id="attachment_8043" align="aligncenter" width="563"]
microwave interior structure[/caption] He shows the standing wave inside…... Listed under: Blog, Circuits

1482. Multifunction 330 MHz Remote Control With an ATTINY2313 Simulating the PT2264 Encoder This 330 MHz remote control
sends timed sequences of control pulses to accomplish complicated tasks. You can probably tell that I used a lot of solder
flux on this board. Lots of flux not only helps the solder wet to the copper, but it also…... Listed under: AVR ATmega Projects,
Radio Projects
1483. Circuit and firmware to support Seiko-Epson G1216B1N000 dot graphics display using ATtiny2313 A serial interface and bias
supply for the Seiko-Epson G1216N000 using an AT90S2313 because there just aren't enough applications examples for this
display on the web. Download Assembler source code I was looking for an LCD display that I could use to display waveforms
on…... Listed under: AVR ATmega Projects, LCD Projects
1484. A serial interface for the Truly MTC-C162DPLY-2N using ATmega8515 The 10k potentiometer, just above the ISP connector
near the lower middle of the board,is used to adjust the display contrast according to your vertical viewing angle.
DOWNLOADS ATTINY2313/AT90S2313 AVRStudio assembler source, LDCbutons040904Ca.htm ATTINY2313/AT90S2313
AVRStudio assembler source, UPDATED FOR COMPATIBILITY WITH NEWER VERSIONS OF THE…... Listed under: AVR ATmega
1485. Simplest LED Flasher Circuit As simple as it gets and still works This LED flasher occurred to me while reading about negative
resistance in transistors. It was reported that Leona Esaki, who was at Sony at the time, had been surprised to see a negative
resistance region while investigating…... Listed under: AVR ATmega Projects, LED Projects
1486. A 1.5 Volt, 1970’s Style LED Flashing Red Caboose Marker Light using tiny microcontroller A circuit that drives a red LED from
a 1.5 volt battery and simulates an incandescent light. Duty cycle can be changed by selecting resistor values. Photo 1. This
printed circuit board is 3 cm long. The first prototype was made with through hole parts.…... Listed under: AVR ATmega
Projects, LED Projects
1487. White LED Stroboscope Finally, white LED's are bright enough to use in a practical stroboscope. This circuit can operate as a
bench-top stroboscope that, in conjunction with an oscilloscope or frequency meter and bench top power supply can
accurately measure rotational speeds, or it can be operated hand-held…... Listed under: AVR ATmega Projects, LED Projects
1488. White LED Battery Powered Power Failure Light Overview Where I live most of the time, the AC power drops out upon
occasion. This used to leave me groping around in the dark for a flashlight. I could have bought a battery-backed up
"emergency light" for about US$35, but being basically metal boxes…... Listed under: AVR ATmega Projects, Battery Projects,
LED Projects
1489. Atmega8 Pinout Diagram ATmega8 is an atmel's low-power 8-bit AVR RISC-based microcontroller combines 8KB of
programmable flash memory, 1KB of SRAM, 512K EEPROM, and a 6 or 8 channel 10-bit A/D converter. The device supports
throughput of 16 MIPS at 16 MHz and operates between 2.7-5.5 volts. [caption id="attachment_7971"…... Listed under: Blog,
Circuits
1490. SKL14 -1A Schottky diode will fit everywhere SKL14 can be used in switch-mode power supplies or as protection diodes and
thanks their really miniature dimensions, they are also suitable at the lack of PCB space. SMT Technologies enable a
substantial increase of current density thanks to a very good heat transfer from…... Listed under: Blog, Circuits, News
1491. A White LED Night Light Design BUT FIRST AN IMPORTANT NOTE: This project uses lethal voltages. If you are not
experienced in working with lethal voltages, read this project, but don't build it. You only have one life, and AC power can
take it from you very quickly, or leave you…... Listed under: AVR ATmega Projects, Home Automation Projects, LED Projects

1492. Series Connected Voltage Boost Circuit for a Battery Operated LED Lantern Photo. This is the test circuit -the basic driver is
only two transistors, two resistors, the circuit was evaluated using a white LED, but when it was time to button it up and
archive it, I replaced the expensive white LED with a cheap green…... Listed under: AVR ATmega Projects, Battery Projects, LED
Projects
1493. FAST PRECISION LED DRIVER What it is The circuit allows a precision regulated drive current to be set to drive an LED, and in
response to a TTL level signal, the LED is switched on and off with rise and fall times of less than 500 nanoseconds and
less…... Listed under: AVR ATmega Projects, LED Projects
1494. Remote Controlled (R/C) Airplane LED Flasher using ATTINY12 microcontroller Downloads Download the AVRStudio assembly
source for the program: T12astrobe081028A Download the AVRStudio assembly source for the include file:
T12astrobe081028A.hex Find updates at www.projects.cappels.org Overview This was designed to flash a pair of LEDs to be
mounted on the wing tips of a Parkzone Citabria…... Listed under: AVR ATmega Projects, LED Projects, Radio Projects
1495. Single and Two Cell White LED Drivers Without Inductors Three inductor-free circuits that allow a white LED or UV LED to be
driven from one (1.5 volt) or two flashlight cells (3 volts total) are described. The circuits on this page are: The two cell (3 volt)
circuit four transistors. The simple single cell…... Listed under: AVR ATmega Projects, Battery Projects, LED Projects
1496. 1 Watt White LED Power Supply Circuit for battery operation Download FreePC project file, gerber and png copper and silk-
screen: 1wattledbuck.zip Introduction I have some 1 watt warm white LEDs left over from a project and the application for
them was obvious: A better battery operated lamp for use when the power fails, which it does…... Listed under: AVR ATmega
Projects, Battery Projects, LED Projects
1497. Attention-Getting Auxiliary Warning Light Flasher/Driver Overview The circuit shown in Figure 1 is capable of driving an LED
array requiring up to several amps with a burst of flashes before coming on until power is removed. It is intended to be used
as an auxiliary warning light driver. The initial…... Listed under: AVR ATmega Projects, LED Projects, Security - Safety Projects
1498. White LED Drive Circuit using Tiny microcontroller Be Careful About Peak Current A note of caution: These LEDs are
comparatively expensive, so I suggest putting a small resistor (1 to 10 Ohms) in series with the cathode of the LED and
measuring the peak current as inferred from the IR drop using…... Listed under: AVR ATmega Projects, LED Projects
1499. Low Capacitance Scope Probe Adapter An adapter to allow low capacitance probing of high frequency circuits. Overview My
boss, Dave, said "Just hold the probe close to the cathode lead." Dave had worked at Tektronix for many years, and his ability
to make difficult measurements was second only to his…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1500. AC Current Probe for Oscilloscopes Overview I needed several current probes when designing the deflection circuits and high
voltage supply for a computer display monitor, and the lab in which I was consulting only had one current probe, which I
shared with the other four engineers on the project. We…... Listed under: AVR ATmega Projects, Metering - Instrument
Projects
1501. A Portable Precision Voltage Reference using microcontroller Introduction It has been said that a man with one watch knows
what time it is, but a man with two watches is never sure. The same can be said for a person who has more than one
voltmeter. In my situation, I have several…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1502. Simple LM335 Thermometer using microcontroller Not too many parts. When a voltmeter is connected across the outside
terminals of the output connector, its display reads out in degrees C. I've been fascinated by the LM335 for some time -
maybe my obsession with stability finally gave way to my fascination with…... Listed under: AVR ATmega Projects, Metering -
Instrument Projects
1503. Minimum Mass Waveform Capture and Display using AT90S2313 microcontroller A 128 x 64 graphic LCD is in the clear plastic
box at the top. It is connected to the waveform capture and control unit in the green pencil box below the display.

Downloads AVR Studio 3.5 ASSEMBLY SOURCE for the waveform capture controller.…... Listed under: AVR ATmega Projects, Metering - Instrument
Projects
1504. Broadband RF Field Strength Probe using Atmel AT90S1200A AVR controller Download auto-zero assembly code This
broadband probe has a small antenna (about a 15 cm length of insulated wire). Radio Frequency energy coupled to the
antenna is detected and made available to drive millivolt level signals to the input of a DVM (Digital Volt Meter).…... Listed
under: AVR ATmega Projects, Radio Projects
1505. A Field Strength Meter Using A Biased Schottky Detector using microcontroller Downloads Download the Download FreePC
files in and the detector board layout png file in zipped forma: schottkydedtector080309 Find updates at
www.projects.cappels.org Starting to do a little work at 330 MHz, I decided that my existing field strength meters were not
adequate for for my…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1506. Precision Audio Frequency Peak Detecting Probe using microcontroller This is a handy companion for a digital voltmeter. Its
allowed me to do a lot of things I used to use my oscilloscope for, and in addition it measures voltages to much greater
precision.Using an LM324 quad op amp, this peak detector provides 2%…... Listed under: AVR ATmega Projects, Metering -
Instrument Projects
1507. Cellphone Operated Robot using ATmega16 AVR microcontroller This Instructible is entered in the Category: 13 - 18 of the
National Robotics Week Robot Contest MY URL-http://avadhutelectronics.blogspot.com/ MY Email-
avadhut.deshmukh@gmail.com Video :Cellphone Operated Robot Step 1 Component Required Component Required: IC1 -
MT8870 DTMF decoder IC2 - ATmega16 AVR microcontroller IC3 -…... Listed under: AVR ATmega Projects, Phone Projects,
1508. HF AC Millivoltmeter Adapter using microcontroller Encased in a pencil box to keep the point-to-point wiring on the back of
the board from shorting to wires and things on the workbench, the plastic case also holds the offset and gain post as well as
the input connector and the switches that…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1509. PHduino pH Meter Using Arduino About This project describes an open software open hardware pH meter using an
Arduino/Freeduino board. In other words, this is an electronic circuit to be connected with a glass electrode pH sensor. It was
possible by the idea from my friend Mr. Denis Vidal, the…... Listed under: AVR ATmega Projects, Metering - Instrument
Projects
1510. A Microcontroller Based Digital Lock-In Milliohmmeter using ATtiny2313 microcontroller Download: assembler source
mhm031002A.asm A milliohmmeter is just the tool for checking trace resistance on a printed circuit board, tracking down
shorted traces, and measuring the contact resistance of a switch or connector. Its the kind of tool that would come in real
handy occasionally,…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1511. Dutchtronix AVR Oscilloscope Clock using Atmega328 microcontroller Hardware features: Connects to your analog scope in
X-Y mode using BNC cables or probes (1x, 10x) Uses the Atmel AVR Atmega328p with 32KB flashmemory On board 5V
power regulator for use with user provided wall adapter (8-15V DC center positive) Power plug (5.5mm…... Listed under: AVR
ATmega Projects, Clock Projects
1512. I2C Tiny USB using ATtiny45 microcontroller Attach any I2C client chip (thermo sensors, AD converter, displays, relais driver,
...) to your PC via USB ... quick, easy and cheap! Drivers for Linux, Windows and MacOS available. The i2c-tiny-usb project is
an open source/open hardware project. The goal of i2c-tiny-usb is to…... Listed under: AVR ATmega Projects, Interfacing(USB -
1513. TRUE RMS-TO-DC Adapter For DVM using microcontroller Specifications Input: AC, DC or AC+ DC to > 10 KHz Ranges: 200
mv, 2V, 20V, 200V, 600V full scale Accuracy: ±1%, depending on divider resistor selection Crest Factor: 1 to 3, up to 5 with
degraded accuracy Input impedance: 1 Megohm shunted by 20…... Listed under: AVR ATmega Projects, Metering - Instrument
Projects
1514. MMC/SD/SDHC AVR Interface using ATMega8 microcontroller MMC/SD/SDHC card library This project provides a general
purpose library which implements read and write support for MMC, SD and SDHC memory cards. It includes low-level MMC,
SD and SDHC read/write routines partition table support a simple FAT16/FAT32 read/write implementation The circuit The
circuit which…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, Memory - Storage Projects,

1515. A Pretty Good Wattmeter For Bench Use using microcontroller Briefly, • AC True Watts using two quadrant multiplier •
Optimized for 120 VAC (can be changed) • 15 watt full scale (can be changed) • Uses DVM floating on AC Neutral as display •
Requires moderately high level of analog circuit skill • Very…... Listed under: AVR ATmega Projects, Metering - Instrument
Projects
1516. RS-232 Freq. Meter/Pulse Generator Based on Atmel ATtiny2313 using microcontroller Simplicity in circuitry was the design
direction. Zero mass (firmware only with no physical components) would the ultimate achievement. This instrument doesn't
have any front panel controls because the user interacts via an RS-232 terminal program at 9600 baud. I needed a frequency
meter for…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1517. Analog audio panel for PC using ATMega328 microcontroller Have you ever struggled with audio settings in control panel in
middle of a VoIP call? Or, wondered if the other guy can hear you properly? I have. My work requires great deal of remote
conference calls using PC. The first thing I wonder always…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1518. Preamp and 330 + MHz Prescaler for A Little More Serious Frequency Meter using microcontroller Overview After finishing
Little More Serious Frequency Meter I had planned to make a suitable preamp and prescaler for it, and set about to gather
ideas and parts. I was inspired by one fellow who had built the meter and the 2 line X16 character…... Listed under: AVR
ATmega Projects, Metering - Instrument Projects
1519. A Little More Serious Frequency Meter using ATtiny2313 microcontroller This is design for a frequency meter based on AVR
microcontrollers. Maximum input frequency is specified to be 30 MHz in the multi-chip configuration, and in single-chip
configuration, there are both 5 MHz and 10 Mhz versions operating with 10 and 20 MHz crystals, respectively.…... Listed
under: AVR ATmega Projects, Metering - Instrument Projects
1520. HF/VHF/UHF TEST OSCILLATOR using microcontroller Its built into a plastic project box with an aluminum cover (on the
bottom). The controls are as follows: Large golden knob is coarse tuning, small black knob with a blue index stripe is fine
tuning, the green LED is the power on indicator, the…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1521. RF Inductance Meter using microcontroller I needed a way to measure hand-wound RF inductors in my second lab, and since
I would only be doing this occasionally, I didn't need anything fancy, and since once a friend finishes his AT90S1200-based
design, I plan to make one myself, I figured I'd…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1522. LC Determination by Resonant Frequency Measurement using microcontroller A well known L/C measurement circuit is
pressed into service to make a bare bones measurement circuit. Download the AVRStudio assembly source: lgm031227I.asm.
Download the AVRStudio hex file: lgm031227.hex. Left-to-right: The 5 volt regulator, the LM393 oscillator (a 0.047 uf
capacitor is mounted on the…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1523. Battery Checker Circuits using microcontroller The "Battery Good" checker. When the button is pressed, the green LED will
glow if the battery voltage is above the preset threshold. This version has a higher parts count than the "Battery Low" version,
but a bonus is that it can drive an LED…... Listed under: AVR ATmega Projects, Battery Projects
1524. A 1 Khz Digital Sine Wave Signal Source using ATmega8515 microcontroller 1 Khz From a Quartz Crystal 1 V P-P Sine Wave
Calibrated Output 1 KHz Square Wave Output 900 mv Inverted Sine Wave Output (Uncalibrated) Downloads Download the
WINAVR main source for the 2313 version of the firmware: 2313sine.c. Download the complete zipped WINAVR project…...
Listed under: AVR ATmega Projects, PWM Projects
1525. A Noise Generator per IEC 268-1, IEC 268-5, and IEC 268-7 A related article on this site: True RMS-To-DC Adaptor for DVM
Introduction This project came about when I needed to perform some reliability tests on some headphones according to IEC
268-7. The test requires operating the headphones at their rated input power for a number…... Listed under: AVR ATmega
1526. MAX038-Based Sweep/Function Generator With Markers using AVR ATtiny2313 microcontroller Take Maxim's MAX038
function generator chip, add some frills, and you have a pretty nice tool for the bench. Downloads: Main Circuit Schematic

Power Supply Schematic You can build this with switches instead of buttons if you don't want to use a micro controller. Here…... Listed under: AVR
ATmega Projects, PWM Projects
1527. An Isolated Adjustable Auto transformer using microcontroller This is a means of testing AC mains operated circuits at
variable AC voltages, and it also provides isolation to allow safe measurements of that circuit. A fused isolation transformer
and a variable auto transformer connected together in a grounded, fire safe box. What…... Listed under: AVR ATmega Projects,
1528. A 10 Bit LED Digital Panel Meter With Auto Ranging Based On The ATMEGA8 Downloads Download the AVRStudio assembly
source for the program: M8DPM091109A.asm Download the AVRStudio hex file: M8DPM091109A.hex Find updates at
www.projects.cappels.org Overview - A 10 bit digital panel meter for positive voltage only. - Input resistance: about 130k -
Ranges: 0 to 10.20 volts and 0…... Listed under: AVR ATmega Projects, LED Projects, Metering - Instrument Projects
1529. Photocell Amplifier using microcontroller This is a low frequency amplifier with an adjustable transimpedance that is intended
to be used to take relative measurements of a wide range of photo currents. Not having many parts, this amplifier can be put
together in a short amount of time. Find updates…... Listed under: AVR ATmega Projects, Solar energy projects
1530. A SIMPLE MANUAL CURVE TRACER using microcontroller Measure current vs voltage or voltage vs current over limited range
with good accuracy. This was built on a phenolic board which was mounted on a plastic box. The box serves two purposes: It
holds the circuit off the workbench, and it makes a nice,…... Listed under: AVR ATmega Projects, Metering - Instrument
Projects
1531. A Pretty Good LC Meter Based on the AVR using ATTINY2313 Microcontroller Calculates and displays L and C from oscillation
frequency using reference components. No relays, no range switching, a minimum of controls. And it is pretty accurate too!
Note: After reading this article, check out the improved, modified An Even Better LC Meter... The 2 line…... Listed under: AVR
1532. An Even Better LC Meter Based on the AVR ATTINY861 An improvement over "A Pretty Good LC Meter." Enhanced
capacitance self calibration, accurate operation without precision components, and only one micro controller. Downloads
Download or view the WINAVR main source file: lcm.c Download the complete package including the LCD library: Even-
Better_LCM.zip (LCD Library provided with…... Listed under: AVR ATmega Projects
1533. GSM GPS module shield for Arduino Shield for Arduino designed and based on the module GSM/GPRS SIM900 or the
GSM/GPRS & GPS module SIM908, to make calls, voice and data connections via GPRS allow maximum customization and
provide many configurations. With a microphone and a headset with a 3.5 mm jack (just the standard…... Listed under: AVR
ATmega Projects, GPS Based Projects
1534. Interfacing DRAM Memory using AVR microcontroller Is it possible to use DRAM with microcontroller AVR? Yes, it is possible.
Jesperh has proved it. He hooked up a DRAM to a small processor (in this case an Microcontroller Atmel 8515), and handle

the RAS/CAS sequencing and refresh in software. The type of…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1535. Ponyprog Circuit for AVR & PIC16F84 using microcontroller Comments: All resistors are 1/4W.The circuit is powered by
9...15V DC or AC. When In Circuit Programming (ISP) connectors are used, is possible the programmer to be powered from
target’s power source. Diodes D2 and D6 protect the regulator LM7805, when target’s power is used.…... Listed under: AVR
ATmega Projects
1536. Ponyprog Circuit for ATMEL’S AVR using microcontroller The ATMEL AVR programmer works with the Windows program
"Ponyprog" which works under 95, 98, XP. On board the AVRs that can be programmed are those in the schematic. For other
members of AVR family or the rest programmable ICs that Ponyprog can program, there…... Listed under: AVR ATmega
Projects
1537. EPROM adapter for ATMEL 89 Series Flash Microcontroller Programmer Devices The EEprom programmer software supports
the following devices. 28C16 28C256 28C17 29C256 28C64. Hardware Diode D1 and resistor R1 provide the VDD isolation
when programming the 24 pin devices. The jumper J3 must be shorted for 24 pin devices, and open circuit for 28…... Listed
1538. PCB Exposure Box with Countdown timer using ATMEGA8 microcontroller Tired of spending hours and hours in wire
soldering? Do your circuits look ugly and you are looking for a way to produce professional-like PCBs? Then you had better
try photoetching. And the first step to do that is to have the right equipment that…... Listed under: AVR ATmega Projects,
Other Projects
1539. 89Sxx Development Board using microcontroller Introduction of 89Sxx There are some 89Sxx development board, here is
another one. I have designed this single side development board to be used as a tool for learning MCS-51 Microcontrollers,
and for easy microcontroller project development. The 89Sxx development board features : 89Sxx 40-DIL based…... Listed
under: AVR ATmega Projects, Development Board - Kits Projects
1540. Wireless Coupler Terminal Interface using AVR microcontroller This is a Minimum Mass Wireless Coupler that connects a
terminal, or PC running terminal software, to other Minimum Masss Wireless devices by means of a 1200 baud data channel
at 181.818 kHz. The basic Minimum Mass Wireless Coupler technology is described and links to…... Listed under: AVR ATmega
Projects
1541. RF Field Strength meter using AVR microcontroller The hot melt glue that covers the circuit serves multiple purposes: It helps
to keep the temperature even among the three transistors (to minimize thermal drift), it protects the components from
physical damage, and it holds the battery holder on the board. As I used…... Listed under: AVR ATmega Projects, Metering -
Instrument Projects
1542. Digital Telemetry using ATMega8 microcontroller The ATmega8 microcontroller-based Low-Cost Telemetry Device (LTD) is an
efficient telemetry keyer. The LTD measures the voltage levels of up to four analog channels via its on-chip 10-bit ADC,
converts the measurements to numbers, and then sends the data in Morse code to an external…... Listed under: AVR ATmega
Projects, Metering - Instrument Projects
1543. LC Resonant Frequency Meter using AVR microcontroller A well known L/C measurement circuit is pressed into service to
make a bare bones measurement circuit. Download the AVRStudio assembly source: lgm031227I.asm Download the
AVRStudio hex file: lgm031227.hex Left-to-right: The 5 volt regulator, the LM393 oscillator (a 0.047 uf capacitor is mounted
on the…... Listed under: AVR ATmega Projects
1544. AVR LED RF Field Strength using microcontroller Useful as a transmitter tune-up meter or an RF sniffer, this is an RF field
strength indicator that is loosely based on the Broad Band RF Field Strength Probe, described elsewhere. It detects RF via a
square law detector, basically its a crystal set with…... Listed under: AVR ATmega Projects
1545. Control Relay Card with USB port Atmel using Atmega8 microcontroller Once upon a time, though a circuit of this type of
calling Searches Banim made with Microchip PIC Series devreydi 6 pcs rörele control pcb computer program code can be
done via usb port usb drive and 9-12 volts AC regulated power supply section of…... Listed under: AVR ATmega Projects
1546. Temperature Sensor Thermometer using AT89C51 and DS1621 microcontroller DS1621 temperature sensor circuit digital thermometer to tell if
using. Operation of the circuit is simple, as are as follows: temperature sensor from the numeric value being sent to the microcontroller and the

microcontroller using the I2C serial communication protocol, this value will more basıyor.Biraz If the LCD
tomicrocontroller interprets…... Listed under: AVR ATmega Projects, Sensor - Transducer - Detector Projects, Temperature
1547. About Atmel and Combination Lock Application using AT90S2313 microcontroller Microcontroller Microcontroller 's (MCU) is
a kind of CPU (CPU) can be seen as. MIB MCUs from slower and less capable of addressing memory, but they are designed
for the implementation of real-time control problems both cheaper and easier to use. The major difference between CPU
and…... Listed under: AVR ATmega Projects, Security - Safety Projects
1548. Led Animation Circuit with PC Connectivity using AT90S2313 microcontroller Animator is a device, rather 5 × 16 matrix LED ,
which are used to display simple animation. Initially, the device serves to something completely different and it was
controlled directly from the parallel port for the program is written in Pascal. The idea has proved to be a…... Listed under:
AVR ATmega Projects
1549. Color Sensor Circuit with AT89S52 ADC0808 This color of the surface color to red when you bring to the surface, a sensor to
read the LDR, yellow, blue.Red, yellow and blue lights in different surface finishes as a different yansıtmalarını works by taking
a foothold. Will be reflected from the surface to…... Listed under: AVR ATmega Projects, Sensor - Transducer - Detector
Projects
1550. Serial interface with 2X16 LCD display using ATMega8515 microcontroller The 10k potentiometer, just above the ISP
connector near the lower middle of the board, is used to adjust the display contrast according to your vertical viewing angle.
DOWNLOADS ATTINY2313/AT90S2313 AVRStudio assembler source. LDCbutons040904Ca.htm ATTINY2313/AT90S2313
AVRStudio assembler source. UPDATED FOR COMPATIBILITY WITH NEWER VERSIONS OF…... Listed under: AVR ATmega
1551. G1216B1N000 dot graphics display using AT90S2313 microcontroller Download Assembler source code I was looking for an
LCD display that I could use to display waveforms on the workbench. The selection criteria for the display module itself was
straight forward: 1. Dot graphic with sufficient resolution to display a simple waveform, 2. Available…... Listed under: AVR
ATmega Projects
1552. LCD Date Time Application using AT89S52 microcontroller This application can be installed at the same time an alarm
indicating the date and time produced by Atmel with 8051 -based microcontroller AT89S52 tasarlanmıştır. Uygulamamızın
using the Keil compiler using the C programming language using codes written in different types of intervention. Proteus
simulation…... Listed under: AVR ATmega Projects
1553. Dot Matrix Display Applications using AT89C2051 microcontroller 4 Piece AT89C2051 micro-controller matrix display has a
project carried out with proteus isis simulation and has asm hex code files Atmel AT89C2051 • Compatible with MCS
®-51Products • 2K Bytes of reprogrammable Flash Memory - Endurance: 10,000 Write / Erase Cycles • 2.7V to 6V
Operating…... Listed under: AVR ATmega Projects, Other Projects
1554. 100 MHz RF oscillator using ATtiny12 microcontroller I needed a frequency reference for tuning up the RS-232 to 100 MHz
RF desktop channel adapter elsewhere on this site, when I found this Saronix crystal oscillator in my junk box. A few minutes
with AVRStudio produced an ATtiny12 to make a tone -…... Listed under: AVR ATmega Projects
1555. Atmel Test Card using ATmega32 microcontroller PCB and the schema (sch) P-CAD 2004 Schematic drawings prepared by
V18.00.2690 also c languagecode through the test has been prepared with an alternative link. ATMEGA-32 Development
Board Power 7V to 12V (4mm sockets) protected against reverse polarity Visualization by 8 LEDs Statements of eight…...
1556. Computer connected Flower Water Circuit using ATmega8 microcontroller Interestingly, I understand a project is determined
by the required hours of irrigation irrigation data via a computer data exchange rs232 com port are made out of a project
source code and is not easily implemented scheme, For more detail: Computer connected Flower Water Circuit using…...
1557. Multimeter with Atmel using Atmega8-16pu microcontroller Atmega8 Multimeter "Multimeter" was the only title to einfiel to
me first. Voltmeter (only positive DC) 0.00 - 9.99 volts and 10.0 - 30.0 volts with automatic range switching. Frequency
counter 0 .. 7999 MHz (Theoretische) with automatic Switching time Basis Logic tester L - prohibited area…... Listed under:
AVR ATmega Projects

1558. Decoding 4 buttons with two I/O’s on AVR using ATtiny12 microcontroller Just the solution for AVR applications in which I/O
is tight, such as the ATtiny12. This should work well on other kids of controllers that have independently controlled I/O
direction registers, such as PIC and 6805 controllers. This is a solution was devised for those…... Listed under: AVR ATmega
Projects
1559. EEPROM Driver for AVR with RAM using ATtiny15 microcontroller Download the test program with driver: i2cm030710F.asmI had been putting off
writing a driver for some 24LC64 and 24LC256 EEPROMS I was thinking about using, when I came across a temperature logger application written by
Sean Ellis. The Temperature logger was posted on on www.avrfreaks.net…... Listed under: AVR ATmega Projects, Other Projects
1560. Analog Multiplexer using AVR microcontroller This technique uses digital I/O pins to multiplex analog voltages into an
analog input on the microcontroller. The method is most suitable for signals that do not need to be sampled frequently and
it may be extended to accommodate a large number of inputs, though…... Listed under: AVR ATmega Projects
1561. PWM Waveform Capture using AVR microcontroller Described are the waveform capture method, example firmware and
hardware designs. This material formed the basis of an article that was first published in the October, 2003 issue of Circuit
Cellar magazine. The only components added to the operating Atmel AT90S2313 circuit (one capacitor and two…... Listed
under: AVR ATmega Projects, PWM Projects
1562. 1 KHz Synchronous Detector using AVR microcontroller Downloads: Assembler source deco030511C.asm AVR Studio hex file
is deco030511C.hex Overview This circuit employs a synchronous demodulator to separate a 1 KHz signal from noise and
measures the amplitude of the 1 kHz signals once a second at about 60 microvolts per count…... Listed under: AVR ATmega
Projects
1563. Morse Code Alarm Clock using ATtiny2313 microcontroller Morse Code Alarm Clock Modification (Almost) Trivial application
of an AT90S2313 or ATtiny2313 in an alarm clock to change the alarm from "BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP..." to
"WAKE UP" in Morse code. This was designed in response to a request and…... Listed under: AVR ATmega Projects, Clock
Projects
1564. 89C517 Segment Display using the Digital Time Data from Port0 7447 entegresinde and 7-segment displayreaches ' s.7447 -
integration mikrodenetleyiciden from binary code to show in the 7 segment displayis used. So when it comes to 0000 a, b, c,
d, e, f LEDs lights up g edi fireproof.7 segment displayis connected in parallel to each other ' s.Using the same…... Listed
1565. 8 Channel PWM using AVR microcontroller The assembly code given here was written to see what it would take to make an
AT90S1200 generate 8 channels of proper PWM. In this case, by proper, I mean with the maximum high frequency content
consistent with the needed duty cycle and give clock.…... Listed under: AVR ATmega Projects, PWM Projects
1566. AVR Programmer with ATMega8-16 About AVR Programmer This simple AVR Programmer will allow you to painlessly
transfer hex programs to most ATMEL AVR microcontrollers without sacrificing your budget and time. It is more reliable than
most other simple AVR programmers available out there and can be built in…... Listed under: AVR ATmega Projects
1567. AT89C52 DS1302 DS18B20 LCD On Time-Temperature Original Atmel micro controllers to use the at series with a good
example of ds1302 ds18b20 circuit 2 × 16 lcd indicator can be set with 4 buttons on The first button press and a bout at 2
minutes (time) setting with the buttons 2 and…... Listed under: AVR ATmega Projects
1568. Capacitance Meter using AVR microcontroller Digital Capacitance Meter This is a simple capacitance meter which can
measure capacitance value easy. There are some measurement methods for capacitance, at one time the capacitance was
measured with a impedance bridge or a dip meter. Recently typical capacitance meters can measure capacitance and…...
1569. Atmel Avr Project Circuit Archive 360 MB using ATmega8 microcontroller I collected a lot of site in the internet for various
atmel avr projects will not work with the idea of a day's archive is a grown up pretty. Atmel will be a solid resource for people
interested in the firm. Atmel AVR Project Circuit Archive; …... Listed under: AVR ATmega Projects, Memory - Storage Projects
1570. PC Temperature Meter using ATtiny15 microcontroller Port-Powered Temperature Meter This is a four-channel temperature measurmet adapter that
works without external power supply. It will suitable for measureing temperature and logging its data with a PC. The circuit diagram is very simple and

no adjustment is required, everybody will able to build…... Listed under: AVR ATmega Projects, Sensor - Transducer - Detector
1571. Computer controlled marquee at90s2313 74hc595 With all the details on a circuit different from that to which the shared a
marquee computer control program atmel at90s2313 source software image format you have the source schema and pcb,
orcad drawings. Marquee on a circuit different from that to which Marquee in…... Listed under: AVR ATmega Projects, Home
Automation Projects
1572. Frequency counter using AVR microcontroller Universal Counter The frequency counter is the most popular instrument in the
home maid instruments. I think that the reason why it is built widely is: it can be built easily because it is digital circuit, it is
generic measurement and many construction kits are…... Listed under: AVR ATmega Projects
1573. 8 channel LCD Teperature meter using microcontroller Description This is the fully featured, jammed packed temperature
readout unit. I can measure temperature from up at 8 DS1820 digital temperature sensors all on the same 1-wire bus. That's
right only 3 wires are needed to go to all the temperature sensors, GND, VCC…... Listed under: AVR ATmega Projects, LED
1574. Packet Radio using AVR microcontroller Here is some experimental hardware and software to transmit and receive AX.25
packets. It is essentially a PIC-E clone designed around a Atmel AT90S2313 with a few extra bells and whistles. I had picked
up a couple of MXCOM MX-614s at the TAPR display (I…... Listed under: AVR ATmega Projects, Radio Projects
1575. Nixie Clock with AVR using ATmega48 microcontroller Introduction: This is the hardware and source code for an Atmel
ATmega48 based four digit Nixie Tube Clock. Description: This was my second Nixie clock project. I wanted something a little
smaller / cheaper / simpler then my rather large B-7971 clock. I will post…... Listed under: AVR ATmega Projects, Clock Projects
1576. Atmel AT89C2051 hardware keylogers circuit with using AT89C2051 microcontroller Atmel On the PC keyboard PS 2
AT89C2051 keylogers circuit connection cable connects to the circuit between what is written in the wake of the program
running on the pc upon AT24C512 writes eeprom eeprom reading with KeeLog has decided to release an early version of…...
1577. AVR terminal for serial port using TSOP1738 microcontroller description (hardware) Above and below you can see the
terminal. The LCD display is represented by the connector X1. It has a HD44780 compatible LCD controller and I'm using the
4-bit interface to send data to the LCD controller. The LED's are multiplexed. I've seen…... Listed under: AVR ATmega Projects
1578. Atmel atmega projects l35 heat time display keypad using ATMega microcontroller Atmel ATMEGA series of three projects
are made with micro-controllers delivering projects bahramelectronic.ir Thank you brother Bahram's administrator. 1
- ATMEGA16 LCD display temperature measurement (LM35) 2 - ATmega8 application of the keypad display with 7 segmet 3
- ATMEGA32 with a thermometer (LM35) hours. For more detail: Atmel atmega projects l35 heat time display…... Listed under:
AVR ATmega Projects
1579. Atmel Bascom avr 8051 project, the circuit archive using AT89S8252 microcontroller Atmel series (AT89C2052, AT90S2313,
AT89S8252, etc.). wide range of PIC microcontrollers with an archive of high-quality circuit atmel version you can find a lot of.
Usb, alarm, lcd, nokia 3310, nokia 6100, display, LED, sms, telephone and so on. schema files to Protel PCB circuit has a lot
of…... Listed under: AVR ATmega Projects, Other Projects
1580. Heart of LEDs using microcontroller One of the requests we received after publication of the Christmas Star was "can you do different shapes?" Well,
with Mother’s Day coming up soon, we thought a heart would be appropriate. Now you can have something different to give to that special Mum
or…... Listed under: AVR ATmega Projects, LED Projects
1581. Atmel atmega128 clock ds1307 tda5410 hard disk using atmega128 microcontroller Previously called " Corrupted HDD
Evaluate under the heading "corrupted hard disks to evaluate the application, I mentioned a couple of hours on the web
projects I had used it with emery hardisk hours now, but quite professional and all of the shared resources, shared project
Circuit atmel ATMEGA…... Listed under: AVR ATmega Projects, Clock Projects
1582. Lux meters attiny26-16 light measurement circuit using attiny26 microcontroller Lux meter circuit atmel attiny26-
16 microcontroller based on the value of the LED displays on the display lux with LEDs placed on 2sk1061
MOSFETs. Interestingly, all of the source files in an application (pcb, diagrams, code) calibration circuit is shared also provided
information to Lux meter circuit diagram: The Lux…... Listed under: AVR ATmega Projects
1583. Atmel avr usb programmer using ATMEGA8 microcontroller A lot of programmers are growing for a USB programmer for Microchip PIC controllers
are Atmel avr usb programmer circuit atmelcilerde not idle in addition to the USB communication does not require a material ATmega8
ATMEGA48 can be done with either the source code of software…... Listed under: AVR ATmega Projects

1584. LCD Car Accelerometer using microcontroller Introduction The circuit is drawn for measurement of acceleration from –1000
mg until + 1000 mg. It can be placed in kantra'n the car and be supplied from the sheath of electric lighter. The circuit
includes one indicative LED and a screen LCD. Description The…... Listed under: AVR ATmega Projects, LCD Projects, Sensor -
1585. AVR LCD Microcontrolled Oscilloscope using ATmega32 microcontroller Features Frequency measurementVoltage input
Power supply Liquid Display Crystal Measurement display area Information displaying area: Auto triggering 10Hz - 7.7 kHz
(firmware 2.0 and above)24V AC / 30V DC 12V DC 128x64 pixels 100x64 pixels 28x64 pixels (Used from firmware 2.0 and
above) Auto Introduction A…... Listed under: AVR ATmega Projects
1586. VGA Monitor adaptor using AVR microcontroller Background of the project. Several months ago I tried to connect a
microcontroller system to a VGA monitor to output data in the form of text. I was surprised to find little on this subject on the
internet, to assist me in achieving this goal.…... Listed under: AVR ATmega Projects, Video - Camera - Imaging Projects
1587. Midi Generator using ATtiny26-8PI microcontroller This circuit based on ATtiny26 but it could be anyone microcontroller of
AVR family. Produce stable one MIDI tone and you can change it by press some keys like to change midi channel 0-15 ,
velocity 0-127, pitch 0-127. It is start from center tone…... Listed under: AVR ATmega Projects
1588. Universal Serial Bus (USB) Connectors Pinout All Types of USB Pinout Diagrames Universal Serial Bus connectors. These USB
connectors let you attach mice, printers and other accessories to your computer quickly and easily. The operating
system supports USB as well, so the installation of the device drivers is quick and easy, too. Compared to other ways of…...
Listed under: Blog, Circuits
1589. USB AVR programmer using ATtiny2313 microcontroller Introduction. Nowadays, USB is the most popular connection
between PC and peripherals such as AVR programmers, printers, scanners etc. For that reason I had to modify my old serial
AVR In-System-Programmer (ISP) to work with USB connection. You can say, "use a USB to Serial adaptor to…... Listed under:
AVR ATmega Projects
1590. 10 Bit analog to digital converter using ATtiny26 microcontroller Study the Analog to Digital capabilities of Atmel ATtiny26.
This tiny but mighty IC is really a miracle. One special thing is the internal 10-inputs multiplexed ADC circuit which can covert
analog voltages to bytes. This check circuit uses only 3 inputs. Of course you…... Listed under: AVR ATmega Projects
1591. SMS control 4 way remote control relays using ATtiny2313 microcontroller Introduction With this circuit we can control up
to 8 devices (4 devices in our example project), by sending a specific SMS message with any mobile phone. It's very useful
in the case that, at the place we have the devices, we have not a…... Listed under: AVR ATmega Projects, Phone Projects
1592. RF 2 channel remote control 418MHz using AVR microcontroller Introduction How many times you needed some remote
control to handle some electric device ? Many times. There are lot of remote controls like infrared, RF, SMS (like my other
circuit) and more. The basic small-range remote controls are 2, Infrared and RF (Radio Frequency).…... Listed under: AVR
ATmega Projects
1593. RCEN fuse programmer using AT90S1200A microcontroller Introduction: As you know the AT90S1200 microcontroller
includes an internal RC oscillator that is disabled by default. If you want to change it (enable or disable) you must to program
it with parallel mode. The most programmers work on serial mode that is not possible to program…... Listed under: AVR
ATmega Projects
1594. 80×32 LED matrix display using ATmega32 microcontroller The LEDMATRIX interface News: Now with lcd4linux driver I
recently purchased 10 SLM1608 (SLM1606) LED matrix display units from Ebay (you might also contact the seller directly at
op16@gmx.de). These are 16x16 LED matrix units with a green and a red LED per pixel allowing…... Listed under: AVR ATmega
Projects, LED Projects

1595. i2c interface to USB interface using attiny45 microcontroller Attach any I2C client chip (thermo sensors, AD converter,
displays, relais driver, ...) to your PC via USB ... quick, easy and cheap! Drivers for Linux, Windows and MacOS available. The
i2c-tiny-usb project is an open source/open hardware project. The goal of i2c-tiny-usb is to…... Listed under: AVR ATmega
1596. Acceleration sensing USB interface using Atmega8 microcontroller Contents The hardware The USB interface Calibration PC
assisted calibration Self calibration Software Drivers Joystick drivers Maemo drivers The input event subsystem Setting
permissions Enigma FAQ Downloads The TiltStick is a small acceleration sensing device in form of a USB stick. It's using a
two…... Listed under: AVR ATmega Projects, Sensor - Transducer - Detector Projects
1597. Wireless Lan for AVR microcontrollers The complete WLAN solution for AVR and other CPUsThe page is about equipping an
Atmel AVR microcontroller based system with a Prism WLAN interface. This document is intended for people that already
have experiences with the AVR microcontrollers and teaches them how to add a…... Listed under: AVR ATmega Projects,
1598. AVR Compiler toolchain for MAC using ATmega8 microcontroller The following instructions are from early 2007 and are pretty outdated by now.
They are still here for reference, but they are not maintained anymore and very likely won't work with recent versions of MacOS anymore. After having
developed software for the AVR under Windows…... Listed under: AVR ATmega Projects
1599. Java virtual machine for the Atmel AVR ATmega8 The NanoVM is a java virtual machine for the Atmel AVR ATmega8 CPU, the
member of the AVR CPU family used e.g. in the DLR Asuro robot, manufactured by AREXX engineering. With the NanoVM,
the Asuro can be programmed in the popular Java language using…... Listed under: AVR ATmega Projects, CNC - Printing
Machines Projects
1600. EPROM adapter for ATMEL 89 Series Flash Microcontroller Programmer Ver 2.0 Devices The EEprom programmer software
supports the following devices. 28C16 28C256 28C17 29C256 28C64 Hardware Diode D1 and resistor R1 provide the VDD
isolation when programming the 24 pin devices. The jumper J3 must be shorted for 24 pin devices, and open circuit for 28…...
Listed under: AVR ATmega Projects, Other Projects
1601. Digital Stop Watch with ATmega8 using microcontroller In this tutorial we will make a "Digital Stop Watch" using an AVR
ATmega8 Microcontroller. This will help you learn many concepts like Multiplexed Seven Segment Display Interfacing Using
AVR Timers Using Interrupts And many others too. The code is written in C language for…... Listed under: AVR ATmega
1602. Relay Timer with ATmega8 AVR MCU Timer are widely used in industrial and domestic application for automating tasks.
Microcontrollers can be used to design versatile and accurate timers with ease. Here I present a simple timer that can be
used to turn on/off a load after user specified time. The Timer…... Listed under: AVR ATmega Projects, Home Automation
Projects
1603. Remote Controlled Fan Regulator using ATmega8 microcontroller This device can be used to remotely control the speed of
an AC fan and to switch it on or off. The remote control is a cheap NEC Format remote, usually supplied with small DVD
players. Three buttons are used to command the circuit. The…... Listed under: AVR ATmega Projects, Home Automation
Projects
1604. ATmega8 based RPM Meter How you can make a simple RPM Meter using AVR ATmega8. The RPM meter we will be making
is a contact less type, i.e. it measures the RPM of a rotating object without actually making any contact with it. An IR
reflectance sensor will be…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1605. ATmega8 Based Smart Code Lock Here is a project for beginners using Atmel AVR ATmega8. The project uses some
techniques that are very useful for designers to learn and utilize. Alphanumeric LCD Module Interfacing. 4x4 Keypad
interfacing. PWM Control of LED (Used to dim the back-light of LCD, like in…... Listed under: AVR ATmega Projects,
1606. ATmega8 Based Multi channel IR Remote Today I will present an easy to build Multi channel IR Remote control system. It can
control heavy loads (Up to AC 220V 6 Amps or smaller) with a touch of remote control. A total of 5 devices can be controlled
from a distance of…... Listed under: AVR ATmega Projects, Other Projects

1607. AVR RGB LED and Sound Show using ATmega168 microcontroller The tutorial is well planned and executed. I really liked the
RGB LED and Sound show given at the end. I will try it and tell how it works. Till then you can read the rest of the article here.
Working with Atmel AVR Microcontroller…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1608. Visualize ADC data on PC Screen using USART AVR Project using microcontroller ADC (Analog to digital converter) is a
commonly used peripheral. We use it everyday to interface with several analog sensors. Many times a nice visualization of
ADC data is required during learning about new sensors. For example you just bought a analog sound sensor, and…... Listed
under: AVR ATmega Projects, Sound - Audio Projects
1609. PC Controlled Robot using ATmega32 In this tutorial we will discuss a simple PC controlled robot. The Robot PC link will be a
RS232 serial line. The robot will have only five commands. Move forward (RS232 char 'F' or 'f') Move backward (RS232 char 'B'
or 'b') Turn Left (RS232…... Listed under: AVR ATmega Projects, Robotics - Automation Projects
1610. AVR ATmega8 Project LED Moving Message Display using ATmega8 microcontroller An interesting project that can be done
using Microcontroller is a LED message scroll er. It teaches you a quite lot of things. So I decided to make one. I made the
hardware design modular and cascadeble That means the whole display is made up…... Listed under: AVR ATmega Projects,
1611. PS2 Keyboard Interface with AVR MCU using ATmega8 microcontroller A PC keyboard is an old and trusted human machine
interface. Most peoples are familiar with it. When a text entry is required it is the best method. If we can interface the PC
keyboard with an AVR MCU we can create a whole lot…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -
ISP) Projects
1612. Line Following Robot using AVR ATmega8 One of the most basic autonomous robot you can build is a line following
robot(LFR). This type of robot is run over a white surface which has an arbitrary path drawn over it by using back paint. The
task of the robot is to run…... Listed under: AVR ATmega Projects, Robotics - Automation Projects
1613. SMS Based Voting System – AVR GSM Project using ATmega32 microcontroller Hi friends ! Here I am showing a
microcontroller based project called the "GSM Based Voting System". Using this system you can ask your users to vote for
any of the four options. Four available options are identified by a letters 'A', 'B', 'C' and…... Listed under: AVR ATmega Projects,
Phone Projects
1614. Interfacing TCS3200 Colour Sensor with AVR ATmega32 Detecting colour of an object can be an interesting and useful
electronic application. It can be realized using a colour sensor like TCS3200 and a general purpose microcontroller like AVR
ATmega32. TCS3200 Colour Light to Frequency Converter Chip TCS3200 chip is designed to detect the…... Listed under: AVR
1615. AVR Music Player with Alarm Clock using AT90USB1286 microcontroller This music player project built based on
AT90USB1286 microcontroller. It uses VS1033D music decoder which integrates music file decoding and digital-to-analog
output. Other main part including 16×2 character LCD display, ST7066/HD44780 compatible, using 3.3V instead of 5V and
DS1307 real time clock. By finishing this…... Listed under: AVR ATmega Projects, Clock Projects
1616. AVR Power Usage Logger using ATmega168 microcontroller This ATmega168-based project monitors household power usage
and logs it to an SD card. Signals from voltage and current detectors amplified LMC6484AIN quad op-amp and then AVR
microcontroller computes the power consumption using the formula P=VxI. The voltage and current are each sampled at
9615…... Listed under: AVR ATmega Projects
1617. Energy Monitoring Transmitter using Atmega328 microcontroller This energy monitoring transmitter, known as emonTx, is an
Atmega328-based small wireless energy monitoring node. It also fully compatible with Arduino IDE. EmonTx is designed to
take inputs from multiple CT sensors, optically from a pulse-output utility meter and from multiple one-wire temperature
sensors. The…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN Projects
1618. Wireless Human Health Monitor using ATmega644 microcontroller The aim of this ATmega644-based project is to build a
portable device implementing wireless technology and taking full advantage of the wide-spreading Internet to provide a
convenient solution to monitor human health. The health information acquired on the portable side transmits to the server
wirelessly…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN Projects, Medical - Health based Projects
1619. AVR Digital Hum Nuller using ATmega168 microcontroller This ATmega168-based digital comb filter built to clean a realtime audio signal. It can
remove the ubiquitous 60Hz (50Hz in some countries) hum noise caused by power lines and household electrical wiring. Since the noise is not strictly
sinusoidal it is necessary to remove all…... Listed under: AVR ATmega Projects, Other Projects

1620. DC Servomotor Controller System Meter using ATtiny2313 microcontroller The ATtiny2313-based project is an experiment on
the closed loop DC servomotor control system (SMC) by Elm Chan. It can be used for practical use with/without some
modifications. The closed loop servo mechanism requires real-time servo operations, such as position control, velocity
control and torque…... Listed under: AVR ATmega Projects, Motor Projects
1621. Low Picofarad Capacitance Meter ATtiny2313 microcontroller This little instrument, named as Pico C, can be used to measure
capacitances down to fractions of a picofarad. It built based on ATtiny2313 microcontroller. It has range: <1 pF to 2000 pF
(guaranteed); 2500 pF possible and resolution: 0.1 pF. To read the result,…... Listed under: AVR ATmega Projects, Metering -
Instrument Projects
1622. Ear Trainer using ATMega644 microcontroller The goal of project is to helps people develop the musical skills of perfect pitch
and relative pitch. Push buttons allow the user to navigate a graphical user interface (GUI) on a liquid crystal display (LCD). In
perfect pitch training mode, a note is played…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects
1623. AVR Data Logger with MicroSD using ATmega32 microcontroller This project shows you how to store data into microSD card
in files with FAT32 format using microcontroller AVR ATmega32. The MCU receives sensor’s data through internal ADC. You
can connect up to 8 different sensors to the system. In this project, Dharmani uses one…... Listed under: AVR ATmega Projects,
1624. AVR Code Debugger using AVR microcontroller AVR Code Debugger is useful tool to help you debug code without require
resource in the MCU you are debugging. It only use 1 I/O pin, and is connected to a serial port from the host PC. Using a
VT100 terminal to capture the output…... Listed under: AVR ATmega Projects, RTOS - OS Projects
1625. Electric Spinning Wheel using ATmega8 microcontroller The Electric Eel Wheel is a smart electric spinning wheel which helps
you spinning the fiber of your choice into yarn easily instead of traditional wheel. This Electric spinner is lighter and smaller,
making it easier to take your spinning with you. You can control…... Listed under: AVR ATmega Projects, Motor Projects
1626. Atmega Rechargeable Battery Capacity Tester using ATMega168 microcontroller This ATMega168-based battery tester allows
you to find out the overall capacity of the rechargeable battery. It can shows how long will a battery last from the time it’s
fully charged to the time that the “low battery” indicator comes on your device. It can…... Listed under: AVR ATmega Projects,
1627. Simple Automatic Battery Discharge Analyzer using ATmega48 microcontroller The project allows you to analyze
characteristics of unknown/junk battery especially the capacity and variation of the voltage on discharge. It is controlled with
a PC via a serial port. No external power supply is required because it is powered by RS-232C signals. It uses…... Listed under:
AVR ATmega Projects, Battery Projects
1628. AVR Security Keypad Lock using ATtiny2313 microcontroller The Security Keypad Lock Project is a basic access control system
based on ATtiny2313. It can be modified to protect just about anything. The “Code Lock” ability will allow the rightful user to
deploy the platform to any property that requires simple password-protection. The “AVR”…... Listed under: AVR ATmega
Projects, Security - Safety Projects
1629. Speaking Calculator using AVR ATmega88 microcontroller This Speaking Calculator project is an interesting device built just
by three chips that can be very useful to blind people. The system has four basic operations (addition, subtraction,
multiplication and division), and the functions: clear all, change of sign (+/-), inverse (1/x), square root…... Listed under: AVR
ATmega Projects, Sound - Audio Projects
1630. Handy Password Managing System, Lord of the Keys using AVR ATmega168 The Lord of the Keys is password managing
system that able to store many usernames and passwords inside a Java Card™ smart card (one of the most secure methods
to store confidential information). Whenever a dialog box appears in an application or web browser requesting…... Listed
under: AVR ATmega Projects, Security - Safety Projects

1631. AVR LED Candle using ATtiny85 microcontroller This LED candle is built to mimic the look of a traditional candle without the
dangers associated with an open flame. It uses high brightness LED and is controlled by ATtiny85. It could be useful as movie
props where you cannot afford to have a…... Listed under: AVR ATmega Projects, Home Automation Projects
1632. Mini Logic Analyzer using ATmega8 microcontroller Mini Logic analyzer is ATmega8-based electronics tool that can be used
to watch and analyze logic transitions 0 or 1 of a digital data signal. It comes with Nokia 3310/5110 LCD to display signal and
it has 4 channel inputs. A digital data signal can…... Listed under: AVR ATmega Projects, Other Projects
1633. Clever Clapper using ATtiny2313 microcontroller A “Clapper” is a device that will turn on or off an AC appliance that is
plugged into it, such as a lamp or fan when it “hears” you clap twice in approximate succession. Pete has built a Clever
Clapper with various task. If user…... Listed under: AVR ATmega Projects, Other Projects
1634. AVR Ultrasonic Spheroid Levitation Device using ATMega16 microcontroller Introduction The goal of this project was to
design and build a gaming device capable of levitating a ping pong ball at varying heights based on the proximity of the user
to the device, utilizing a multi-tasking kernel on the ATMega16 platform. The project incorporates…... Listed under: AVR
ATmega Projects, Game - Entertainment Projects
1635. AVR Based Mobile Phone using AVR ATmega128A microcontroller AvrPhone is ATmega128A-based simple mobile phone with
touch screen and SIM100S GSM module. The display uses 2,4″ LCD with a resistive touch screen and ILI9325B driver (16 bit
parallel bus). The LCD breakout board contains SD card slot and XPT2046 touchscreen controller. They both are…... Listed
under: AVR ATmega Projects, Phone Projects
1636. AVR Wide Range LC,F, ESR Meter using AVR ATMega88PA-PU microcontroller LCFesR meter is a precise, wide range meter
that can measure inductivity (L), capacity (C), frequency (F) and equivalent series resistance of a capacitor in-circuit (ESR)
based on AVR ATMega88PA-PU microcontroller. It can be easily built with homemade one or double-faced PCB and available
electronic…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1637. AVR Touchpad Handwriting Recognition using ATmega644 microcontroller This ATmega644-based project implements a
touchpad input system which takes user handwriting input and converts it to a printed character. Currently, the device only
recognizes the 26 letters of the alphabet, but it could be easily generalized to include any figure of completely arbitrary
shape,…... Listed under: AVR ATmega Programmers, AVR ATmega Projects, LCD Projects
1638. AvrX, Real Time Kernel using AVR microcontroller AvrX is a Real Time Multitasking Kernel for AVR microcontrollers written in
assembly. Total kernel size varies from ~500 to 700 words depending upon which version is being used. Since the kernel is
provided as a library of routines, practical applications take up less space…... Listed under: AVR ATmega Programmers, AVR ATmega Projects
1639. AVR High Voltage Programmer Using Arduino AVR microcontroller AVR microcontroller uses fuse bits to set its operational
parameters like watchdog timer settings and change speed of the internal oscillator. Most fuse bits can be set or reset
without worry. You can flash it into one state and then flashed back again using an…... Listed under: AVR ATmega Projects,
1640. STK500 Compatible ISP using AVR microcontroller AVR-Doper is an STK500 compatible In System Programmer (ISP) and High
Voltage Serial Programmer (HVSP). It comes with a built-in USB to Serial adaptor to connect to modern host computers
which often don’t have a serial interface. The project implements a low speed USB device…... Listed under: AVR ATmega
1641. TinyRealTime, Small Real Time Kernel for AVR using atmega644 microcontroller Real-time kernel (RTK) is useful to run several
task or protocol on one CPU. Since only one task at a time can be executed by MCU, RTK used to make each task think it
owns the whole machine. RTK will handle which task has to…... Listed under: AVR ATmega Programmers, AVR ATmega Projects
1642. Ultrasonic Security System using Atmega644 microcontroller This portable security system is built based on Atmega644
microcontroller. It can detect intruders based on their physical presence. The system uses URM37v3.2 ultrasonic sensor which
is connected to MCU through rs232 serial communication. To rotate sensor for wide coverage range, the system is
equipped…... Listed under: AVR ATmega Projects, Security - Safety Projects

1643. Auto Sensing Sous-Vide Cooker using AVR microcontroller This low cost AVR-based Sous-Vide Cooker is able to auto-
calculate the appropriate time for cooking a certain thickness of meat using heat transfer equations. It can maintain a set
temperature for extended periods of time. The project implements advanced features such as a water level…... Listed under:
AVR ATmega Projects, Sensor - Transducer - Detector Projects
1644. AVR Thermocouple Temperature Meter using ATmega164 microcontroller The benefit using thermocouple sensor for
measure temperature is it has wide range measurement (-200 °C to +1350 °C / -328 °F to +2462 °F range for Type K),
inexpensive, interchangeable, and is supplied with standard connectors. To get temperature value from output of a…... Listed
1645. AVR Based Car Diagnostic Tools using ATmega169 This project focuses on tapping into GM pre-1996 car and light truck
diagnostic information. These systems are commonly referred to as OBDI, or ALDL (Assembly Line Diagnostic Link). They are
based, in part, on the GM-specific 8192-baud ALDL standard that was used starting in the…... Listed under: AVR ATmega
Programmers, AVR ATmega Projects
1646. 5 Channel USB Analog Sensor with AVR using ATmega48 Microcontroller This project demonstrates how to build a simple
module to read analog sensor and send the data to PC using USB connection. The project uses ATmega48 as main processor
and USB FTDI serial-to-usb cable. Simply put header pins on your device which you can plug…... Listed under: AVR ATmega
1647. AVR Switch Timer using ATmega8 Microcontroller To get better UV expose, Andrianakis has built new Switch Timer that will
turn of his UV exposure box after some time. The timer uses ATmega8 as main processor and two 7-segments LED as display.
There are two buttons for set and start the timer.…... Listed under: AVR ATmega Projects, Calculator Projects
1648. Wireless Internet Radio Receiver using AT90CAN128 Microcontroller This stand-alone internet wireless music player, named
as Wireless MP3 (WMP3), uses Atmel AVR AT90CAN128 microcontroller as main ‘brain’. The device can play music from
internet radio stations like Shoutcast (www.shoutcast.com), connect to shared network drives and play mp3 files. Ubiquitous
802.11b wireless link is…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN Projects
1649. Low-cost AVR programmer Before using this programmer.... Be carefull with using this programmer, because it has no
insulation circuitry! Especially when using high voltages e.g. 110/230 Vac on your project. One mistake and your day can be
ruined, your expensive PC distroyed! Part list: 7x 220 ohm 1x…... Listed under: AVR ATmega Programmers, AVR ATmega
Projects
1650. SP12 serial programmer software SP12 supports the following devices: AT90S1200, AT90S2313, AT90S8515, AT90S4414,
AT90S2323, AT90S4434, AT90S8535, AT90S2343, ATtiny22, AT90S2333, AT90S4433, ATtiny12, ATtiny13, ATtiny15L, ATtiny26,
ATtiny25, ATtiny45, ATtiny85, ATtiny2313, ATtiny861, ATmega103, ATmega603, ATmega161, ATmega162, ATmega163,
ATmega168, ATmega8515, ATmega8535, ATmega8, ATmega16, Atmega32, ATmega48, ATmega88, ATmega128, ATmega2561,
AT90PWM3. Source: Pitronics Download the…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects
1651. AVR assembly language What is an AVR ? First of all AVR stands for: Advanced Virtual RISC. The founders are Alf Egil Bogen
Vegard Wollan RISC (also forms AVR). An AVR is a small microcontroller (chip, IC) which is switching digitally (controller) by
means of so called i/o's…... Listed under: AVR ATmega Projects, Clock Projects
1652. White 7-segments clock ATtiny26 Part list 1x ATtiny26 1x xtal 4.096MHz 2x 27pf ceramic 4x 7-segment white CC 2x
pushbutton 1x 78L05 1x 47uF/16V electrolytic 1x 0.1uF/16V tantalium 1x 10k 1x 100n multilayer 8x 150 Ohm 4x 6k8 Ohm 4x
BC327-25 PNP Features (BETA) 1. Select Hrs/Min or Min/Sec…... Listed under: AVR ATmega Projects, Clock Projects
1653. Controlling internal DAC AT90PWM3 using microcontroller Part list 1x AT90PWM3-16SQ 2x SLO2016 LED display 1x 22uF/25V elco SMD 2x 0.1uF/16V
tant. 1206 2x 10 kOhm 1206 3x 100n multilayer 1206 1x coil 10uH SMD 1x rotary encoder (Sharp) Digital voltage control unit his is how a value is
stored into…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects

1654. Controlling SpeakJet with an AVR microcontroller using ATmega88 microcontroller Core Features: · Programmable, 5 channel
synthesizer. · Natural phonetic speech synthesis. · DTMF and other sound effects. · Programmable control of pitch, rate, bend
and volume. · Programmable power-up or reset announcements. · Multiple modes of operation. · Simple interface to
microcontrollers. · Simple…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1655. Modular User Interface System using ATMega88 microcontroller The IOSTRING is a modular physical user interface system
which consists of a series of three basic board modules designed around the Atmel AVR AtMega88 MCU. Each module type
can handle switches, pushbuttons, rotary selector switches, rotary shaft encoders, potentiometers, LED’s, LCD displays, and
an…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1656. Switching between Red, Green and Blue (or Blue1 or/and Blue2 for an RGBB type) using AVR microcontroller Switching
between Red, Green and Blue (or Blue1 or/and Blue2 for an RGBB type): An RGB LED is a LED which has three (or four for an
RGBB type) semi-conductor LED's in one normal housing i.e. standard 5 mm. The Red LED is made of…... Listed under: AVR
ATmega Projects, Other Projects
1657. AVR Based Operating System using ATMega32 microcontroller kaOS project is real-time, multithreaded, preemptive
operating system for the Atmel Mega32 microcontroller. It can loads and executes programs from a Secure Digital or MMC
card. The system waits for a card to be inserted and a reset button to be pressed, at which point…... Listed under: AVR
ATmega Programmers, AVR ATmega Projects
1658. 3D Color LED Graphics Display using ATmega32 microcontroller This 3-dimensional graphics display system which named as
MaJaTron consists of 125 RGB LEDs arranged in a cube of 5x5x5 dimension. Each LED is a multicolor Red, Green and Blue LED
and the control circuit of the system can individually control the intensity of each…... Listed under: AVR ATmega Projects, LED
Projects
1659. A GLCD connected to an AVR microcontroller using ATmega8 microcontroller A GLCD connected to an AVR microcontroller
The PVG120602EGE is a 128x64 pixel graphic (grey) LCD with lightblue EL backlight and two KS0108 controller chips and one
KS0107 line (colums) driver (64 display lines COM1 - COM64) The first KS0108 drives segments 1 to 64…... Listed under: AVR
ATmega Projects, Video - Camera - Imaging Projects
1660. Open Source AVR Temperature Controller using ATmega48 microcontroller The open source project allows you to control DC
appliances based on the temperature of two thermistor inputs. It uses AVR ATmega48 as main processor. The controller has
both green and white LEDs to indicate status. The project output is connected to N-Channel MOSFET, AOD444,…... Listed
under: AVR ATmega Projects, LCD Projects, Temperature Measurement Projects
1661. Pinning LCD display 1601 using microcontroller Pinning LCD display 1601A: Pin no. Symbol Function 1 Vss GND 2 Vdd + 5V 3
Vo Contrast Adjustment 4 RS H/L Register select signal 5 RW H/L Read/write signal 6 E H->L Enable signal 7 DB0 H/L Data
bus line 8 DB1 H/L Data…... Listed under: AVR ATmega Projects, LCD Projects
1662. Simple USB AVR programmer, USBasp using ATMega8 microcontroller USBasp is low cost USB in-circuit programmer for
Atmel AVR micontrollers. The hardware consists of an ATMega88 or an ATMega8 and a couple of passive components. The
programmer uses a firmware-only USB driver, no special USB controller is needed. Its programming speed is up to…... Listed
under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1663. Controlling 7-segments LED displays using AVR microcontroller The many posibilities....Non Multiplexed: 1. One or two displays directly to the i/o's 2.
One display with a 74LS247 3. Two displays with a 74HC595 and two 74LS247 Multiplexed: 1. Two displays with a 74LS247 and 2 i/o's 2. Two displays
with a 74HC595 and…... Listed under: AVR ATmega Projects, LED Projects

1664. Programming AVR ATxMega using USBasp and ATxmega microcontroller ATxmega programmer has different interface than 8-
bit AVRs. It uses PDI interface instead of ISP. If you don’t want to buy new programmer for ATxmega you can try this little
hack done by Szu. He uses USBASP (USB in-circuit programmer for Atmel 8-bit AVR controllers)…... Listed under: AVR ATmega
1665. TIL311 / INL0397-1 Hexadecimal Display usning AVR microcontroller Pin numbers: PIN 1 LED SUPPLY VOLTAGE PIN 2 LATCH
DATA INPUT B PIN 3 LATCH DATA INPUT A PIN 4 LEFT DECIMAL POINT CATHODE PIN 5 LATCH STROBE INPUT PIN 6
OMITTED PIN 7 COMMON GROUND PIN 8 BLANKING INPUT PIN 9 OMITTED PIN…... Listed under: AVR ATmega Projects, LED
Projects
1666. Head-Controlled Keyboard And Mouse For Disabled, using AVR and ATMega32 microcontroller Easy Input is a head-
controlled keyboard and mouse input device for paralyzed users. The system is built based on AVR ATMega32. It uses user’s
head movement to control mouse movement on the monitor and user’s eye blinking to activate mouse click. Two main
sensor used…... Listed under: AVR ATmega Projects, Sensor - Transducer - Detector Projects
1667. Advance Fire Alarm through Mobile Phone using microcontroller An automatic fire alarm system is designed to detect the
unwanted presence of fire by monitoring environmental changes associated with combustion. In general, a fire alarm
system is classified as either automatically actuated, manually actuated, or both. Automatic fire alarm systems are
intended to notify …... Listed under: AVR ATmega Projects, Phone Projects
1668. 93C66 EEPROM chip with an AVR microcontroller How to program a 93C66 EEPROM chip with an AVR microcontroller? The
93C66 is a serially (MICROWIRE) Electrically Erasable Programmable ROM (EEPROM) chip with 4 kbit (4096 bit, can be
ORGanized as 256 x 16bit or 512 x 8bit) memory space. Here a DIL version…... Listed under: AVR ATmega Projects,
1669. DS1669 Digital Potmeter UP/DOWN using microcontroller Part list:1x AT90S1200-12PI 1x DS1669 (Dallas) 1x 78L05 2x
1N4007 1x 4MHz X-tal 2x 27pf 1x 22pF 1x 47uF/16V 1x 100n polycarbonate 3x 100n multilayer 1x 100 ohm 1x 10k ohm 1x
820 ohm 1x 100k trimpot 1x 10k lin. potmete DS1669 Digital Control: With…... Listed under: AVR ATmega Projects, Metering -
Instrument Projects
1670. DS1802 Digital Volume Control using microcontroller Part list: 1x AT90S1200 1x DS1802 (Dallas) 1x 78L05 1x 8MHz ceramic
resonator 1x 22pF 1x 47uF/16V 1x 47n polycarbonate 4x 100n multilayer 1x 100 ohm 1x 10k ohm 1x 820 ohm 1x 100k
trimpot 1x 10k lin. potmeter Digital Controlled Potmeter: (also known as…... Listed under: AVR ATmega Projects, Metering -
Instrument Projects
1671. Helianthus: The Solar Tracking System using ATmega16 microcontroller Renewable energy solutions are becoming
increasingly popular. Photovoltaic (solar) systems are but one example. Maximizing power output from a solar system is
desirable to increase efficiency. In order to maximize power output from the solar panels, one needs to keep the panels
aligned with the…... Listed under: AVR ATmega Projects, Other Projects
1672. 16 LED Knight Rider using 74HCT138 microcontroller Part list: 8x LED (red) 1x 180 ohm 1x 10k ohm 1x 33k ohm 1x 2u2/16V
1x 74HCT191 1x 74HCT132 2x 74HCT138 1x 78L05 1x 47uF/16V 1x 100n 2x 1N4007 Yet another version: Here an example
with 4 TTL ICs. This is I think the…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, LED
Projects
1673. 8 LED Knight Rider using AVR microcontroller Another version: In this version I took PORTB of the AT90S1200 AVR
microcontroller as you can see in the diagram, because this makes it simpler to let 8 LEDs flash back and forth. Set the Data
Direction Register of port B as an output, the…... Listed under: AVR ATmega Projects, Other Projects
1674. 6 LED Knight Rider using ATtiny22 microcontroller Part list: 6x high eff. LED 2x 330 ohm 1x ATtiny22* 2x 1N4007 1x 100n 1x
47uF/16V 1x 78L05 * The ATtiny22 is obsolete, replace with one of the folowing AVRs: AT90S2343 / ATtiny13 / ATtiny45.
History of the back and forth flashers.... In the…... Listed under: AVR ATmega Projects, Other Projects
1675. Temperature Sensor Using ATmega8 and display using LCD(16×2) STEP 1: Circuit Diagram LCD other Pin's 1,2,3,15,16 as usual
not shown. Temperature Sensor (LM35) Circuit STEP 2: Programming Code Compile Using Codevision AVR View C Code STEP
3: Burn The Hex In ATmega8 View Hex Code (Make Sure grounds are common otherwise it will…... Listed under: AVR ATmega

1676. PCM Audio Based Door Bell using Atmega32 microcontroller This is a simple procedure to play PCM audio on any AVR
microcontroller. AVR's high speed PWM is used to play the audio. It almost sound fine and can be used for simple projects
that require sound effects. The code is compiled in winavr GCC…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1677. AVR Based CRO using Atmega16 microcontroller STEP 1: Circuit Diagram Components ATmega16 MAX232 0.1uf Capacitor -
---- 4pcs DB9 Connector 7805 for 5v power supply STEP 2: Programme Code (Compile using Codevision AVR & Burn in
Atmega16 ) View C Code STEP 3: Here We have used ADC5 of ATmega16 so…... Listed under: AVR ATmega Programmers, AVR
ATmega Projects
1678. Dotmatrix using ATtiny2313 microcontroller On this page you will find a scrolling LED sign based on the ATtiny2313 AVR
microcontroller, which you can build yourself (when finished) Other names for this device can be: Moving message sign,
Message crawler, Scrolling message, message display, etc. The idea is to let…... Listed under: AVR ATmega Projects, Other
Projects
1679. Easy Breadboarding using ATMega microcontroller When I'm fiddling about with electronics I want to be comfortable about
it. Therefore I built some things to make by breadboarding life a little simpler. One example is the Network Breadboard
Interface. Another one is this little project. These little pcb's can be put…... Listed under: AVR ATmega Projects, Development
1680. Monochrome Composite Video using Atmega8 This article describes the design of a Text on TV project. It takes serial data
and displays text on a TV screen. The hardware part of this project is pretty simple. It uses an Atmega8 microcontroller that
runs with a 16 MHz crystal. The article…... Listed under: AVR ATmega Projects, Video - Camera - Imaging Projects
1681. Tea Timer using ATTiny2313 microcontroller I usually drink a lot of tea, and sometimes the tea tastes a lot better than
average, which means that most times I make tea I fail at least partially. The taste of the tea depends on a lot of variables: The
make of the…... Listed under: AVR ATmega Projects, Home Automation Projects
1682. Kitchen Timer using ATTiny2313 microcontroller At the moment I do not have a kitchen timer. Not because I do not want
one, (they're cheap enough to buy) but because it seems impossible to buy a kitchen timer with a decent user interface. That
means I have to build my own,…... Listed under: AVR ATmega Projects, Home Automation Projects
1683. Power usage monitor using Atmel AVR using Atmega168 microcontroller This project uses Atmega168 microcontroller to
compute the power usage at home and logs it to an SD card. It has a graphical LCD display too that shows the power usage
as a strip chart. Besides, the voltage and current waveforms can also be displayed…... Listed under: AVR ATmega Projects,
1684. Programmer UsbAsp using AVR microcontroller This morning (2009-12-31) I built my 4th AVR programmer. USBasp. I built
this one because I wasn't completely happy with my 3rd programmer and because I want to play with a software USB stack. I
do know that it works (I just reprogrammed 2 old…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects
1685. Programmer using ATMEGA8 microcontroller The programmer I use is built from a kit I bought at Tuxgraphics. There are
several reasons I bought this kit. It is open source, works with avrdude. It connects to USB. It is a lot faster then my old
programmer (Programs an ATMEGA8 in…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1686. Beamer Control using attiny2313 microcontroller Beamer Control: Schematic Source code I made this project for Henk. He
has a beamer for watching movies and a motor controlled screen. The purpose of this project is very simple. If he turns his
beamer on, the screen must to down. And if the…... Listed under: AVR ATmega Projects, Home Automation Projects
1687. Door Opener using ATTiny2313 microcontroller Door Opener: Schematic Source code I made this little project for Hans, yet another brother of mine. (I
have 5 brothers.) He had a garage door to control and bought a little RF transmitter and receiver to control his door. Leo made a nice cabinet…...
Listed under: AVR ATmega Projects, Home Automation Projects

1688. Dimmer using ATTiny2313 microcontroller Dimmer: Schematic Source code I made this project for Leo, a brother of mine. We
had an old remote control of a video recorder laying around and he wanted some dimmers for all the lights in his house. I
didn't have much experience with programming…... Listed under: AVR ATmega Projects, Home Automation Projects
1689. 2 Bit u Stepper using microcontroller This is the second stepper motor driver circuit I build. The first one had 4 linear current
sources and got so hot it was barely usable. It had some cool leds though. When I was searching for a better schematic on
the internet I couldn't…... Listed under: AVR ATmega Projects, Motor Projects
1690. Oscilloscope using AVR microcontroller Designing a professional digital oscilloscope is a pretty complex task wich makes
them also pretty expensive. Therefore I concluded it's nothing more than a daydream to design one of those. It's far more
realistic to limit the design of this instrument to something a bit…... Listed under: AVR ATmega Projects, Metering -
Instrument Projects
1691. LC Meter using AVR microcontroller LC Meter: Schematic Source code This is the project I am currently working on (2010-01-
23). The LC meter is based on Elmcie or Elsie and other similar LC meters. This project is in a very early prototype stage and is
at the moment only capable…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1692. Power Supply using AVR microcontroller Katja & Guido at Tuxgraphics sell a very affordable little AVR controlled power
supply. That power supply can be controlled by sending it commands by I2C. Because I already have a pretty universal
network connected to my PC it seems very logical to me to…... Listed under: AVR ATmega Projects, Other Projects
1693. Looking for expanding RAM for your Atmega128 An Atmega128 microcontroller has got 4K of built in static RAM, which is
pretty enough for small and medium range projects that do not involve huge amount of data processing. But if you think you
need more than that for your application, you can expand…... Listed under: AVR ATmega Projects, Other Projects
1694. Cellphone controlled robot vehicle using ATmega16 microcontroller When we talk about wireless robot vehicle, we usually
think about the RF circuits. But this project is different. It uses a mobile phone to control the motion of a robotic vehicle, and
therefore, the range of operation is as large as the coverage area…... Listed under: AVR ATmega Projects, Phone Projects
1695. Multi-channel temperature logger using Atmega48 microcontroller This project describes how to use all the 8 ADC channels
of an Atmega48 microcontroller to read temperature sensors and the measured data to a PC for logging by using the built-in
USART capabilities of the chip. For demonstration, the temperature sensor used is LM335…... Listed under: AVR ATmega
1696. Turn your TV into a Digital Voltmeter using Atmel’s AVR 90S1200 microcontroller This is an interesting voltmeter project that
display the measured voltage on a TV screen, in giant digits as well as with analog bar. It also records the maximum and
minimum values of measurements. The project was built by Alberto Ricci Bitti and was published…... Listed under: AVR
1697. A physical display device for website visitors based on Atmega168 If you have a blog or website and want to make a physical
device to display the number of visitors, this project might be interesting to you. It describes about a similar device that can
be directly connected to the internet via router and counts…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN
Projects
1698. A multifunction digital meter using Atmega128 microcontroller This is a multifunction bench test instrument built using an
Atmega128 microcontroller and incorporate a lot of functions like voltmeter, ammeter, logic analyzer, frequency generator,
frequency counter and also provides regulated DC power supply. This device is interfaced with a Windows PC to display the
measurements.…... Listed under: AVR ATmega Projects, Metering - Instrument Projects

1699. AVR digital clock with white seven segment LED display using ATtiny26 microcontroller This is a digital clock project based on
an ATtiny26 microcontroller, displaying time on four seven segment LEDs. The seven segment LEDs glow bright white and are
multiplexed through PORTB pins, whereas the segments are driven by PORTA pins. The time is normally shown in…... Listed
under: AVR ATmega Projects, Clock Projects
1700. Portable 2.4 GHz Spectrum Analyzer using Atmega8 microcontroller There are plenty of wireless devices available on the
market that broadcast in the 2.4 GHz ISM band. Such devices include Bluetooth, WiFi, Zigbee, wireless USB, cordless phones,
wireless mice and keyboards, etc. This project describes a wireless spectrum analyzer to examine the surrounding radio…...
Listed under: AVR ATmega Projects, Internet - Ethernet - LAN Projects
1701. VGA monitor tester using ATTiny2313 microcontroller If you are a computer technician and want to avoid the need of a PC
on your desk to generate test rasters, this is something you need to build. This is an embedded monitor tester that you can
use to test if a VGA monitor…... Listed under: AVR ATmega Projects, Other Projects
1702. Digital oscilloscope GLCD using Atmega32 microcontroller This project describes how to make a digital oscilloscope using an
Atmega32 microcontroller and a graphics LCD. The GLCD used has 64*128 pixel dots (GDM12864A with KS0108 processor)
and the AVR runs at 16 MHz using an external crystal oscillator. To enhance the speed further,…... Listed under: AVR ATmega
Projects, Metering - Instrument Projects
1703. AM radio transmission using AVR using Atmega324 microcontroller When you think about building a radio transmitter
circuit, the first thing that comes in mind is it requires too many analog components. But wait a minute, this guy
demonstrates an AM transmission using a microcontroller. The interesting part is it uses a plant as…... Listed under: AVR
ATmega Projects, Radio Projects
1704. Open source color video game development system based on AVR This project describes an open source color game
development platform based on an AVR microcontroller. You can code a color, high resolution, smooth video game, like
Super Mario Bros or Commander Keen on this system. All video processing is done by software in background using…...
Listed under: AVR ATmega Projects, Video - Camera - Imaging Projects
1705. USB business card with a computer chip board using ATtiny85 microcontroller Have you ever seen a business card with a
computer chip embedded on it? This one does. It has an ATtiny85 microcontroller chip that stores all your personal details.
You plug it into an USB port of your computer, and find the details about the…... Listed under: AVR ATmega Projects,
1706. Experimental board using ATTiny2313 microcontroller This is an experimental board for ATTiny2313 microcontroller that
provides a 10-pin connector for in-circuit serial programming, and other header pins to access I/O pins. The AT2313
microcontroller runs on an external 10Mhz crystal. The board has a push button reset switch for resetting the…... Listed under:
AVR ATmega Projects, Development Board - Kits Projects
1707. Automate lights in your kitchen area using ATTiny84 microcontroller This project describes an automatic light system for
kitchen sink where you need sufficient light to properly clean your dishes and vegetables. It uses an ATTiny84 microcontroller
with a PIR motion sensor. When motion is detected, the microcontroller turns on the light. The light source…... Listed under:
AVR ATmega Projects, Home Automation Projects
1708. AVR displays body temperature on a Nokia 3310 LCD using Atmega8 microcontroller This project describes how to measure
temperature with Atmega8 and a thermistor and display it on a Nokia 3310 LCD. A thermistor is a device that changes its
resistance with temperature. With a proper resistor divider network, the temperature can be measured by measuring the…...
Listed under: AVR ATmega Projects, Phone Projects
1709. Open Source USB AVR Programmer for Students and Hobbyists using Atmega8 microcontroller If you cannot afford to buy a
USB programmer for AVR, don’t worry, you can make one by yourself. This programmer uses a Atmega8 microcontroller with
a few external passive components. The good thing is you don’t need any USB controller because it is implemented…... Listed
1710. AVR based remote controlled fan regulator This project is from Extreme Electronics that describes an AVR-based (Atmega8)
remotely controlled fan regulator. The control commands are received through a DVD player remote control. With three
buttons on the remote control, you can turn the fan On and Off and also conotrol the…... Listed under: AVR ATmega Projects,
Video - Camera - Imaging Projects
1711. 50 MHz range frequency counter using ATtiny45 microcontroller A wide range frequency meter is an useful tool for an electronics lab. This projects
describes a frequency meter based on AT90S231 microcontroller that can measure input frequencies up to 50 MHz. The measured frequency is
displayed on 6 digit multiplexed seven segment displays. It…... Listed under: AVR ATmega Projects

1712. Easy Data Logger with Virtual USB using ATtiny45 microcontroller “V-USB is a software-only implementation of a low-speed
USB device for Atmel’s AVR® microcontrollers, making it possible to build USB hardware with almost any AVR®
microcontroller, not requiring any additional chip.” For further details on V-USB and licensing, visit
http://www.obdev.at/products/vusb/index.html This is a data logger…... Listed under: AVR ATmega Projects, Interfacing(USB -
1713. Tetris and Snake with one AVR using Atmega168 microcontroller This project describes two games – Tetris and Snake, both
programmed inside an Atmega168 microcontroller. You can plug this device to a PAL TV and have fun playing the games.
The circuit diagram is very simple and uses resistors to generate composite video output. For…... Listed under: AVR ATmega
Projects, Game - Entertainment Projects
1714. Build an AVR Xmega Prototyping Board using AVR microcontrollers The AVR ATXmega chip is a newer offering in Atmel's AVR
line. The Xmega is billed as a hybrid 8/16-bit MCU, which means you can use your normal development environment to
program Xmegas (as compared to AVR32 and Atmel's ARM line). Because the Xmega uses…... Listed under: AVR ATmega
Projects, How To - DIY - Projects
1715. Development Board With LCD using Atmega16 microcontrollers This instructable shows, how to do your own development
board for Atmega16 or Atmega32 processors.The Internet is full of home made development boards, but I think that, there is
room left for another one. This board have been very useful on my projects and I…... Listed under: AVR ATmega Projects,
1716. Blinking, Singing, Marioman using Attiny microcontrollers Use an attiny13a, two LEDs and a greeting card speaker to create a
blinking Marioman that plays the Super Mario Brothers theme song. This can be an easy low-cost project for anyone who is
looking for a fun way to break into AVR programming! The…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1717. Reading Switches with using Attiny microcontrollers There have been several Instructables dealing with outputs from the
ATtiny2313 and similar AVR devices. For example, http://www.instructables.com/id/Ghetto-Programming%3a-Getting-
started-with-AVR-micro/, http://www.instructables.com/id/Drive-a-Stepper-Motor-with-an-AVR-Microprocessor/. Working on
the latest one from The Real Elliot, which showed how to control stepper motors, I found that it would be really helpful to
be…... Listed under: AVR ATmega Projects, Other Projects
1718. Halloween Robot using Attiny microcontrollers Halloween Robot controlled by an old wingman joystick. I don't reccommend
this for beginners with electronics only because some things like joysticks and power adapters are not all the same and must
be modified. Additionally I provide programming code which will only be useful for…... Listed under: AVR ATmega Projects,
1719. The simple joule thief using AVR microcontrollers The Joule Thief is such an easy and simple device, but what it does is
amazing. It can use a battery that is not usable in any other electronic device and give it life again. It can even take a battery
that won't even power…... Listed under: AVR ATmega Projects, Battery Projects
1720. ISP Breadboard Header using AVR microcontrollers When I was first working with AVR microcontrollers, I relied a lot on
tutorials I found on the web, but nearly all of them raised the question of how to attach a programmer to the microcontroller
when you aren't using a development board. Most of the time,…... Listed under: AVR ATmega Projects, Interfacing(USB -
1721. Portal "Still Alive" on using ATMega16 microcontrollers Yet another Portal-related instructable , but Different ! This one shows
you how to : 1)Build a very cheap device that plays an 8-bit version of Still Alive from Portal 2)On the same hardware , but
with a different chip , play the "radio tune"…... Listed under: AVR ATmega Projects, Radio Projects
1722. Atmega8 measures ambient temperature and relative humidity using HSM-20G sensor In one of my previous posts, I
discussed about Sensirion’s SHT11 and SHT75 sensors, which are capable of measuring both temperature and relative
humidity. They are digital sensors and provide fully calibrated digital outputs for temperature and relative humidity. I also
illustrated how to interface those…... Listed under: AVR ATmega Projects, Temperature Measurement Projects

1723. A complete starter guide to AVRs using attiny2313 microcontroller Have you played with Arduino's and now have a taste for
microcontrollers? Have you tried to go beyond Arduino but got stopped by the dense datasheets? This is the instructable for
you! I was working on an instructable for the epilog contest which would wirelessly…... Listed under: AVR ATmega Projects,
Other Projects
1724. An universal programming adapter for the Atmel STK500 using AVR microcontroller You have an STK500 development board
for the AVR controllers from Atmel? And you want to use it with a newer AVR controller which is not supported by any of the
8 sockets on board? And you do not own an STK505 extension board? Welcome…... Listed under: AVR ATmega Projects,
Development Board - Kits Projects, LED Projects
1725. Building a digital light meter with a calibrated LDR using Atmega8 microcontroller Measurement of light intensity is a prime
necessity in several occasions. The diversity of such needs make their way to various branches of physics and engineering as
well as in media. For instance, in engineering, such kinds of measurements are needed to design optimum lighting…... Listed
1726. Intelligent temperature monitoring and control system using AVR microcontroller Controlling temperature has been a prime
objective in various applications including refrigerators, air conditioners, air coolers, heaters, industrial temperature
conditioning and so on. Temperature controllers vary in their complexities and algorithms. Some of these use simple control
techniques like simple on-off control while others use…... Listed under: AVR ATmega Projects, Temperature Measurement
Projects
1727. AVR acoustic spectrum analyzer using Atmega8 microcontroller AVR acoustic spectrum analyzer, based on Atmega8 AVR
microcontroller, operational amplifier, and few other components. Use any HD44780 compatible LCD or VFD, connect audio
signal, and enjoy the effect You can build in this into your amplifier, pc, car-audio, or other device. On this…... Listed under:
AVR ATmega Projects, Microcontroller Programmer Projects
1728. Wireless Accelerometer Controlled rgb-LED's using atmega168 microcontroller MEMS (Micro-Electro-Mechanical Systems) Accelerometers are in
widespread use as tilt-sensors in mobile phones and cameras. Simple accelerometers are available both as ic-chip's and cheap development pcb-
boards. Wireless chips are also affordable and available in assembled circuits, with matched antenna-network and decoupling-caps onboard. Hook
both wireless…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN Projects
1729. Mini RGB Light Cube using AVR microcontroller This is basically a knockoff of the Hypnocube, instead of being 64 LEDs, thus
costing at least $150 to make, I made a smaller version of 8 LEDs for under $30. The result is a 2x2x2 cube where each light is
independently controllable. I'm not…... Listed under: AVR ATmega Programmers, AVR ATmega Projects, LED Projects
1730. Control Anything with one AVR pin using Attiny2313 microcontroller This instructable shows how to control a group of led's
with one microprocessor output. The micro I will be using is an Atmel Attiny2313. Step: 1 Parts and Tools Parts: Attiny2313
(got 5 free samples from Atmel) 20 pin socket Resistors (any size will work,…... Listed under: AVR ATmega Projects, Other
Projects
1731. Color Sensor using Atmega16 microcontroller This is a simple color sensor using Atmega16 MCU and can sense Red ,Green and Blue color. How it
works: the sensor consist from LDR sensor and RGB LED ,so when the object putted on the sensor the light that emitting from RGB LED will reflected
from the object to…... Listed under: AVR ATmega Projects, Sensor - Transducer - Detector Projects
1732. Ambient Light Gift Badge using ATTiny13 microcontroller After Christmas I was in the situation that my nephew's birthday
celebration came near. I asked him if he had a special on his wish list and he told me that he doesn't have a wish at all, for
the moment. He still had not…... Listed under: AVR ATmega Projects, LED Projects
1733. 3 Easy Holiday Gifts using ATTiny microcontroller Every year the holiday season rolls around and I get stuck on what to give
for my friends and family. People always say that it's better to make the gift yourself than buy it at a store so this year I did
just that. The…... Listed under: AVR ATmega Projects, LED Projects
1734. YAFLC (Yet Another Flickering LED Candle) using Tiny45 microcontroller There are numerous posts on Instructables about
how to make a flickering LED candle. This is my version. The project requires the following components: 1. Tiny45 AVR
Microcontroller (Tiny13 would also do) 2. 1W Warm white (or yellow) LED 3. Perspex tube 4. AA or…... Listed under: AVR
ATmega Projects, Home Automation Projects
1735. Rechargeable Battery Capacity Tester using ATMega168 microcontroller Do you have a pile of AA rechargeable batteries in
your drawer? Some are old, some are new, but which sets would you bring with your camera on your next trip, and which
ones are past their useful life? I like using rechargeable batteries, but…... Listed under: AVR ATmega Projects, Battery Projects
1736. Power your Arduino/AVR with a Hand-Cranked Battery using ATmega8 microcontroller If you've ever wanted to power your Arduino or AVR from a
battery for development testing (batteries have different power delivery qualities than, say, transformed AC or even a regulated wall wart in DC)

testing but were tired of going through batteries (Hey, I admit…... Listed under: AVR ATmega Projects, Battery Projects
1737. Arduino FTDI Header using ATmega8 microcontroller So, you want to program a bootloaded AVR. Or possibly, you have an
Arduino Lilypad and no way to program it. There are a few solutions available to you: You could buy a USB to FTDI adapter
(available at Adafruit, Sparkfun, etc), you could buy…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects
1738. Autonomus Wall Following Obstacle Avoiding Arduino Rescue Bot I'm an Electrical Engineering major and each year my
college's branch of IEEE competes in a student hardware competition. Last year's competition was inspired by the natural
disasters in Haiti and Chile (the competition was held one week after the earthquake in Japan). This was…... Listed under: AVR
ATmega Projects, Robotics - Automation Projects
1739. How to use a 74HC595 Shift Register with a using AVR ATtiny13 microcontroller If you have been playing with
microcontrollers and electronics then you have likely seen LED dot matrix displays and other projects that use shift registers
like 7-segment displays and more. This instructable goes over a quick intro to the 74HC595 8-Bit Serail to Parallel Shift…...
Listed under: AVR ATmega Projects, How To - DIY - Projects
1740. $10 ATtiny85/45 POV display!! (works really well) Hey guys! This is an Instructable for making your own ATtiny85/45 5 LED
POV (Persistence Of Vision) display! This is my second Instructable, also for the Elemental LED contest, so drop a comment
and vote it up! The total parts cost for this POV display…... Listed under: AVR ATmega Projects, LED Projects, Video - Camera -
Imaging Projects
1741. The $9 Quasi-duino (Almost-duino) using ATmega328 microcontroll Do you currently have an Arduino and want to make it
smaller for cheap? The Quasi-duino is for you (Italian for almost-duino). This makes a functional "almost" Arduino, in a very
small form factor using the narcoleptic library for pico-power operations on a pico-space breadboard.…... Listed under: AVR
ATmega Projects, Other Projects
1742. Soldering an SMT MOSFET Driver with a hotplate using microcontroller Soldering SMD components isn't as hard as you
might think. In fact it's easy. If you follow this instructables you'll soon see just what great results you can obtain at home
using just a hotplate. It's not just being able to make small circuit boards…... Listed under: AVR ATmega Projects, PWM
Projects
1743. $1.50 Arduino TV Annoyer!! (Turns TVs on when you want them off) using microcontroller Hey Arduino fans! Here is an 'ible
for making a device that turns TVs on when you want them off, and off then you want them on! If you hide it in something
inconspicuous, it would make a great April Fools joke or gag gift.…... Listed under: AVR ATmega Projects, Video - Camera -
Imaging Projects
1744. Programming Arduino Bootloader without Programmer using ATmega168 microcontroller OH NO!!! You've screwed up and
now the Arduino bootloader on your 'duino is gone! What are you going to do? Go spend money for a programmer??? Well
don't! I've got a solution that only requires your 'duino and some wires! So its not the…... Listed under: AVR ATmega Projects,
1745. Music Playing Alarm Clock using ATmega644 microcontroller This Instructable will be about designing a music player from
using various building blocks. You will understand the communication between the microcontroller, memory, computer, LCD
display, RTC, IR remote, and the music file decoder. I will try my best to to teach you in a…... Listed under: AVR ATmega
1746. Door Activated LED Lighting using Hall Effect Sensors using Attiny85 microcontroller I've been meaning to make something
cool for my dorm room this coming semester and decided that some custom closet lights would look great. In this
Instructable, I'll show you how to make some nice-looking LED lights that will turn on automatically using a hall…... Listed
under: AVR ATmega Projects, Home Automation Projects
1747. Getting Started with Atmel AVR and BASCOM using attiny26 microcontroller I have seen plenty of Instructables showing how
to work with microprocessors, but they all assume that you have worked with them before and know what you are doing. I
have not seen an Instructable that takes you from nothing and builds on each step.…... Listed under: AVR ATmega Projects,
Other Projects
1748. How to use the Dragon Rider 500 with your AVR Dragon using ATtiny2313 microcontroller This instructable is a crash course in how to use some of
the features of the Dragon Rider 500 from Ecros Technologies. Please be aware that there is a very detailed User's Guide available on the Ecros
website. The Dragon Rider is a interface board…... Listed under: AVR ATmega Projects, Microcontroller Programmer Projects

1749. Make a breadboard adapter for your AVR microcontroller using attiny2313 If you like to play around with micro controllers
you know this hustle: You want to test a part of a program and first you need to completely wire up the uC on the bread
board. Not with these handy parts any more! These are…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1750. How to program a AVR (arduino) with another arduino using attiny2313 microcontroller * you've got your arduino with
atmega168 and you bought an atmega328 at you local electronics store. It doesn't have an arduino bootloader * you want to
make a project that doesn't use arduino - just a regular AVR chip (like the USBTinyISP) - you…... Listed under: AVR ATmega
Projects, How To - DIY - Projects
1751. Creating a charlieplexed LED grid to run on ATTiny85 This instructable was inspired by my first AVR microcontroller project
that I've been working on for some time now. I wanted to start learning more about the AVR microcontroller and see how
much I could do with the minimum amount of hardware... no extra chips,…... Listed under: AVR ATmega Projects, LED Projects
1752. How to control a 16×2 LCD using an AVR ATtiny2313 If you are just getting into microcontrollers there's alot to know as you
have likely found out. There's alot of good online tutorials for the Atmel AVR's and chances are you have see a few of those
by now. I recently got into microcontrollers and…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
1753. How to program a AVR (arduino) with another arduino using atmega168 microcontroller This instructables is usefull if: *
you've got your arduino with atmega168 and you bought an atmega328 at you local electronics store. It doesn't have an
arduino bootloader * you want to make a project that doesn't use arduino - just a regular AVR chip…... Listed under: AVR
ATmega Projects, How To - DIY - Projects
1754. Singing Pumpkins/ Arduino using microcontroller Lets start off by saying that I am a noob to micro controllers like Arduino.
After looking through instructables for a while I saw the things that arduino could do. That is when I realized that I had to get
one and learn the whole…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1755. Turn a TV-B-Gone into a super camera remote! Intro: My Nikon DSLR has an infrared remote function (remote sold
separately) that is really handy, but fairly limited in range. A while ago, I bought a TV-B-Gone Kit from it's inventor Mitch
Altman, and it can turn TV's off from a great distance. I…... Listed under: AVR ATmega Projects, Video - Camera - Imaging
Projects
1756. Vintage Toothbrush Timer using ATMega328p My last visit to the dentist convinced me that I should really brush my teeth at
least two minutes. I decided to build a special toothbrush timer: it would detect when a brush is taken out, measure two
minutes and notify when the time is…... Listed under: AVR ATmega Projects, Medical - Health based Projects
1757. Custom Tron Disc Mod using ATMega328 In this Instructable, I cover modding the store-bought Deluxe Identity Disc to an
upgraded version with 64 leds, controlled by an AVR MCU. The upgraded version is costume-ready and would be an
excellent addition to your Tron costume - it'll also look great on your…... Listed under: AVR ATmega Projects, Other Projects
1758. Build Your Own BARBOT using AVR microcontroller Ever wanted a robotic liquor server?I purchased a Lynxmotion robotic arm
last year and an Arduino (deci) to play around with. I had it serial controlled with a joystick and it was a great way to start in
robotics. More recently I wanted to take…... Listed under: AVR ATmega Projects, Robotics - Automation Projects
1759. Ard-e: The robot with an Arduino as a brain using microcontroller Hopefully after reading this instructable you will be able to
take your first step into robotics. Ard-e cost about $90 to $130 depending on how much spare electronics you have lying
around. The main costs are: Arduino Diecimella- $35 https://www.makershed.com/ProductDetails.asp?ProductCode=MKSP1
Bulldozer kit- $31 http://www.tamiyausa.com/product/item.php?product-id=70104 Servo-…... Listed under: AVR ATmega
Projects, Robotics - Automation Projects
1760. Turn signal biking jacket using microcontroller This tutorial will show you how to build a jacket with turn signals that will let people know where you're
headed when you're on your bike. We'll use conductive thread and sewable electronics so your jacket will be soft and wearable and washable when
you're…... Listed under: AVR ATmega Projects, Game - Entertainment Projects

1761. The 74HC164 Shift Register and your Arduino using GD74HC164 microcontroller Shift registers are a very important part of
digital logic, they act as glue in between the parallel and serial worlds. They reduce wire counts, pin use and even help take
load off of your cpu by being able to store their data. They come…... Listed under: AVR ATmega Projects, How To - DIY -
Projects
1762. Using a Dot Matrix LED with an Arduino and Shift Register The Siemens DLO7135 Dot matrix LED is one amazing piece of
optoelectronics. It's billed as a 5x7 Dot Matrix Intelligent Display (r) with Memory/Decoder/Driver. Along with that memory,
it's got a 96-character ASCII display set with upper and lower case characters, a built-in character generator…... Listed under:
AVR ATmega Projects, How To - DIY - Projects
1763. Arduino EMF (Electromagnetic Field) Detector A while back I saw an EMF (Electromagnetic Field) Detector at makezine.com
that used a led bargraph. I decided to modify it to use a 7-Segment LED Display! Here's my project. Sorry I don't have any
pictures of it in use. Hopefully I can post…... Listed under: AVR ATmega Projects, Sensor - Transducer - Detector Projects
1764. Arduino magnetic stripe decoder using microcontroller This instructable shows how to use some freely available code, an
arduino, and a standard magnetic stripe reader to scan and display the data stored on magnetic stripe cards such as credit
cards, student IDs, etc. I was inspired to post this after reading the…... Listed under: AVR ATmega Projects, Memory - Storage
Projects
1765. Arduino XMAS hitcounter using AVR microcontroller Christmas is coming closer, so here is my contribution to put you in the
right mood. It is a blog hitcounter, that rings a bell. Literally. It puts a smile on your face, every time someone hits your blog.
It consists of an Arduino board,…... Listed under: AVR ATmega Projects, Game - Entertainment Projects
1766. The Lightning Simulator/Breathalyzer/Graphic Equalizer – Using Arduino Powered The LED strips are mounted on an outdoor
trellace which functions as a lightning simulator, outdoor breathalyzer, graphic equalizer synced to music, and a few other
effects with sound. Materials: 8 12v RGB Waterproof Flexible LED Strips 10ft long (usledsupply.com) - $800 8 RGB 4A/Ch
Amps…... Listed under: AVR ATmega Projects, Home Automation Projects, LED Projects
1767. Make a Web Connected Robot (for about $500) (using an Arduino and Netbook) This Instructable will show you how to build
your own Web Connected Robot (using an Arduino micro-controller and Asus eee pc). Why would you want a Web
Connected Robot? To play with of course. Drive your robot from across the room or across the country,…... Listed under: AVR
ATmega Projects, Internet - Ethernet - LAN Projects, Robotics - Automation Projects
1768. Interfacing ATmega32 with an LCD and a DAC Hi techies!! This is one more of my circuits, interfacing ATmega32 with an LCD
and a DAC. it also includes two general purpose push-buttons and In System Programming connector. The controller is
operating with 14.7456 MHz frequency crystal, convenient for generating standard baud rates (for…... Listed under: AVR
ATmega Projects, How To - DIY - Projects, LCD Projects
1769. Arduino and Touchpad Tic Tac Toe using microcontroller Or, an exercise in input and output multiplexing, and working with bits. And a submission for
the Arduino contest. This is an implementation of a tic tac toe game using a 3x3 array of bicoloured LEDs for a display, a simple resistive touchpad,
and an…... Listed under: AVR ATmega Projects, Game - Entertainment Projects

1770. The 4x4x4 LED cube (Arduino) In this instructable I will show you how to make a 4x4x4 LED cube that will be controlled by an
Arduino Demulionove. now yes you might say" that Arduino has only 14 I/O pins well also the 6 analog pins can be used as
pins…... Listed under: AVR ATmega Projects, LED Projects
1771. Arduino Laser Tag – Duino Tag Duino tagger- General introduction Duino tag is a laser tag system based around the arduino.
Finally a laser tag system that can be tweaked modded and hacked until you have the perfect laser tag system for office
ordnance, woodland wars and suburban skirmishes. Laser tag…... Listed under: AVR ATmega Projects, Other Projects
1772. Ardu-pong! the Arduino based pong console A while back the instructables robot made a post on Facebook about some
guys who played pong on an Arduino (http://wayneandlayne.com/projects/video-game-shield/games/#pong) but after
looking around, i saw that everyone who did this was only worried about making it work. and often resulted as a very hard…...
Listed under: AVR ATmega Projects, Game - Entertainment Projects
1773. How to make a multi-layered acrylic and LED sculpture with variable lighting levels Here you can find out how to make you
very own n as made for the exhibition www.laplandscape.co.uk curated by art/design group Lapland. More images can be
seen at flickr This exhibition runs from Wednesday 26 November - Friday 12 December 2008 inclusive, and had…... Listed
under: AVR ATmega Projects, How To - DIY - Projects, LED Projects
1774. Garduino Upgrade, Now with more Twitter! A couple months ago I came across two great instructables. The first was the
Garduino, an arduino controlled garden to help you grow plants at home. The second was the Tweet-a-Watt, a project that
teaches you how to monitor your home power usage using Xbees…... Listed under: AVR ATmega Projects, Internet - Ethernet -
LAN Projects
1775. Garduino: Gardening + Arduino Garduino is a gardening Arduino. So far, Garduino: -Waters my plants whenever their soil
moisture level drops below a predefined value. -Turns on grow lights, but only when it's dark out and only long enough to
make the plants get 15 hours of total light…... Listed under: AVR ATmega Projects, Development Board - Kits Projects
1776. Control a Schlage electronic deadbolt with an arduino! This instructable will walk you through the process of dismantling and
hacking a Schlage electronic deadbolt in order to control it with an arduino. Step 1 Purchase the lock and unpack it I got
mine on sale for $99 at Lowe's. Remove it from the…... Listed under: AVR ATmega Projects, Other Projects
1777. The Arduino Weather Station / Thermostat using ATmega328 microcontroller I've always been interested in monitoring my
local weather, and noticed the difference between what weather.com and accuweather.com think my local weather is, and
what I see out the window. I also wanted better control over my heating and A/C system. As a computer and…... Listed under:
AVR ATmega Projects, Sensor - Transducer - Detector Projects, Temperature Measurement Projects
1778. Arduino All-in-One Getting Started Guide An all-in-one tutorial to getting started with the Arduino open-source electronics prototyping platform. This
guide is meant for the beginner but should be also be useful to you if you already tinker with electronics but want to get started with the Arduino. I'll

cover: -…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1779. Arduino Powered Binary Clock using ATmega168 microcontroller This instructable will help you to build an Arduino Binary
Clock. The orignial idea for this instructable was designed by Daniel Andrade. My instructable uses surface mount
components, but can easily be adapted to through-hole components if you wish. You can follow my other Instructable…...
Listed under: AVR ATmega Projects, Clock Projects
1780. Interface a rotary phone dial to an Arduino An old rotary phone can be used for a number of purposes in your Arduino
projects - use it as a novel input device, or use the Arduino to interface a rotary phone to your computer. This is a very basic
guide describing how to…... Listed under: AVR ATmega Projects, Phone Projects
1781. Digital Window Sticker (Arduino Controlled) using ATMega328 microcontroller A bumper-sticker sized L.E.D. matrix that
displays images in sequence from an SD card, to produce an animated sign or "window sticker." Arduino controlled! Also
includes Windows, Mac, and Linux code for converting .xbm image files into Digital Window Sticker files. Perfect for a
shop…... Listed under: AVR ATmega Projects, Other Projects
1782. Arduino Watch Build Instructions The Arduino Watch provides augmented sensing of temperature and range, 16-bit color
drawing program, Breakout game, and also tells the time in your choice of digital, binary, or analog. Additional sensors,
devices, and programs are easy to add as any standard Arduino. The source code…... Listed under: AVR ATmega Projects,
Clock Projects
1783. Mushroom Environment Control – Arduino Powered This is my first Arduino project aimed at helping me with my other
hobby which is growing oyster and shiitake mushrooms indoors. In a nutshell, the controller takes in two temperature
readings, 1 Humidity reading and 1 Co2 reading and triggers a set of four…... Listed under: AVR ATmega Projects, Medical -
Health based Projects
1784. How to connect Arduino and RFID On this instructable I will try to show how to interface a RFID sensor with the Arduino. I am
using the RFID sensor from seeedstudio the serial version of it. There are a few parts you will gonna need. I also bought some
RFID keys.…... Listed under: AVR ATmega Projects, How To - DIY - Projects, RFID - NFC Projects
1785. How To Smell Pollutants This Instructable explains how to use a gas sensor with your Arduino. This lets your Arduino smell
(and hence you program responses to) overall gas levels for a variety of nasties, including ethanol, methane, formaldehyde,
and a bunch of other volatile organic compounds. My cost…... Listed under: AVR ATmega Projects, Sensor - Transducer -
Detector Projects
1786. Temperature Control For Kitchen Appliances In this Instructable, I will step through controlling the temperature of most
kitchen appliances. As an example, I will use an old Westbend Poppery popcorn maker (aka. coffee roaster), but these same
techniques will be applicable to most hot plates, coffee makers, and waffle irons.…... Listed under: AVR ATmega Projects,
1787. Wireless Altoids Display This Instructable will show you how to modify an Altoids tin for a wireless 2x16 character display. Using an Altoids tin was
inspired by the need to have a small yet protective enclosure for a pair of Xbee modules recently bought from Sparkfun. I purchased the…... Listed
under: AVR ATmega Projects, Internet - Ethernet - LAN Projects

1788. Secret Knock Detecting Door Lock Protect your secret hideout from intruders with a lock that will only open when it hears the
secret knock. This started out as a bit of a joke project, but turned out to be surprisingly accurate at judging knocks. If the
precision is turned all…... Listed under: AVR ATmega Projects, Security - Safety Projects
1789. Gmail and RSS Notifiers using the Arduino I’ve been really interested in doing J4mie’s Physical Gmail Notifier ever since it
came out in February. I only recently dropped into the project and got to learn a lot about python, plists, and arduino auto-
reset functionality. I’m going to share what I’ve learned because…... Listed under: AVR ATmega Projects, Sensor - Transducer -
Detector Projects
1790. Magnetic Levitation using the Arduino It’s been only a couple weeks since I discovered Arduino, an open source
microcontroller platform. I was looking for a cheap interface between my laptop and electronic circuits. Arduino with its price
$35 and easy to use development environment was the best choice. So after…... Listed under: AVR ATmega Projects, Sensor -
1791. Wi-Fi Enabled Coil Gun with iPhone App We’ve covered loads of airsoft, nerf, and gun projects, and here’s another superb
pr0ject to add to our collection. It’s a coil gun placed on a turret which is triggered via Wi-Fi. Additionally, it uses remote
targeting and shooting through an iPhone, iPod Touch or…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN
Projects, Phone Projects
1792. Superb DIY Retro Lighting Design What is it? It is a decorative lamp; a very, very impractical decorative lamp employing a few
vintage display devices and a couple of LEDs too. A friend of mine was one of a group of artists who produced Ascension
(the giant origami-crane tent) at…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1793. A credit card sized Ethernet Arduino compatable controller board using ATmega168 microcontroller I love the Arduino as a
simple and accessible controller platform for many varied projects. A few months ago, a purchased an Ethernet shield for my
Arduino controller to work on some projects with a mate of mine - it was a massive hit -…... Listed under: AVR ATmega
Projects, Internet - Ethernet - LAN Projects
1794. Light for life: Glowing button cycling jacket Not everyone wants to look like an athlete while cycling to work or school. This
cycling-jacket, made of hemp and wool, is equipped with lots of shining bright LEDs. It looks just as good during the day as it
does during the night. Embedding the…... Listed under: AVR ATmega Projects, Game - Entertainment Projects
1795. The Word Clock – Arduino version using ATMega168 microcontroller Major updates - A much better enclosure for this clock
has been designed - check out http://www.instructables.com/id/The-Wordclock-Grew-Up/ Last month I wanted to build a
special gift for my beautiful wife, Megan. She has a teaching background in English, so what better present to make for…...
Listed under: AVR ATmega Projects, Clock Projects, LED Projects
1796. Arduino R/C Lawnmower (painted) using Atmega168 microcontroller What this is: This instructable will show you how to
make your Arduino into an R/C interface that you can use for just about anything requiring remote control. I will also show
you how I built an R/C lawnmower using my Arduino, a cheap R/C transmitter and…... Listed under: AVR ATmega Projects,
1797. How to have fun with Arduino (and become a Geek in the process) Do you wish to earn your geek card - pronto? Lets get
started! This guide will start you on the path to the dark side using the open source Arduino development and prototyping
platform. It will introduce you to microcontrollers, get you started with a…... Listed under: AVR ATmega Projects, How To - DIY
- Projects
1798. Control Electronics using an Arduino and Infrared LEDs Learn how to use infrared LEDs to send signals to your TV and other
electronic devices via an Arduino. First, the Arduino will interpret IR pulses sent out by the TV remote, save them to memory,
then “replay” them upon the user’s command. You can…... Listed under: AVR ATmega Projects, LED Projects, Other Projects
1799. Arduino animatronics- make your awesome costumes more awesome! using ATmega328 microcontroller Here's how to add lights, sound and action
to your favorite Halloween project using the open source Arduino microcontroller. Arduino is easy to learn to use and it opens up a whole new world

for costume builders and creature creators. If you want to learn…... Listed under: AVR ATmega Projects, Sound - Audio
Projects
1800. Using the iRobot Create's Command Module with Linux using avr microcontroller Since iRobot hasn't provided linux users
with a way to use the command module, I had to figure it out myself. Don't be intimidated, its not hard at all, really. All you
need to do is run a couple of scripts. Lets get started, shall…... Listed under: AVR ATmega Projects, Microcontroller
Programmer Projects, Robotics - Automation Projects
1801. Use Visual Studio 2010 to Compile AVR Hex Files using AVR microcontroller I'm not a huge fan of Microsoft, but man, they do
make one slick programming IDE. In searching around for a solution to use the IDE to program AVR's I came across some
scattered instructions. As I love the intellisense feature of Visual Studio (VS)…... Listed under: AVR ATmega Projects,
1802. Laser Tripwire takes a Photo, Uploads it to Twitter This instructable will show you how to construct a laser tripwire that can
twitter and grab an image from a webcam, as well as execute any command you can put in a bash script. This instructable is
actually quite simple and is even suitable as a beginner…... Listed under: AVR ATmega Projects, Video - Camera - Imaging
Projects
1803. The Household Informer using atmega168 microcontroller Who wants to go outside to see if the mail has arrived? In the cold
winter or rain I’d rather not have to put on a jacket and shoes, only to find that there was no mail. This project will notify you
of the mail…... Listed under: AVR ATmega Projects, Home Automation Projects
1804. The $9 Quasi-duino (Almost-duino) Do you currently have an Arduino and want to make it smaller for cheap? The Quasi-
duino is for you (Italian for almost-duino). This makes a functional "almost" Arduino, in a very small form factor using the
narcoleptic library for pico-power operations on a pico-space breadboard.…... Listed under: Circuits
1805. Turn Your Arduino Into an ISP Learn how to turn your Arduino into an AVR In System Programmer. This will allow you to burn
bootloaders onto new chips or program AVRs without a bootloader. Step 1: Materials To begin you will need: * Arduino (I will
be using the Uno) *…... Listed under: AVR ATmega Projects, Video - Camera - Imaging Projects
1806. GuGaplexed Valentine LED Heart using ATTiny13V Microcontroller GuGaplexing is a new LED display multiplexing technique.
Compared to Charlieplexing, GuGaplexing allows you to control twice as many LEDs, with just a few additional components.
GuGaplexed Valentine LED Heart project has 40 LEDs arranged in an 'Arrow Piercing a Heart" arrangement using only 5…...
Listed under: AVR ATmega Projects, Game - Entertainment Projects, LED Projects
1807. Smoke & Fume Absorber Demo video Smoke & Fume Absorber A Long History The ancient Egyptians produced lead and
other important metals like gold and silver as early as 5000 BC. In the Roman era, lead was used for coinage, jewelry and
other everyday items including the production of…... Listed under: AVR ATmega Projects, Other Projects
1808. Use Google Voice Search through Arduino & Bluetooth With Google announcing the launch of Voice Search for desktop, we
couldn’t help thinking that there was even more fun to be had with talking to a computer. So, we went ahead and built an
open source dev board to inspire people to build their…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN
Projects
1809. Arduino powered hangman giftbox/lockbox using ATmega328 microcontroller A medium sized box that requires the user to
succeed in a game of hang man in order to gain access to the contents of the box. Great gift Idea!!! my Arduino sketch will
be included in this instructible sorry for the poor quality pictures!…... Listed under: AVR ATmega Projects, Game -

1810. Beginner's Guide – AVR Programming You will get this done in 30 min. Step 1: Parts 1. 1 X any type of circuit board 2. 1 X
Atmel AVR Atmega16 microcontroller 3. 8 X 330 ohms Resistors 4. 8 X LEDs 5. 1 X AVR Programmer (just use for download…...
1811. Assembling the ZIFduino USB 1.2 using ATMEGA168 microcontroller The ZIFduino, for all intents and purposes, is an Arduino
with a ZIF socket. It's geared toward those that want to do prototyping on the platform, but then move the ATMega chip to a
stand-alone environment. The pin layouts are exactly the same, so it…... Listed under: AVR ATmega Projects, How To - DIY -
Projects
1812. Assembling the Dragon Rider 500 for use with the AVR Dragon using ATmega88 microcontroller Not long ago the Atmel
company came out with a great tool for use with the AVR line of microcontrollers called the AVR Dragon. This small USB
device provides professionals and hobbyists alike the ability to use: In System Programming (ISP), JTAG, Debug Wire, and…...
Listed under: AVR ATmega Projects, RTOS - OS Projects
1813. Fun Hackable Speaker Timer using ATMega328 microcontroller This is a fun speaker timer I made for some upcoming
conferences. It uses a 4-digit charlieplexed LED (pseudo 7-segment) display and is driven by a AVR ATMega328 or an
Arduino. It allows a default time to be set, can be paused, and will put…... Listed under: AVR ATmega Projects, Sound - Audio
Projects
1814. Slaveflash with Attiny24 ver. 2.0 You might have noticed the Slaveflash I built with an Attiny 24, the instructable can be found
here: Slaveflash-trigger-for-digital-with-Attiny24 After building the first prototype I collected all my old flashes I got over
the years and had four more slaveflash-triggers to built. I already figured…... Listed under: AVR ATmega Projects, Memory -
Storage Projects
1815. Getting started with LCD's and Microprocessors using ATmega8 In this Instructable, find out how to control LCD's with a
ATmega8 and Bascom. Demo You will need: - Breadboard - Wires - ATmega8 - Programmer - Bascom AVR (There is also a
demo version for Free) - 10k resistor - 100k resistor - 10k…... Listed under: AVR ATmega Projects, LCD Projects
1816. Programming adapter from 10 pin to 6 pin for AVRs This is the last one of my 'Things that make life easier' series, I published
in the last few days. It's very simple, but most of the time the simple things are the most helpful. I always used the big 10 pin
jack for programming…... Listed under: AVR ATmega Projects, Microcontroller Programmer Projects
1817. Direction Aware Messaging LED Spin Top using Tiny44 microcontroller We recently built a LED spinning top with message
display. Its an improved version of a similar top published by Elektor in their December 2008 issue. The Elektor top can be
spun only in one direction. The synchronization required to print message on the LEDs…... Listed under: AVR ATmega Projects,
LED Projects
1818. Annoying Beeper using Microcontroller ATtiny13 Play a prank on your friends (enemies?) by hiding a high-pitched beeper
which sounds off at random time intervals. This instructable uses minimal parts. All that is required is: battery microcontroller
speaker Why don't I just use a 555 timer chip? You certainly could. I…... Listed under: AVR ATmega Projects, Game -
1819. Open Source Temperature Controller- Appliance Heat Exchanger video Open Source Temperature Controller- Appliance Heat
Exchanger Here's a heat exchanger demo using the open source temperature controller. Full heat exchanger available here
Intelligent controller, schematics, and code available here The open source temperature controller allows you the flexibility to
control DC appliances based…... Listed under: AVR ATmega Projects, PWM Projects
1820. Instalacion del controlador USBasp (USBasp drivers setup) – Dark Side Electronics English version available at the bottom Se enseñara paso a paso
como instalar los controladores (drivers) necesarios para el correcto funcionamiento del programador USBasp para microcontroladores AVR. Primero,
mencionaremos algunas consideraciones para evitar fallos por usos indebidos del programador. También se mencionará el protocolo y…... Listed

1821. How to Read Binary/Hex Thumbwheel Switch with an AVR Microcontroller This instructable will show you how to read the
number on a binary pushwheel or thumbwheel switch using LED's or an AVR microcontroller (I'm using an ATmega328p but
this can be adapted for any AVR or probably another microcontroller of your choice). Multiple thumbwheel switches…... Listed
under: AVR ATmega Projects, How To - DIY - Projects
1822. DIY Digital Thermometer Using ATMega8 This instructable will show you how to make a thermometer that displays the
temperature of the air. It's not the most accurate thermometer in the world, but for this price and the fact that it was
homemade... This instructable will show you how to make…... Listed under: AVR ATmega Projects, Temperature Measurement
Projects
1823. Power Your Arduino From Your Car The Arduino -- and AVRs in general -- have a wide range of power supply options ranging
from around 1.8V to 5.5V. The choice of voltage is usually determined by the desired clock speed or power consumption
requirements. The Arduino and its many variants have…... Listed under: AVR ATmega Projects, Car Projects
1824. Build the Penguin game system using ATMega32/644 microcontroller Gotta love microcontrollers.They do lots of stuff ... you
can find them in computer mice , traffic lights , toys , and almost all electronic devices nowadays. Well , this is a project that
pushes an 8-bit ATMega32 microcontroller to the limits. As you guessed…... Listed under: AVR ATmega Projects, Game -
1825. Electronic Tic-Tac-Toe with RGB LEDs video Electronic Tic-Tac-Toe with RGB LEDs RGB LED game to play Tic-Tac-Toe for two
players. Uses 2 AVR Microcontrollers: Mega16 and Mega8. RGB LEDs allow each user to choose his/her color to represent
Cross/Nut. For more details, click: Electronic Tic-Tac-Toe with RGB LEDs... Listed under: AVR ATmega Projects, Game -
1826. Drive a Stepper Motor with an AVR Microprocessor using ATTiny2313 microcontroller Got some scavenged stepper motors
from printers/disk drives/etc lying around? Some probing with an ohmeter, followed by some simple driver code on your
microprocessor and you'll be stepping in style. Step 1 Get to Know Steppers Basically, you're going to need to figure out
where…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, Motor Projects
1827. Getting started with LCD's and Microprocessors In this Instructable, find out how to control LCD's with a ATmega8 and
Bascom. You will need: - Breadboard - Wires - ATmega8 - Programmer - Bascom AVR (There is also a demo version for Free) -
10k resistor - 100k resistor - 10k variable…... Listed under: AVR ATmega Projects, How To - DIY - Projects, LCD Projects
1828. Slaveflash-trigger for digital cameras with Attiny24 When flashing with digital compact cameras, the camera usually uses
several small flashes before making the actual picture. This is o.k. if the built-in flash is the only flash you have, but if you
want to use an external second flash you have a problem:…... Listed under: AVR ATmega Projects, Other Projects
1829. Apple-style LED pulsing using a $1.30 MCU using ATTiny85 microcontroller The Atmel ATTiny85 chip is an 8-pin MCU that is
totally awesome. If you've been programming with the bigger boys (the ATMega series), these are a nice adventure - you're
rather limited in the number of output pins, but a creative design gives us a…... Listed under: AVR ATmega Projects, LED
Projects

1830. Watch futurama on an 8×8 pixel screen using atmega168 microcontroller here's how to convert otherwise reasonable quality
video into pixelated garbage and play it on a 2 color 8x8 led matrix, with no sound and only moderate sync. ingredients: - (1)
8x8 2 color led matrix - (1) atmel avr atmega168 - (2) 74hc595 shift…... Listed under: AVR ATmega Projects, LCD Projects
1831. AVR/Arduino RFID Reader with UART Code in C RFID is the craze, found everywhere - from inventory systems to badge ID
systems. If you've ever been to a department store and walked through those metal-detector-looking things at the
entrace/exit points, then you've seen RFID. There are several places to find good information on…... Listed under: AVR
ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, RFID - NFC Projects
1832. How To Make A Grounding Wrist Band In my life i deal with lots of sensitive electronics every day and frying these electronics
is a big concern when touching them. Most people think its hard to fry electronics with static electricity. Its not, one touch
could send your $100 graphics card down…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1833. Telnet to your Arduino/AVR! The other day I was wanting to check on one of my AVR's but I was upstairs and god knows it
was too much of a hassle to go downstairs to where the microcontroller was. But, there were two idle computers sitting
upstairs next to…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN Projects
1834. A protective case for the Atmel AVR Dragon using AVR This instructable will show you how to easily modify a readily available
plastic case to hold and protect your AVR Dragon PCB. Atmel promotes their AVR Dragon as a low cost development product
tool for use with their AVR microcrontollers. While the product does come…... Listed under: AVR ATmega Projects,
1835. Ghetto Development Environment Using Microcontrollers A while back, I posted up a quick and dirty "el cheapo" method of
getting started programming the Atmel AVR series chips: Ghetto Programmer (version 1.0) Since then, I've vamped, re-
vamped, and otherwise improved my setup. Thought it'd be nice to document it. The goal…... Listed under: AVR ATmega
Projects, Microcontroller Programmer Projects
1836. USB RFID Reading Keyboard using USnooBie video USB RFID Reading Keyboard Demo This is a step by step tutorial on how
to build a RFID tag reading USB keyboard using the USnooBie. This tutorial is provided with the project files. The code files
are heavily commented with references to relevant…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects, RFID - NFC Projects
1837. New Jar of Fireflies When I ran across the Jar of Fireflies Instructable sometime this past summer, I knew I had to build it. Full
credit to Keso for an excellent set of instructions! I wouldn't have gotten to the point of developing the firefly behavior
without such a solid base for…... Listed under: AVR ATmega Projects, Game - Entertainment Projects
1838. FanBus Digital Fan and LED Interface for PC using ATMega168 microcontroller Last year I modified a blue LED fan with RGB
LED's to enhance the look of my server case. Last summer I built a gaming computer and ever since I wanted to light it up
with multiple controlled lights and fans. I finally figured out…... Listed under: AVR ATmega Projects, LED Projects
1839. Augmenting a Microcontroller using AVR Microcontrollers (MCUs) are fantastic little ICs that give an extra element of
versatility to your electronics, robotics or other project. But they're really not much use on their own. To function, all MCUs
need some sort of support components, and a board to live on…... Listed under: AVR ATmega Projects, Other Projects
1840. Development system for PIC and AVR microcontrollers After testing many systems development for PIC and AVR
microcontrollers, none satisfy me. So I created this system with breadboard that has satisfied me. Step 1: More space free In
this development system, I put two protoboards turned 180 degrees from each other. The space…... Listed under: AVR
ATmega Projects, Development Board - Kits Projects
1841. VUSBTiny AVR SPI Programmer Using ATtiny85 after making a usbtiny isp programmer and using it for 6 months, i was looking at making another one
for carrying around. i like the simplicy of the usbtiny isp design but would like to make it even smaller and take less parts. one thing…... Listed under:
AVR ATmega Projects, Other Projects

1842. Direction Aware Messaging LED Spin Top video Direction Aware Messaging LED Spin Top We recently built a LED spinning
top with message display. Its an improved version of a similar top published by Elektor in their December 2008 issue. The
Elektor top can be spun only in one direction. The synchronization…... Listed under: AVR ATmega Projects, LED Projects, Other
Projects
1843. Tiny AVR Microcontroller Runs on a Fruit Battery Some of the fruit and vegetables we eat can be used to make electricity. The
electrolytes in many fruit and vegetables, together with electrodes made of various metals can be used to make primary cells.
One of the most easily available vegetable, the ubiquitous lemon…... Listed under: AVR ATmega Projects, Battery Projects
1844. Fire-free LED Matchstick Using a Tiny13 microcontroller video Fire-free LED Matchstick I just completed a new project: a fire-
free and fire-safe LED matchstick. To light this matchstick you strike it against a normal matchbox filled with neodymium
magnets. The LED matchstick has an inductive sensor that detects the magnetic field as you…... Listed under: AVR ATmega
1845. How to use an LED Array Module using AVR With a single LED you can indicate the state of something: on or off. That might
be a little boring. With an array of LEDs you can display characters or even some simple blocky graphics. That might add a
little pizzaz to a small microcontroller…... Listed under: AVR ATmega Projects, LED Projects
1846. Programmable LED using Atmel ATtiny13v Microcontroller Inspired by various LED Throwies, blinking LEDs and similar
instructables I wanted to do my version of an LED controlled by a microcontroller. The idea is to make the LED blinking
sequence reprogrammable. This reprogramming can be done with light and shadow, e.g. you could…... Listed under: AVR
ATmega Projects, LED Projects
1847. Hacking your Digg Button with a Removable Interface Cable using AVR The Digg Button from adafruit industries
www.adafruit.com is a very simple DIY electronics kit suitable for beginners. It consists of a microprocessor, a 3-digit display,
a button and some available i/o pins. As it comes from adafruit, it's a counter that displays the number of…... Listed under:
AVR ATmega Projects, Internet - Ethernet - LAN Projects
1848. Getting started with VMUSIC2 The VMUSIC2 is a complete MP3 player module from FTDI, Inc. which makes it easy to
integrate MP3 functionality in to your next microcontroller project. It has two interfaces: SPI or UART (serial) Some example
applications: 1. Make your robot talk and play sound effects…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1849. Jar of Fireflies using AVR ATTiny45 Microcontroller This project uses green surface-mount LED's along with an AVR ATTiny45
microcontroller to simulate the behavior of fireflies in a jar. (note: the firefly behavior in this video has been greatly sped up
in order to be easier to represent in a short film. The…... Listed under: AVR ATmega Projects, Game - Entertainment Projects
1850. I2C Bus for ATtiny and ATmega168 I love the Atmel AVR microcontrollers! Since building the Ghetto Development System
described in this Instructable, I've had no end of fun experimenting with the AVR ATtiny2313 and the ATmega168 in
particular. I even went so far as to write an Instructable on using switches…... Listed under: AVR ATmega Projects,
1851. 16-key Keypad Decoding with an AVR MCU This instructable will show you how to interface a 16-key keypad to your AVR
microcontroller and read the key when a key is pressed. I'll introduce the keypad first, then the 74HC922 16-key decoder IC
as a pin-saving mechanism, then finally how to take the…... Listed under: AVR ATmega Projects, How To - DIY - Projects,

1852. Connecting Nokia 3310 LCD to USB using AVR What do you do with an old phone, a microcontroller and lots of time? You
hook the old phone's LCD screen to the computer USB of course! In this project we're going to communicate with a Nokia
3310 LCD display over USB! How are we…... Listed under: AVR ATmega Projects, LCD Projects, Phone Projects
1853. Repair dead AVR's – Attiny fusebit doctor (HVSP) Did you make a mistake while programming fusebits, or purposely disabled
reset pin (RSTDISBL) or ISP programming (SPIEN)? No need to buy or make inconvenient HV programmer only for unlock
couple of Tiny AVR’s. This Attiny fusebit HV doctor will cure your dead tiny microcontrollers,…... Listed under: AVR ATmega
1854. ATtiny programming with Arduino After this Instructable you should be able to program an A Ttiny85/45 with an arduino. It
may sound complex but it really isn't. After doing some research I could not find to much info on how this could be done. I
however did find http://www.instructables.com/id/Program-an-ATtiny-with-Arduino/. This Instructable…... Listed under: AVR
ATmega Projects, Microcontroller Programmer Projects
1855. ISP 6 pin to 8 Pin Socket Using ATTiny45 The reason i mainly built this project was to program the ATTiny45, which has a 8
pin connection, while my USBtinyISP (from Ladyada) only has a 10 pin and 6 pin connection. After snooping around the
internet for about 3-4 weeks i found nothing what…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects
1856. Micro controller programming: Making a set of traffic lights using Microcontroller ATTiny2313 So you wana learn how to
programme a micro controller? This tutorial has been designed as a next step, following the fantastic tutorial 'Ghetto
Programming: Getting started with AVR microprocessor on the cheap.' by The Real Elliot link you should read this before
progressing onto…... Listed under: AVR ATmega Projects, LED Projects
1857. Instalacion del controlador USBasp (USBasp drivers setup) – Dark Side Electronics using AVR microcontroller English version
available at the bottom Se enseñara paso a paso como instalar los controladores (drivers) necesarios para el correcto
funcionamiento del programador USBasp para microcontroladores AVR. Primero, mencionaremos algunas consideraciones
para evitar fallos por usos indebidos del programador. También se mencionará el protocolo y…... Listed under: AVR ATmega
Projects, How To - DIY - Projects, Microcontroller Programmer Projects
1858. How to Read Binary/Hex Thumbwheel Switch with an AVR Microcontroller using ATmega328p microcontroller This
instructable will show you how to read the number on a binary pushwheel or thumbwheel switch using LED's or an AVR
microcontroller (I'm using an ATmega328p but this can be adapted for any AVR or probably another microcontroller of your
choice). Multiple thumbwheel switches…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1859. AVR LCD Namebadge Using ATtiny2313 So, you're going to a conference/meetup/nerdfest and you want to do something
that sets you apart from normal people. An LCD namebadge powered by an ATtiny2313 is a great way to do that. This is a
general purpose LCD display unit powered by a 9V…... Listed under: AVR ATmega Projects, LCD Projects
1860. Power Your Arduino From Your Car using AVR microcontroller The Arduino -- and AVRs in general -- have a wide range of
power supply options ranging from around 1.8V to 5.5V. The choice of voltage is usually determined by the desired clock
speed or power consumption requirements. The Arduino and its many variants have…... Listed under: AVR ATmega Projects,
Battery Projects, Car Projects
1861. Making a set of traffic lights Using Arduino This tutorial will step you through the process of creating a set of controllable
and configurable traffic lights whilst also teaching you the basics of Arduino. Some knowledge is needed and I highly
recommend reading and following through on most if not all of the…... Listed under: AVR ATmega Projects, LED Projects
1862. LoveBox – The box of love using ATtiny2313 Microcontroller As most guys I don't tell my wife that "I love you" as often as I
should, but this little gadget will at least improve that situation as bit. So by combining a nice box and some hardcore
electronics nerdiness I've made a nice christmas…... Listed under: AVR ATmega Projects, Game - Entertainment Projects
1863. Stripboard Arduino using ATMega168 microcontroller In this, my first Instructable I'm going to show you how to make a
stripped down Arduino for a fraction of the price, using Stripboard/Veroboard. Material List: 1x Atmel ATMega168 = �2.65
1x Stipboard = 72p 1x 7805 Voltage regulator = 26p 2x LEDs =…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1864. Build a Complete AVR System and Play Mastermind Using Microcontrollers The game Mastermind has been around a long time, and I remember
getting a board version with colored pegs when I was a kid. I love this game, as it is solvable simply by pure logic. One player (or a

computer/microcontroller) chooses a sequence of…... Listed under: AVR ATmega Projects, Game - Entertainment Projects
1865. Using Arduino to communicate with embedded project using AVR ATMEGA microcontroller Building a stand-alone AVR
ATMEGA project sometimes leaves you with no easy to read output from your project. But you can use an Arduino to act as a
communications bridge between your embedded project and your PC's Serial Monitor program! I'm building an embedded
multi-channel…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1866. AVR mini board with additional boards using attiny2313 microcontroller Somewhat similar to PIC 12f675 mini protoboard,
but extended and with additional boards. Using attiny2313. Step 1 Scheme Let us first start with a scheme. The scheme is
pretty obvious since it only connects attiny2313 with the pins and the only additional elements are resistors…... Listed under:
AVR ATmega Projects, Development Board - Kits Projects
1867. How to add more Outputs to your Microcontroller using 74HC595 microcontroller This Instructable will show you step-by-
step how to add 8 extra digital outputs, using only 3 of your microcontroller's digital outputs. Step 1 Which Microcontroller
Should You Use? In order to do this Instructable with your microcontroller, you will need to make sure that it has the…...
1868. Guia para programar uC AVR – Dark Side Electronics using AVR microcontroller La forma más sencilla y rápida de programar
un micro-controlador (uC) de la familia AVR, usando el programador USBasp, es utilizado el programa eXtreme Burner - AVR
de Extreme Electronics. En esta guía te detallaremos como programar tu propio uC. Para esto necesitarás lo siguiente:…...
Listed under: AVR ATmega Projects, Microcontroller Programmer Projects
1869. Getting started with ubuntu and the AVR dragon using atmega8 microcontroller Here's what i did to get started using the
AVR Dragon to program ATMEGA8 microcontrollers using ubuntu (This is aimed at beginners, I myself am also being a
beginner, so any improvements from more experienced users are greatly appreciated). After finally switching my laptop
and…... Listed under: AVR ATmega Projects, Microcontroller Programmer Projects, RTOS - OS Projects
1870. Led dimmer 2 channels using Attiny13 microcontroller This is Attiny13 2 channels dimmer with 5 program modes and speed
control: 1. Dim between 2 channels 2. Dim 2 channels together 3. Blink mode 1 4. Blink mode 2 5.Blink mode 3 Step 1
Hardware Dimmer is based ot Attiny13V: - 1k flash…... Listed under: AVR ATmega Projects, LED Projects
1871. Adding ICSP header to your Arduino/AVR board using ISP10PIN microcontroller So you may have been playing with
Arduino's, or rather, Hackduino's. If you made your own Hackduino or similar project, you may be wondering how to add the
ICSP header. Basically, using the ICSP header will allow you to use an external programmer to 'upload'…... Listed under: AVR
ATmega Projects, Microcontroller Programmer Projects
1872. Synchronizing Fireflies using Microcontroller ATtiny13 Have you ever asked yourself how do hundreds and thousands of
fireflies are able to synchronize themselves? How does it work, that they are able to blink all together without having a kind
of boss firefly? This instructable gives a solution and shows how this…... Listed under: AVR ATmega Projects, Development
1873. The Arduino LED Cube using LED microcontroller Are you bored? Do you want to make something amazing to impress your
friends with? Let's try making an LED cube..... A work of art, that lights up..... Step 1 What in the world is and LED? LED is an
acronym for Light Emitting Diode,…... Listed under: AVR ATmega Projects, LED Projects
1874. LED matrix using shift registers This instructable is meant to be a more complete explanation than others available online.
Notably, this will provide more hardware explanation than is available in the LED Marquee instructable by led555. Goals This
instructable presents the concepts involved with shift registers and high side drivers.…... Listed under: AVR ATmega Projects,
LED Projects
1875. Charlieplexing 7 segment displays using Atmel Tiny26 microcontroller Charlieplexing of discrete leds has been the topic of a
few other instructables. The Charlieplexing LEDs- The theory and the How to drive a lot of LEDs from a few microcontroller

pins comes to mind. They are both excellent and should be read by anyone…... Listed under: AVR ATmega Projects, LED Projects
1876. AVR32 Development Board at Home This is my first instructable.So plz comment and help me out with any mistakes i might
commit . I have created a pcb for avr 32 ,its a development board .I saw that there none online with pcb that could be done
at home so…... Listed under: AVR ATmega Projects, Development Board - Kits Projects
1877. Faraday For Fun: An Electronic Batteryless Dice using Microcontroller ATTiny13 There has been a lot of interest in muscle
powered electronic devices, due in large part to the success of Perpetual Torch Perpetual Torch, also known as battery-less
LED torch. The battery-less torch consists of a voltage generator to power the LEDs, an electronic circuit…... Listed under: AVR
1878. DIY Electronic Birthday Blowout Candles Step 1 The Circuit Step 2 Building the Circuit board Step 3 Soldering the Circuit board Step 4 Programming
the Micro Step 5 Using the Candles To power the circuit, you need 4 batteries of 1.2V, AA or AAA size or 3 batteries of 1.5V…... Listed under: AVR
1879. Buggy – A Crafty Programmable LED Creature using Microcontroller Atmel Attiny44v Buggy is a programmable LED craft
project using a homemade, single-sided, PCB board, and a programmable AVR Attiny44v microcontroller. Buggy has two bi-
colored LED eyes and can sense visible and IR light and emit sounds using a piezo speaker. Not counting the board, there
is…... Listed under: AVR ATmega Projects, Microcontroller Programmer Projects
1880. LED Hanukkah Menorah using Microcontroller ATtiny13 I wanted to make an LED menorah for a friend. In planning this I
decided I wanted to keep the parts-count very low and use components I had on hand. I think I have achieved my goals and
couldn't be happier at the outcome of…... Listed under: AVR ATmega Projects, Game - Entertainment Projects
1881. How to choose a MicroController It used to be that the number of different microcontroller chips available to the hobbyist
was pretty limited. You got to use whatever you could manage to buy from the mail-order chip dealer, and that narrowed
down the choice to a small number of chips.…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1882. Swiss AVR Knife using Microcontroller ATtiny84 The Swiss AVR Knife bundles a number of AVR programming projects
together in a single convenient Altoids Gum Tin. Because of the flexibility afforded by microcontroller programming, it also
provides a starting point for any number of projects based on LEDs and sound output. The…... Listed under: AVR ATmega
1883. How To Communicate With An Alien Artifact or . . . Close Encounters of the Curiously Minty Kind. This Instructable will show
you how to build an Altoids version of the 'Close Encounters' mothership, and how to interact with it. This may be vital
training for that day when the Bright White Beam comes to suck…... Listed under: AVR ATmega Projects, LED Projects
1884. LED Microcontrolled Stained Glass Firefly Pendant using Microcontroller ATTiny45 chip This Instructable will walk you through
the steps needed to make a stained glass pendant with anLED that blinks in a pattern using a microcontroller. The blink
pattern is an actual firefly song of a type of Japanese firefly. It is a scaled down version…... Listed under: AVR ATmega Projects,
1885. AVRSH: A Command Interpreter Shell for Arduino/AVR Ever wanted to be "logged in" to your AVR microcontroller? Ever
thought it would be cool to "cat" a register to see its contents? Have you always wanted a way to power up and power down
individual peripheral sub-systems of your AVR or Arduino in…... Listed under: AVR ATmega Projects, RTOS - OS Projects
1886. Build your own (cheap!) multi-function wireless camera controller using Microcontroller AVR ATMega8 Introduction Ever
fancied building your own camera controller? IMPORTANT NOTE: Capacitors for the MAX619 are 470n or 0.47u. The
schematic is correct, but the component list was wrong - updated. This is an entry into the Digital Days competition so if you
find it useful, please rate/vote/comment…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN Projects, Video -
Camera - Imaging Projects

1887. A sunrise and sunset lamp with LEDs You know it, in the winter time it is hard to get up, because it is dark outside and your
body just won’t wake up in the middle of the night. So you can buy an alarm-clock that wakes you up with light. These
devices…... Listed under: AVR ATmega Projects, LED Projects
1888. Ghetto Programming: Getting started with AVR microprocessors on the cheap. Microprocessors are so cheap these days. If
only there were a way to program them up just as cheaply... *wavy dream-sequence lines* In this instructable, find out how to
build up a complete AVR microprocessor toolchain: compiler, programmer software, programmer hardware, and some simple
demos…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1889. Servo Controlled Labyrinth using Microcontroller ATmega32 Do you know this classic wooden labyrinth game with two knobs
for X and Y rotation? So, I've decided to modify one by connecting two standard servos to the knobs and let a
microcontroller (ATmega32) play the game. Credits: - To CarlS www.instructables.com/id/Servo-Controlled-Marble-Maze/ for
inspiration.…... Listed under: AVR ATmega Projects, Motor Projects
1890. LED Scolling Dot Matrix Font & Graphics Generator 5×8 5×7 8×8 If you are into geeking it out with projects of the
electronical kind, then you have likely wanted to create a dot matrix display or a POV. To do this you will need to have a font
file or table to read the characters from.…... Listed under: AVR ATmega Projects, LCD Projects, LED Projects
1891. Color Changing Digital PC Fan Controller using Microcontroller ATMega168 We've all seen LED fans that you can put in your
computer to make it look cool. They usually come in blue, sometimes red or green and consist of a basic PC fan with 4 bright
LED's mounted in the 4 corners. They source their…... Listed under: AVR ATmega Projects, Game - Entertainment Projects, LED
Projects
1892. Atmel Xmega USB/Serial Arbitrary Waveform Generator This instructable walks you through programming and using the
Boston Android Xmega evaluation board to work as a simple arbitrary waveform generator taking advantage of the
integrated 12bit DAC and high speed DMA controller. I have provided precompiled firmware as well as source code which…...
Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1893. LED Cube 4x4x4 using Microcontroller Atmega16 Amazing 3 dimensional LED display. 64 LEDs makes up this 4 by 4 by 4
cube, controlled by an Atmel Atmega16 microcontroller. Each LED can be addressed individually in software, enabling it to
display amazing 3d animations! 8x8x8 LED cube now available, by popular demand:…... Listed under: AVR ATmega Projects,
LED Projects
1894. Infrared Proximity Sensing Coffee Table Module & Color Changing Glowing Faucet using Microcontroller ATMEGA48 This is
merely an instructable to explain how this device operates. I hope everything is not too obfuscated. This prototype consists
of three 8x8” modules. Each module operates independently of each other. Each module consists of 4 “pixels”. Each pixel is 4
inches square and…... Listed under: AVR ATmega Projects, Home Automation Projects
1895. The Multi-format Clock – Gift contest I tend to have good ideas when I don't need them but when I need them I always face
the black wall of no inspiration. I had to come up with an idea for a present for Jeff-O. After a long week without inspiration, I
came…... Listed under: AVR ATmega Projects, Clock Projects
1896. Make a 8×10 L.E.D Matrix using the Arduino and 4017 decade counter In this instructable I will show you how to build a quite
fancy 8 by 10 L.E.D matrix(with scrolling text and animations) using the Arduino and 4017 decade counter. This type of matrix
is easy to make and program and it is a good way…... Listed under: AVR ATmega Projects, LED Projects
1897. LED Binary Calculator using Microcontroller ATtiny2313 You can't calculate binary values "as is" on most handheld calculators
and using the windows one is just a pain, so i decided to make my very own (binary only) calculator. This calculator supports
all the basic functions like : NOT,OR,AND,XOR, addition,subtraction,multiplication,division and modulo. So join me as we…...
Listed under: AVR ATmega Projects, Calculator Projects, LED Projects

1898. Debugging AVR code in Linux with simavr using Microcontroller ATTiny85 I recently started programming AVR chips, namely
the ATTiny85. They can be programmed using C, compilers are readily available in Ubuntu, and you can do a LOT with them -
just search for avr on this site! Anyway, I was having some trouble with my…... Listed under: AVR ATmega Projects, RTOS - OS
Projects
1899. Power your Arduino/AVR with a Hand-Cranked Battery If you've ever wanted to power your Arduino or AVR from a battery
for development testing (batteries have different power delivery qualities than, say, transformed AC or even a regulated wall
wart in DC) testing but were tired of going through batteries (Hey, I admit…... Listed under: AVR ATmega Projects, Battery
Projects
1900. USB controlled home automation hack using Microcontroller ATmega8 Hack a wireless home automation system to be USB
controlled using two AVR microcontrollers! Check out the video! The system is really more responsive, but the browser on my
phone is slow. Skills ans tools There are two ways of hacking an RF remote to…... Listed under: AVR ATmega Projects, Home
Automation Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1901. Music Playing Alarm Clock using Microcontroller AT90USB1286 This Instructable will be about designing a music player from
using various building blocks. You will understand the communication between the microcontroller, memory, computer, LCD
display, RTC, IR remote, and the music file decoder. I will try my best to to teach you in a…... Listed under: AVR ATmega
Projects, Clock Projects, Game - Entertainment Projects, Sound - Audio Projects
1902. Rechargeable Battery Capacity Tester using Microcontroller ATMega168 Do you have a pile of AA rechargeable batteries in
your drawer? Some are old, some are new, but which sets would you bring with your camera on your next trip, and which
ones are past their useful life? I like using rechargeable batteries, but…... Listed under: AVR ATmega Projects, Metering -
Instrument Projects
1903. Mechanized Android Figure using Microcontroller ATtiny44A These Android figures are cute, but they don't actually do
anything. Let's change that. Have a look at the video: These are the steps to make an Android that reacts to sound, moves it's
head, sends out Morse Code messages and displays some cool light…... Listed under: Android Projects, AVR ATmega Projects,
1904. Numitron clock & thermometer using Microcontroller atmega48 I really like nixie and numitron clocks, but I never worked
with them before. So I decided to give it a go. I choose numitrons because of 2 reasons: first of all nixies need a higher
voltage than numitrons to work. Nixies need around 170V…... Listed under: AVR ATmega Projects, Temperature Measurement
Projects
1905. Yet Another Daft Punk Coffee Table (5×5 LED Matrix) Yes, I know this has been done before, but I wanted to build my own,
using as few parts as possible. I built this as a table top or wall mount model, but it can be scaled up to make a coffee table.
I built…... Listed under: AVR ATmega Projects, Home Automation Projects
1906. Build your own Wifi radio using Microcontroller ATmega16 The internet hosts lots and lots of online radiostreams, most of
them with a certain theme, ranging from old time classics to Tibetian riverdancing. I must admit that I love to listen to them
while I'm building stuff, as I can choose the music I…... Listed under: AVR ATmega Projects, Internet - Ethernet - LAN Projects,
Radio Projects
1907. How to get started with Eclipse and AVR Programming AVRs is fun, but sometimes the manufacturers development
environments make code maintenance a chore. If your looking for a free, cross platform, high quality piece of software for
programming AVRs Eclipseis a good choice.Moving to an Integrated Development Environment (IDE), such as Eclipse is…...
1908. Lampduino – an 8×8 RGB Floor Lamp Lampduino is a computer-controlled free-standing floor lamp, comprised of an 8x8
RGB LED matrix. The lamp stands 45" high and 18" wide. Light emanates from both sides. It has various display modes, as
well as an included editor for creating animations. The lamp is controlled…... Listed under: AVR ATmega Projects, LED Projects

1909. Rainbow glowing ping pong Using ATTing 13 While I was finalizing e-snowflake project, I imagined that single RGB 5050 LED
would create nice rainbow effect if placed inside a ball like ping-pong. You can find plenty of such projects on the net, this
one was heading to embed everything within ping-pong, battery…... Listed under: AVR ATmega Projects, Game -
1910. Charlieplexing 7 segment displays using Microcontroller This instructable describes how to charlieplex a bunch of 7-segment
led displays. Charlieplexing of discrete leds has been the topic of a few other instructables. The Charlieplexing LEDs- The
theory and the How to drive a lot of LEDs from a few microcontroller pins comes…... Listed under: AVR ATmega Projects, LED
Projects
1911. How To Use a Nokia Color LCD using an AVR Nokia manufactures a wide variety of cell phones and many of their cheaper
phones contain simple LCD's which may be used in microcontroller projects. There is one particular LCD model that is used
in a wide variety of their phones and is often referred to…... Listed under: AVR ATmega Projects, LCD Projects
1912. How to Read Many Switches with One MCU Pin Have you ever been chugging away at a project(s) and the project keeps
growing and growing, while you add more things to it (we call that a Feaping Creaturism)? On a recent project, I was building
a frequency meter and added a five function signal…... Listed under: AVR ATmega Projects, Other Projects
1913. Cellphone Operated Robot Using Microcontrollers Component Required: IC1 - MT8870 DTMF decoder IC2 - ATmega16 AVR
microcontroller IC3 - L293D motor driver IC4 - 74LS04 NOT gate D1 - 1N4007 rectifier diode R1, R2 - 100-kilo-ohm R3 - 330-
kilo-ohm R4-R8 - 10-kilo-ohm C1 - 0.47μF ceramic disk C2, C3, C5,…... Listed under: AVR ATmega Projects, Phone Projects,
1914. An Absolute Beginner's Guide to 8-Bit AVR Programming-AVR Dragon If you'd like to test the waters of microcontroller
programming, the new AVR Dragon by Atmel Corporation is a nifty, low-cost entry-level development tool. Unfortunately,
right out of the box, the AVR Dragon is not the definitive answer for the beginner looking for an all-in-one…... Listed under:
AVR ATmega Projects, How To - DIY - Projects
1915. ATTiny2313 Multi-mode LED Matrix Clock This is a mutli-mode clock project based on attiny2313. it employs a 8x8 led matrix
as display. with the limited resolution, this 12 hour clock shows time in 6 different modes. The circuit employs row and
column multiplexing to drive the leds, one row at…... Listed under: AVR ATmega Projects, Clock Projects, LED Projects
1916. Temperature Indicator Using attiny2313 micrcontroller Description Features: Measures temperatures from -55°C to +125°C
Three LED's to indicate in what range the temparature is. User definable thermostat with high and low settings Output via a
relay to control a heater element or a blower fan (or something else) Power supply ......................4.5…... Listed under: AVR
ATmega Projects, Temperature Measurement Projects
1917. Stepper motor Driver Using AT2313 microcontroller Description With this circuit you can drive a unipolar stepper motor. It
operates in full step mode. You can get a stepper motor from an old 5.25 disk drive. The AVR attiny2313 micro controller
controls the pulses for the stepper motor. The pulses are amplified…... Listed under: AVR ATmega Projects, Motor Projects
1918. Relais Board Using AT2313 Description This is a peripheral board with 4 relais, rated at 5A/250V each. The board has a ML10
output connector for connection with the AT2313 Project board. It has also 4 LED's for indication which relais is switched on.
Hardware The circuit is simple, it…... Listed under: AVR ATmega Projects, How To - DIY - Projects, Interfacing(USB - RS232 - I2c
-ISP) Projects
1919. DS1820 Temperature Controller using atmega8515 microcontroller This project displays the temperature on an LCD display
with an resolution of 0.06degrees. DS1820 is used for sensing the temperature. It can measure temperature range from
-55deg to +125deg. But i take care of only the possitive temperature. There are 3 switches to change…... Listed under: AVR
1920. Real Time Clock PCF8583 Using AVR microcontroller Description The PCF8583 is a clock/calendar circuit based on a 2048-bit
static CMOS RAM organized as 256 words by 8 bits. Addresses and data are transferred serially via the two-line bidirectional
I2C-bus. The built-in word address register is incremented automatically after each written or read…... Listed under: AVR
ATmega Projects, Clock Projects
1921. 8×8 Dotmatrix Scrolling LED display using atmega8515 microcontroller Here's an another project, which makes an Scrolling LED display. Here 64 leds
which are connected to an Matrix display. The Anodes are drived through an Driver IC UDN2981 and the cathodes are drived through ULN2803. The

Atmega8515 is used in this project to control…... Listed under: AVR ATmega Projects, LED Projects
1922. Bluetooth Based Smart Home using atmega8 microcontroller This project is used to automate the home appliances through
Bluetooth enabled PC. You can use the USB Bluetooth at the PC side and an Serail Bluetooth converter is used at the
microcontroller side. The sparkfun bluetooth module is used here, but you can use…... Listed under: AVR ATmega Projects,
1923. Multipattern Running light using ATtiny2313 microcontroller Here's an another project with LED. It can show different
patterns. There are 11 channels of LED. Circuit Diagram For more Detail: Multipattern Running light using ATtiny2313
microcontroller... Listed under: AVR ATmega Projects, LED Projects
1924. Real Time Clock ATMega16 Description The ATMega16 chip in the M16 has a real-time counter that operates asynchronously
when a 32,768hz watch crystal is connected to it, providing a real-time clock. Bascom has built-in support for the RTC, making
it very easy to use time functions. The watch crystal…... Listed under: AVR ATmega Projects, Clock Projects
1925. PC Thermometer Using ATTiny2313 Description With this project you can show the temperature on you PC. This
thermometer plugs in on any free serial port. It gives temperature readings accurate to 0.5°C with no calibration.The project
consists of the ATTiny2313 RS232 Project board and the DS1621 Thermometer board and…... Listed under: AVR ATmega
1926. PC Steppermotor Driver Using AT2313 µ-controller Description With this circuit you can control two unipolair stepper motors
in full step mode via the RS232 serial port of your PC. A terminal program such as Hyperterminal can be used to control the
stepper motors. The stepper motors can be driven one at…... Listed under: AVR ATmega Projects, Motor Projects
1927. LCD Thermometer TCN77 Using AVR Microcontroller Description The TC77 is a digital temperature sensor with a Serial
Peripheral Interface. Temperature data is converted from the internal thermal sensing element and made available at anytime
as a 13-bit two’s compliment digital word. Communication with the TC77 is accomplished via a SPI and…... Listed under: AVR
1928. LCD Thermometer TCN75 Using ATTiny2313 Description This small thermometer board uses the Microchip TCN75 device. It is
a cheaper clone of the LM75, it costs about 2,50 Euro. The TCN75 comes in a SO8 packaging. The TCN75 is a serially
programmable temperature sensor. It has an output that is programmable…... Listed under: AVR ATmega Projects,
1929. LCD Thermometer LM35 Using AT Mega8 Description The LM35 of National Semiconductors that is used in this project is a
precision centigrade temperature sensor, which has an analog output voltage. It has a range of -55ºC to +150ºC and a
accuracy of ±0.5ºC . The output voltage is 10mV/ºC . The…... Listed under: AVR ATmega Projects, Temperature Measurement
Projects
1930. AVR GPS Locator using avr microcontroller In this project i have interfaced an GPS with AVR microcontroller, the ATtiny2313
gets the location from the GPS and display it over the LCD display. This project also have the feature of marking a place with
its name. For entering the Name of the…... Listed under: AVR ATmega Projects, GPS Based Projects
1931. MMC card based WAV player using atmega32 This projects gives you a simple wav player with help of the MMC card
connected to ATmega32. You can use any AVR microcontroller. The MMC card works on 3.3v so a 3.3v regulator is used and
the 5v to 3.3v level conversion is done by…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1932. LCD Message Display Using AT Mega8 microcontroller Description This LCD message display can show text with large
characters on an 20*4 LCD module. The display can show five characters at a time. Each characters is build from twelve
characters of the display module. The text on the display can be read from…... Listed under: AVR ATmega Projects, LCD
Projects
1933. LCD Interface Board Using ATTiny2313 Description This board can directly connected to the STK 500 board or the ATTiny2313 ISP program board with
a 10 pole flatcable on the 10 pin header of the STK500 and the 10 pin header of the LCD/Switch board. The display has 16*2 character positions…...
Listed under: AVR ATmega Projects, LCD Projects

1934. 8 MHz frequency meter using AVR microcontroller This project can measure the clock pulses fed to the Timer input of the
AVR microcontroller. The Bascom code counts the clock pulses for 1 second and display it over the LCD display. The
frequency is displayed in Hertz and this project can measure a…... Listed under: AVR ATmega Projects, Metering - Instrument
Projects
1935. LCD Display On Glass Interface Using AT2313 Description Liquid Crystal Display on Glass is the newest in LCD technology. The
display's are very compact, it measures 55x27 mm and the height is only 2mm without LED backlight and 5.8mm with LED
backlight. The display's can have different LED background light instead of…... Listed under: AVR ATmega Projects, LCD
Projects
1936. Temperature controlled fan using PWM microcontroller This project gives you a simple temperature controlled fan. If the
difference between real temperature and the user temperature is high then the fan will run at full speed and if the difference
is low then the fan will rotate at slow speed. The speed…... Listed under: AVR ATmega Projects, PWM Projects, Temperature
1937. SMT160 based Temperature indicator There are lot of temperature sensors both with analog & digital outputs. This project
gives you an another temperature indicator which has been done with a digital sensor SMT160. Although it is a digital sensor
it does not gives out the temperature directly. The output…... Listed under: AVR ATmega Projects, Temperature Measurement
Projects
1938. Digital Melody player using atmega16 microcontroller Here' s an melody player with Atmega16. The command "Sound
Speaker" is used to generate sound. This is the inbuilt command in Bascom AVR. For more Detail: Digital Melody player using
atmega16 microcontroller... Listed under: AVR ATmega Projects, Sound - Audio Projects
1939. Stepper motor Control with Atmega16 With this project you can control a unipolar stepper motor. You can control both the
speed and the direction of the motor. The speed and direction and can changed with help of the keypad. The data's are
displayed over the LCD display. A 4x4 keypad…... Listed under: AVR ATmega Projects, Motor Projects
1940. Graphical LCD with KS108 controller Description The Graphical LCD 128x64 controlled is with the ATMega16, the graphic LCD
GLCD HG1286418C-VA with a S6B0107/S6B0108 controller is used. See below for the pinout of the display. The display has 8
data bits and 5 control bits. The databits are hooked to PORTB…... Listed under: AVR ATmega Projects, LCD Projects
1941. Simple calculator using avr microcontroller Atmega16 Here's a simple calculator with the Atmega16 microcontroller. It have
an LCD display and a 4x4 keypad. You can also download the proteus simulation file on the downloads Bascom Code
$regfile = "m16def.dat" $crystal = 1000000 Config Kbd = Portd , Debounce = 30…... Listed under: AVR ATmega Projects,
Calculator Projects
1942. Transform a cheap RC Transmitter with Custom Firmware using ATMEGA64 Microcontroller The Turnigy 9x is a cheap Chinese
radio transmitter widely sold by hobby king and other retailers under a variety of names. This is a computerized radio
transmitter and is already a great deal for the price ($53 currently) and pretty capable if you can…... Listed under: AVR ATmega
Projects, Radio Projects
1943. ATTiny2313 Board RS232 Description This board is a small controller board on which you can build your projects. It is suited
for educational use, experiments or prototyping. The board uses the AT2313 microcontroller with a 10Mhz crystal. The board
contains the ISP 10-pin connector for in circuit serial…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -
ISP) Projects
1944. Make an automatic plant light using ATTiny26 Microcontroller This light helps your plants grow. I got the idea from the
Garduino, but nothing is taken from it. The schematic and the program are mine. This plant light gives your plants 4
additional hours of light per day. When it gets dark, it turns…... Listed under: AVR ATmega Projects, Game - Entertainment
Projects
1945. LED wind indicator Using atmega8 Microcontroller I have something with the weather. I always like to know how warm or cold it is, how much rain has
fallen, how hard the wind blows and from what direction,... and so there are lots of sensors around our house to keep me up…... Listed under: AVR
ATmega Projects, LED Projects

1946. Ghetto Pixels – Building an open source BlinkM Using ATTiny45 Microcontroller Unless you've been living under a digital rock
for the last few years, or just simply aren't interested in flashing lights, you'll already know about the awesomeness that is the
BlinkM from ThingM. It's a very small PCB featuring a high power LED that responds very easily…... Listed under: AVR ATmega
1947. USB PCB Business Card Using ATtiny85 Microcontroller This is a business card that will type out some text when you plug it
into a USB port. It uses a ATtiny85 microcontroller with V-USB based code to emulate a keyboard. The typing is triggered by
the CAPS LOCK status LEDs being toggled 3…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP)
1948. Using ATMega328 Microcontroller Custom Tron Disc Mod In this Instructable, I cover modding the store-bought Deluxe
Identity Disc to an upgraded version with 64 leds, controlled by an AVR MCU. The upgraded version is costume-ready and
would be an excellent addition to your Tron costume - it'll also look great on your…... Listed under: AVR ATmega Projects, LED
Projects
1949. DIY TiX Clock using ATMEGA16 AVR microcontroller Here's my instructable for a DIY TiX clock. It is powered by an AVR
microcontroller. The display is made up using a piece of reflector grid you find covering office lights, some smoked perspex,
a diffuser and a bunch of LED's. The Idea came from…... Listed under: AVR ATmega Projects, Clock Projects
1950. Starry Ceiling for Kids Bedroom Using AT90S8538 microcontroller When my little girl was born I wanted to make her a special
night light for in her room. I made her a ceiling light with twinkling stars. It is made up of a piece of custom wood with 100
LEDs mounted in it. An…... Listed under: AVR ATmega Projects, Game - Entertainment Projects, Home Automation Projects
1951. Using max7219 microcontroller Build an electronic score keeper/storage box The instruction manual for each of the MANY
munchkin series of card games always includes a phrase like "you will need a 10 sided die for each player or some other
device to keep score." 10 sided dice are not hard to find in my…... Listed under: AVR ATmega Projects, Other Projects
1952. Using AtTiny2313 microcontroller Build an electronic polyhedral die Dice are fun. Polyhedral dice used in D & D are even
more fun, particularly in big handfuls of different sizes. But a handful isn't always practical. Ever since I saw the dragon bone
electronic die wand advertised in the back pages of Dragon magazine…... Listed under: AVR ATmega Projects, Other Projects
1953. Turn a TV-B-Gone into a super camera remote Intro: My Nikon DSLR has an infrared remote function (remote sold
separately) that is really handy, but fairly limited in range. A while ago, I bought a TV-B-Gone Kit from it's inventor Mitch
Altman, and it can turn TV's off from a great distance. I…... Listed under: AVR ATmega Projects, Video - Camera - Imaging
Projects
1954. How to drive a lot of LEDs from a few microcontroller pins. Using the fact that many microcontroller pins have three states
(+V, GND, or "high impedence"). You can drive N*(N-1) LEDs from N pins. So the little 8 pin microcontroller like a PIC12Fxxx
or an ATtiny11 can drive 20 LEDs on its five available output pins,…... Listed under: AVR ATmega Projects, LED Projects
1955. Hack a Toaster Oven for Reflow Soldering using ATmega32 microcontroller As I get more serious into my electronics hobby, I
need to work with more SMD components. Some component packages are very difficult or impossible to solder with a
traditional soldering iron. To solve this problem, I decided to hack a toaster oven to become…... Listed under: AVR ATmega
Projects, CNC - Printing Machines Projects
1956. Using the 8Pin ATTINY programming shield with an external clock Instructables author extraordinaire Randofo created a great programming shield to
use your Arduino to program 8 pin ATTINY processors. He was even generous enough to give 50 copies of it out to people who authored
instructables using AVR processors. It works great on brand new ATTINYs and…... Listed under: AVR ATmega Projects, Other Projects

1957. Picopter using Microcontroller ATmega128RFA1 Update May 4 2012: I am still working very hard on version 3 of Picopter. The
new version's hardware is already done. There are new 3D printed motor holders. I've done some measurements with regards
to mass and radio spectrum. I've posted stuff to http://www.frank-zhao.com/picopter_forum/index.php including…... Listed
under: AVR ATmega Projects, Robotics - Automation Projects
1958. Box with a Music Lock using ATMega328P Microcontroller There are a lot of locks out there. There are locks open with a key,
with a combination of digits, with various bodily parts, or with a correct geolocation. I decided to make a lock that I have not
seen yet. Since I am learning…... Listed under: AVR ATmega Projects, Game - Entertainment Projects
1959. Measure negative temperature with Lm35 LM35 can measure temperatures from -55deg to 150deg and we need negative
supply voltage for measuring this negative temperature. This circuit eliminates the negative voltage power supply and this
project can measure the negative temperature Download the protesu file to simulate the project on your…... Listed under:
AVR ATmega Projects, Metering - Instrument Projects, Temperature Measurement Projects
1960. DC Motor Speed Control using PWM This project gives a speed control of DC motor through PWM method. The Dc motor is
derived by the L298 driver IC. You can also control the direction of the motor. There are three buttons to control the motor.
Also a bar graph Led display…... Listed under: AVR ATmega Projects, Motor Projects
1961. ISD4004 based voice recorder So far we have seen various devices that are talking, such us cars, dolls etc.This project is also
like one of them. you can use it in various projects such us IVS, robots etc. There are various voice recording IC's. They have
different recording time…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1962. Thermometer with Clock using ATmega16 This project will display the temperature and time over the LCD display. LM35 is
used to sense the temperature and the analog out of the LM35 is converted to digital by using the inbuilt ADC on the
ATmega16 chip. An software clock is generated and…... Listed under: AVR ATmega Projects, Temperature Measurement
Projects
1963. Scientific Calculator using AVR Microcontroller This project gives you a nice and simple scientific calculator using AVR
microcontroller. It has 2 keypads as shown in the circuit diagram and the results are shown on the 16x2 LCD display. You can
do sin,cos, tan functions using this project. The code is…... Listed under: AVR ATmega Projects, Calculator Projects
1964. Traffic light controller using avr microcontroller Here's a traffic light controller using avr microcontroller. It can be adopted for
a four way road. The code is written in Codevision C. You can download the C code and the proteus file from the download.
For more Detail: Traffic light controller using avr…... Listed under: AVR ATmega Projects, LED Projects
1965. ATTiny Board For AVR ATTiny microcontrollers Description With this small board you can program most of the AVR ATTiny
microcontrollers or you can build your projects to use it in a stand alone application. It can be powered with a 9V battery
because it has 5V voltage regulator on it. The…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1966. DS1307 based Clock using lcd This project gives you a real time clock with the RTC chip DS1307. This RTC chip has inbuilt
oscillator for clock and it has its own registers for full calender. In this project we dont take care about the days and we just
use the…... Listed under: AVR ATmega Projects, Clock Projects
1967. Digital dimmer using Microcontroller atmega8 This project is used to control the brightness of the lamp or can be used to
control the speed of the fan. The system consists of 3 block they are Zero crossing detector Microcontroller (Atmega8) Load

Driver (BT136)As the name implies the zero crossing detector…... Listed under: AVR ATmega Projects, Home Automation Projects
1968. Digital Voltmeter using Microcontroller Atmega8 This project gives you a digital voltmeter which can measure voltage from
0v to 25V DC. The values are displayed over the 7segment display. Atmega8 is used and the internal ADC is used to measure
the DC voltage. The resistor network is used to reduce…... Listed under: AVR ATmega Projects, Metering - Instrument Projects
1969. Make-Yourself ATmega32 Starter's Kit with LCD, I2C, SPI, RTC, ADC interfaces Here is my home-made kit of ATmega32
microcontroller interfacing. The ATmega32 controller is rich with features like onboard 32kB in-System programmable flash, 1
KB EEPROM, 2KB SRAM, 10bit ADC (8 channel), SPI bus inteface, TWI (compatible with I2C bus) interface, an USART, analog
comparator, etc.…... Listed under: AVR ATmega Projects, Development Board - Kits Projects, Interfacing(USB - RS232 - I2c -ISP)
Projects
1970. Capacitance and Inductance meter using Atmega8 This project can measure capacitance and inductance using the Atmega8
microcontroller and the code is written in Bascom AVR. The limitations of this project is Inductance Range: 0.1?H to 2H
Capacitance Range: 1pF to 2.5?F Electrolytic Capacitor Measurement Range: 0.1?F to 30000?F Circuit Diagram: For…... Listed
1971. SD/SDHC Card Interfacing with ATmega8 /32 (FAT32 implementation) Here is my project on interfacing of SD Card (microSD).
microSD cards are available very cheap nowadays, a great option for having a huge memory in any embedded system
project. It is compatible with SPI bus, so the interfacing is easy. SD card adapters are…... Listed under: AVR ATmega Projects,
Interfacing(USB - RS232 - I2c -ISP) Projects, Memory - Storage Projects
1972. LPH7319 controlled via I2C I recently obtained a very old mobile phone from a friend. The battery was dead, so I dismantled
it and to my surprise found a display with soldered contacts. In other mobile phones the display was connected via a
conducting polymerpad, which was extremly difficult…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -
ISP) Projects
1973. microSD FAT32 testing using Visual C++ This post presents a way for testing and learning the FAT32 system on microSD/
SDHC cards without building the hardware with microcontroller, thanks to Henry Yiu. This project uses the FAT32 library
available in my previous post, but does away with the microcontroller part. So,…... Listed under: AVR ATmega Projects,
Memory - Storage Projects
1974. Ultrasonic range finder using ATMega8515 This project is used to measure the distance using ultrasonic sensors. The
ultrasonic signal passes through the atmosphere to a barrier, which we want to measure the distance. Part of this signal is
reflected and travels back to the receiver. The time delay between sending…... Listed under: AVR ATmega Projects, Other
1975. 4×4 LED Display The 4×4 LED Display was my first project with a two-layer circuitboard layout. The alignment was not 100%
optimal, but sufficent. I wanted to make the board as small as possible, so the parts had to be stacked at some places. The
square LED’s were…... Listed under: AVR ATmega Projects, How To - DIY - Projects, LED Projects
1976. microSD ATmega32 Data-Logger Aim of this project is to present a way to store a large quantity of data into microSD card in
files with FAT32 format. Here, ATmega32 is used for data collection and microSD interface. The data is received from in-build
8-channel ADC of ATmega32. One…... Listed under: AVR ATmega Projects, Memory - Storage Projects
1977. UV Exposure Unit & Etching Manufacturing circuitboards containing SMD-parts with toner-transfer is nearly impossible. The
thin traces almost never get transferred completely to the copper. One solution to this problem is to use photoresist boards
and expose them with UV light. The layout is printed onto a transparency, which is…... Listed under: AVR ATmega Projects,
Other Projects
1978. 8×8 Bicolor LED Matrix using MAX6964 For a long time I had a layout for this circuit, but could never build it, because the
layout was to small to be made by tonertransfer. So it was the first layout I made with my new exposure unit. It’s quite small,
so it…... Listed under: AVR ATmega Projects, LED Projects

1979. Thermometer using DS1621 and Nokia 3310 LCD interfaced with ATmega8 I am presenting one application with the Nokia
3310 LCD: Designing a thermometer using DS1621 temperature sensor IC. DS1621 is 8-pin sensor from Maxim, with temp
range of -55 to +125 degree C, which can be interfaced with microcontroller over two-wire serial i2c bus. It…... Listed under:
AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects, Temperature Measurement Projects
1980. EPROM Display using ULN2308A microcontroller Due to university and work it has been a while since the last post. But I just
completed a little project that’s worth posting. Several old 27C256 EPROMS were lying around unused. So I thought about a
purpose for them. As I also had some…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232 - I2c -ISP) Projects
1981. CNC Update 2 Using atmega32 microcontroller Another update on the CNC. The interfaceboards are etched, soldered and
tested. IO / Control Boards Step- and directionsignals are generated by an ATmega32 which is controlled over RS232. This is
only for testing purpose. In the final version a PC will control the movement.…... Listed under: AVR ATmega Projects, CNC -
1982. Delta Robot using atmega32 micrcontroller And now for something completely different: A little robotics project for the
weekend. The described robot can be build entirely from model making supplies and materials from the hardware store. Also
only very few tools are needed. A metal saw, a drill press, a vice…... Listed under: AVR ATmega Projects, Robotics - Automation
Projects
1983. Simple PWM DC motor control using MOSFET H-Bridge with AVR ATmega8 Here is a very simple project of controlling a
small DC-motor (taken from an old personal cassette player) with ATmega8. The ATmega8 is having three PWM channels, out
of which two are used here. PWM waveforms are fed to MOSFET (RFD3055) H-bridge. Here, direction is…... Listed under: AVR
ATmega Projects, PWM Projects
1984. circuit schematic symbols circuit schematic symbols: Download High Quality circuit schematic symbols images of common
electrical and electronics components, for creating any schematic diagram. Basically Electrical components can be divided in
two categories Passive components and Active Components. This post will have following schematic symbols. Click on
Image…... Listed under: Blog, Circuits
1985. 4 bit interfacing of a 16X2 LCD display to PIC16F877A, Atmega16/32 & MSP430 16x2 LCDs are most commonly used display
units in microcontroller based projects. I got much information about LCD, LCD commands, LCD initialization etc from the
below link and I hope, it will be very much helpful for beginners. For more Detail: 4 bit interfacing of…... Listed under: AVR
ATmega Projects, LCD Projects
1986. My own AVR ISP programmer using PIC16f877a and python! Introduction: (don't skip to read the note below) I recently
purchased few AVR microcontrollers. I don't know much about AVR since I am using it for first time. Any way, I have some
experience on working with PIC and MSP430. To program AVR using USB,…... Listed under: AVR ATmega Projects,
1987. 4×4 Matrix Key-board Interfacing with ATmega32 Here is a project for beginners to interface a 16-key (4x4) keypad with
ATmega32 using 8-pins i.e. one port of the microcontroller. This is useful particularly where we need more keys but don't
want to spend more uC pins for interfacing. The 4x4 keypad is…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232
- I2c -ISP) Projects
1988. NOKIA 3310 LCD interfacing with ATmega8 Using graphic LCD in a project gives it really a good look and flexibility of
displaying different characters and shapes. But, the graphic LCDs are quite costly. The NOKIA 3310 LCD provides a really low-
cost solution to add a small graphic display into your project…... Listed under: AVR ATmega Projects, Interfacing(USB - RS232
- I2c -ISP) Projects, LCD Projects
1989. DIY AVR Programmers For those who are trying to make AVR kit at home, an AVR programmer which can be simple to make
will be really useful, as it'll avoid buying the programmer!! Here I'm giving a few webpage links on how to make a
programmers yourself. -…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1990. TV remote controller 160KHz High Quality Stereo MMC WAV player using ATMEGA32 Introduction: This is my first AVR based hobby project and the
most successful one compared to my all previous stuff. I am 100% satisfied with this work. Few months ago, I tried to make a wav player using a

PIC16F877A. It worked anyway, but the…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1991. Multitasking in AVR (A demo to run 7 tasks on an atmega32) Introduction: Switching multiple tasks on a same CPU is the one
of the major function of an operating system. What I did now is a time sharing multitasking (time multiplexing) on an AVR.
Here an atmega32 is configured to use Round-Robin Multitasking. Round-Robin allows quasi-parallel…... Listed under: AVR
ATmega Projects, RTOS - OS Projects
1992. An attempt to show grayscale images on an LED dot matrix display with software PWM using PIC16F877A Introduction: This
is just a time pass hobby project, I am trying to display some pictures (JPEG/PNG/BMP etc) on my 8x8 led dotmatrix display.
You can see photos of my 8x8 led dotmatrix display showing some grayscale pictures. The main thing which you may
notice…... Listed under: AVR ATmega Projects, PWM Projects, Video - Camera - Imaging Projects
1993. AVR based monochrome signal generation for a PAL TV using atmega16 micrcontroller Introduction: I have learned some
thing about TV in one of my B.tech semester but I forgot most of them. Now I refreshed a few basics and tried to implement
a monochrome PAL TV signal generator using an AVR micrcontroller. I was using PIC earlier…... Listed under: AVR ATmega
Projects, Video - Camera - Imaging Projects
1994. Drawing geometric figures on a PAL TV using ATmega32 (128×64 resolution) Introduction: I am interested to draw lines,
square, rectangle, circle etc on my TV screen. At first I was confused where to start. While thinking about it, a pencil and an
eraser came to my mind. If we have a good pencil, eraser and a…... Listed under: AVR ATmega Projects, Video - Camera -
Imaging Projects
1995. Running PYTHON (pymite-09) on an Arduino MEGA 2560 using atmega16 micrcontroller Now it is the first time I am using an
arduino board. Arduino mega 2560 is really a great product. The chip got a flash of 256KB, RAM of 8KB and EEPROM of 4KB.
Also, the data sheet of Atmega2560 says that we can extend…... Listed under: AVR ATmega Projects, How To - DIY - Projects
1996. Generating AUDIO ECHO using Atmega32 microcontroller Introduction: But now I can do this very easily by a simple digital
signal processing using a microcontroller. It's concept is very simple, ie we need to apply a proper delayed feedback in digital
samples with in a circular buffer. I did this using an…... Listed under: AVR ATmega Projects, Sound - Audio Projects
1997. Implementing Discrete Fourier Transform in Atmega32 to make an audio spectrum analyzer "All waveforms, no matter what
you scribble or observe in the universe, are actually just the sum of simple sinusoids of different frequencies." Hi, I am just
refreshing the basics of fourier transform. I am not an expert. Now I did a small audio spectrum…... Listed under: AVR ATmega
1998. Arduino Mega 2560 What is Arduino Mega 2560: The arduino mega 2560 is a microcontroller board in line with the
ATmega2560 (ATmega2560 datasheet). It's having 54 digital input/output hooks (of which 14 can be used PWM results), 16
analogue inputs, 4 UARTs (Universal asynchronous receiver/transmitter) to interface with…... Listed under: AVR ATmega
Projects, Blog, Circuits, How To - DIY - Projects
1999. Homage UPS Schematic Circuit Diagram Homage UPS: Homage UPS is one of the top selling brand. Homage UPS/Inverter is
based on chopper technology having modified sine wave. It has overload output protection, with batter and output volts
measurements displayed on LCD interface. Further specifications are mentioned in undergiven table Homage…... Listed
under: Blog, Circuits
2000. PCM UPS Schematic Diagrams PCM Powercom was founded in 1987, a leading provider of power protection products with
ISO 9001 certificate. There are over 2,600 employees around the world. Powercom designs, manufactures, markets and
services UPS systems. PCM UPS Schematic Diagram for Model ULTIMATE 700/1000/1500VA POWER Features : LED/LCD…...
Listed under: Blog, Circuits
2001. PowerMan UPS Schematic PowerMan UPS/Inverters Uninterruptible power supplies and voltage regulators Business founded
in 1993. Prior to 2000. company engaged in distribution of products of famous brands. In the year 2000. the idea of

creating
his own brand POWERMAN, and from that period, the company is exclusively OEM…... Listed under: Blog, Circuits
2002. APC UPS Schematic Diagrams APC by Schneider Electric, formerly referred to as American Energy Conversion Corporation, is
really a manufacturer of uninterruptible energy supplies, electronics peripheral devices and data center items. In 2007,
Schneider Electric acquired APC and combined it with MGE UPS Systems to create Schneider Electric's Critical…... Listed
under: Blog, Circuits
2003. UPS Schematic Circuit Diagram UPS is an abbreviation of Uninterpretable Power Supply. It is an electronic product used to provide backup power for
sensitive devices in case their normal power failure or blackout. Given UPS Schematic Circuit Diagram with its component list is a complete guide to
build standard…... Listed under: Blog, Circuits, Featured

Explore All Categories
let’s socialize
ATMega AVR Weekly Newsletter
Subscribe To A Specific Category
Get Notified Whenever There Is A New Project In Your Desired Category
Subscribe!
Recent Posts
POWERFLEX + 750W DC
LABORATORY POWER SUPPLY
LAUNCHED
5G CELLULAR MODEM M.2
ADAPTER FOR MINI-PCIE SLOTS
ON SBCS
A TINY SENSOR IN GE
DEVELOPMENT COULD ENABLE
SMARTPHONES TO DETECT
COVID-19 CORONAVIRUS
Useful Resources
Download Offline Projects in PDF
Complete Projects List
AVR Atmega16 based Projects List
Atmega328 avr based projects list
Proteus simulation based avr
projects
ATTiny85 ATTiny45 and ATTiny13
based projects list
Online Courses to Learn
ATMega32 AVR Programming
Advance Search
Enter Keyword:
Search
Social icons
2016 Powered By Wise Technologies, Atmel-avr Theme By Wise Technologies Privacy Policy
Terms of Service
Copyright Policy
About Us
Sitemap

Advanced View of Atmega Microcontroller Projects List - Projects Tutorials Code Library for Atmels Atmega32 AVR.pdf

Recommended

More Related Content

Similar to Advanced View of Atmega Microcontroller Projects List - Projects Tutorials Code Library for Atmels Atmega32 AVR.pdf (20)

More from WiseNaeem (20)

Recently uploaded (20)

Advanced View of Atmega Microcontroller Projects List - Projects Tutorials Code Library for Atmels Atmega32 AVR.pdf