C011141018

IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE)
e-ISSN: 2278-1676,p-ISSN: 2320-3331, Volume 11, Issue 1 Ver. IV (Jan. – Feb. 2016), PP 10-18
www.iosrjournals.org
DOI: 10.9790/1676-11141018 www.iosrjournals.org 10 | Page
Analysis of Hybrid Energy System
Mojtaba Abbasi,
Tomsk Polytechnic University
Abstract: This paper focuses on response analysis of Microgrid which consists of wind turbines, photovoltaic
panels, with Hybrid DC and AC Buses. In grid-connected operation, voltage of DC bus is kept steady by the
inverter. Energy Management System controls hybrid storage system to release or absorb power with the
strategies according to grid condition, state of charge of batteries and super-capacitor, electricity price and so
on. In islanded operation, voltage of DC bus is controlled by storage system and amplitude and frequency of AC
Bus voltage are regulated by parallel inverters with voltage-frequency or droop control strategy. In this work,
different control strategies in grid-connected and islanded operation are described which can keep power
balanced and AC/DC bus stable. A test case of Permanent Magnet Synchronous Generator connected to a
rectifier and inverter has been simulated in MATLAB/Simulink environment and from the results it can be
shown that the voltages of AC and DC buses have been maintained steadily. The output voltage from PV
modules is lifted using boost converter and given to maximum power point tracking system. The output is
connected in parallel with the input from wind system to a common inverter and given to a common load. The
desired outputs, power, voltage and current of AC side is observed and maintained within rated values.
I. Introduction
Now more and more photovoltaic panels and wind turbines are integrated into grid, whose power
fluctuation will lead to grid instability. Microgrid system is one of the solutions. There are many benefits of
Microgrid including little pollution, higher reliability, better quality of power supply, and higher efficiency. This
research presents hybrid DC- and AC-bus Microgrid system, which can be established in a country or island.
To avoid global warming, the consumption of fossil fuels must be reduced. Hence, the installation of
renewable energy power production plants has become a burning issue not only for isolated islands but also all
over the world. Among various renewable energy systems, photovoltaic power generation systems (PV systems)
and wind power source are expected to play an important role as a clean electricity power source in meeting
future electricity demands. Photovoltaic (PV) power as an alternative energy resource has been becoming
feasible due to Enormous research and development works being conducted. The use of Photovoltaic (PV)
generators in isolated sites, where conventional generation is not practical, can pose a problem because PV
output power depends on weather conditions and cell temperature, making it an uncontrollable source.
Furthermore, it is not available during the night. We consider resolving this problem by installing a hybrid
system using an alternative wind energy source along with the PV array. Solar arrays provide dc power.
Hence power from a solar array cannot be directly added to an isolated power utility for using directly
in residential, industrial or commercial applications. We require a DC-DC converter to step up the dc voltage
from the panel and then an inverter to convert the dc into ac power which can be fed to the utility. A
Photovoltaic (PV) system‟s power output is not constant and fluctuates depending on weather conditions
(variations in irradiation and temperature). Therefore we also require a Maximum Power Point tracker (MPPT)
along with the DC-DC converter in order to obtain the maximum power output from the Solar Photovoltaic
(PV) array. In the hybrid system a wind power generators along with PV generators feeds the utilities loads.
The response of the hybrid system following common disturbances such as solar insulation variations
and load changes have to be is investigated for analyzing the effects fluctuating power causes in the isolated
power utility. This study is essential for devising a method for leveling the fluctuations in a PV system's power
output when large output power from several PV systems has to be penetrated in the utility.
II. Hybrid Power System
A. Isolated Power Utility
This research presents hybrid DC- and AC-bus Microgrid system, as shown in Fig 1, which can be established
in a country or island.
There are many units in the system which can be used in a house of a country. All the renewable
energy generations and storage devices in the house are connected to DC bus with different converters which
can supply power to local DC loads. Inverters are used to transfer power between AC and DC buses. Common
and sensitive loads can be connected to AC bus with different coupling points. If there are some faults happened
in utility grid, Microgrid system can work in islanded operation. In worse condition, if renewable energy
generations can‟t supply enough power for local

Analysis Of Hybrid Energy System
Figure 1 Microgrid systems with hybrid DC and AC buses
Loads and state of charge of storage devices are in low level, Microgrid could cut common loads to
keep supplying power to sensitive loads. In hybrid DC- and AC-bus Microgrid system, fewer inverters are
needed. So control strategy for parallel inverters is easier in islanded operation. And DC loads can be connected
to DC bus directly without rectifier. Also the system can isolate individual units if there is something wrong in
the unit.
B. Pv-Wind Hybrid Power System
The PV-Wind hybrid system model consisting of a wind turbine, PV power generation systems, and a
load is shown in detail in Fig. 2,
Fig. 2 Isolated hybrid power system model.
One unit of the Microgrid system is established in the lab as shown in Figure 2. It consists of a wind
turbine, photovoltaic panels, batteries series connected and super-capacitor. The stability of DC- and AC-bus
voltage is very important. When Microgrid system is connected to the utility grid, the amplitude of DC-bus
voltage (200V) is regulated by the inverter, and voltage of AC bus is the same with the utility grid. However
when the Microgrid works in islanded operation, DC-bus voltage must be regulated by renewable energy
generations and storage devices, and the voltage and frequency of AC bus are controlled with voltage-frequency
or droop control strategy of parallel inverters
III. Modeling Of Pv Array
A. Modeling Of Pv Cell
The equivalent circuit of the ideal PV cell is shown in Fig 3. The ideal PV cell be modulate as diode
parallel with a current source
Fig 3 Ideal PV Cell

Thebasic equation from the theory of semiconductors that mathematicallydescribes the I–V
characteristic of the ideal PV cellis
(1)
Where, (2)
Therefore, (3)
Where, Ipv,cellis the current generated by the incident light (it is directly proportional to the Sun
irradiation), Id is the Shockley diode equation, I0,cellis the reverse saturation or leakage current of the diode, q is
the electron charge (1.60217646 × 10−19 C), k is the Boltzmann constant (1.3806503 × 10−23 J/K), T (in
Kelvin) is the temperature of the p–n junction, and a is the diode ideality constant. The origin of I-V curve from
the equation (2) is shown in fig 4.
Fig 4 Origin of I-V equation of an Ideal PV cell
In addition to this modeling, the PV array is also modeled. With the help of this the amount of power
which is produced through the solar cell can be estimated in a clear manner.
Boost Converter
A. Modes Of Operation
In a boost converter, the output voltage is greater than the input voltage-hence the name “boost”. A
boost converter is shown in Fig 5.
Fig 5 Boost Converter Circuit
The circuit operation can be divided into two modes. Mode 1 begins when the MOSFET M1 is
switched on at t=0. The input current, which rises, flows through inductor L and MOSFET M1. Mode 2 begins
when the MOSFET M1 is switched off at t=t1. The current that was flowing through the MOSFET would now
flow through inductor L, capacitor C, load and Diode Dm. The inductor current falls until MOSFET M1 is turned
on again in the next cycle. The energy stored in the inductor L is transferred to the load. The equivalent circuits
for the two modes of operation are shown in Fig 6.
Fig 6. Equivalent Circuits

The waveforms for voltages and currents are shown in Fig 7 for continuous load current, assuming that
the current rises or falls linearly.
Fig 7 Current and Voltage waveforms
Assuming that the inductor current rises linearly from I1 to I2 in time t1,
(4)
(5)
and the inductor current falls linearly from I2 to I1 in time t2,
(6)
or (7)
Where, ∆I = I2-I1 is the peak-to-peak ripple current of inductor L.
From equations (5) and (7),
(8)
Substituting t1=kT and t2= (1-k)T yields the average output voltage,
(9)
Which gives
(10)
Assuming a lossless circuit, VsIs = VaIa and the average input current is
(11)
The switching period T can be found from
(12)
And this gives the peak-to-peak ripple current:
(13)
When the MOSFET is on, the capacitor supplies the load current for t=t1. The average capacitor current
during the time t1 is Ic=Ia and the peak-to-peak ripple voltage of the capacitor is
Substituting t1 = (Va – Vs)/(Vaf),
(14)
B. Inverter In A Pv System
The principle of a stand-alone inverter used in a PV-Diesel hybrid system can be explained with
reference to the single-phase equivalent shown in Fig 8.The inverter has a full-bridge configuration realized
using four power electronic switches (MOSFET or IGBTs) S1, S4. In this scheme, the diagonally opposite
switches (S1, S4) and (S2, S3) are switched using sinusoidal pulse-width modulated gate pulses. The inverter
produces sinusoidal output voltage. The inductors X1, X2 and the ac capacitor C2 filter out the high-switch-

frequency components from the output waveform.
Fig. 8 Inverter in a PV system
Most inverter topologies use a low-frequency (50 or 60 Hz) transformer to step up the inverter output
voltage. In this scheme, the diesel generator and the converter are connected in parallel to supply the load. The
voltage sources, diesel and inverter, are separated by the link inductor Xm. The bidirectional power flow
between inverter and the diesel generator can be established. The power flow through the link inductor, Xm, is
Sm = Vm Im (15)
Pm= (VmVcsinXm (16)
Qm=(Vm/Xm)(VmVccos
Whereis the phase angle between the two voltages. From Eq.(16), it can be seen that the power supplied by
the inverter can be controlled by controlling the phase angle. The PWM pulses separately control the
amplitude of the converter voltage, Vc, while the phase angle with respect to the diesel voltage is varied for power
flow.
Wind Turbine
The synchronous generator is currently used in WECS, especially in law power for battery charging,
for example. But the use of PMSG in high power generation is recent. It‟s facilitated by the technologic progress
realized in power electronics and permanent magnet materials used in generator rotors. The use of PMSG allows
to eliminate the gearbox and to operate at variable and low speed; which is adequate with wind speed nature.
Variable speed operation of wind energy conversion system contributes to decrease the mechanical
stress and acoustic noise and offers possibility to control of active and reactive powers; the PMSG is connected
to the grid via two power electronics converters with an intermediate DC link bus. The generator side converter
is controlled via hysteresis regulation of generator currents with zero direct current; in order to obtain a maximal
torque for a minimal current.
The MPPT algorithm is used to determinate the optimal rotational speed reference for any value of
wind speed under the nominal regime in order to maximizing power captured by the wind turbine. The grid side
converter is controlled by pulse width modulation (PWM) obtained from proportional integral (PI) regulation of
currents sanded to the electrical grid. The DC link voltage is kept at constant value with a DC/DC converter and
PI regulation of DC voltage at its reference. Power limitation for high wind speed values is achieved by varying
the blade angle (Pitch control) which corresponds to decrease in power coefficient.
Figure 9. Control diagram of wind turbine
The speed reference allows to maximizing the power captured by the wind (MPPT strategy) is given
by:
(18)

When the wind speed reached the nominal value, the pitch angle regulation (based on fuzzy logic
algorithm) enter in operation in order to decrease the power coefficient. The simplified representation of wind
turbine control diagram is shown in Figure 9.
Grid Connected Operation
Micro grid works in grid-connected operation. In this case, the wind and solar generators should work
in Maximum Power Point Tracking (MPPT) strategy to get higher energy efficiency. In order to reduce the
influence of fluctuation to utility grid, energy storage system should be controlled to supply the power
difference between renewable energy generations and loads.Fig 10.
Pstorage = Pbatt + Psc
= Pwind + Psolar – P load (19)
 Pstorage is the total power of storage system including batteries and super-capacitor.
 Pbattand Psc are power released from battery and super-capacitor resp
 Pwind is generated by wind turbine.
 Psolar is generated by photovoltaic panels.
 Pload is power absorbed by DC and AC loads.
Figure 10. Power Flow in the system
In grid-connected operation voltage of DC bus is controlled by inverter and amplitude and frequency of
AC-Bus voltage are the same with utility grid. When power from renewable energy generations is fluctuant or
loads change quickly, hybrid storage system including batteries and super-capacitor must absorb or release
power difference very fast. According to the character of different storage devices, high frequency power is
released or absorbed by super-capacitor
Simulation Results
Integration Of Pv Array With Boost Converter And Pwm Inverter
The integrated circuit for simulation of PV array, boost converter and PWM inverter with MPPT is
shown Fig 11, the voltage and current output waveforms are shown in Fig.12 and the power output shown in Fig
13.
Fig 11. Integrated PV array – boost converter – PWM inverter circuit
Fig 12. PWM Inverter output voltage and current

Fig 13. PWM Inverter output power
Step change in insulation was mentioned in literature as the source of power fluctuations. Fig
14.shows the integrated circuit for simulation of a step change in insulation from 800 W/sq.m. to 1000 W/sq.m.
The output waveforms are also shown.
Fig 14. Integrated circuit for simulation of a step change in insulation
Fig 15. Step change in insulation
The step change in insulation is shown in fig 15.. Here the insulation changes from 800 to 1000 at the
5th
second.
Fig 16. Integrated circuit power output for a step change in insulation
Fig 16. Shows the change in current and voltage waveforms. Followed by the step change in insulation
at the 5th
second the voltage and current magnitude increases.
Figure 17. Integrated circuit voltage and current output for a step change in insulation

Fig 17.Shows the variation of power after the step change in insulation.
Integration Of Wind And Solar
Figure18.Integration of wind and solar
The power obtained from the solar and the wind energy conversion systems are given to an inverter as
shown in Fig 18.
Figure 19. Output voltage and current of pv-wind
The voltage and current waveforms obtained at the inverter ends are shown in Fig 19.
Figure 20. Combined output power of two PV plants and wind turbine
IV. Conclusion
This paper aims at implementing a PV Wind, hybrid system connected to an isolated power utility. The
basic concepts of solar array, DC-DC boost converter, PWM inverter, Wind turbine are discussed. The modeling
methods of all components of the hybrid system are described. Simulation studies are done for the standard test
conditions using MATLAB/Simulink. The response of a PV - Wind hybrid system connected to an isolated
power utility following common disturbances such as solar insulation variations and wind speed change and
load changes were simulated to understand the power fluctuation caused.
The results of the simulation are analyzed to understand the significance of the power fluctuation
caused, so that a method for leveling the fluctuations in a PV system's power output when large output power
from several PV systems has to be penetrated in the utility could be defined.

References
[1]. Joe-Air Jiang, Tsong-Liang Huang, Ying-Tung Hsiao, Chia-Hong Chen, „Maximum Power Tracking for Photovoltaic Power
Systems‟, Tamkang Journal of Science and Engineering, vol. 8, no 2, pp. 147-153, 2005.
[2]. Marcelo Gradella Villalva, Jonas Rafael Gazoli, and Ernesto Ruppert Filho, „Comprehensive Approach to Modeling and Simulation
of Photovoltaic Arrays‟, IEEE Transactions on Power Electronics, vol.24, no. 5, 2009.
[3]. Muhammad H. Rashid, „Power Electronics Circuits, Devices, And Applications‟, Third Edition, Prentice Hall of India Pvt. Ltd.
[4]. Kundur, „Power System Stability and Control‟, McGraw-Hill,Inc, 1994.
[5]. Bhadra, S.N., Kastha, D., Banerjee, S., „Wind Electrical Systems‟, Oxford University Press.
[6]. Fitzgerald, A.E., Kingsley, C., „Electric Machinery‟, McGraw-Hill,Inc.
[7]. Roy, S., Malik, O. P. and Hope G. S., “An adaptive control scheme for speed control of diesel driven power plants”, IEEE
Transactions on Energy Conversion, Vol.6., No.4, 1991.
[8]. Kuang, B., Wang, Y. and Tan, Y.L., “An H∞ Controller Design for Diesel Engine Systems”, IEEE Transactions on Industry
Applications, Vol., No., 2000.
[9]. Augustine, D. W. and Kumar, K.S. P., “A method for self-tuning a PID controller for control of small to medium sized diesel
engines”, IEEE International Conference on System Engineering, P.85-88 1-3 Aug. 1991.
[10]. Ashari M., Nayar C.V., Islam S., “Steady-state performance of a grid interactive voltage source inverter”, IEEE Power Engineering
Society Summer Meeting, 2001. Vol. 1, P.650 -655 July 2001
[11]. Nayar C.V., Ashari M., Keerthipala, W.W.L., “A grid-interactive photovoltaic uninterruptible power supply system using battery
storage and a back up diesel generator, IEEE Transaction on Energy Conversion, Vol.15, Issue 3, Ps. 348 - 353, Sept. 2000 .
[12]. Bilbao, E.; Gaztanaga, H. Mir, L. Etxeberria-Otadui, I. Milo, A. “Design and development of a supercapacitor-based microgrid
dynamic support system,” in Power Electronics and Applications, 2009. EPE '09. 13th European Conference on, 2009, pp. 1-10.
[13]. Boroyevich, D. and Cvetkovic, I., “Future Electronic Power Distribution Systems– A contemplative view,” Optimization of
Electrical and Electronic Equipment (OPTIM), 2010 12th International Conference on, pp. 1369-1380.
[14]. C. Abbey, G. Joos, ”Supercapacitor Energy Storage for Wind Energy Applications”, IEEE Trans. Ind. Electron., vol.43, iss.3,
pp.769-776, May 2007
[15]. Erickson, M.J. and Lasseter, R.H.: “Integration of battery energy storage element in a CERTS microgrid”, Energy Conversion
Congress and Exposition, 2010, pp. 2570-2577
[16]. Taljan, M. Fowler, C. Cañizares, G. Verbič: Hydrogen storage for mixed wind–nuclear power plants in the context of a Hydrogen
Economy, Hydrogen Energy, vol. 33, iss 17, pp. 4463-4475, Sep. 2008.
[17]. Kanchev, H., Lu, D., Francois, B. and Lazarov, V.: “Smart monitoring of a microgrid including gas turbines and a dispatched PV-
based active generator for energy management and emissions reduction”, Innovative Smart Grid Technologies Conference Europe
(ISGT Europe), 2010 IEEE PES, pp. 1-8.
[18]. R. Cardenas et al: Control Strategies For Power Smoothing using a Flywheel Driven by a Sensorless Vector-Controlled Induction
Machine Operating in a Wide Speed Range, IEEE Trans. Ind. Electron., vol 51, pp. 603 - 614, 2004.
[19]. R. Majumder, G. Ledwich, A. Ghosh, S. Chakrabarti, and F. Zare, “Droop control of converter-interfaced microsources in rural
distributed generation,” IEEE Trans. Power Del., vol. 25, no. 4, pp. 2768-2778, October 2010.
[20]. R.Majumder, G. Ledwich, A. Ghosh, S. Chakrabarti, and F. Zare, “Droop control of converter-interfaced microsources in rural
distributed generation,” IEEE Trans. Power Del., vol. 25, no. 4, pp. 2768-2778, October 2010
[21]. D. Salomonsson, L. Söder, and A. Sannino, “An adaptive control system for a DC microgrid for data centers,” IEEE Trans. Ind.
Appl., vol. 44, no. 6, pp. 1910-1917, November/ December. 2008.

C011141018

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to C011141018 (16)

More from IOSR Journals (20)

Recently uploaded (20)

C011141018