Design & Simulation of Half Adder Circuit using AVL Technique Based on CMOS Technology

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 04 Issue: 08 | Aug -2017 www.irjet.net p-ISSN: 2395-0072
© 2017, IRJET | Impact Factor value: 5.181 | ISO 9001:2008 Certified Journal | Page 1630
Design & Simulation of Half Adder Circuit Using AVL technique
based on CMOS Technology
1 2 3
1M.Tech Student, Dept. of Electronics & Communication, N.I.E.T Greater Noida, Uttar Pradesh, India
2,3 Assistant Professor, Dept. of Electronics & Communication, N.I.E.T Greater Noida, Uttar Pradesh, India
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - Power optimization is a technique used in
low voltage applications. Arithmetic circuits play a crucial
role in designing of any VLSI system. In this paper,
Arithmetic circuits are designed using Adaptive Voltage
Level (AVL) techniques. This technique consumed less
power as compare to conventional design. Total power
dissipation is reduced by applying the AVLS (adaptive
voltage level at supply) technology in which the supply
potential is increased and AVLG (adaptive voltage level at
ground) in which the ground potential is raise. This paper
shows how we can control power using AVL techniques.
The AVL technique based on Arithmetic circuit is compared
to conventional design which is based on total power
consumption, propagation delay, layout area, speed and
is more preferred.. The result indicates that the significant
reduction in power consumption of this proposed cell with
the AVL technique. This design is better in designing the
system that consumed less power. All the circuits are
simulated on tool Micro Wind 3.1 and DSCH in 65
nanometer CMOS technology.. This technique reduces the
total power dissipation by applying the adaptive voltage
level at ground (AVLG) technology in which the ground
potential is raised and adaptive voltage level of supply
(AVLS) in which supply potential is increased. The main aim
of the design is to investigate the power dissipation, power
delay product, layout area, routing wires for Arithmetic
circuit for the proposed design style. The simulation results
shows that in all the technique AVL technique is more
preferred because it takes less power consumption, delay
,fast response as compared to other techniques.
Key Words: Arithmetic circuits, AVL techniques, Low
Power, High Speed, VLSI
1. INTRODUCTION
The simplest combinational circuit which performs the
arithmetic addition of two binary digits is known as half
adder.. It is the necessary building block for designing any
VLSI system. Figure 1.1 shows the logic diagram of half
adder. Table 1.1 represents truth table of half adder. It
adds two inputs and produces the two outputs in the form
of sum and carry. The sum is 1 when either of the input is
one. The sum is 0 when both the inputs are 0 or
Carry is one when both the inputs are 1. From the truth
table the logical expression of sum output can be written as
a sum of product expression by summing the inputs for
which the sum is 1. S = A'B + AB' this expression can be
simplified as XOR form
S = A ⨁ B
Carry output can be written as product of sum expression
for which the carry is 1. Cout = AB
1.1 Related Work
There are many papers that have been published for
reducing the power consumption of the arithmetic circuits
such as half adder, Full adder, Comparator and half
subtractor. All are based on different methodologies for
various Logic style. In such papers they have designed the
circuit by using various logic design style Complementary
Pass Transistor design style, Transmission Gate design
style, Hybrid CMOS design style, Bridge design style and
many more design style. All these designs are modified by
using the technique adaptive voltage level .It has two
types. The first is AVLG technique in which the ground
potential is raised and second is AVLS technique in which
supply potential is increased. By using AVL technique
various parameter like power consumption, layout area,
propagation delay, and power delay product are reduced.
.The main drawback using AVL technique is the number of
routed wires is increased.
1.2 Proposed Half Adder Design Style
In the proposed design of Half Adder the circuit is design
via XOR/XNOR & Transmission Gate design style as hybrid
design and introduces this conventional design
, Surya Deo Choudhary , Ashutosh kr.SinghMateshwar Singh

with AVL techniques. Variation in technology scaling
introduces the variation in parameters values. If the
technology is reducing more & more than the desired
system would be more suitable for low power, low
propagation delay and high performance. For these
performance AVL techniques such as AVLG (adaptive
voltage level at ground) technique in which the ground
potential is raised and AVLS (adaptive voltage level at
supply) technique in which supply potential is increased.
For this design total number of 09 transistors is required
for the operation of Half Adder. As compared to the other
design style the proposed AVL technique has the following
advantages such as low power dissipation, low
propagation delay, less No. of transistors, less Layout
area, high performance and less PDP . So that this design
style makes the Half Adder more efficient .The most
affected design is via AVLS technique.
1. CMOS IMPLEMENTATION OF HALF ADDER CIRCUIT
The circuit is designed using CMOS as combination of Pull-
up and Pull-down networks. The function of the Pull-
up network is to provide a connection between the
output and VDD when the output of the logic gate is meant
to be
1. The function of the PDN is to connect the output to
VSS when the output of the logic gate is meant to be 0.
16 numbers of transistors are needed for the
implementation of half adder using CMOS. Figure shows
the circuit diagram of Half Adder using CMOS design
style. This design has numerous disadvantages such as
more power consumption, propagation delay, routing
wires and layout area. So this design is not widely used
due to complex structure. Layout cell, Simulation result,
MOS characteristic and Variation of Power Vs Supply
voltage is shown in Fig
Fig2.1: Circuit Diagram of Half Adder using CMOS Design
Fig2.2: Layout cell of Half Adder using CMOS Design
Fig2.3: Simulation Waveform of Half Adder using CMOS
design
Fig2.4: Variation of Power Vs Supply voltage of Half Adder
using CMOS
Conventional Design of Half Adder
In conventional design of Half Adder the circuit in
designed using Transmission Gate & XOR/XNOR based.
Design style that requires less no. of transistors. Figure
shows the circuit diagram of conventional design of Half
Adder. This design requires only 6 transistors to
implement the Half Adder. It requires 3 PMOS and 3
NMOS transistor to implement the Half Adder which is
very less as compared to CMOS half Adder Design. The cell
layout design of conventional half adder is simulated by
Microwind 3.1 software at 65 nm technology at Vdd = 1.0
V at Temp. 27° C .this design consumes less power,
propagation delay, layout area, routing wires, PDP as
compared to CMOS Half Adder. Layout cell, Simulation
result, MOS characteristic and Variation of Power Vs
Supply voltage is shown in Fig

3.3.1 AVLG Technique
Fig3.1: Circuit Diagram of Conventional Half Adder
Fig3.2: Layout Cell of Conventional Half Adder
Fig3.3: Simulation Waveform of Conventional Half Adder
Fig3.4: Variation of Power Vs Supply voltage of
Conventional Half Adder
3.3 Design of Half Adder using AVL Technique
Adaptive voltage level technique is used to reduce
the power consumption, propagation delay, layout area,
PDP as compared to CMOS and conventional Half Adder
design. In AVLS technique an additional control circuit is
used at the upper end of the circuit to bring down the
supply voltage. In AVLG technique control circuit is used
at the lower end of the circuit to lift the ground potential
of conventional half adder circuit.
In AVLG technique, a combination of1 N-MOS &2 P-MOS
circuits are connected in parallel. An input clock pulse is
applied to the N-MOS of circuit of AVLG and all the P-MOS
are connected to ground. This AVLG circuit is connected at
the ground terminal of conventional one by removing
ground. It would lift the ground potential of the circuit to
reduce the power consumption of the conventional half
adder design. Depending upon the input signal the output
also varied and the usage of clock pulse is to prevent any
defect in half adder during power consumption. The cell
layout design of conventional half adder using AVLG
technique is simulated by Microwind 3.1 software at 65
nm technology at Vdd = 1.0 V at Temp. 27° C .this design
consumes less power, propagation delay , layout area ,
PDP as compared to CMOS and conventional Half Adder.
Layout cell, Simulation result, MOS characteristic and
Variation of Power Vs Supply voltage is shown in Fig.
Fig4.1: Circuit Diagram of Half Adder using AVLG Technique
Fig4.2: Layout cell of Half Adder using AVLG Technique

Fig4.3: Simulation Waveform of Half Adder using AVLG
Technique
using AVLG Technique
AVLS Technique
In AVLS technique, a combination of 2- N-MOS & 1-P-MOS
are connected in parallel. So that a input clock pulse is
applied at the P-MOS of circuit of AVLS circuit and the rest
of the NMOS transistor is connected to the drain terminal.
This approach is more valuable for reducing the power
consumption also for the leakage current. . This AVLS
control circuit is placed at voltage supply source terminal
of the conventional half adder design in which supply is
given through this control circuit. This control circuit at
the upper end would bring down the supply voltage
given to the whole circuit in order to reduce the
power consumption of the conventional half adder design.
When the input is varied corresponding output will be
produced. It would reduce the leakage power by reducing
the gate to source voltage and gate to drain voltage. This
design would be responsible for very low power
consumption.. The cell layout design of conventional half
adder using AVLS technique is simulated by Microwind
3.1 software at 65 nm technology at Vdd = 1.0 V at
Temp. 27° C .This design consumes less power,
propagation delay, layout area, PDP as compared to Half
Adder using CMOS, conventional and AVLG Technique.
Layout cell, Simulation result, MOS characteristic and
Variation of Power Vs Supply voltage is shown in Fig
Fig5.1: Circuit Diagram of Half Adder using AVLS Technique
Fig5.2: Layout cell of Half Adder using AVLS Technique
Fig5.3: Simulation Waveform of Half Adder using AVLS
Technique
using AVLS Technique

RESULT REFERENCES
[1]. Farshad Moradi, Dag T. Wisland, Ali Peiravi , Hamid
Mahmoodi (2008)1-Bit Sub Threshold Full Adders in
65nm CMOS Technology International conference on
Microelectronics 1- 4244-2370-5/08/$20.00 ©2008
IEEE
[2]. S. Wariya, Himanshu Pandey, R. K. Nagaria and
S. Tiwari ,(2010)Ultra low voltage high speed 1bit adder,
IEEE Transactions Very Large Scale Integeration.
[3]. Praveer Saxena, Dinesh Chandra, Sampath Kumar
V(2011) Design of 1-Bit Full Adder for Low Power
Applications IJAEST,Vol No. 10 Issue No.1,019-025
[4]. Shamima Khatoon (2012)A novel design for highly
compact low power area efficient 1-bit Full Adders
,IJAET
[5]. Keivan Navi and Omid Kavehei(2008)Low- Power and
High-Performance 1-Bit CMOS Full- Adder Cell
JOURNAL OF COMPUTERS, VOL. 3, NO. 2, FEBRUARY
2008
AUTHOR’S BIOGRAPHY
CONCLUSIONS
From the above result we can see that the simulation
result of this half adder using Adaptive Voltage Level
technique shows that the power consumption is much
reduced as compared to other techniques .Propagation
delay, layout area, PDP also reduced as compared to
other technique. It also requires less routed wires as
compared to CMOS design. Various parameters have
been calculated by using Micro wind 3.1 at 65 nm
technology. Design of Half Adder using AVLS technique is
more efficient in speed, layout area, power
consumption, routed wires and propagation delay as
compared to other technique. All the circuits operate at
supply voltage of 1.2 V and temp. of 27°C.By using AVL
technique size of circuit is also reduced. The application of
AVL technique is used to reduce the power dissipation of
digital circuits. By using AVL technique power can be
saved up to 60 %.
Mateshwar Singh received his B. Tech
Degree in Electronics and Communication
Engineering from H.C.S.T Farah Mathura
and he is pursuing M.Tech in VLSI Design
from NIET Greater Noida.
Surya Deo Choudhary has received his
Ph.D. degree in Electronics & Communication
Engineering from B.R. Ambedkar Bihar
University in 2015. He has received his
M.Tech. degree from BIT Sindri, Dhanbad in
2011 and B.Tech. in 2008.
He is working as an Assistant Professor in
Department of Electronics and
Communication Engineering at Noida
Institute of Engineering and Technology,
Greater Noida. He has published many
International and National Journals. His area
of research is Antenna & Microwave,
Passive Filters.
Ashutosh Kumar Singh has 8 years of
Teaching Experience and currently working
as an Assistant Professor in Department of
Electronics and Communication Engineering
at Noida Institute of Engineering and
Technology, Greater Noida.
He has completed his Masters in VLSI Design,
2013 and B.Tech in Electronics and
communication Engineering, 2009 from
Uttar Pradesh Technical University,
S.
No. Parameters C-CMOS Conventional
AVL
G AVLS
1. Power
Consumption
(µw)
7.348 0.502 0.383 0.321
2. Routed Wires 50 14 35 30
3. Compiled Cells 16 / 16 6 / 6 9 / 9 9 / 9
4.
Layout Area
2
(µm ) 232 96 136 128
5.
Propagation
Delay (ns) 0.70 0.67 0.65 0.54
6. PDP (fj) 5.1436 0.33634 0.2485
0.173
34
7.
No. of N-MOS
and P- MOS
transistors
8, 8 3, 3 5,4 4 ,5

Lucknow. He has also worked with APS,
Achen, Germany and completed his training
in Applied Robotic Control. He has
published papers in International and
National Journals & conferences. His areas of
research are Low Power VLSI Design,
Automation and Robotics.

Design & Simulation of Half Adder Circuit using AVL Technique Based on CMOS Technology

More Related Content

What's hot (20)

Similar to Design & Simulation of Half Adder Circuit using AVL Technique Based on CMOS Technology (20)

More from IRJET Journal (20)

Recently uploaded (20)

Design & Simulation of Half Adder Circuit using AVL Technique Based on CMOS Technology