IRJET- Note to Coin Converter using Digital Image Correlation Technique in Image Processing

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 05 Issue: 03 | Mar-2018 www.irjet.net p-ISSN: 2395-0072
© 2018, IRJET | Impact Factor value: 6.171 | ISO 9001:2008 Certified Journal | Page 1860
Note to Coin Converter Using Digital Image Correlation Technique in
Image Processing
Nirmit Patade1, Ravi Patel2, Vivek Gupta3, Jitendra Patra4, Prof. Rajesh Khotre5
1,2,3,4 Student, Electronics & Telecommunication, PVPPCOE, Mumbai
5Professor, Electronics & Telecommunication, PVPPCOE, Mumbai
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract -The need of coins has been increased nowadays.
We require coins at various public places regularly in our
daily lives. Places such as petrol pumps, bus stops, railway
station, malls, parking spaces, parks and even in rural areas
coins are extensively used. Use of coins has been increased
more instead of note in various places thus a system which
will give us coins in exchange of notes using image processing
will turn out to be very useful.
Key Words: Note To Coin Converter, Image Processing,
MATLAB, Digital Image Correlation.
1. INTRODUCTION
Aswe require coinsat many public placesandquiteoften
we don’t have the required change, a system that will giveus
coins in exchange of note will be of great use.
The note to coin converter will check the originality of
note using image processing technique. The preferable
technique to use would be digital image correlation
technique. The note is detected using MATLAB algorithm
and the result is given to the microcontroller which willturn
on the respective relays and motors of coin dispensing unit.
The user will use a keypad to select how many coins of what
value are needed.
Using a coin dispensing unit, coins will be provided to
the user. The microcontroller will operate the DC motors to
Provide the coins.
2. ARCHITECTURE
2.1 Camera
The note should be placed in a dedicated slot where a
camera will take a picture of it. The background should be
dark so that the note will be clearly distinguished from the
background. The picture will be further converted into a
frame. The frame will be sent to the MATLAB for
preprocessing.The camera shouldtake a clearpicturesothat
the MATLAB processing will be accurate.
2.2 Computer
The computer will use MATLAB to compare the image of
the note with the image of the note stored in the database.
The digital image correlation technique will be used to
compare the two images. In image correlation technique
each aspect of the note is compared with the image in the
database. If the two images match then the note will be
considered as real.
2.3 USB to TTL
The USB to TTL Serial cables are used to provide
connectivity between USB and serial UART interfaces. The
computer is connected to the microcontroller using a USB to
TTL. Once the computer authenticates the entered note, it
will command the microcontroller using USB to TTL to
perform the requiredoperation. Driversmust be installedon
the computer so that the computer will be able to detect and
process the data signals.
2.4 RFID Reader
Passive RFID tags doesnot have internal powersource.A
passive RFID transponder consists only of a microchip and
an antenna. The two are together called as an RFID inlay.

Passive tags wait for a signal from an RFID reader. Once the
tag is within range of the RFID reader, the RFIDtag’santenna
draws energy from the electromagnetic waves. Once the
tag’s microchip is powered, it transmits a signal.
The change in the electromagnetic wave is detected by
the reader’s antenna which interprets the information. The
antennas in both the tag and reader must be within several
meters of each other. The read range depends on several
factors such as the equipment settings, transmit frequency,
and environmental factors.
The passive RFID tag will be used at the administrative
end. It will provide access to enter new coins in the coin
stack.
Passive RFID tags generally operate at three
frequencies:
• Low Frequency- 125 kHz to 134 kHz
• High Frequency- 13.56 MHz
• Ultra High Frequency- 856 MHz to 960 MHz
2.5 Microcontroller
The microcontroller we are using is AT89C2052. The
microcontroller will operate the coin dispensing unit along
with the DC motors and LCD. The keil software will be used
to burn the program into the microcontroller.
The AT89S52 is a 40 pin, low-power, high-performance
CMOS 8-bit microcontroller with 8K bytes of in-system
programmable Flash memory.
2.6 Power Supply
The power supply converts A.C into D.C, and alsoprovides
output voltage of 5 volts, 1 amp. The important components
of the power supply are:
•TRANSFORMER:
It transforms the voltage level from one level to another.
Transformer used is the step down transformer
•RECTIFIER:
The rectifier is used to convert A.C to D.C voltage. We have
used a bridge rectifier.
•FILTER:
A filter circuit is a device, which removes ac component of
rectified output but allows the dc component to reach the
load.
•REGULATOR:
A voltage regulator is a circuit that supplies a constant
voltage regardless of changes in load current. We have used
IC7805 as the regulator.
2.7 LCD
LCD stands for Liquid Crystal Display. It is a display
module and is widely used. A 16x2 LCD display is used in
various devices and circuits. LCDs are economical, easily
programmable and can even display special & custom
characters..A 16x2 LCD means it can display 16 characters
per line and there are 2 lines. Here each character is
displayed in 5x7 pixel matrix.
The LCD will be used for user interaction.Theauthenticity
of the note and the number of coins left in the coin stack will
be displayed through LCD.
2.8 Motor Driver
L293D is a Motor driver or Motor Driver IC. It allows DC
motor to drive on either direction. L293D is a 16-pin IC. It
can control a set of two DC motors simultaneously in any
direction. That means you can control two DC motor with a
single L293D IC.
2.9 Coin Dispensing Unit
Sample The coin dispensing unit will consist of 4 trays
containing coins of 1 rupee, 2 rupee, 5 rupee, 10 rupee. DC
motors will be used to dispense coins out of the system .If
the coins are not sufficient the LCD will display “Insufficient
coins”.

3. FLOWCHART
3. CONCLUSION
This is an efficient system which provides us coins in
exchange of notes and reducesthe human effort. The system
uses a camera and a computer to recognize the note and
authenticate it using MATLAB. The note to coin converter
can be used at various public places such as petrol pumps,
malls, parks and parking spaces, etc.
4. FUTURESCOPE
The system can be further designed in a manner suchthat
it will provide us Indian currency in exchange of foreign
currency. It will function as an excellent currency exchange
system.
REFERENCES
[1] Angelo Frosini, Marco Gori, “A Neural Network-Based
Model for Paper Currency Recognition andVerification,”
IEEE Transaction on NN Vol.7 No. 6
[2] A. Bade and D. Aher, “Note to Coin Exchanger Using
Image Processing ,” IJRITCC, vol. 1, Mar. 2013, pp. 154-
158
[3] Prof. Madha Thigale, Lina Ladhane,MadhuriMangutkar,
Neha Gaikwad “Note to Coin converter using Digital
Image Processing” IRJET, Volume: 04 Issue: 03 ( Mar -
2017)
[4] www.microchip.com/wwwproducts/en/AT89s52
[5] www.Wikipedia.org

IRJET- Note to Coin Converter using Digital Image Correlation Technique in Image Processing

More Related Content

What's hot (20)

Similar to IRJET- Note to Coin Converter using Digital Image Correlation Technique in Image Processing (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Note to Coin Converter using Digital Image Correlation Technique in Image Processing