Mathematical Relationships between the Compressive Strength and Some Other Structural Properties of Sand-Quarry Dust Blocks

IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE)
e-ISSN: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 1 Ver. III (Jan- Feb. 2015), PP 93-97
www.iosrjournals.org
DOI: 10.9790/1684-12139397 www.iosrjournals.org 93 | Page
Mathematical Relationships between the Compressive Strength
and Some Other Structural Properties of Sand-Quarry Dust
Blocks
C. U. Anya1
and N. N. Osadebe2
1
Federal University of Technology, Owerri, Nigeria
2
University of Nigeria, Nsukka
Abstract: This work developed mathematical relationships between the compressive strength and some other
properties of sand quarry dust blocks notably water absorption, flexural strength and split tensile strength.
Regression analyses were performed on data obtained from tests on appropriate specimens prepared using
fifteen different mix ratios. The cement/combined aggregate ratio ranged from 1: 6 to 1: 10 with the percentage
of quarry dust being 10 to 40 % of the combined aggregate content. Validity of the models was confirmed using
the standard deviation and coefficient of determination. The models will be very useful especially to block
producers in Nigeria in predicting the other properties of the blocks given that, in most instances, only the
compressive test is carried out.
Keywords: Sand-quarry dust block, Compressive strength, Water absorption, Flexural strength, Split tensile
Strength, Regression analyses,
I. Introduction
In most concrete tests, major emphasis is placed on the determination of the 28 day compressive
strength. Often, not much is done to determine the values of the other parameters; the general assumption being
that the compressive strength gives a good summary of the overall behavior of the concrete in all conditions
they may be exposed to during their lifetime. This generalization has been found not to be always true, most
especially with regards to the durability properties [1]. The use of compressive strength as the sole parameter for
determining the quality of concrete has not only been attributed to the ease of carrying out the compressive
strength test but also to the fact that the determination of the other parameters is costly, cumbersome and time
consuming [2].Compressive strength test is also the most common test made on sandcrete blocks. Although the
Nigerian Industrial Standard [3] recommended both the compressive strength and water absorption tests
forsandcrete blocks, only the former is usually performed. The standard is silent on the other parameters as the
flexural strength which may be necessary in determining the stress at which cracks will develop in bending. If
the compressive strength is the only test to be performed based on economic considerations, it becomes
imperative that mathematical relationships which relate the compressive strength to the other structural
properties be established. Not much literature exist on the mathematical relationship between the compressive
strength and the other properties of sandcrete blocks. Danso [4] studied the variation of flexural strength and
some other block properties of sandcrete blocks with compressive strength. He did not, however extend it to
when there is partial replacement of the sand with quarry dust (sand-quarry dust blocks), a practice which is now
popular with some block producers in Nigeria. The inclusion of quarry dust as a partial replacement of sand in
sandcrete block has been shown to improve the structural properties of the blocks [5, 6].
The objective of this work is to establish simple mathematical relationships between the compressive
strength and other properties of sand-quarry dust blocks, notably flexural strength, split tensile strength and
water absorption. Regression analyses will be employed to data obtained from tests on appropriate specimens. In
the absence of any other test other than the compressive strength test the developed relationships, if any, can be
used to estimate the other parameters of the block and thus help selecting mixes that meet given requirements.
II. Materials and Methods
The materials used for this work are Water, Cement, Sand and Quarry dust. Potable water obtained
from a borehole was used in all the processes of manufacture and curing of blocks. Ibeto brand of Ordinary
Portland cement which conforms to NIS 444 [7] was used. The river sand has a specific gravity of 2.65, bulk
density of 1564kg/m3
and fineness modulus of 2.76. The corresponding values for the quarry dust are 2.74,
1296kg/m3
and 2.97.

Mathematical Relationships between the Compressive Strength and Some Other Structural ….
1.1 Mix Proportions
Batching of the constituents was by weight. Fifteen different mixes with cement/combined aggregate
ratios ranging from 1: 6 to 1: 10 and percentage replacement of sand with quarry dust of 10 to 40 were used for
testing each property. The aggregates were batched in their dry condition.
1.2 Sample preparations and testing
(a) Compressive strength and Water absorption
Ninety hollow block samples, 450 x 225 x 225mm were used for the compressive strength and water absorption
tests. The blocks were made using a Rosa Commetta block moulding machine. The compressive strength, fc
was determined from the relationship:
F and A are the failure load and cross sectional area respectively.
The water absorption test on cured blocks was in accordance to BS 1881-122 [8]. The water absorption, (Wa) of
the block was calculated as the difference between the mass of the saturated block, Mw and the dry mass, Md
expressed as a percentage of the dry mass. That is:
Forty five of the blocks each were used for the compressive strength and water absorption tests.
(b) Flexural strength
The flexural strength test was done in accordance to BS EN 12390-5 [9] using test specimens of 600 x 150 x
150mm dimensions that were prepared in accordance to BS EN 12390-1 [10]. The specimens were cured for 28
days by completely immersing them in water. The three point load system was used and the flexural strength
determined using the relationship:
Where: ff=flexural strength, F = the failure load, a = span, b = width of the beam, d = the depth of the beam.
The flexural strength for each mix ratio was taken as the average of three test results
(c) Split tensile strength
The split tensile strength test was carried out on cylinders, 300 x 150mm diameter in accordance BS EN 12390-
6 [10]. The split tensile stress was calculated using the relationship
Where: fstis the split tensile strength, F is the failure load, L is the length of specimen and d is the diameter of
the specimen.
Three samples were produced for each mix ratio and the average result taken as the split tensile strength for the
mix.
III. Results and Discussion
The results of the various tests on the structural characteristics of the sand-quarry dust blocks for the fifteen mix
ratios are shown in Table 1.
Regression analyseswereperformed using Minitab Release 16 [12] to establish empirical linear and quadratic
relationships betweenthecompressivestrength and each of the other three parameters. Figures 1-3 show the
variation of water absorption, flexural strength and split tensile strength with compressive strength
respectively.
The developed relationships for water absorption are respectively given as:
The standard error of
regression, S, are 0.270 and 0.124% while the coefficient of determination, R2
are 0.96 and 0.99 respectively.
The linear and quadratic relationships for flexural strength are given respectively as:
The values of S are respectively 0.144Nmm-2
and 0.147Nmm-2
; the corresponding values of R2
being 0.93 and
0.94.

5.55.04.54.03.53.0
8
7
6
5
4
3
fc (N/sq. mm)
Wa(%)
S 0.270069
R-Sq 96.5%
R-Sq(adj) 96.2%
Wa = 12.2973 - 1.8004fc
Table 1. Experimental test results
S/No Component proportions Block Characteristics
Water Cement Sand Quarry dust fc
(Nmm-2
)
ff
(Nmm-2
)
fst
(Nmm-2
)
Wa
(%)
1 0.520 1 5.4 0.6 4.57 3.68 2.92 4.16
2 0.805 1 4.8 3.2 3.50 2.77 2.48 5.48
3 0.620 1 5.7 1.3 3.67 3.28 2.80 5.41
4 0.720 1 6.0 2.0 3.37 2.79 2.50 6.07
5 0.860 1 6.0 3.0 3.19 2.57 2.39 6.53
6 0.750 1 9.0 1.0 2.76 2.47 2.28 7.86
7 0.875 1 7.5 2.5 3.07 2.69 2.43 6.86
8 0.735 1 7.5 1.5 3.04 2.57 2.35 6.95
9 0.680 1 6.3 1.7 3.39 2.69 2.43 6.02
10 1.000 1 6.0 4.0 2.91 2.68 2.43 7.25
11 0.610 1 3.6 2.4 5.27 4.33 3.33 3.20
12 0.760 1 5.7 2.3 3.20 2.90 2.56 6.50
13 0.635 1 7.2 0.8 3.09 2.81 2.51 6.80
14 0.565 1 4.5 1.5 4.91 3.82 3.12 3.54
15 0.665 1 4.8 2.2 4.01 3.44 2.79 4.78
The linear and quadratic relationships between the compressive strength and Split tensile strength are
respectively:
Values of S and R2
for the linear model are 0.083Nmm-2
and 0.931 respectively. The corresponding values for
the quadratic model are 0.084 and 0.934.
The adequacy of the models can be determined using the S and R2
statistics. All the models have very low S
values. The R2
values are also greater than 0.9 for all the models. The low S and R2
values indicate the adequacy
of the models. There is also not much difference between the S and R2
values for linear and quadratic models.
Each of them can be used for predicting the 28 day response of the parameter in question. However, given their
simplicity, the linear models may be preferred.
(a) Linear fit (b) Quadratic fit
Fig. 1 Variation of Water absorption with Compressive strength
5.55.04.54.03.53.0
8
7
6
5
4
3
fc (N/sq. mm)
Wa(%)
S 0.124371
R-Sq 99.3%
R-Sq(adj) 99.2%
Wa = 19.8396 - 5.7589 fc + 0.4971fc**2

5.55.04.54.03.53.0
4.5
4.0
3.5
3.0
2.5
fc (N/sq. mm)
ff(N/sq.mm)
S 0.144526
R-Sq 93.6%
R-Sq(adj) 93.1%
ff = 0.4921 + 0.7069 fc
5.55.04.54.03.53.0
3.4
3.2
3.0
2.8
2.6
2.4
2.2
fc (N/sq. mm)
fst(N/sq.mm)
S 0.0830371
R-Sq 93.1%
R-Sq(adj) 92.6%
fst = 1.216 + 0.3908 fc
Fig. 2Variation of Flexural strength with Compressive strength
Fig. 3Variation of Split tensile strength with Compressive strength
IV. Conclusion and Recommendation
Linear and quadratic models that relate the water absorption, flexural strength and split tensile strength
to the compressive strength of sand-quarry dust blocks were developed. There is an inverse proportionality
relationship between compressive strength and water absorption whereas the flexural strength and split tensile
strength of the blocks are proportional to the compressive strength. The models were developed for the range of
mixes normally employed in sandcrete block production. It is recommended that where the compressive strength
is the only test made, the developed models can be used to estimate the values of the other characteristics of
blocks thus, leading to savings in time and resources. The models will especially be useful in Nigeria where
sandcrete blocks are widely used in forming walls of residential buildings.
Acknowledgement
We acknowledge the assistance of MrIfeanyiDiogu, the manager of ACI Blocks, Owerri, Nigeria in providing
us free use of the Rosa Commetta block moulding machine used for this work.
References
[1]. Neville, A. M.,Properties of Concrete 5th
ed.(Essex: Pearson Education Limited, 2011).
[2]. Al-Amoudi, O. S. B., Al-Kutti, W. A., Ahmad, S., Maslehuddin, M. Correlation between compressive strength and certain
durability indices of plain and blended cement concretes. Cement & Concrete Composites31, 2009, 672-676.
[3]. Nigerian Industrial Standards,NIS 87: Standards for Sandcrete blocks. Standard Organization of Nigeria (SON), Lagos, 2004.
[4]. Danso, A.K., Engineering properties of Ghananiansandcrete blocks, doctoral diss., Civil Engineering Department, Kwame
Nkrumah University of Science and Technology, Ghana, 2005.
[5]. Oyekan, G. L. and Kamiyo, O. M., Effects of Granite Fines on the Structural and Hygrothermal Properties of Sandcrete Blocks.
Journal of Engineering and Applied Sciences 3(9), 2008, 735 - 741.
[6]. Olaniyan, O. S, Afolabi, O. M., Okeyinka, O. M., Granite fines as a partial replacement for sand in sandcrete block production.
International journal of Engineering and Technology, 2 (8), 2012, 1392-1394.
5.55.04.54.03.53.0
4.5
4.0
3.5
3.0
2.5
fc (N/sq. mm)
ff(N/sq.mm)
S 0.147196
R-Sq 93.9%
R-Sq(adj) 92.9%
ff = 1.4200 + 0.2199 fc + 0.0612fc**2
5.55.04.54.03.53.0
3.4
3.2
3.0
2.8
2.6
2.4
2.2
fc (N/sq. mm)
fst(N/sq.mm)
S 0.0844904
R-Sq 93.4%
R-Sq(adj) 92.3%
fst = 1.7603 + 0.10501fc + 03588fc**2

[7]. Nigerian Industrial Standards, NIS 444: Quality standard for Ordinary Portland cement. Standard Organization of Nigeria (SON),
Lagos, 2003.
[8]. British Standard Institution, BS 1881-122. Testing concrete. Method for determining of water absorption. London,1983.
[9]. British Standard Institution, BS EN 12390-5. Testing hardened concrete. Flexural strength of test specimens. London, 2009.
[10]. British Standard Institution, BS EN 12390 -1. Testing hardened concrete. Shape, dimensions and other requirements for specimens
and molds. London, 2000.
[11]. British Standard Institution. BS EN 12390 - 6.Testing hardened concrete. Tensile splitting strength test of specimens. London, 2009
[12]. Minitab Inc.,Minitab Statistical Software Release 16, Minitab Inc. State College Pennsylvania, 2010.

Mathematical Relationships between the Compressive Strength and Some Other Structural Properties of Sand-Quarry Dust Blocks

More Related Content

What's hot (19)

Viewers also liked (20)

Similar to Mathematical Relationships between the Compressive Strength and Some Other Structural Properties of Sand-Quarry Dust Blocks (20)

More from IOSR Journals (20)

Recently uploaded (20)

Mathematical Relationships between the Compressive Strength and Some Other Structural Properties of Sand-Quarry Dust Blocks