Motor driver
Download as PPTX, PDF12 likes9,848 views
An H-bridge circuit allows voltage to be applied across a motor in either direction, enabling full control over the motor's direction and speed. It is commonly used with a motor driver integrated circuit like the L293D or L298, which contains H-bridge components and can switch higher motor currents than a microcontroller alone. These ICs act as switches to control two DC motors independently according to the logic applied to their inputs.
Motor driver
- 2. Relays A relay is an electrically operated switch All electrical relays have one thing in common--they control things where it is inconvenient or impossible for a person to flip a switch. For example, electrical relays are used to turn on the motor to open an automatic garage door, as well as to turn on a furnace.
- 3. Relay vs H bridge A "double pole double throw" relay can generally achieve the same electrical functionality as an H- bridge, but an H-bridge would be preferable where a smaller physical size is needed, high speed switching, low driving voltage, or where the wearing out of mechanical parts is undesirable.
- 4. H Bridge It is an electronic circuit which enables a voltage to be applied across a load in either direction. It allows a circuit full control over a standard electric DC motor. That is, with an H-bridge, a microcontroller, logic chip, or remote control can electronically command the motor to go forward, reverse, brake, and coast.
- 5. H-bridges are available as integrated circuits, or can be built from discrete components. The term "H-bridge" is derived from the typical graphical representation of such a circuit, which is built with four switches, either solid-state (eg, L293/ L298) or mechanical (eg, relays).
- 6. S1 S2 S3 S4 Result 1 0 0 1 Motor rotates in one direction 0 1 1 0 Motor rotates in opposite direction 0 0 0 0 Motor free runs (coasts) 0 1 0 1 Motor brakes 1 0 1 0 Motor brakes
- 7. To power the motor, you turn on two switches that are diagonally opposed.
- 8. Need The current provided by the MCU is of the order of 5mA and that required by a motor is ~500mA. Hence, motor can’t be controlled directly by MCU and we need an interface between the MCU and the motor. A Motor Driver IC like L293D or L298 is used for this purpose which has two H-bridge drivers. Hence, each IC can drive two motors
- 9. Note that a motor driver does not amplify the current; it only acts as a switch (An H bridge is nothing but 4 switches).
- 11. L293 vs L298 L293 is quadruple half-H driver while L298 is dual full-H driver, i.e, in L293 all four input- output lines are independent while in L298, a half H driver cannot be used independently, only full H driver has to be used. Output current per channel = 1A for L293 and 2A for L298. Hence, heat sink is provided in L298. Protective Diodes against back EMF are provided internally in L293D but must be provided externally in L298.
- 12. Motor Driver
- 14. Drivers are enabled in pairs, with drivers 1 and 2 being enabled by the Enable pin. When an enable input is high (logic 1 or +5V), the associated drivers are enabled and their outputs are active and in phase with their inputs. When the enable pin is low, the output is neither high nor low (disconnected), irrespective of the input. Direction of the motor is controlled by asserting one of the inputs to motor to be high (logic 1) and the other to be low (logic 0). To move the motor in opposite direction just interchange the logic applied to the two inputs of the motors.
- 15. Asserting both inputs to logic high or logic low will stop the motor. Difference between L293NE and L293D: Output current per channel = 1A for L293 and 600mA for L293D. Vs is used to power the motors while Vss powers the L293NE.
- 16. Speed Control: To control motor speed we can use pulse width modulation (PWM), applied to the enable pins of L293 driver. PWM is the scheme in which the duty cycle of a square wave output from the microcontroller is varied to provide a varying average DC output.
- 17. What actually happens by applying a PWM pulse is that the motor is switched ON and OFF at a given frequency. In this way, the motor reacts to the time average of the power supply
- 20. Motor Driver Circuit on a PCB